Performance evaluation of an in situ nitrous acid measurement system and continuous measurement of nitrous acid in an indoor environment

Nitrous acid (HONO) may cause adverse effects to mucous membranes and lung function when people are exposed to higher HONO concentrations than those present in typical indoor residential environments. Therefore, determination of HONO concentration in indoor environments is required to investigate occurrences of high HONO levels. In this work, a high-time-resolution measurement system was utilized to better understand the levels and dynamic behavior of HONO in an indoor environment. The performance of the in situ HONO analyzer applied to this work was evaluated using a 12-hr integrated annular denuder technique under ambient conditions. Both methods for the measurements of HONO were in good agreement, with a regression slope of 0.84, an intercept of 0.09, and correlation coefficient (r2) of 0.67. Indoor HONO and nitrogen oxide concentrations were also observed for approximately 5 days in winter in the living room of an apartment that had a gas range for cooking in the kitchen. Investigation of the relationships among nitric oxide (NO), nitrite (NO2), and HONO concentrations suggests that HONO production during combustion could be the result of direct emission, whereas the heterogeneous NO2 chemistry during the background period and after combustion was the possible pathway of HONO production. Controlled combustion experiments, performed at a burning rate of 50% valve setting, show peak HONO concentrations during the unvented combustion to be approximately 8-10 times higher than background levels depending on the time of day. At a burning rate setting of 50%, the peak concentration of HONO during unvented combustion was found to be 33-37% higher than those from "weak" (airflow = 340 m3/hr) and "strong" (airflow = 540 m3/hr) vented combustions. The decay rate of the HONO concentrations for the unvented combustion conditions was approximately 2-fold higher in the daytime than in the nighttime and significantly less than those of NO and NO2.     

Dissociation of sulfur hexafluoride tracer gas in the presence of an indoor combustion source

As an odorless, nontoxic, and inert compound, sulfur hexafluoride (SF6) is one of the most widely used tracer gases in indoor air quality studies in both controlled and uncontrolled environments. This compound may be subject to reactions with water vapor under elevated temperature to form acidic inorganic compounds such as HF and H2SO4. Thus, in the presence of unvented combustion sources such as kerosene heaters, natural gas heaters, gas log fireplaces, candles, and lamps, the SF6 dissociation may interfere with measurements of the emissions from these sources. Tests were conducted in a research house with a vent-free natural gas heater to investigate these potential interferences. It was observed that the heater operation caused about a 5% reduction of SF6 concentration, which can be an error source for the ventilation rate measurement and consequently the estimated pollutant emission rates. Further analysis indicates that this error can be much greater than the observed 5% under certain test conditions because it is a function of the ventilation flow rate. Reducing the tracer gas concentration has no effect on this error. A simple theoretical model is proposed to estimate the magnitude of this error. The second type of interference comes from the primary and secondary products of the SF6 dissociation, mainly H2SO4, SO2, HF, and fine particulate matter (PM). In the presence of approximately 5 ppm SF6, the total airborne concentrations of these species increased by a factor of 4-10. The tests were performed at relatively high SF6 concentrations, which is necessary to determine the interferences quantitatively. The second type of interference can be significantly reduced if the SF6 concentration is kept at a low ppb level.     

Causes and Consequences of Backdrafting of Vented Gas Appliances

Abstract

House depressurization occurs when household equipment such as a kitchen or bathroom fan or a fireplace exhausts air from the house and lowers the pressure indoors with respect to the outside. The operation of air handlers for forced-air heating or cooling systems also can have a depressurization effect. This depressurization can hinder the natural draft from vented combustion appliances and lead to backdrafting, which in turn can result in combustion gases spilling into the indoor airspace. Extensive spillage can cause elevated indoor levels of combustion products such as carbon dioxide (CO2) and water vapor, as well as contaminants such as carbon monoxide (CO) and nitrogen dioxide (NO2).

