Enhanced catalytic oxidation of 2,4-dichlorophenol via singlet oxygen dominated peroxymonosulfate activation on CoOOH@Bi2O3 composite

• Bi₂O₃ cannot directly activate PMS. • Bi₂O₃ loading increased the specific surface area and conductivity of CoOOH. • Larger specific surface area provided more active sites for PMS activation. • Faster electron transfer rate promoted the generation of reactive oxygen species. • ¹O₂ was identified as dominant ROS in the CoOOH@Bi₂O₃/PMS system. Cobalt oxyhydroxide (CoOOH) has been turned out to be a high-efficiency catalyst for peroxymonosulfate (PMS) activation. In this study, CoOOH was loaded on bismuth oxide (Bi₂O₃) using a facile chemical precipitation process to improve its catalytic activity and stability. The result showed that the catalytic performance on the 2,4-dichlorophenol (2,4-DCP) degradation was significantly enhanced with only 11 wt% Bi₂O₃ loading. The degradation rate in the CoOOH@Bi₂O₃/PMS system (0.2011 min⁻¹) was nearly 6.0 times higher than that in the CoOOH/PMS system (0.0337 min⁻¹). Furthermore, CoOOH@Bi₂O₃ displayed better stability with less Co ions leaching (16.4% lower than CoOOH) in the PMS system. These phenomena were attributed to the Bi₂O₃ loading which significantly increased the conductivity and specific surface area of the CoOOH@Bi₂O₃ composite. Faster electron transfer facilitated the redox reaction of Co (III) / Co (II) and thus was more favorable for reactive oxygen species (ROS) generation. Meanwhile, larger specific surface area furnished more active sites for PMS activation. More importantly, there were both non-radical (¹O₂) and radicals (SO₄⁻•, O₂⁻•, and OH•) in the CoOOH@Bi₂O₃/PMS system and ¹O₂ was the dominant one. In general, this study provided a simple and practical strategy to enhance the catalytic activity and stability of cobalt oxyhydroxide in the PMS system.     

Preparation of nZVI embedded modified mesoporous carbon for catalytic persulfate to degradation of reactive black 5

• The MCNZVI is prepared as an interesting material for PS activation. • Graphitized carbon shells facilitate electron transfer from Fe⁰. • The MCNZVI exhibits excellent performance to degrade RB5 by ¹O₂. • The MCNZVI has high stability and reusability in the oxidation system. High-efficiency and cost-effective catalysts with available strategies for persulfate (PS) activation are critical for the complete mineralization of organic contaminants in the environmental remediation and protection fields. A nanoscale zero-valent iron-embedded modified mesoporous carbon (MCNZVI) with a core-shell structure is synthesized using the hydrothermal synthesis method and high-temperature pyrolysis. The results showed that nZVI could be impregnated within mesoporous carbon frameworks with a comparatively high graphitization degree, rich nitrogen doping content, and a large surface area and pore volume. This material was used as a persulfate activator for the oxidation removal of Reactive Black 5 (RB5). The effects of the material dosage, PS concentration, pH, and some inorganic anions (i.e., Cl⁻, SO₄²⁻) on RB5 degradation were then investigated. The highest degradation efficiency (97.3%) of RB5 was achieved via PS (20 mmol/L) activation by the MCNZVI (0.5 g/L). The pseudo-first-order kinetics (k = 2.11 × 10⁻² min⁻¹) in the MCNZVI/PS (0.5 g/L, 20 mmol/L) was greater than 100 times than that in the MCNZVI and PS. The reactive oxygen species (ROS), including ¹O₂, SO₄^·−, HO^·, and ·O₂⁻, were generated by PS activation with the MCNZVI. Singlet oxygen was demonstrated to be the primary ROS responsible for the RB5 degradation. The MCNZVI could be reused and regenerated for recycling. This work provides new insights into PS activation to remove organic contamination.     

