共查询到20条相似文献,搜索用时 62 毫秒
1.
新型复合球填料为沸石与悬浮球填料的有机组合体,密度约为0.92~0.97g/cm3,比表面积为711~1185m2/m3,表面粗糙,物化性能稳定.在曝气量为20∶1,停留时间为6 h时,装有新型复合球填料的反应柱挂膜容易,成膜时间短,膜不易脱落,且生物相丰富.膜成熟时对生活污水中的氨氮和COD都有很好的去除效果,出水氨氮浓度≤2 mg/L,去除率≥93%;出水COD浓度≤22 mg/L,去除率≥80%.新型复合球反应柱在稳定状态处理低浓度的二级出水时,出水氨氮浓度≤2 mg/L,去除率≥89%,出水COD浓度为10~36 mg/L,去除率为48%~81%.出水水质符合GB50335-2002标准. 相似文献
2.
一体式膜生物反应器处理生活污水的中试研究 总被引:1,自引:0,他引:1
采用中试规模(1.8m^3/d)的缺氧-好氧膜生物反应器(A/OMBR)对城市污水处理回用进行了试验研究。试验结果表明,该工艺处理效果优良,系统对COD、氨氮、浊度、总氮、总磷去除率较高,COD、氨氮出水浓度分别为7~39 mg/L、0~1.31mg/L。出水水质优于城市杂用水水质标准(GB/T18920-2002)。 相似文献
3.
4.
两级UASB与好氧组合工艺处理城市生活垃圾渗滤液的启动研究 总被引:1,自引:0,他引:1
采用两级UASB与好氧组合工艺处理早期城市生活垃圾渗滤液。系统出水按不同比例回流到一级UASB中进行反硝化,同时进行产甲烷反应,有机物在二级UASB中被进一步降解,好氧池完成剩余有机物的去除和氨氮的硝化。启动阶段通过对原渗滤液不同比例的稀释,分5次逐步提高进水浓度,启动结束时完成了对原渗滤液的高效处理。在进水COD浓度从3000mg/L提高到15000mg/L,氨氮浓度从250mg/L提高到1400mg/L时,最终COD去除率稳定在92%左右,氨氮去除率可达99%以上,一级UASB中反硝化率接近100%,回流比为300%时系统总氮去除率为70%~80%。 相似文献
5.
6.
钱伯兔 《环境污染治理技术与设备》2005,6(6):66-68
采用沉淀-SBR-活性炭过滤复合工艺对城市垃圾渗滤液进行处理,确定混凝、SBR和活性炭过滤的最隹参数。结果表明,当进水COD为2500mg/L、氨氮在900mg/L的条件下,经该系统处理后,出水COD均在300mg/L以下,氨氮在20mg/L以下,COD去除率达90%以上,氨氮去除率达98%以上,达到较好的去除有机物和去氨效果。 相似文献
7.
同步硝化反硝化生物脱氮技术研究 总被引:5,自引:0,他引:5
讨论了影响同步硝化反硝化反应的各参数,并进行了单因素实验与正交实验,获得了同步硝化反硝化生物脱氮工艺运行的最佳条件:DO浓度控制在0.5~2mg/L,COD浓度为600~800mg/L,混合液悬浮固体(MLSS)为5000mg/L,pH值在8.0左右,反应时间为6h。在此条件下,氨氮及COD的去除率都较高,分别达85%和95%,总氮去除率为68.5%。 相似文献
8.
SBR法处理垃圾填埋场新鲜渗滤液的实验研究 总被引:6,自引:0,他引:6
采用SBR渐减曝气工艺处理模拟城市生活垃圾填埋场新鲜渗滤液,实验研究了反应器运行条件与出水水质的关系及有机碳的转移规律。研究结果表明:新鲜渗滤液经24h曝气处理后,出水COD浓度约为500mg/L,BOD5/COD降为0.14左右;出水COD浓度与容积负荷无明显相关性;COD去除率与容积负荷呈正比,并在容积负荷为5.0kg COD/m^3·d时达到最高,约95%;去除的有机碳气相转化率与容积负荷呈正比,在容积负荷为5.0kg COD/m^3·d时,有机碳气相转化率接近100%;该系统最高容积负荷为5.0kg COD/m^3d,相应的污泥浓度(以混合液悬浮性挥发固体(MLVSS)计)为7.12g/L。 相似文献
9.
悬浮填料生物膜床反应器处理高校生活污水 总被引:5,自引:0,他引:5
本研究利用悬浮填料生物膜床反应器处理高校生活污水,对CODCr氨氮和总磷有较好的去除效果。水力停留时间6h时,CODCr总去除率最高可达到95%,出水CODCr稳定在30mg/L以下;总磷去除率达到50%以上,出水总磷含量低于0.5mg/L;对NH3-N的去除率可以稳定在80%以上,出水NH3-N低于1mg/L。 相似文献
10.
UASB反应器处理生活污水的试验研究 总被引:1,自引:0,他引:1
采用UASB中试(100m^3/d)对生活污水处理进行了研究。试验结果表明,采用此系统处理生活污水,出水水质良好。COD的去除率在52%-83%,出水的COD值〈100mg/L以下,SS的去除率在95%左右,UASB处理生活污水的最佳停留时间为6h。产气率在0.1m^3/d。不管停留时间在10h、5h,出水的氨氮、乙酸值比进水的高;钙、镁、总氮、总磷、硫酸根和硝酸根离子出水值比进水值低。 相似文献
11.
造纸废水混凝处理中SFT助凝替代性研究 总被引:1,自引:0,他引:1
中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染 相似文献
12.
Janusz A. Pudykiewicz Anna S. Koziol 《Atmospheric environment (Oxford, England : 1994)》1998,32(24):5541
The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing. 相似文献
13.
Árpád Ambrus 《Journal of environmental science and health. Part. B》2013,48(3):435-442
Abstract A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits. 相似文献
14.
介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠 相似文献
15.
活性炭三维电极法对印染废水的处理研究 总被引:4,自引:0,他引:4
对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25~30 V,进水pH值6.5~7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。 相似文献
16.
不同泥源对厌氧氨氧化反应器启动的影响 总被引:2,自引:1,他引:1
采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。 相似文献
17.
18.
以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径<1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径. 相似文献
19.
Volker Berding Stefan Schwartz Michael Matthies 《Environmental science and pollution research international》1999,6(1):37-43
The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters
(inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation,
on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency.
The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity
was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters),
and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity
to 961, and the maximal dimension is 21. 相似文献