MBR-RO组合工艺污水回收中试研究

以A2/O-MBR为预处理工艺,构建了MBR-RO组合系统并用于城市污水的直接处理与回收,考察了MBR工艺作为RO预处理的可行性,评价了RO膜的出水水质,分析了不同操作条件对RO膜的渗透性能及膜污染的影响.研究表明,RO出水平均值为TOC＜1.3 mg/L、NH 4-N＜0.03 mg/L、TN＜0.1 mg/L,TP未检出,电导率和浊度分别小于30μS/cm和0.12 NTU,MBR出水中的无机离子已被RO完全截留,MBR-RO系统具有很高的污染物降解能力和脱盐能力,其出水水质可达饮用水水质标准.MBR作为RO的预处理是完全可行的,连续6个多月的运行中RO膜污染表现不严重.     

预臭氧化对二级出水微滤过程中膜有机物污染的影响

在二级出水溶解性有机物（secondary effluent organic matter,EfOM）的微滤过程中,多种因素均与膜的有机污染相关,比如总有机物的含量,溶解性有机物的亲疏水性组成等.本文主要研究了在二级出水微滤过程中溶解性有机物的膜污染,以及预臭氧化对二级出水溶解性有机物性质的影响进而对膜有机污染的影响....     

磁场强化絮凝减缓膜污染的影响因素分析

研究磁场及磁致效应对磁强化絮凝膜过滤工艺(Magnetic enhanced flocculation membrane filtration,MEFMF)处理地表水中膜污染的影响;运用Design-Expert7.0软件进行试验设计,考察了磁化时间、混凝剂浓度和磁粉浓度对磁强化絮凝膜过滤工艺中膜污染变化的影响,结果表明磁化时间、混凝剂浓度以及两者的协同作用是影响磁强化絮凝膜过滤工艺中膜污染的主要因素.磁化时间和混凝剂浓度的协同作用影响着磁絮体的粒径和膜表面滤饼层形态,磁絮凝工艺形成的絮体粒径大且分型维数高,减弱了膜孔堵塞,减缓了膜污染.磁强化絮凝减缓膜污染最佳试验条件是磁化时间为6 min,Fe3O4浓度为8 mg·L-1,FeCl3浓度为44 mg·L-1.     

碳纳米管改性PVDF中空纤维超滤膜处理二级出水抗污染性能研究

采用碳纳米管改性PVDF中空纤维超滤膜以缓解膜污染.考察了CNTs的乙醇分散液浓度、CNTs尺寸和负载量对改性中空纤维膜的抗污染性能和改性膜内表面CNTs层稳定性的影响,分析了该改性膜对二级出水DOC、UV254的去除效果,并对改性膜出水的荧光特性进行了表征.结果表明,选用体积分数为50%的乙醇分散液、外径为30~50 nm碳纳米管、负载量为3 g·m-2时,制备的改性中空纤维膜CNTs层稳定,抗污染能力显著提高.与未改性膜相比,改性膜对二级出水DOC和UV254的去除率分别提高了37%和56%;且对二级出水中的腐殖类和蛋白质类物质去除能力明显增强.     

城市污水二级出水超滤膜污染与膜特性的研究

以城市污水二级出水为过滤介质,考察了PVA、PVP、PMMA等与PVDF的二元及三元共混超滤膜的过滤污染行为.结果表明,共混优化了PVDF超滤膜的结构参数,添加剂PVP、PVA可有效改善膜的亲水化程度,提高膜渗透通量.超滤膜的亲水性和结构特性对膜抗污染性能影响较大;堵孔阻力是二级出水过滤膜污染不可逆的主要原因.亲水性较强的超滤膜,二级出水过滤初期易因浓差极化而导致滤饼层污染,造成一定的通量衰减,但易清洗恢复,不可逆污染指数(rir)为0,抗污染性能好.致密的超滤膜表面有利于防止二级出水中的中低分子量污染物进入膜内部,而断面通透大孔和疏松海绵层结构的超滤膜,能减少二级出水中的污染物在膜中沉积形成堵孔阻力.膜表面多孔,内部大孔发育不充分,易形成堵孔污染,通量衰减大且不易清洗恢复,膜污染不可逆.     