The focus of this paper is to review studies on depressurization- induced backdrafting and spillage from gas-fired, drafthood equipped furnaces and domestic hot water heaters. Qualitative and quantitative techniques that were used in depressurization and backdrafting studies conducted in Canada, Europe, and the United States are analyzed. These studies have shown that exhaust fans operated simultaneously with fireplaces depressurize houses by 3 to 8 Pa on average. The CO indoor concentrations due to spillage, as reported in these studies, generally have been lower than 5 ppm. However, such low CO concentrations do not necessarily imply that a potential problem associated with backdrafting does not exist. Other combustion products, such as NO2, rarely have been measured in prior backdrafting studies.

It can be concluded from the literature review that causes of house depressurization are well understood. However, more comprehensive research is needed to better understand the frequency, duration, and severity of depressurization-induced spillage in a broad cross section of houses. Efforts in this direction have begun recently in the United States through a workshop to define research issues, pilot studies to develop comprehensive measurement protocols, and consensus standard development activities to prepare standardized methods and protocols.     

Probabilistic assessment of the potential indoor air impacts of vent-free gas heating appliances in energy-efficient homes in the United States

Use of vent-free gas heating appliances for supplemental heating in U.S. homes is increasing. However, there is currently a lack of information on the potential impact of these appliances on indoor air quality for homes constructed according to energy-efficient and green building standards. A probabilistic analysis was conducted to estimate the impact of vent-free gas heating appliances on indoor air concentrations of carbon monoxide (CO), nitrogen dioxide (NO₂), carbon dioxide (CO₂), water vapor, and oxygen in “tight” energy-efficient homes in the United States. A total of 20,000 simulations were conducted for each Department of Energy (DOE) heating region to capture a wide range of home sizes, appliance features, and conditions, by varying a number of parameters, e.g., room volume, house volume, outdoor humidity, air exchange rates, appliance input rates (Btu/hr), and house heat loss factors. Predicted airborne levels of CO were below the U.S. Environmental Protection Agency (EPA) standard of 9 ppm for all modeled cases. The airborne concentrations of NO₂ were below the U.S. Consumer Product Safety Commission (CPSC) guideline of 0.3 ppm and the Health Canada benchmark of 0.25 ppm in all cases and were below the World Health Organization (WHO) standard of 0.11 ppm in 99–100% of all cases. Predicted levels of CO₂ were below the Health Canada standard of 3500 ppm for all simulated cases. Oxygen levels in the room of vent-free heating appliance use were not significantly reduced. The great majority of cases in all DOE regions were associated with relative humidity (RH) levels from all indoor water vapor sources that were less than the EPA-recommended 70% RH maximum to avoid active mold and mildew growth. The conclusion of this investigation is that when installed in accordance with the manufacturer’s instructions, vent-free gas heating appliances maintain acceptable indoor air quality in tight energy-efficient homes, as defined by the standards referenced in this report.

Implications: Probabilistic modeling of indoor air concentrations of carbon monoxide (CO), nitrogen dioxide (NO₂), carbon dioxide (CO₂), water vapor, and oxygen associated with use of vent-free gas heating appliances provides new data indicating that uses of these devices are consistent with acceptable indoor air quality in “tight” energy-efficient homes in the United States. This study will provide authoritative bodies such as the International Code Council with definitive information that will assist in the development of future versions of national building codes, and will provide evaluation of the performance of unvented gas heating products in energy conservation homes.     

Dissociation of Sulfur Hexafluoride Tracer Gas in the Presence of an Indoor Combustion Source

ABSTRACT

As an odorless, nontoxic, and inert compound, sulfur hexafluoride (SF₆) is one of the most widely used tracer gases in indoor air quality studies in both controlled and uncontrolled environments. This compound may be subject to reactions with water vapor under elevated temperature to form acidic inorganic compounds such as HF and H₂SO₄. Thus, in the presence of unvented combustion sources such as kerosene heaters, natural gas heaters, gas log fireplaces, candles, and lamps, the SF₆ dissociation may interfere with measurements of the emissions from these sources. Tests were conducted in a research house with a vent-free natural gas heater to investigate these potential interferences. It was observed that the heater operation caused about a 5% reduction of SF₆ concentration, which can be an error source for the ventilation rate measurement and consequently the estimated pollutant emission rates. Further analysis indicates that this error can be much greater than the observed 5% under certain test conditions because it is a function of the ventilation flow rate. Reducing the tracer gas concentration has no effect on this error. A simple theoretical model is proposed to estimate the magnitude of this error.