Elimination of antibiotic resistance genes and control of horizontal transfer risk by UV-based treatment of drinking water: A mini review

Antibiotic-resistant bacteria and antibiotic resistance genes are in water bodies. UV/chlorination method is better to remove ARGs than UV or chlorination alone. Research on UV/hydrogen peroxide to eliminate ARGs is forthcoming. UV-based photocatalytic processes are effective to degrade ARGs. Antibiotic-resistant bacteria (ARB) and antibiotic resistance genes (ARGs) have been recognized as one of the biggest public health issues of the 21st century. Both ARB and ARGs have been determined in water after treatment with conventional disinfectants. Ultraviolet (UV) technology has been seen growth in application to disinfect the water. However, UV method alone is not adequate to degrade ARGs in water. Researchers are investigating the combination of UV with other oxidants (chlorine, hydrogen peroxide (H₂O₂), peroxymonosulfate (PMS), and photocatalysts) to harness the high reactivity of produced reactive species (Clž·, ClOž·ž, Clž₂·ž⁻, žž·OH, and SOž₄ž·⁻€) in such processes with constituents of cell (e.g., deoxyribonucleic acid (DNA) and its components) in order to increase the degradation efficiency of ARGs. This paper briefly reviews the current status of different UV-based treatments (UV/chlorination, UV/H₂O₂, UV/PMS, and UV-photocatalysis) to degrade ARGs and to control horizontal gene transfer (HGT) in water. The review also provides discussion on the mechanism of degradation of ARGs and application of q-PCR and gel electrophoresis to obtain insights of the fate of ARGs during UV-based treatment processes.     

Enhanced carbon tetrachloride degradation by hydroxylamine in ferrous ion activated calcium peroxide in the presence of formic acid

• Complete CT degradation was achieved by employing HA to CP/Fe(II)/FA process. • Quantitative detection of Fe(II) regeneration and HO• production was investigated. • Benzoic acid outcompeted FA for the reaction with HO•. • CO₂•⁻ was the dominant reductive radical for CT removal. • Effects of solution matrix on CT removal were conducted. Hydroxyl radicals (HO•) show low reactivity with perchlorinated hydrocarbons, such as carbon tetrachloride (CT), in conventional Fenton reactions, therefore, the generation of reductive radicals has attracted increasing attention. This study investigated the enhancement of CT degradation by the synergistic effects of hydroxylamine (HA) and formic acid (FA) (initial [CT] = 0.13 mmol/L) in a Fe(II) activated calcium peroxide (CP) Fenton process. CT degradation increased from 56.6% to 99.9% with the addition of 0.78 mmol/L HA to the CP/Fe(II)/FA/CT process in a molar ratio of 12/6/12/1. The results also showed that the presence of HA enhanced the regeneration of Fe(II) from Fe(III), and the production of HO• increased one-fold when employing benzoic acid as the HO• probe. Additionally, FA slightly improves the production of HO•. A study of the mechanism confirmed that the carbon dioxide radical (CO₂•⁻), a strong reductant generated by the reaction between FA and HO•, was the dominant radical responsible for CT degradation. Almost complete CT dechlorination was achieved in the process. The presence of humic acid and chloride ion slightly decreased CT removal, while high doses of bicarbonate and high pH inhibited CT degradation. This study helps us to better understand the synergistic roles of FA and HA for HO• and CO₂•⁻ generation and the removal of perchlorinated hydrocarbons in modified Fenton systems.     

Fe2O3-CeO2-Bi2O3/γ-Al2O3 catalyst in the catalytic wet air oxidation (CWAO) of cationic red GTL under mild reaction conditions

Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃, an environmental friendly material, was investigated. The catalyst exhibited good catalytic performance in the CWAO of cationic red GTL. The apparent activation energy for the reaction was 79 kJ·mol⁻¹. HO₂· and O₂·⁻ appeared as the main reactive species in the reaction. The Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃ catalyst, a novel environmental-friendly material, was used to investigate the catalytic wet air oxidation (CWAO) of cationic red GTL under mild operating conditions in a batch reactor. The catalyst was prepared by wet impregnation, and characterized by special surface area (BET measurement), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃ catalyst exhibited good catalytic activity and stability in the CWAO under atmosphere pressure. The effect of the reaction conditions (catalyst loading, degradation temperature, solution concentration and initial solution pH value) was studied. The result showed that the decolorization efficiency of cationic red GTL was improved with increasing the initial solution pH value and the degradation temperature. The apparent activation energy for the reaction was 79 kJ·mol⁻¹. Hydroperoxy radicals (HO₂·) and superoxide radicals (O₂⁻·) appeared as the main reactive species upon the CWAO of cationic red GTL.     