不同pH值下腐殖酸反渗透膜污染中的界面相互作用解析

应用extended derjaguin-landau-verwey-overbeek (扩展DLVO) 理论评价不同pH值下范德华力、静电力、疏水性力3种界面相互作用对腐殖酸反渗透(reverse osmosis, RO)膜污染的贡献,探究pH值影响腐殖酸RO膜污染的主控机制.对3种常规RO膜的理论分析结果表明,静电力对腐殖酸RO膜污染的贡献很小,范德华力使膜污染加剧;疏水性力会减缓膜污染.与前期粘附阶段相比,后期粘聚阶段中范德华力的贡献有所增大,疏水性力在2个污染阶段中均起主导作用.膜污染随pH值的降低而加重,疏水性力作用能的改变是pH值影响系统界面自由能的主控机制.相应pH值下3种RO膜过滤实验数据及其相关性分析结果表明,扩展DLVO理论能定量评价3种界面相互作用的贡献,界面自由能和膜污染之间有很好的相关关系,RO膜纯水接触角的数值不宜作为评价膜污染的指标.     

二级出水水质对中试臭氧-微滤工艺运行的影响

在以膜微滤为主的组合工艺对二级出水的处理过程中,二级出水水质可能对于微滤过程中膜污染的发展有较强影响.为此考察了2座污水处理厂及1个中试处理设施的二级出水水质,包括常规水质指标、水中颗粒物粒径分布及树脂吸附分离后不同有机物部分的荧光光谱所表征的有机物组分等对于死端微滤中TMP发展变化的影响.研究结果表明:①颗粒物浓度和颗粒物粒径分布对于微滤过程中的可逆污染有较大贡献;②二级出水中的有机物,尤其是其中的腐殖质部分,对于微滤过程中的不可逆污染有较大贡献.     

集成膜分离法在城市污水深度处理中应用的研究

以城市生活污水处理厂二级生化出水作为膜分离系统的进水,分别采取"237NF+RO","A195NF+RO"和"N236NF+RO"等3种集成膜分离法深度处理该污水,从中优选出1种工艺深入考察各单元膜的运行工况.结果表明:237NF纳滤阶段的最佳膜运行参数为:膜进口压力为0.5 MPa,水回收率为10%,膜运行温度为30℃,原料浓缩倍数为8～10倍;RO反渗透阶段的最佳膜运行参数为:膜进口压力1～1.3 MPa,水回收率7%,膜运行温度30℃,原料浓缩倍数10倍.在各自最佳运行工况下的最终RO膜渗透液的水质符合<城市污水再生利用>系列标准.     

煤化工废水反渗透处理系统的运行效果及膜污染分析

针对煤化工废水反渗透（RO）膜处理系统夏季严重污堵的问题,本研究以实际某煤化工污水处理厂一级两段式RO系统为考察对象,分析了系统运行效能及膜污染特征.研究发现,生化段稳定地实现了有机物的削减,离子交换树脂进一步保障了产水的脱盐率,促进实现高水回收率,是煤化工废水零排放的重要保障.但对膜系统而言,脱盐及有机物去除的主要负荷集中在RO过程,一段/二段RO脱盐率分别为94.16%和96.16%,COD去除率分别为68.12%和87.4%;相对进水,一段RO有机物浓缩了9倍,二段RO盐浓缩了5倍.因此,两段膜过程都出现显著的膜污染,一段RO以有机-微生物-硅污染为主,形成致密的污染层,由进口到出口逐渐增厚,主要为蛋白质、多糖、腐殖酸;二段RO以Ca、Mg等的无机结垢为主,污染层结构相对松散,由进口到出口片状结晶逐渐增大.因此,预处理工艺的稳定运行及对污染物的去除以减轻RO过程的污染负荷是膜污染控制的关键;同时,针对RO系统中膜污染分布特征,制定杀菌、阻垢和化学清洗等膜污染控制策略以防止形成微生物抗性及"清洗剂抗性"具有重要意义.     

