聚丙烯酸钠-硅溶胶的合成及其对阳离子金黄染料的吸附

通过简单的水溶液聚合法成功合成了聚丙烯酸钠-硅溶胶复合吸附剂,并对其进行了SEM和热重分析,研究了吸附条件对该吸附剂对阳离子金黄染料吸附效果的影响。实验结果表明,当硅溶胶质量分数为20%、初始染料质量浓度为60 mg/L、初始溶液pH为7、反应温度为298 K时,聚丙烯酸钠-硅溶胶复合吸附剂对阳离子金黄染料的吸附量为64.64 mg/g。由二级吸附动力学模型获得的活化能(Ea=2.617 kJ/mol)表明,聚丙烯酸钠-硅溶胶复合材料对阳离子金黄的吸附属于物理吸附,低温有利于吸附。     

核桃壳吸附剂对水中Pb2+的吸附

采用自制核桃壳吸附剂,利用静态吸附法,处理模拟含Pb²⁺废水。实验结果表明：当初始Pb²⁺的质量浓度20.00 mg/L、初始废水pH=5.5、吸附剂加入量12 g/L、吸附剂粒径1.60~2.50 mm、吸附时间120 min时,核桃壳吸附剂对Pb²⁺的去除率为91.7%;吸附剂对Pb²⁺的吸附行为满足拟二级吸附动力学方程,吸附等温线满足Langmuir等温方程,饱和吸附量达到3.903 mg/g;吸附饱和的吸附剂可用浓度 0.1 mol/L的硝酸解吸,经解吸后的吸附剂可重复利用3次。     

Experimental and Modeling Studies for the Removal of Crystal Violet Dye from Aqueous Solutions using Eco-friendly <Emphasis Type="Italic">Gracilaria corticata</Emphasis> Seaweed Activated Carbon/Zn/Alginate Polymeric Composite Beads

This research article describes, an eco-friendly activated carbon prepared from the Gracilaria corticata seaweeds which was employed for the preparation of biodegradable polymeric beads for the efficient removal of crystal violet dye in an aqueous solution. The presence of chemical functional groups in the adsorbent material was detected using FTIR spectroscopy. The morphology and physical phases of the adsorbent materials were analyzed using SEM and XRD studies respectively. Batch mode dye adsorption behavior of the activated carbon/Zn/alginate polymeric beads was investigated as a function of dosage, solution pH, contact time, initial dye concentration and temperature. Maximum dye removal was observed at a pH of 5.0, 1 g of adsorbent dosage with 60 mg/L dye concentration, 50 min of contact time and at 30 °C. The equilibrium modeling studies were analyzed with Freundlich and Langmuir adsorption isotherms and the adsorption dynamics was predicted with Lagergren’s pseudo-first order, pseudo-second order equations and intra particle diffusion models. The process of dye removal followed a pseudo second-order kinetics rather than pseudo first order. The thermodynamic parameters like standard Gibbs free energy change (ΔG°), enthalpy change (ΔH°) and entropy change (ΔS°) were determined and the results imply that the adsorption process was spontaneous, endothermic and increases the randomness between the adsorbent and adsorbate. The results from the experimental and correlation data reveal that the Gracilaria corticata activated carbon/Zn/alginate polymeric beads have proved to be an excellent adsorbent material for the removal of CV dye.     

Removal of fluoride from water using aluminum-modified activated carbon prepared from khat (Catha edulis) stems

This study investigated the fluoride removal efficiency and adsorption of a low-cost adsorbent prepared using aluminum-modified activated carbon from khat (Catha edulis) in a batch-mode reactor. The operating factors, including pH, adsorbent dose, and fluoride initial concentration, were optimized using the Box Behnken design of response surface methodology. The correlation coefficient (R²) for the removal of fluoride was found to be 0.93, showing the validity of the developed quadratic model. The results showed that, under optimized conditions of an adsorbent dose of 2.47 g/L, an initial fluoride concentration of 2.1 mg/L, an initial pH 6.08, and 60 min, 90% fluoride reduction was achieved. Meanwhile, the adsorption isotherm and kinetics followed the Langmuir adsorption model and the Pseudo second model, respectively, with a monolayer adsorption capacity of 0.3065 mg/g. On the other hand, Fourier transform infrared spectroscopy and scanning electron microscopy analyses revealed the formation of major peaks of components such as hydroxyl and carboxylic acids. The same optimum treatment conditions (adsorbent dose of 2.47 g/L, initial pH 6.08, and treatment time of 60 min) managed to remove low initial fluoride concentrations of 3.67 and 4.33 mg/L from real groundwater by 72.84% and 70.37%, respectively. The modified adsorbent prepared in this study successfully treat the low fluoride concentration to a level recommended by WHO for drinking water.     