Persistent free radicals in humin under redox conditions and their impact in transforming polycyclic aromatic hydrocarbons

• Regulation of redox conditions promotes the generation of free radicals on HM. • HM-PFRs can be fractionated into active and inactive types depending on stability. • The newly produced PFRs readily release electrons to oxygen and generate ROS. • PFR-induced ROS mediate the transformation of organic contaminants adsorbed on HM. The role of humic substance-associated persistent free radicals (PFRs) in the fate of organic contaminants under various redox conditions remains unknown. This study examined the characterization of original metal-free peat humin (HM), and HM treated with varying concentrations of H₂O₂ and L-ascorbic acid (VC) (assigned as H₂O₂-HM and VC-HM). The concentration of PFRs in HM increased with the addition of VC/H₂O₂ at concentrations less than 0.08 M. The evolution of PFRs in HM under different environmental conditions (e.g., oxic/anoxic and humidity) was investigated. Two types of PFRs were detected in HM: a relatively stable radical existed in the original sample, and the other type, which was generated by redox treatments, was relatively unstable. The spin densities of VC/H₂O₂-HM readily returned to the original value under relatively high humidity and oxic conditions. During this process, the HM-associated “unstable” free radicals released an electron to O₂, inducing the formation of reactive oxygen species (ROS, i.e., ^•OH and ^•O₂⁻). The generated ROS promoted the degradation of polycyclic aromatic hydrocarbons based on the radical quenching measurements. The transformation rates followed the order naphthalene>phenanthrene>anthracene>benzo[a]pyrene. Our results provide valuable insight into the HM-induced transformation of organic contaminants under natural conditions.     

Contributions of adsorption,bioreduction and desorption to uranium immobilization by extracellular polymeric substances

● EPS immobilizes U(VI) via adsorption, bioreduction and desorption. ● This work provides a framework to quantify the three immobilization processes. ● The non-equilibrium adsorption of U follows pseudo-second-order kinetics. ● The equilibrium adsorption of U followed Langmuir and Freundlich isotherms. Hexavalent uranium (U(VI)) can be immobilized by various microbes. The role of extracellular polymeric substances (EPS) in U(VI) immobilization has not been quantified. This work provides a model framework to quantify the contributions of three processes involved in EPS-mediated U(VI) immobilization: adsorption, bioreduction and desorption. Loosely associated EPS was extracted from a pure bacterial strain, Klebsiella sp. J1, and then exposed to H₂ and O₂ (no bioreduction control) to immobilize U(VI) in batch experiments. U(VI) immobilization was faster when exposed to H₂ than O₂ and stabilized at 94% for H₂ and 85% for O₂, respectively. The non-equilibrium data from the H₂ experiments were best simulated by a kinetic model consisting of pseudo-second-order adsorption (k_a = 2.87 × 10⁻³ g EPS·(mg U)⁻¹·min⁻¹), first-order bioreduction (k_b = 0.112 min⁻¹) and first-order desorption (k_d = 7.00 × 10⁻³ min⁻¹) and fitted the experimental data with R² of 0.999. While adsorption was dominant in the first minute of the experiments with H₂, bioreduction was dominant from the second minute to the 50^th min. After 50 min, adsorption was negligible, and bioreduction was balanced by desorption. This work also provides the first set of equilibrium data for U(VI) adsorption by EPS alone. The equilibrium experiments with O₂ were well simulated by both the Langmuir isotherm and the Freundlich isotherm, suggesting multiple mechanisms involved in the interactions between U(VI) and EPS. The thermodynamic study indicated that the adsorption of U(VI) onto EPS was endothermic, spontaneous and favorable at higher temperatures.     

Ozonation of the 5-fluorouracil anticancer drug and its prodrug capecitabine: Reaction kinetics,oxidation mechanisms,and residual toxicity