印染废水反渗透脱盐系统运行性能及膜污堵特性

反渗透(RO)脱盐工艺对实现印染废水再生利用具有重要的意义.膜污堵却制约了RO工艺应用.对广东省某工业园区印染废水RO脱盐系统运行性能及膜污堵特性进行了研究.结果表明,印染废水生化处理出水经臭氧氧化-砂滤-超滤(UF)预处理后,RO进水COD平均浓度为12.4 mg·L~(-1),浊度1 NTU.RO系统脱盐率稳定在98%,RO产水高锰酸盐指数约为0.7 mg·L~(-1),浊度约为0.12 NTU.但RO系统运行3 a后,跨膜压差高达0.6 MPa,产水量下降至120 m~3·h~(-1),且不能通过化学清洗恢复,在RO膜面沉积了不可逆的污堵物.RO膜面的有机物占总污堵物干重的(53.5±0.2)%,无机物占(46.5±0.2)%,RO膜面有机污堵与无机污堵贡献相近.Si、Al与Ca是RO膜面主要的无机元素.碱液(Na OH溶液)对沉积在RO膜面的Si与Al及有机物提取效果较好.     

Optimisation of chemical purification conditions for direct application of solid metal salt coagulants: Treatment of peatland-derived diffuse runoff

The drainage of peatland areas for peat extraction,agriculture or bioenergy requires affordable,simple and reliable treatment methods that can purify waters rich in particulates and dissolved organic carbon.This work focused on the optimisation of chemical purification process for the direct dosage of solid metal salt coagulants.It investigated process requirements of solid coagulants and the influence of water quality,temperature and process parameters on their performance.This is the first attempt to provide information on specific process requirements of solid coagulants.Three solid inorganic coagulants were evaluated:aluminium sulphate,ferric sulphate and ferric aluminium sulphate.Pre-dissolved aluminium and ferric sulphate were also tested with the objective of identifying the effects of in-line coagulant dissolution on purification performance.It was determined that the pre-dissolution of the coagulants had a significant effect on coagulant performance and process requirements.Highest purification levels achieved by solid coagulants,even at 30% higher dosages,were generally lower(5%-30%) than those achieved by pre-dissolved coagulants.Furthermore,the mixing requirements of coagulants pre-dissolved prior to addition differed substantially from those of solid coagulants.The pH of the water samples being purified had a major influence on coagulant dosage and purification efficiency.Ferric sulphate(70 mg/L) was found to be the best performing solid coagulant achieving the following load removals:suspended solids(59%-88%),total organic carbon(56%-62%),total phosphorus(87%-90%),phosphate phosphorus(85%-92%) and total nitrogen(33%-44%).The results show that the use of solid coagulants is a viable option for the treatment of peatland-derived runoff water if solid coagulant-specific process requirements,such as mixing and settling time,are considered.     

