Removal of ammonium and nitrate through Anammox and FeS-driven autotrophic denitrification

● Simultaneous NH₄⁺/NO₃^– removal was achieved in the FeS denitrification system ● Anammox coupled FeS denitrification was responsible for NH₄⁺/NO₃^– removal ● Sulfammox, Feammox and Anammox occurred for NH₄⁺ removal ● Thiobacillus, Nitrospira , and Ca. Kuenenia were key functional microorganisms An autotrophic denitrifying bioreactor with iron sulfide (FeS) as the electron donor was operated to remove ammonium (NH₄⁺) and nitrate (NO₃⁻) synergistically from wastewater for more than 298 d. The concentration of FeS greatly affected the removal of NH₄⁺/NO₃⁻. Additionally, a low hydraulic retention time worsened the removal efficiency of NH₄⁺/NO₃⁻. When the hydraulic retention time was 12 h, the optimal removal was achieved with NH₄⁺ and NO₃⁻ removal percentages both above 88%, and the corresponding nitrogen removal loading rates of NH₄⁺ and NO₃⁻ were 49.1 and 44.0 mg/(L·d), respectively. The removal of NH₄⁺ mainly occurred in the bottom section of the bioreactor through sulfate/ferric reducing anaerobic ammonium oxidation (Sulfammox/Feammox), nitrification, and anaerobic ammonium oxidation (Anammox) by functional microbes such as Nitrospira, Nitrosomonas, and Candidatus Kuenenia. Meanwhile, NO₃⁻ was mainly removed in the middle and upper sections of the bioreactor through autotrophic denitrification by Ferritrophicum, Thiobacillus, Rhodanobacter, and Pseudomonas, which possessed complete denitrification-related genes with high relative abundances.     

Perfluoroalkane acids in human milk under the global monitoring plan of the Stockholm Convention on Persistent Organic Pollutants (2008–2019)

● Perfluorooctanesulfonic acid and perfluorooctanoic acid highest in human milk. ● All other perfluoroalkane substances had median values of zero (101 samples). ● Branched PFOS recommended to be analyzed separately from linear isomer. ● PFOS and PFOA showed differentiated regional and income distribution. ● Human health risk assessment values not yet available at global level. Within the global monitoring plan (GMP) established by article 16 of the Stockholm Convention on Persistent Organic Pollutants, perfluorooctane sulfonic acid (PFOS), perfluorooctanoic acid (PFOA), and perfluorohexane sulfonic acid (PFHxS) are recommended for analysis in core matrices to assess occurrence and changes geographically and with time. In 101 samples consisting of 86 national pools and 15 pools from States in Brazil obtained between 2008 and 2019, PFHxS was detected in 17% of the national pools and none in Brazil. PFOA and PFOS had a detection frequency of 100% and 92%, respectively. Other perfluoroalkane substances (PFAS) had either low detection frequencies and median values of zero (carboxylic acids C₄–C₁₁; except PFOA) or could not be quantified in any sample (sulfonic acids, C₄–C₁₀, and long-chain carboxylic acids, C₁₂–C₁₄). Correlation between PFOA and PFOS was moderately (r = 0.58). Whereas median values were almost identical (18.9 pg/g f.w. for PFOS; 18.6 pg/g f.w. for PFOA), PFOS showed larger ranges (< 6.2 pg/g f.w.–212 pg/g f.w.) than PFOA (< 6.2 pg/g f.w.–63.4 pg/g f.w.). It was shown that wealthier countries had higher PFOA concentrations than poorer countries. No difference in concentrations was found for samples collected in countries having or not having ratified the Stockholm Convention amendments to list PFOS or PFOA. The goal to achieve 50% decrease in concentrations within ten years was met by Antigua and Barbuda, Kenya, and Nigeria for PFOS and by Antigua and Barbuda for PFOA. In a few cases, increases were observed; one country for PFOS, four countries for PFOA.     

A pyrazine based metal-organic framework for selective removal of copper from strongly acidic solutions

● pz-UiO-66 was synthesized facilely by a solvothermal method. ● Efficient capture of copper from highly acidic solution was achieved by pz-UiO-66. ● pz-UiO-66 exhibited excellent selectivity and capacity for copper capture. ● Pyrazine-N in pz-UiO-66 was shown to be the dominant adsorption site. The selective capture of copper from strongly acidic solutions is of vital importance from the perspective of sustainable development and environmental protection. Metal organic frameworks (MOFs) have attracted the interest of many scholars for adsorption due to their fascinating physicochemical characteristics, including adjustable structure, strong stability and porosity. Herein, pz-UiO-66 containing a pyrazine structure is successfully synthesized for the efficient separation of copper from strongly acidic conditions. Selective copper removal at low pH values is accomplished by using this material that is not available in previously reported metal–organic frameworks. Furthermore, the material exhibits excellent adsorption capacity, with a theoretical maximum copper uptake of 247 mg/g. As proven by XPS and FT-IR analysis, the coordination of pyrazine nitrogen atoms with copper ions is the dominant adsorption mechanism of copper by pz-UiO-66. This work provides an opportunity for efficient and selective copper removal under strongly acidic conditions, and promises extensive application prospects for the removal of copper in the treatment for acid metallurgical wastewater.     