Specific second-order rate constants were determined for 5-FU and CAP with ozone. Reaction sites were confirmed by kinetics, Fukui analysis, and products. The olefin moiety was the main ozone reaction site for 5-FU and CAP. Carboxylic acids comprised most of the residual TOC for 5-FU. Ozonation removed the toxicity associated with 5-FU and products but not CAP. Anticancer drugs (ADs) have been detected in the environment and represent a risk to aquatic organisms, necessitating AD removal in drinking water and wastewater treatment. In this study, ozonation of the most commonly used antimetabolite ADs, namely 5-fluorouracil (5-FU) and its prodrug capecitabine (CAP), was investigated to determine reaction kinetics, oxidation mechanisms, and residual toxicity. The specific second-order rate constants between aqueous ozone and 5-FU, 5-FU⁻, 5-FU²⁻, CAP, and CAP⁻ were determined to be 7.07(±0.11)×10⁴ M⁻¹·s⁻¹, 1.36(±0.06)×10⁶ M⁻¹·s⁻¹, 2.62(±0.17)×10⁷ M⁻¹·s⁻¹, 9.69(±0.08)×10³ M⁻¹·s⁻¹, and 4.28(±0.07)×10⁵ M⁻¹·s⁻¹, respectively; furthermore, the second-order rate constants for ^•OH reaction with 5-FU and CAP at pH 7 were determined to be 1.85(±0.20)×10⁹ M⁻¹·s⁻¹ and 9.95(±0.26)×10⁹ M⁻¹·s⁻¹, respectively. Density functional theory was used to predict the main ozone reaction sites of 5-FU (olefin) and CAP (olefin and deprotonated secondary amine), and these mechanisms were supported by the identified transformation products. Carboxylic acids constituted a majority of the residual organic matter for 5-FU ozonation; however, carboxylic acids and aldehydes were important components of the residual organic matter generated by CAP. Ozone removed the toxicity of 5-FU to Vibrio fischeri, but the residual toxicity of ozonated CAP solutions exhibited an initial increase before subsequent removal. Ultimately, these results suggest that ozone is a suitable technology for treatment of 5-FU and CAP, although the residual toxicity of transformation products must be carefully considered.     

Oxidation and biotoxicity assessment of microcystin-LR using different AOPs based on UV,O3 and H2O2

MC-LR removal performances under different AOPs were compared systematically. Higher removal efficiency and synergistic effects were obtained by combined process. The acute biotoxicity raised in different degrees after oxidation. Microcystin-LR attracts attention due to its high toxicity, high concentration and high frequency. The removal characteristics of UV/H₂O₂ and O₃/H₂O₂ advanced oxidation processes and their individual process for MC-LR were investigated and compared in this study. Both the removal efficiencies and rates of MC-LR as well as the biotoxicity of degradation products was analyzed. Results showed that the UV/H₂O₂ process and O₃/H₂O₂ were effective methods to remove MC-LR from water, and they two performed better than UV-, O₃-, H₂O₂-alone processes under the same conditions. The effects of UV intensity, H₂O₂ concentration and O₃ concentration on the removal performance were explored. The synergistic effects between UV and H₂O₂, O₃ and H₂O₂ were observed. UV dosage of 1800 mJ·cm⁻² was required to remove 90% of 100 mg·L⁻¹ MC-LR, which amount significantly decreased to 500 mJ·cm⁻² when 1.7 mg·L⁻¹ H₂O₂ was added. 0.25 mg·L⁻¹ O₃, or 0.125 mg·L⁻¹ O₃ with 1.7 mg·L⁻¹ H₂O₂ was needed to reach 90% removal efficiency. Furthermore, the biotoxicity results about these UV/H₂O₂, O₃/H₂O₂ and O₃-alone processes all present rising trends with oxidation degree of MC-LR. Biotoxicity of solution, equivalent to 0.01 mg·L⁻¹ Zn²⁺, raised to 0.05 mg·L⁻¹ Zn²⁺ after UV/H₂O₂ or O₃/H₂O₂ reaction. This phenomenon may be attributed to the aldehydes and ketones with small molecular weight generated during reaction. Advice about the selection of MC-LR removal methods in real cases was provided.     

Hydroxyl radical intensified Cu2O NPs/H2O2 process in ceramic membrane reactor for degradation on DMAc wastewater from polymeric membrane manufacturer