The second type of interference comes from the primary and secondary products of the SF₆ dissociation, mainly H₂SO₄, SO₂, HF, and fine particulate matter (PM). In the presence of ~5 ppm SF₆, the total airborne concentrations of these species increased by a factor of 4-10. The tests were performed at relatively high SF₆ concentrations, which is necessary to determine the interferences quantitatively. The second type of interference can be significantly reduced if the SF₆ concentration is kept at a low ppb level.     

Indoor nitrogen dioxide exposure and children's pulmonary function

Elevated concentrations of nitrogen dioxide (NO2) are produced in the home by the use of unvented gas appliances. In studies on potential health effects of indoor exposure to NO2, exposure has mostly been estimated from the presence or absence of sources like gas cookers in the home. This leads to misclassification of exposure, as NO2 concentrations in the home depend also on source use, ventilation habits, time budgets, etc. The availability of cheap, passive monitoring devices has made it possible to measure indoor concentrations of NO2 directly in health effects studies, albeit with averaging times of one to several days. So far, it has not been evaluated whether this increases the sensitivity of a study to detect health effects of NO2. In this paper, a comparison is made between NO2 sources and weekly average indoor NO2 measurements, as predictors of pulmonary function in a study among children aged 6-12 years. The relationship between exposure and lung functions was found to be generally non-significant in this study. The results further suggested that in this study, measuring indoor NO2 concentrations with passive monitors offered no advantage over the simple use of source presence as exposure variable.     

Effect of Gas and Kerosene Space Heaters on Indoor Air Quality: A Study in Homes of Santiago,Chile

Abstract

The impact of outdoor and indoor pollution sources on indoor air quality in Santiago, Chile was investigated. Toward this end, 16 homes were sampled in four sessions. Each session included an outdoor site and four homes using different unvented space heaters (electric or central heating, compressed natural gas, liquefied petroleum gas, and kerosene). Average outdoor fine particulate matter (PM_2.5) concentrations were very high (55.9 μg·m^-3), and a large fraction of these particles penetrated indoors. PM_2.5 and several PM_2.5 components (including sulfate, elemental carbon, organic carbon, metals, and polycyclic aromatic hydrocarbons) were elevated in homes using kerosene heaters. Nitrogen dioxide (NO₂) and ultrafine particles (UFPs) were higher in homes with combustion heaters as compared with those with electric heaters or central heating. A regression model was used to assess the effect of heater use on continuous indoor PM_2.5 concentrations when windows were closed. The model found an impact only for kerosene heaters (45.8 μg m^-3).     

Indoor house pollution: Appliance emissions and indoor ambient concentrations

Emission rates for CO, NO, NO₂ and CH₂O from several unvented gas and kerosene heaters frequently employed in domestic heating have been measured. The indoor concentrations generated by these emissions are evaluated and compared to those determined in typical houses. It is found that both the predicted and measured values exceed the short term air quality standards accepted in most countries.     

Evaluation of Tire-Derived Fuel for Use in Nitrogen Oxide Reduction by Reburning

ABSTRACT

Tire-derived fuel (TDF) was tested in a small-scale (44 kW or 150,000 Btu/hr) combustor to determine its feasibility as a fuel for use in reburning for control of nitrogen oxide (NO). TDF was gravity-fed into upward flowing combustion gases from a primary natural gas flame doped with ammonia to simulate a high NO combustion process. Emissions of NO, oxygen, carbon dioxide, carbon monoxide, and particulate matter were measured. The tests varied the nominal primary NO level from 600 to 1,200 ppm and the primary stoichiometry from 1.1 to 1.2, and used both natural gas and TDF as reburn fuels. The reburn injection rate was varied to achieve 8–20% of the total heat input from the reburn fuel. NO emissions reductions ranged between 20 and 63% when using TDF, depending upon the rate of TDF injection, primary NO, and primary stoichiometry. NO emission reductions when using natural gas as the reburn fuel were consistently higher than those when using TDF. While additional work remains to optimize the process and evaluate costs, TDF has been shown to have the potential to be a technically viable reburning fuel.     