柠檬酸对不同混凝剂混凝效果的影响

通过对不同混凝剂(Al2(SO4)3、Fe2(SO4)3、PACl25)混凝过程中絮体粒径大小的测定,研究了在不同pH条件下柠檬酸浓度对3种混凝剂混凝效果的影响.结果发现,随着柠檬酸浓度的增加,3种混凝剂混凝过程中生成絮体的速率和粒径大小都在逐渐降低,但3种混凝剂受到抑制的程度不同:对于硫酸铝,当n(柠檬酸)/n(Al) =0.1时,混凝20 min内没有絮体生成;对于硫酸铁,仅当n(柠檬酸)/n(Fe)=0.05时,絮体就不再生成;而当n(柠檬酸)/n(Al) =0.5时,PACl25絮体仍能很快地形成.不同的pH值下柠檬酸对混凝效果的抑制程度也不同:对于硫酸铝,pH =6时生成絮体最大,pH =8时没有絮体生成;对于硫酸铁,pH =5时产生絮体的情况和pH =6时相似,而pH =7时絮体消失;而对于PACl25,絮体大小随着pH值的升高而增大(pH在7～9之间).另外,通过对Zeta电位的测定可知,随着柠檬酸浓度的增加,3种混凝剂的Zeta电位都在降低,但降低的速率不同:硫酸铁＞硫酸铝＞ PACl25,这与絮体粒径大小的变化规律一致.     

聚合氯化铝及聚合氯化铝铁处理微污染地表水效果

选用两种无机高分子混凝剂聚合氯化铝(PAC)和聚合氯化铝铁(PAFC),与传统混凝剂Al2(SO4)3处理微污染地表水。以浊度和CODMn去除率为主要指标,考察投药量和pH对混凝效果的影响。通过考察沉淀时间对浊度去除效果的影响,结合实验现象,讨论三种混凝剂生成矾花的大小和沉降性能。结果发现,PAC和PAFC在5mg/L的投药量下可以取得较好的混凝效果,出水符合GB 5749-2006《生活饮用水卫生标准》。三种混凝剂的最佳pH为6,PAFC受pH影响较小,当pH为5～8时可取得较好的CODMn去除效果。PAFC生成的矾花体积较大,沉降性能较好,在实际应用中可缩短沉淀池的水力停留时间。     

Assessment of fieldscale zero liquid discharge treatment systems for recovery of water and salt from textile effluents

Treatment systems consisting of physico-chemical treatment, biological treatment, ozonation, reverse osmosis system, nanofiltration system, multiple effect evaporator, crystalliser and solar evaporation pans set up by three dyeing units in Tirupur, India, were assessed in the present study. The composite samples were analysed for colour, pH, TSS, TDS, chlorides, sulphates, COD, total iron, silica, SDI, LSI and total hardness. The results indicated that the physico-chemical treatment alone is inadequate to achieve the feed water quality norms for spiral wound RO membranes. It is recommended that the primary treatment may incorporate biological treatment and ultrafiltration to reduce COD and SDI in the feed water. Water recovery by reverse osmosis and salt recovery using nanofilter were 87% and 71%, respectively.It was also found that there is substantial direct profit in recovering water using reverse osmosis and sodium chloride in solution using nanofiltration as compared to the recovery of Na₂SO₄. The study also revealed that high quality water could be produced by treatment system incorporating membrane technology at affordable costs and recycled back into the process in the textile dyeing industry.     

混凝-吸附处理黄河水及对氯消毒中氯衰减的影响

选用2种无机高分子混凝剂聚合氯化铁(PFC)和聚合氯化铝(PAC)处理黄河水,考察了混凝剂的投加量对浊度、UV254、DOC和高锰酸盐指数的去除效果,并结合混凝出水的Zeta电位分析其混凝机制.选择粉末活性炭与混凝联用,研究了混凝剂和吸附剂投加量以及二者的投加顺序对有机物去除效果的影响,并对混凝吸附后出水进行加氯消毒,考察水中残余氯随时间的变化.结果表明,2种混凝剂均有较高的浊度去除率(﹥90%).PAC对UV254、高锰酸盐指数和DOC的去除率分别为29.2%、26.1%和27.9%;PFC对三者的去除率分别为32.3%、23.3%和32.9%.PAC在混凝过程中,电中和作用占主导地位;PFC在混凝过程中,吸附架桥和电中和同时发挥作用.混凝-吸附联用处理黄河水样时,有机物的去除率随混凝剂和吸附剂投加量的增加而升高.先混凝后吸附工艺对UV254和DOC的去除效果优于先吸附后混凝工艺.先使用PAC混凝后吸附对UV254和DOC的去除率分别为95.2%和99.9%;对于PFC,先混凝后吸附对UV254和DOC的去除率分别为90.1%和99.9%.但是先投加粉末活性炭能提高矾花的沉降性能,且处理出水在保持持续消毒效果方面优于前者.     