• Cu₂O NPs/H₂O₂ Fenton process was intensified by membrane dispersion. • DMAc removal was enhanced to 98% for initial DMAc of 14000 mg/L. • Analyzed time-resolved degradation pathway of DMAc under ·OH attack. High-concentration industrial wastewater containing N,N-dimethylacetamide (DMAc) from polymeric membrane manufacturer was degraded in Cu₂O NPs/H₂O₂ Fenton process. In the membrane-assisted Fenton process DMAc removal rate was up to 98% with 120 min which was increased by 23% over the batch reactor. It was found that ·OH quench time was extended by 20 min and the maximum ·OH productivity was notably 88.7% higher at 40 min. The degradation reaction rate constant was enhanced by 2.2 times with membrane dispersion (k = 0.0349 min⁻¹). DMAc initial concentration (C₀) and H₂O₂ flux (J_p) had major influence on mass transfer and kinetics, meanwhile, membrane pore size (r_p) and length (L_m) also affected the reaction rate. The intensified radical yield, fast mass transfer and nanoparticles high activity all contributed to improve pollutant degradation efficiency. Time-resolved DMAc degradation pathway was analyzed as hydroxylation, demethylation and oxidation leading to the final products of CO₂, H₂O and NO₃⁻ (rather than NH₃ from biodegradation). Continuous process was operated in the dual-membrane configuration with in situ reaction and separation. After five cycling tests, DMAc removal was all above 95% for the initial [DMAc]₀ = 14,000 mg/L in wastewater and stability of the catalyst and the membrane maintained well.     

Visible-light-driven heterostructured g-C3N4/Bi-TiO2 floating photocatalyst with enhanced charge carrier separation for photocatalytic inactivation of Microcystis aeruginosa

• Bi doping in TiO₂ enhanced the separation of photo-generated electron-hole. • The performance of photocatalytic degradation of MC-LR was improved. • Coexisting substances have no influence on algal removal performance. • The key reactive oxygen species were h⁺ and ^•OH in the photocatalytic process. The increase in occurrence and severity of cyanobacteria blooms is causing increasing concern; moreover, human and animal health is affected by the toxic effects of Microcystin-LR released into the water. In this paper, a floating photocatalyst for the photocatalytic inactivation of the harmful algae Microcystis aeruginosa (M. aeruginosa) was prepared using a simple sol-gel method, i.e., coating g-C₃N₄ coupled with Bi-doped TiO₂ on Al₂O₃-modified expanded perlite (CBTA for short). The impact of different molar ratios of Bi/Ti on CBTA was considered. The results indicated that Bi doping in TiO₂ inhibited photogenerated electron-hole pair recombination. With 6 h of visible light illumination, 75.9% of M. aeruginosa (initial concentration= 2.7 × 10⁶ cells/L) and 83.7% of Microcystin-LR (initial concentration= 100 μg/L) could be removed with the addition of 2 g/L CBTA-1% (i.e., Bi/Ti molar ratio= 1%). The key reactive oxygen species (ROSs) in the photocatalytic inactivation process are h⁺ and ^•OH. The induction of the Bi⁴⁺/Bi³⁺ species by the incorporation of Bi could narrow the bandgap of TiO₂, trap electrons, and enhance the stability of CBTA-1% in the solutions with coexisting environmental substances.     

New method for efficient control of hydrogen sulfide and methane in gravity sewers: Combination of NaOH and nitrite

• The combination of NaOH and nitrite was used to control harmful gas in sewers. • Hydrogen sulfide and methane in airspace were reduced by 96.01% and 91.49%. • Changes in sewage quality and greenhouse effect by chemical dosing were negligible. • The strong destructive effects on biofilm slowed down the recovery of harmful gases. • The cost of the method was only 3.92 × 10⁻³ $/m³. An innovative treatment method by the combination of NaOH and nitrite is proposed for controlling hydrogen sulfide and methane in gravity sewers and overcome the drawbacks of the conventional single chemical treatment. Four reactors simulating gravity sewers were set up to assess the effectiveness of the proposed method. Findings demonstrated hydrogen sulfide and methane reductions of about 96.01% and 91.49%, respectively, by the combined addition of NaOH and nitrite. The consumption of NaNO₂ decreased by 42.90%, and the consumption rate of NaOH also showed a downward trend. Compared with a single application of NaNO₂, the C/N ratio of wastewater was increased to about 0.61 mg COD/mg N. The greenhouse effect of intermediate N₂O and residual methane was about 48.80 gCO₂/m³, which is far lower than that of methane without control (260 gCO₂/m³). Biofilm was destroyed to prevent it from entering the sewage by the chemical additives, which reduced the biomass and inhibited the recovery of biofilm activity to prolong the control time. The sulfide production rate and sulfate reduction rate were reduced by 92.32% and 85.28%, respectively. Compared with conventional control methods, the cost of this new method was only 3.92 × 10⁻³ $/m³, which is potentially a cost-effective strategy for sulfide and methane control in gravity sewers.     