Emission rates from range-top burners—Assessment of measurement methods

Unvented combustion sources in indoor environments generate emissions that contribute to indoor air pollution. Both the direct and mass-balance methods have been used to measure emission rates from these sources in field houses, test houses and chambers. In particular, emission rates have been obtained for pollutants from kerosene space heaters and from unvented gas appliances such as range-top burners, ovens, dryers and gas space heaters.Most studies have focused on the emission rates of the inorganic air constituents (NO, NO₂, CO and a few others). This paper compares the two methods of emission rate measurement, and summarizes the emission rates of NO, NO₂ and CO from range-top burners.The emission rates of NO, NO₂ and CO from range-top burners are well quantified, but vary widely as a function of the source condition. The experiments described herein found that the two methods provide comparable emission rates. Consequently, in support of the research needed to establish the distribution of emission rates from range-top burners in the U.S. housing stock, the method to be employed should be the one that provides the required information cost effectively.     

Evaluation of a Probabilistic Exposure Model Applied

The probabilistic National Ambient Air Quality Standards (NAAQS) Exposure Model applied to carbon monoxide (pNEM/CO) was developed by the U.S. Environmental Protection Agency (EPA) to estimate frequency distributions of population exposure to carbon monoxide (CO) and the resulting carboxyhemoglobin (COHb) levels. To evaluate pNEM/CO, the model was set up to simulate CO exposure data collected during a Denver Personal Exposure Monitoring Study (PEM) conducted during the winter of 1982-1983.

This paper compares computer-simulated exposure distributions obtained by pNEM/CO with the observed cumulative

relative frequency distributions of population exposure to CO from 779 people in the Denver PEM study. The subjects were disaggregated into two categories depending upon whether they lived in a home with a gas stove or an electric stove. The observed and predicted population exposure frequency distributions were compared in terms of 1-hr daily maximum exposure (1DME) and 8-hr daily maximum moving average exposure (8DME) for people living in homes with gas stove or an electric stove. For 1DME, the computer-simulated results from pNEM/CO agreed most closely within the range of 6-13 ppm, but overestimated occurrences at low exposure (<6 ppm) and underestimated occurrences at high exposure (>13 ppm). For 8DME, the predicted exposures agreed best with observed exposures in the range of CO concentration between 5.5 and 7 ppm, and over-predicted occurrences below 5.5 ppm and under-predicted occurrences above 7 ppm.     

Evaluation of a Probabilistic Exposure Model Applied to Carbon Monoxide (pNEM/CO) Using Denver Personal Exposure Monitoring Data

The probabilistic National Ambient Air Quality Standards (NAAQS) Exposure Model applied to carbon monoxide (pNEM/CO) was developed by the U.S. Environmental Protection Agency (EPA) to estimate frequency distributions of population exposure to carbon monoxide (CO) and the resulting carboxyhemoglobin (COHb) levels. To evaluate pNEM/CO, the model was set up to simulate CO exposure data collected during a Denver Personal Exposure Monitoring Study (PEM) conducted during the winter of 1982-1983. This paper compares computer-simulated exposure distributions obtained by pNEM/CO with the observed cumulative relative frequency distributions of population exposure to CO from 779 people in the Denver PEM study.

The subjects were disaggregated into two categories depending upon whether they lived in a home with a gas stove or an electric stove. The observed and predicted population exposure frequency distributions were compared in terms of 1-hr daily maximum exposure (1DME) and 8-hr daily maximum moving average exposure (8DME) for people living in homes with gas stove or an electric stove. For 1DME, the

computer-simulated results from pNEM/CO agreed most closely within the range of 6-13 ppm, but overestimated occurrences at low exposure (<6 ppm) and underestimated occurrences at high exposure (>13 ppm). For 8DME, the predicted exposures agreed best with observed exposures in the range of CO concentration between 5.5 and 7 ppm, and over-predicted occurrences below 5.5 ppm and under-predicted occurrences above 7 ppm.     