生活污水混凝处理试验研究

通过混凝实验,比较了明矾、碱式氯化铝、聚合铝、聚铁以及硫酸铁5种混凝剂强化处理生活污水的效果,并分析了pH对COD、总磷去除率的影响。铝系混凝剂处理效果好于铁系混凝剂。     

不同混凝剂对流溪河水源水中藻类去除的对比

对夏秋季节广州流溪河下游含藻水源水进行了混凝沉淀试验处理,研究了硫酸铝、聚合氯化铝、聚合氯化铝铁、聚合硫酸铁等不同混凝剂及其投加量对藻类和浊度的去除效果,考察了pH值、温度对不同混凝剂去浊率和除藻率的影响,并用zeta电位及显微拍照分析方法,分别对混凝剂的静电中和能力与絮凝体的形态结构进行了初步的研究表征.结果表明,对于pH值为6~8、水温315℃、藻类和浊度分别为 1.14×107~4.10×107个/L和27~38NTU的水源水,硫酸铝的混凝效果最好,当其投加量为3.0mg/L时,其除藻率和去浊率可分别达到80%和89%,其他混凝剂混凝效果的优劣顺序依次为:聚合氯化铝铁、聚合硫酸铝、聚合硫酸铁;而对冬季的低温水源水,采用聚合硫酸铝或聚合氯化铝铁时,除藻和去浊效果较好.     

复合型混凝剂处理印染废水的研究

在分析混凝机理和各种混凝剂特性的基础上,用新型复合型混凝剂Ⅰ型和Ⅱ型对印染废水处理进行了实验研究。一次混凝投药量为300mg/L 时,Ⅰ型和Ⅱ型对COD 去除率分别为70. 1%、80. 8%,色度去除率分别为84. 0%、99.2%。再经生物法处理,效果更好。     

Application of a green coagulant with PACl in efficient purification of turbid water and its mechanism study

The applications of natural polymeric flocculants due to their green feature has been recently received much more attention. In this work, the combined usages of a cationic starch-based coagulant and polyaluminum chloride (PACl) were extensively evaluated for various addition sequences in the coagulation of both raw (surface water from the Jiuxiang River) and synthetic turbid water (two kaolin suspensions with different initial turbidities). Two typical cationic starch-based coagulants with different structures (St-G and St-E) were tried. In comparison to St-G, St-E and PACl used individually as well as St-G and St-E dosed after PACl, the combination of the starch-based coagulants fed before PACl showed higher turbidity removal efficiency, which featured not only less optimal doses of both inorganic and organic coagulants but also lower residual turbidity. On the basis of a detailed analysis of the particle size and its distribution in solution supernatants before and after coagulation by two starch-based coagulants and PACl, polymeric coagulants preferentially coagulate the small-sized colloids due to their distinct long-chain structures, but PACl preferentially coagulates the medium-sized ones. Thus, the medium-sized particles that were previously formed by the starch-based coagulants would be collectively and effectively removed by the subsequent addition of PACl. The addition sequence of the inorganic and organic coagulants in their combined usage is an important factor for improvement of the turbidity removal efficiency in practice.     

混凝法处理除尘废水的研究

采用混凝的方法处理燃煤锅炉湿式除尘废水 ,取得了良好的效果。通过加入各种混凝剂 ,测定有关指标 ,确定最佳的混凝剂及其最佳的投加量和pH值。实验表明 ,采用CPAM的效果最好 ,在pH =7时 ,每t水的加药量只需 0 .1 5g。处理后的水不仅达标 ,而且可回用 ,节约了大量的水资源。