Enhanced triallyl isocyanurate (TAIC) degradation through application of an O3/UV process: Performance optimization and degradation pathways

• UV/O₃ process had higher TAIC mineralization rate than O₃ process. • Four possible degradation pathways were proposed during TAIC degradation. • pH impacted oxidation processes with pH of 9 achieving maximum efficiency. • CO₃^2– negatively impacted TAIC degradation while HCO₃^– not. • Cl^– can be radicals scavenger only at high concentration (over 500 mg/L Cl^–). Triallyl isocyanurate (TAIC, C₁₂H₁₅N₃O₃) has featured in wastewater treatment as a refractory organic compound due to the significant production capability and negative environmental impact. TAIC degradation was enhanced when an ozone(O₃)/ultraviolet(UV) process was applied compared with the application of an independent O₃ process. Although 99% of TAIC could be degraded in 5 min during both processes, the O₃/UV process had a 70%mineralization rate that was much higher than that of the independent O₃ process (9%) in 30 min. Four possible degradation pathways were proposed based on the organic compounds of intermediate products identified during TAIC degradation through the application of independent O₃ and O₃/UV processes. pH impacted both the direct and indirect oxidation processes. Acidic and alkaline conditions preferred direct and indirect reactions respectively, with a pH of 9 achieving maximum Total Organic Carbon (TOC) removal. Both CO₃^2– and HCO₃^– decreased TOC removal, however only CO₃^2– negatively impacted TAIC degradation. Effects of Cl^– as a radical scavenger became more marked only at high concentrations (over 500 mg/L Cl^–). Particulate and suspended matter could hinder the transmission of ultraviolet light and reduce the production of HO· accordingly.     

Zero-valent manganese nanoparticles coupled with different strong oxidants for thallium removal from wastewater

• Nano zero-valent manganese (nZVMn, Mn⁰) is synthesized via borohydrides reduction. • Mn⁰ combined with persulfate/hypochlorite is effective for Tl removal at pH 6-12. • Mn⁰ can activate persulfate to form hydroxyl and sulfate radicals. • Oxidation-induced precipitation and surface complexation contribute to Tl removal. • Combined Mn⁰-oxidants process is promising in the environmental field. Nano zero-valent manganese (nZVMn, Mn⁰) was prepared through a borohydride reduction method and coupled with different oxidants (persulfate (S₂O₈²⁻), hypochlorite (ClO⁻), or hydrogen peroxide (H₂O₂)) to remove thallium (Tl) from wastewater. The surface of Mn⁰ was readily oxidized to form a core-shell composite (MnO_x@Mn⁰), which consists of Mn⁰ as the inner core and MnO_x (MnO, Mn₂O₃, and Mn₃O₄) as the outer layer. When Mn⁰ was added alone, effective Tl(I) removal was achieved at high pH levels (>12). The Mn⁰-H₂O₂ system was only effective in Tl(I) removal at high pH (>12), while the Mn⁰-S₂O₈²⁻ or Mn⁰-ClO⁻ system had excellent Tl(I) removal (>96%) over a broad pH range (4–12). The Mn⁰-S₂O₈²⁻ oxidation system provided the best resistance to interference from an external organic matrix. The isotherm of Tl(I) removal through the Mn⁰-S₂O₈²⁻ system followed the Freundlich model. The Mn⁰ nanomaterials can activate persulfate to produce sulfate radicals and hydroxyl radicals. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy suggested that oxidation-induced precipitation, surface adsorption, and electrostatic attraction are the main mechanisms for Tl(I) removal resulting from the combination of Mn⁰ and oxidants. Mn⁰ coupled with S₂O₈²⁻/ClO⁻ is a novel and effective technique for Tl(I) removal, and its application in other fields is worthy of further investigation.     