聚丙烯酰-6-氨基吡啶的制备及其对重金属离子的吸附

以2,6-二氨基吡啶为原料,合成了功能单体2-丙烯酰-6-氨基吡啶,并将其与乙二醇二甲基丙烯酸酯共聚合成了聚合物吸附剂聚丙烯酰-6-氨基吡啶。考察了聚合物吸附剂对重金属离子的吸附分离性能。实验结果表明：在混合液中Cu²⁺,Zn²⁺,Cd²⁺,Ni²⁺的初始质量浓度均为10 mg/L、聚合物吸附剂加入量为5 g/L、溶液pH=7、吸附时间为10 min的条件下,聚合物吸附剂对各离子的吸附率均大于90%;采用浓度为0.5 mol/L的HCl溶液对吸附后的聚合物吸附剂进行洗脱,4种重金属离子的洗脱率均可达97%以上;该吸附剂具有很好的稳定性,重复使用11次后其对4种重金属离子的饱和吸附量均未有明显的下降。     

L-谷氨酸改性氧化石墨烯对Cu2+的吸附

采用L-谷氨酸（L-Glu）改性氧化石墨烯（GO）制备吸附剂L-Glu/GO,并进行了XRD、FTIR和SEM表征。考察了不同因素对L-Glu/GO吸附Cu²⁺的影响,并对L-Glu/GO的吸附-解吸能力进行了研究。实验结果表明：L-Glu/GO对Cu²⁺的吸附在10 min内就可达到吸附平衡;在Cu²⁺初始质量浓度为70 mg/L、初始pH为5、L-Glu/GO投加量为0.200 g/L、吸附时间为120 min、吸附温度为30 ℃的条件下,L-Glu/GO的最大吸附量可达292.460 mg/g。准二级动力学和Langmuir模型能很好地拟合此吸附过程,且显示该吸附过程可促进L-Glu/GO对Cu²⁺的吸附。热力学研究结果表明该吸附过程是一个自发的放热过程。经过5次吸附-解吸循环后,L-Glu/GO对Cu²⁺的吸附率仍在92%以上,表明该吸附剂再生性好,可重复使用。     

Effective Removing of Remazol Black B by the Polyacrylamide Cryogels Modified with Polyethyleneimine

In this study, modified polyacrylamide (PAAm) cryogels with high dye holding capacity were synthesized with an easily and cheaply process and adsorption of Remazol Black B (RBB) with the synthesized materials was investigated. Firstly, PAAm cryogels were synthesized with free radical cryo-copolymerization method and they were modified with Hofmann reaction to form amine groups in the structure of the cyrogels. Then, to increase the removal efficiency of cryogels, polyethylenimine (PEI) molecules were crosslinked onto the cryogels via NH₂ groups present in the PAAm gels modified by the Hofmann reaction. The original and modified cryogels were characterized with fourier transformed infrared spectroscopy, ¹³C nuclear magnetic resonance spectroscopy, scanning electron microscopy and thermogravimetric analysis. The point of zero charge (pH_pzc) of the modified cryogels was found to be 7.13 and RBB removing capabilities of PEI-modified PAAm cryogels were investigated at pH between 2 and 7. In addition, the adsorption treatments were performed at different process time, incubation temperature, initial dye concentration and adsorbent amount to find maximum removal capacity of the adsorbent. The modified cryogels adsorbed maximum amount of RBB at pH 2 and the sorption process reached equilibrium in 6 h. It was observed that the adsorption efficiency did not change much with the increase in temperature. The maximum RBB removal capacity of the modified cyrogels was determined to be 201 mg/g when the initial RBB concentration was 200 mg/L, treatment time was 6 h at pH 2. Moreover, the adsorption of RBB dye with the modified cryogels takes place with a second order kinetic and RBB dye adsorption data showed compliance with the Langmuir isotherm. The findings of the study expose that the obtained PEI-modified PAAm cryogels are a hopeful material for RBB removal in aqueous environment.