Transformations,Lifetimes, and Sources of NO2, HONO,and HNO3 in Indoor Environments

Recent research has demonstrated that nitrogen oxides are transformed to nitrogen acids in indoor environments, and that significant concentrations of nitrous acid are present in indoor air. The purpose of the study reported in this paper has been to investigate the sources, chemical transformations and lifetimes of nitrogen oxides and nitrogen acids under the conditions existing in buildings. An unoccupied single family residence was instrumented for monitoring of NO, NO₂, NO_y, MONO, HNO₃, CO, temperature, relative humidity, and air exchange rate. For some experiments, NO₂ and HONO were injected into the house to determine their removal rates and lifetimes. Other experiments investigated the emissions and transformations of nitrogen species from unvented natural gas appliances. We determined that HONO is formed by both direct emissions from combustion processes and reaction of NO₂ with surfaces present indoors. Equilibrium considerations influence the relative contributions of these two sources to the indoor burden of HONO. We determined that the lifetimes of trace nitrogen species varied in the order NO ~ HONO > NO₂ >HNO₃. The lifetimes with respect to reactive processes are on the order of hours for NO and HONO, about an hour for NO₂, and 30 minutes or less for HNO3. The rapid removal of NO₂ and long lifetime of HONO suggest that HONO may represent a significant fraction of the oxidized nitrogen burden in indoor air.     

Automobile Exhaust Control Devices

Irritant gases in concentrations that occur in polluted atmospheres might play a role in the degranulation and histamine release processes of mast cells in lung tissue. To test this hypothesis, young rats weighing 140-150 g were exposed to 1 ppm nitrogen dioxide for 2 hr. One group was killed immediately, and another group 24-27 hr after exposure. A third group was exposed to 0.5 ppm nitrogen dioxide for 4 hr and killed immediately. Animals serving as controls were placed for 1 hr into the exposure chamber ventilated with ambient air. Standard histological preparations were made after Carnoy’s fixative and subsequent staining with toluidine blue. The mast cells of the control animals appeared relatively intact with no evidence of disorientation. The cells of the animals exposed to NO2 and sacrificed immediately revealed rupture and loss of cytoplasmic granules with some disorientation. These changes were observed in the pleura, bronchi, and surrounding tissue with the effects more marked in the mediastinum. The mast cells of exposed animals sacrificed about 24-27 hr after discontinuing the exposure showed in some cases a combination of ruptured and intact cells with a predominance of the latter, and in other cases could not be differentiated from the controls. These findings indicate that 24 hr or more are required to reverse the acute effects of NO2 inhalation. The toxicological implications will be discussed. The release of granular substances in the lung tissue when NO2 is inhaled signifies the onset of an acute inflammation.     

Effects of Operational Factors on Pollutant Emission Rates from Residential Gas Appliances

The NO, NO₂, and CO emissions from residential gas combustion appliances contribute to indoor air pollution. The work described investigated the impact of various unvented gas appliances designs and/or operational factors on pollutant emission rates. All experiments were performed in a 1150 ft³ (32.56 m³) all aluminum chamber under controlled conditions. Results are presented for the effect of the following factors on emission rates: 1) appliance type and/or design, 2) primary aeration level, 3) firing rate (fuel input rate), 4) chamber humidity, and 5) time dependence of emission rates. It is concluded that primary aeration level has the largest impact on pollutant emission rates of range-top burners, followed in turn by firing rate, appliance type, chamber humidity, and time dependence of emission rate.     