Co-present Pb(II) accelerates the oxidation of organic contaminants by permanganate: Role of Pb(III)

• Simultaneous removal of organic contaminants and Pb(II) was achieved by Mn(VII). • Pb(II) enhanced Mn(VII) oxidation performance over a wide pH range. • Pb(II) did not alter the pH-rate profile for contaminants oxidation by Mn(VII). • Mn(VII) alone cannot oxidize Pb(II) effectively at pH below 5.0. • Pb(III) plays important roles on enhancing Mn(VII) decontamination process. The permanganate (Mn(VII)) oxidation has emerged as a promising technology for the remediation and treatment of the groundwater and surface water contaminated with the organic compounds. Nonetheless, only a few studies have been conducted to explore the role of the heavy metals (especially the redox-active ones) during the Mn(VII) oxidation process. In this study, taking Pb(II) as an example, its influence on the Mn(VII) decontamination performance has been extensively investigated. It was found that, with the presence of Pb(II), Mn(VII) could degrade diclofenac (DCF), 2,4-dichlorophenol, and aniline more effectively than without. For instance, over a wide pH range of 4.5–8.0, the dosing of 10 μmol/L Pb(II) accelerated the DCF removal rate from 0.006–0.25 min⁻¹ to 0.05–0.46 min⁻¹ with a promotion factor of 1.9–9.4. Although the UV-vis spectroscopic and high resolution transmission electron microscopy analyses suggested that Mn(VII) could react with Pb(II) to produce Mn(IV) and Pb(IV) at pH 6.0–8.0, further experiments revealed that Pb(II) did not exert its enhancing effect through promoting the generation of MnO₂, as the reactivity of MnO₂ was poor under the employed pH range. At pH below 5.0, it was interesting to find that, a negligible amount of MnO₂ was formed in the Mn(VII)/Pb(II) system in the absence of contaminants, while once MnO₂ was generated in the presence of contaminants, it could catalyze the Pb(II) oxidation to Pb(IV) by Mn(VII). Collectively, by highlighting the conversion process of Pb(II) to Pb(IV) by either Mn(VII) or MnO₂, the reactive Pb(III) intermediates were proposed to account for the Pb(II) enhancement effect.     

Antioxidative potential of metformin: Possible protective mechanism against generating OH radicals

• Metformin consumes O₂−• and OH• induced by PM are proposed. • OH• dominated the oxidation of metformin compared with O₂−• • Metformin can prevent the harm of ROS induced by PM to human health. • Antioxidative potential of metformin was first proposed to provide measures. Exposure to particulate matter (PM) can lead to the excessive accumulation of reactive oxygen species (ROS), which causes oxidative stress and endangers human health. In this study, the effects of metformin on PM-induced radicals were investigated, and the antioxidation reaction mechanism of metformin was analyzed by the density functional theory (DFT) method. The corresponding results revealed that the consumption rate of dithiothreitol (DTT) increased as the metformin concentration (0–40 mmol/L) increased under exposure to PM active components. Moreover, the OH radical content decreased as the metformin concentration increased. This result may be related to the consumption of PM-induced OH radicals by metformin, which promotes the DTT consumption rate. Additionally, because the initiation reaction has a high barrier, the oxidation reaction rate between metformin and •O₂− is not very fast, although various catalysts may be present in the human environment. Importantly, we found that the barrier of metformin induced by OH radicals is only 9.6 kcal/mol while the barrier of metformin induced by oxygen is 57.9 kcal/mol, which shows that the rate of the •OH-initiated oxidative reaction of metformin is much faster and that this reaction path occurs more easily. By sample analysis, the mean OH radical generation was 55 nmol/min/g (ranging from 5 to 105 nmol/min/g) on haze days and 30 nmol/min/g (ranging from 10 to 50 nmol/min/g) on non-haze days. Moreover, OH radical generation was higher on haze days than on neighboring non-haze days. Taken together, all data suggest that metformin could consume the PM-induced radicals, such as OH radicals and •O₂−, thereby providing health protection.     

Occurrence of veterinary antibiotics in struvite recovery from swine wastewater by using a fluidized bed