     

Activated carbon from Ceiba pentandra hulls, an agricultural waste, as an adsorbent in the removal of lead and zinc from aqueous solutions

The ability of low-cost activated carbon prepared from Ceiba pentandra hulls, an agricultural waste material, for the removal of lead and zinc from aqueous solutions has been investigated. In the batch tests experimental parameters were studied, including solution pH, contact time, adsorbent dose and initial metal ions concentration. The adsorbent exhibited good sorption potential at pH 6.0. Maximum removal of lead (99.5%) and of zinc (99.1%) with 10 g/l of sorbent was observed at 50 mg/L sorbate concentration. Removals of about 60-70% occurred in 10 min, and equilibrium was attained at around 50 min for both metals. The functional groups (CO, SO,-OH) present on the carbon surface were responsible for the adsorption of metal ions. The adsorption parameters were analysed using both the Freundlich and Langmuir models. The data are better fitted by the Freundlich isotherm as compared to Langmuir model, and the adsorption capacities for lead and zinc were 25.5 and 24.1 mg/g, respectively. Kinetics of adsorption obeyed a second order rate equation and the rate constant was found to be 2.71 x 10(-2) and 2.08 x 10(-2) g/mg/min for lead and zinc, respectively. The desorption studies were carried out using dilute HCl, and the effect of HCl concentration on desorption was studied. Maximum desorptions of 85% for lead and 78% for zinc were attained with 0.15 M HCl.     

高炉渣对Cd~(2+)的吸附性能

采用包头钢铁集团炼铁厂的高炉渣为吸附剂(粒径0.154 nm)对Cd2+进行吸附,运用SEM技术对吸附剂进行了表征,研究了初始Cd2+质量浓度、吸附剂加入量、吸附时间、吸附温度和废水pH对Cd2+去除率的影响,并探讨了吸附机理。表征结果显示:高炉渣吸附剂具有疏松多孔的特点,表面十分粗糙,比表面积较大。实验结果表明:当吸附温度为室温(28℃)、废水pH为7、初始Cd2+质量浓度为10 mg/L、吸附剂加入量为8 g/L、吸附时间为60 min时,Cd2+去除率达到98.55%;高炉渣对Cd2+的吸附符合拟二级动力学方程和Langmuir等温吸附模型,且吸附反应易发生。     

纳米MnO_2/Fe_3O_4对镉离子的静态吸附

采用水热合成法将Mn O_2包覆于纳米Fe_3O_4的表面,制备出纳米Mn O_2/Fe_3O_4,并将其用于含镉溶液的吸附。考察了吸附效果的影响因素,并研究了纳米Mn O_2/Fe_3O_4的重复使用性能。实验结果表明:在初始镉离子质量浓度为10 mg/L、吸附剂投加量为4 g/L、吸附温度为20℃、溶液p H为6.0、吸附时间为12 h的条件下,镉离子去除率由使用纳米Fe_3O_4时的3%增至使用纳米Mn O_2/Fe_3O_4时的96%;在初始镉离子质量浓度为50 mg/L、纳米Mn O_2/Fe_3O_4投加量为4 g/L、吸附温度为20℃、溶液p H为6.0、吸附时间为1 h的条件下,镉离子去除率达78%,吸附量为9.7 mg/g;经5次重复使用后,纳米Mn O_2/Fe_3O_4对镉离子的去除率仅比首次使用时降低了10百分点,具有良好的重复使用性能。     

氧化石墨烯负载纳米零价铁的制备及其对亚甲基蓝的吸附

采用液相还原法制备氧化石墨烯负载纳米零价铁吸附剂(Fe0/GO),并用于吸附去除溶液中的亚甲基蓝(MB)。考察了溶液p H、吸附温度、吸附时间、初始MB质量浓度对Fe0/GO吸附MB的影响。SEM等表征结果显示:Fe0以球形或短链形负载在GO上,增加了材料的反应活性位点;Fe0/GO的比表面积为158.32 m2/g,等电点为3。实验结果表明:在溶液p H为6、吸附时间5 h、吸附温度25℃的最佳条件下,加入400 mg/L的Fe0/GO,处理初始MB质量浓度为160 mg/L的MB溶液,MB去除率为89.26%,吸附量为125.5 mg/g;Langmuir等温吸附方程和Frenudlich等温吸附方程均能较好地描述Fe0/GO对MB的吸附过程;Fe0/GO对MB的吸附行为遵循准二级动力学方程;计算得出吸附温度为25℃、初始MB质量浓度为160 mg/L时的饱和吸附量为201.2 mg/g,平衡吸附量为124.3 mg/g。     