Low NOx,High Efficiency Multistaged Burner: Fuel Oil Results

A multistaged combustion burner designed for in-furnace NO_x control and high combustion efficiency is being evaluated for high nitrogen content fuel and waste incineration application in a 0.6 MW package boiler simulator. A low NO_x precombustion chamber burner has been reduced in size by approximately a factor of two (from 600 to 250 ms first-stage residence time) and coupled with (1) air staging, resulting in a three-stage configuration, and (2) natural gas fuel staging, yielding up to four stolchlometric zones. Natural gas, doped with ammonia to yield a 5.8 percent fuel nitrogen content, and distillate fuel oil, doped with pyridine to yield a 2 percent fuel nitrogen content, were used to simulate high nitrogen content fuel/waste mixtures. The multistaged burner reduced NO emissions by 85 percent from emission levels from a conventional unstaged burner mounted on a commercial package bollerTA minimum NO emission level of 110 ppm was achieved in the fuel oil tests, from a level of 765 ppm for conventional firing. This is compared with a 160 ppm minimum NO level achieved in gaseous fuel tests, from an uncontrolled level of 1000 ppm. Boiler fuel staging, or reburnlng, appears to be superior to air staging for high combustion efficiency due to its minimal fuel-rich core and second flame front in the boiler.     

Evaluating the effects of elevated levels of atmospheric trace gases on herbs and shrubs: a prototype dual array field exposure system

In the context of global climate change, an understanding of the long-term effects of increasing concentrations of atmospheric trace gases (carbon dioxide, CO(2), ozone, O(3), oxides of nitrogen, NO(x) etc.) on both cultivated and native vegetation is of utmost importance. Over the years, under field conditions, various trace gas-vegetation exposure methodologies with differing advantages and disadvantages have been used. Because of these variable criteria, with elevated O(3) or CO(2) levels, at the present time the approach of free-air experimental-release of the gas into study plots is attracting much attention. However, in the case of CO(2), this approach (using 15 m diameter study plot with a single circular array of vent pipes) has proven to be cost prohibitive (about 59000-98000 dollars/year/replicate) due to the consumption of significant quantities of the gas to perform the experiment (CO(2) level elevated to 400 ppm above the ambient). Therefore, in this paper, we present a new approach consisting of a dual, concentric exposure array of vertical risers or vent pipes. The purpose of the outer array (17 m diameter) is to vent ambient air outward and toward the incoming wind, thus providing an air curtain to reduce the velocity of that incoming wind to simulate the mode or the most frequently occurring wind speed at the study site. The inner array (15 m diameter) vents the required elevated levels of trace gases (CO(2), O(3), etc.) into the study plot. This dual array system is designed to provide spatial homogeneity (shown through diffusion modeling) of the desired trace-gas levels within the study plot and to also reduce its consumption. As an example, while in the single-array free-air CO(2)-release system the consumption of CO(2) to elevate its ambient concentration by 400 ppm is calculated to be about 980 tons/year/replicate, it is estimated that in the dual array system it would be approximately 590 tons/year/replicate. Thus, the dual array system may provide substantial cost savings (24000-39000 dollars/year/replicate) in the CO(2) consumption (60-100 dollars/ton of CO(2)) alone. Similarly, benefits in the requirements of other trace gases (O(3), NO(x), etc.) are expected, in future multivariate studies on global climate change.     

Occurrence of carbon monoxide during organic waste degradation

The concentrations of carbon monoxide (CO) and other gases were measured in the emissions from solid waste degradation under aerobic and anaerobic conditions during laboratory and field investigations. The emissions were measured as room temperature headspace gas concentrations in reactors of 1, 30, and 150 L, as well as sucked gas concentrations from windrow composting piles and a biocell, under field conditions. The aerobic composting laboratory experiments consisted of treatments with and without lime. The CO concentrations measured during anaerobic conditions varied from 0 to 3000 ppm, the average being 23 ppm, increasing to 133 ppm when methane (CH4) concentrations were low. The mean/maximum CO concentrations during the aerobic degradation in the 2-L reactor were 101/194 ppm without lime, 486/2022 ppm with lime, and 275/980 ppm in the 150-L reactors. The presence of CO during the aerobic composting followed a rapid decline in O2 concentrations Significantly higher CO concentrations were obtained when the aerobic degradation was amended with lime, probably because of a more extreme depletion of oxygen. The mean/maximum CO concentrations under field conditions during aerobic composting were 95/1000 ppm. The CO concentrations from the anaerobic biocell varied from 20 to 160 ppm. The hydrogen sulfide concentrations reached almost 1200 ppm during the anaerobic degradation and 67 ppm during the composting experiments.     