Antibiotics in wastewater pose pharmacological threats to phosphorous recovery. Recovered struvite particles possessed significantly antibiotic residues. Smaller granules contained much more antibiotics than the larger ones. Organic matters and struvite granulation process exerted significant impacts. Recovering phosphorus from livestock wastewater has gained extensive attention. The residue of veterinary antibiotics in the wastewater may be present in the recovered products, thereby posing pharmacological threats to the agricultural planting and human health. This study investigated antibiotic occurrence in the struvite particles recovered from swine wastewater by using a fluidized bed. Results revealed that tetracyclines possessed significant residues in the struvite granules, with the values ranging from 195.2 mg·kg⁻¹ to 1995.0 mg·kg⁻¹. As for fluoroquinolones, their concentrations varied from 0.4 mg·kg⁻¹ to 1104.0 mg·kg⁻¹. Struvite particles were of various sizes and shapes and displayed different antibiotic adsorption capacities. The data also showed that the smaller granules contained much more antibiotics than the larger ones, indicating that the fluidized granulation process of struvite crystals plays an important role on the accumulation of antibiotics. For tetracyclines, organic matters and struvite adsorption exerted significant impacts on tetracyclines migration. The outcomes underscore the need to consider the residues of antibiotics in resource recovery from wastewater because they exert pharmacological impacts on the utilization of recovered products.     

Statistical modeling of radiolytic (60Co g) degradation of Ofloxacin,antibiotic: Synergetic effect,kinetic studies & assessment of its degraded metabolites

Linear, interactive and quadratic effects of process parameters were studied. Degradation of Ofloxacin (Ofx) was related with G value of irradiation process. The synergistic effect of H₂O₂ on lower dose of g-irradiation was established. The process follows pseudo first order with dose constant (d = 0.232 kGy^–1). The impact of human activities in the past few decades has paved the way for the release of pollutants due to the improper effluent treatment. Recent studies revealed that, Ofloxacin, an antibiotic as one of the major pollutant affecting surface water and ground water. In this study, the radiolytic potential of Ofloxacin was investigated. The effects of pH, dose and concentration of Ofloxacin were analyzed using One Factor At a Time (OFAT) and the interactive effects between the parameters were studied using Face Centered Central Composite Design. The statistically optimised developed model shows 30% degradation at initial antibiotic concentration of 1mM at pH 3.0 and at 2 kGy dose of gamma ray. The process efficiency was evaluated in terms of G value and its correlation with the concentration of antibiotic was also established. The process of degradation was augmented by the addition of H₂O₂ (1.5 mM). The reaction kinetics for the process was evaluated, the dose rate constant and the rate of degradation for the augmented process was found to be 0.232 kGy^-1 and 0.232 mM/kGy, respectively. The degraded metabolites of the radiolytic degradation of Ofloxacin were analyzed through change in pH, reduction in TOC and GC-MS spectrum.     

Forward osmosis coupled with lime-soda ash softening for volume minimization of reverse osmosis concentrate and CaCO3 recovery: A case study on the coal chemical industry

• Forward osmosis (FO) coupled with chemical softening for CCI ROC minimization • Effective removal of scale precursor ions by lime-soda ash softening • Enhanced water recovery from 54% to 86% by mitigation of FO membrane scaling • High-purity CaCO₃ was recovered from the softening sludge • Membrane cleaning efficiency of 88.5% was obtained by EDTA for softened ROC Reverse osmosis (RO) is frequently used for water reclamation from treated wastewater or desalination plants. The RO concentrate (ROC) produced from the coal chemical industry (CCI) generally contains refractory organic pollutants and extremely high-concentration inorganic salts with a dissolved solids content of more than 20 g/L contributed by inorganic ions, such as Na⁺, Ca²⁺, Mg²⁺, Cl⁻, and SO₄²⁻. To address this issue, in this study, we focused on coupling forward osmosis (FO) with chemical softening (FO-CS) for the volume minimization of CCI ROC and the recovery of valuable resources in the form of CaCO₃. In the case of the real raw CCI ROC, softening treatment by lime-soda ash was shown to effectively remove Ca²⁺/Ba²⁺ (>98.5%) and Mg²⁺/Sr²⁺/Si (>80%), as well as significantly mitigate membrane scaling during FO. The softened ROC and raw ROC corresponded to a maximum water recovery of 86% and 54%, respectively. During cyclic FO tests (4 × 10 h), a 27% decline in the water flux was observed for raw ROC, whereas only 4% was observed for softened ROC. The cleaning efficiency using EDTA was also found to be considerably higher for softened ROC (88.5%) than that for raw ROC (49.0%). In addition, CaCO₃ (92.2% purity) was recovered from the softening sludge with an average yield of 5.6 kg/m³ treated ROC. This study provides a proof-of-concept demonstration of the FO-CS coupling process for ROC volume minimization and valuable resources recovery, which makes the treatment of CCI ROC more efficient and more economical.