含油浮渣制备含碳吸附剂并用于含油污水的处理

以含油浮渣为原料制备含碳吸附剂,并用于含油污水的处理。用比表面分析仪和SEM技术对吸附剂进行表征。通过正交实验和单因素实验考察吸附剂加入量、吸附时间及温度、污水pH对污水处理效果的影响。表征结果显示,含碳吸附剂碳元素含量高达90%(w)以上,表面粗糙,孔径分布以中孔为主,比表面积477.5 m2/g,碘吸附值376.48 mg/g。实验结果表明:在吸附温度30℃及时间60 min、含碳吸附剂加入量20 g/L、污水pH为7的最佳实验条件下,处理初始COD为502.12 mg/L、石油类质量浓度45.31 mg/L.的含油污水,COD和石油类的去除率分别为91.51%和87.1%,处理后的COD和石油类质量浓度分别为42.62 mg/L和5.83 mg/1,达到GB 8978—1996《污水综合排放标准》中的二级排放标准;含碳吸附剂的污水处理效果优于术质活性炭。     

水力空化-O3氧化联合超声吸附处理煤气化废水

采用水力空化-O₃氧化与超声吸附法联合处理煤气化废水。吸附剂以钙基膨润土为原料,经十六烷基三甲基溴化铵改性制得。通过单因素实验分别探讨了水力空化-O₃氧化与超声吸附的适宜处理条件,并在该条件下对废水进行联合处理。实验结果表明：在O₃通量194.4 mg/L、空化时间60 min、入口压力0.4 MPa、废水pH 10.00的优化条件下,水力空化-O₃氧化对COD和苯酚的去除率分别达67.3%和57.5%;在此基础上进一步采用超声吸附法处理废水,在吸附剂投加量0.06 g/mL、超声时间60 min、废水pH 4.00、吸附温度25 ℃的优化条件下,处理后出水中COD和苯酚质量浓度分别降至317.1 mg/L和117.9 mg/L;COD和苯酚的总去除率分别达97.9%和96.6%。     

Uptake of dyes by a promising locally available agricultural solid waste: coir pith

The adsorption of rhodamine-B and acid violet by coir pith carbon was carried out by varying the parameters such as agitation time, dye concentration, adsorbent dose and pH. The adsorption followed both Langmuir and Freundlich isotherms. The adsorption capacity was found to be 2.56 mg and 8.06 mg dye per g of the adsorbent for rhodamine-B and acid violet, respectively. Adsorption of dyes followed first order rate kinetics. Acidic pH was favorable for the adsorption of acid violet and alkaline pH was favorable to rhodamine-B. Desorption studies showed that alkaline pH was favorable for the desorption of acid violet and acidic pH was favorable for the desorption of rhodamine-B.     

水性油墨废水絮凝污泥制备吸附剂及阳离子染料的吸附

以水性油墨废水絮凝污泥为原料、采用一步炭化活化法制备了吸附剂,并将其用于阳离子蓝X-GRRL溶液(300 mg/L)的吸附处理。考察了吸附剂投加量、吸附时间、吸附温度和吸附pH对吸附效果的影响,并对吸附动力学进行了探讨。结果表明:所制得吸附剂的总孔体积为0.5 cm~3/g,平均孔径为7.12 nm;在吸附剂投加量0.6g/L、吸附时间420 min、吸附温度25℃、吸附pH 5.4的条件下,吸附量高达486.21 mg/g,脱色率达97.24%;该吸附剂对于阳离子蓝X-GRRL的吸附过程可用准二级动力学模型和颗粒内扩散效应模型很好地描述。     