Monitoring of carbon monoxide in residences with bulk wood pellet storage in the Northeast United States

The interest in biomass fuel is continuing to expand globally and in the northeastern United States as wood pellets are becoming a primary source of fuel for residential and small commercial systems. Wood pellets for boilers are often stored in basement storage rooms or large bag-type containers. Due to the enclosed nature of these storage areas, the atmosphere may exhibit increased levels of carbon monoxide. Serious accidents in Europe have been reported over the last decade in which high concentrations of carbon monoxide (CO) have been found in or near bulk pellet storage containers. The aim of this study was to characterize the CO concentrations in areas with indoor storage of bulk wood pellets. Data was obtained over approximately 7 months (December 2013 to June 2014) at 25 sites in New Hampshire and Massachusetts: 16 homes using wood pellet boilers with indoor pellet storage containers greater than or equal to 3 ton capacity; 4 homes with wood pellet heating systems with outdoor pellet storage; 4 homes using other heating fuels; and a university laboratory site. CO monitors were set up in homes to collect concentrations of CO in the immediate vicinity of wood pellet storage containers, and data were then compared to those of homes using fossil fuel systems. The homes monitored in this study provided a diverse set of housing stock spanning two and a half centuries of construction, with homes built from 1774 to 2013, representing a range of air exchange rates. The CO concentration data from each home was averaged hourly and then compared to a threshold of 9 ppm. While concentrations of CO were generally low for the homes studied, the need to properly design storage locations for pellets is and will remain a necessary component of wood pellet heating systems to minimize the risk of CO exposure.

Implications: This paper is an assessment of carbon monoxide (CO) exposure from bulk wood pellet storage in homes in New Hampshire and Massachusetts. Understanding the CO concentrations in homes allows for better designs for storage bins and ventilation for storage areas. Hence, uniform policies for stored wood pellets in homes, schools, and businesses can be framed to ensure occupant safety. Currently in New York State rebates for the installation of wood pellet boilers are only provided if the bulk pellet storage is outside of the home, yet states such as New Hampshire, Vermont, and Maine currently do not have these restrictions.     

Occurrence of Carbon Monoxide during Organic Waste Degradation

Abstract

The concentrations of carbon monoxide (CO) and other gases were measured in the emissions from solid waste degradation under aerobic and anaerobic conditions during laboratory and field investigations. The emissions were measured as room temperature headspace gas concentrations in reactors of 1, 30, and 150 L, as well as sucked gas concentrations from windrow composting piles and a biocell, under field conditions. The aerobic composting laboratory experiments consisted of treatments with and without lime. The CO concentrations measured during anaerobic conditions varied from 0 to 3000 ppm, the average being 23 ppm, increasing to 133 ppm when methane (CH₄) concentrations were low. The mean/maximum CO concentrations during the aerobic degradation in the 2-L reactor were 101/194 ppm without lime, 486/2022 ppm with lime, and 275/980 ppm in the 150-L reactors. The presence of CO during the aerobic composting followed a rapid decline in O₂ concentrations Significantly higher CO concentrations were obtained when the aerobic degradation was amended with lime, probably because of a more extreme depletion of oxygen. The mean/maximum CO concentrations under field conditions during aerobic composting were 95/1000 ppm. The CO concentrations from the anaerobic biocell varied from 20 to 160 ppm. The hydrogen sulfide concentrations reached almost 1200 ppm during the anaerobic degradation and 67 ppm during the composting experiments. There is a positive correlation between the CO and hydrogen sulfide concentrations measured during the anaerobic degradation experiments.