改性核桃壳对Cr(Ⅵ)的吸附

采用甲醛-硫酸改性法制备改性核桃壳吸附剂,利用静态吸附法研究了改性核桃壳对模拟废水中低浓度Cr(Ⅵ)的吸附性能,并采用SEM和FTIR技术对改性前后的核桃壳进行表征。表征结果显示,改性后的核桃壳表面更粗糙,孔隙轮廓更清晰,更有利于对Cr(Ⅵ)的吸附。实验结果表明:在初始Cr(Ⅵ)质量浓度为20 mg/L、初始废水p H为1、吸附温度为30℃、吸附时间为100 min、改性核桃壳加入量为24 g/L的条件下,改性核桃壳对Cr(Ⅵ)的去除率为98.4%,高于在相同条件下未改性核桃壳对Cr(Ⅵ)的去除率(93.1%);改性核桃壳对Cr(Ⅵ)的吸附更符合Freundlich等温吸附方程,对Cr(Ⅵ)的吸附行为满足拟二级动力学方程。     

凹凸棒土/苯胺-邻氨基酚复合吸附剂的制备及其对Cr(Ⅵ)的吸附性能

采用原位聚合法制备了凹凸棒土/苯胺-邻氨基酚（ATP/PANOAP）复合吸附剂,对其进行了SEM和FTIR表征,并通过吸附实验考察了ATP/PANOAP对水中Cr（Ⅵ）的吸附性能。实验结果表明,ATP/PANOAP对水中Cr（Ⅵ）具有良好的去除效果,在Cr（Ⅵ）初始质量浓度为50 mg/L、溶液pH为6、吸附剂加入量为0.375 g/L、温度为298 K的条件下,Cr（Ⅵ）去除率达93.39%。ATP/PANOAP对Cr（Ⅵ）的吸附动力学过程符合准二级动力学模型,吸附热力学过程符合Langmuir单层吸附模型,该吸附过程以化学吸附为主,且为自发进行的吸热反应。     

硝酸铈改性赤泥制备除磷吸附剂

用六水硝酸铈改性赤泥并处理含磷废水.实验结果表明:当硝酸铈质量分数为0.45％、焙烧温度为500℃时,制备的吸附剂的吸附性能最好;用该吸附剂处理含磷废水,当初始废水pH为3、振荡时间为80 min时,废水TP去除率约为95％,废水中磷质量浓度为0.41 mg/L,达到GBI8918-2002《城镇污水处理厂污染物排放标准》中的一级标准.该吸附剂的吸附过程符合Langmuir吸附模型.     

加拿大一枝黄花纤维素的改性及其对Cr(Ⅵ)的吸附

采用环氧氯丙烷和三甲胺对加拿大一枝黄花纤维素进行改性,改性后的加拿大一枝黄花纤维素对Cr(Ⅵ)具有一定的吸附作用.在改性加拿大一枝黄花纤维素加入量为3.2 g/L、吸附温度为40℃、吸附时间为240 min、溶液pH为2的条件下,对初始Cr(Ⅵ)质量浓度为20 mg/L的K2Cr2O7溶液进行吸附实验,Cr(Ⅵ)吸附量可达5.69 mg/g,Cr(Ⅵ)去除率为91％.动力学研究结果表明,改性加拿大一枝黄花纤维素对Cr(Ⅵ)的吸附以液膜扩散为控制步骤,反应过程符合Boyd液膜扩散方程,相关系数达到0.995 47.     

玉米秸秆生物炭对苯胺的吸附

以玉米秸秆为原料制备生物炭吸附剂,研究了生物炭对水中苯胺的吸附性能。表征结果显示:制备的生物炭的比表面积为449.7 m2/g,体积平均粒径为103μm,主要以小粒径存在;制备的生物炭表面以碱性含氧官能团为主,含量为1.31 mmol/g。实验结果表明:在溶液p H 3、生物炭加入量10 g/L、吸附温度313 K、吸附时间3.0h的最佳反应条件下处理初始苯胺质量浓度为400 mg/L的苯胺溶液,苯胺去除率为94.0%,吸附量为37 mg/g;生物炭对苯胺的吸附过程符合拟二级动力学方程,吸附等温线满足Freundlich等温吸附方程;生物炭对苯胺的吸附是自发、吸热的过程;吸附过程中存在着水分子从生物炭表面的解吸。