Adsorption behavior of imidacloprid pesticide on polar microplastics under environmental conditions: critical role of photo-aging

● Small molecular chains formed on photo-aged polylactic acid microplastics (MPs). ● Oxygen-containing functional groups generated on photo-aged polyamide MPs. ● Photo-aging has the opposite influence on the imidacloprid adsorption on two MPs. ● Electrostatic interactions and hydrogen bonds were the main mechanisms. ● High pH value and low ionic strength increase the adsorption capacity. The photo-aging behavior of microplastics (MPs) in natural environment has become a global concern. The ultraviolet radiation has enough energy to change the polymer structure and physical-chemical properties of MPs. Less attention has focused on the interactions of the photo-aged polar and biodegradable MPs with organic pollutants. This work investigated the structural properties of aged polar polyamide (PA) MPs and biodegradable polylactic acid (PLA) MPs exposed to ultraviolet irradiation and their adsorption behavior and mechanism for neonicotinoid insecticide imidacloprid (IMI). The results showed that the MPs had extensive changes in surface morphology and chemical properties after photo-aging. The C–N bond of PA MPs was disrupted to form more carbonyl groups. The oxygen-containing functional groups on the surface of aged PLA MPs were broken and generated relatively smaller molecules. The adsorption capacity of IMI on PA MPs decreased by 19.2 %, while the adsorption capacity of IMI on PLA MPs increased by 41.2 % after photo-aging. This depended on the natural structure of the MPs and their ability to absorb ultraviolet light. The electrostatic interactions, hydrogen bonds, van der Waals interactions, and polar-polar interactions were the main adsorption mechanisms of IMI on MPs. High initial solution pH and low ionic strength favored the adsorption of IMI by altering charge distribution on the MPs surface. The formation of the humic acid-IMI complexes decreased the concentration of IMI in the water phase and further decreased the adsorption on MPs. These results are enlightening for a scientific comprehension of the environmental behavior of the polar MPs.     

Control strategies for disinfection byproducts by ion exchange resin,nanofiltration and their sequential combination

● Effects of AER adsorption and NF on DBP precursors, DBPs, and TOX were examined. ● A treatment approach of resin adsorption followed by nanofiltration was developed. ● Both DOC and Br⁻ could be effectively removed by the sequential approach. ● DBPs, TOX, and cytotoxicity were significantly reduced by the sequential approach. Disinfection byproducts (DBPs) are emerging pollutants in drinking water with high health risks. Precursor reduction before disinfection is an effective strategy to control the formation of DBPs. In this study, three types of anion exchange resins (AERs) and two types of nanofiltration (NF) membranes were tested for their control effects on DBP precursors, DBPs, and total organic halogen (TOX). The results showed that, for AER adsorption, the removal efficiencies of DBP precursors, DBPs, and TOX increased with the increase of resin dose, and the strong basic macroporous anion exchange resin (M500MB) had the highest removal efficiencies. For NF, the highest removal efficiencies were achieved at an operating pressure of 4 bar, and the membrane (NF90) with a smaller molecular weight cut-off, had a better control efficiency. However, AER adsorption was inefficient in removing dissolved organic carbon (DOC); NF was inefficient in removing Br⁻ resulting in insufficient control of Br-DBPs. Accordingly, a sequential approach of AER (M500MB) adsorption followed by NF (NF90) was developed to enhance the control efficiency of DBPs. Compared with single AER adsorption and single NF, the sequential approach further increased the removal efficiencies of DOC by 19.4%–101.9%, coupled with the high Br⁻ removal efficiency of 92%, and thus improved the reduction of cyclic DBPs and TOX by 3.5%–4.9%, and 2.4%–8.4%, respectively; the sequential approach also reduced the cytotoxicity of the water sample by 66.4%.     

Penicillin fermentation residue biochar as a high-performance electrode for membrane capacitive deionization

● We have provided an activated method to remove the toxicity of antibiotic residue. ● PFRB can greatly improve the salt adsorption capacity of MCDI. ● The hierarchical porous and abundant O/N-doped played the key role for the high-capacity desalination. ● A new field of reuse of penicillin fermentation residue has been developed. Membrane capacitive deionization (MCDI) is an efficient desalination technology for brine. Penicillin fermentation residue biochar (PFRB) possesses a hierarchical porous and O/N-doped structure which could serve as a high-capacity desalination electrode in the MCDI system. Under optimal conditions (electrode weight, voltage, and concentration) and a carbonization temperature of 700 °C, the maximum salt adsorption capacity of the electrode can reach 26.4 mg/g, which is higher than that of most carbon electrodes. Furthermore, the electrochemical properties of the PFRB electrode were characterized through cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) with a maximum specific capacitance of 212.18 F/g. Finally, biotoxicity tests have showed that PFRB was non-biotoxin against luminescent bacteria and the MCDI system with the PFRB electrode remained stable even after 27 adsorption–desorption cycles. This study provides a novel way to recycle penicillin residue and an electrode that can achieve excellent desalination.     

Simple fabrication of carboxymethyl cellulose and κ-carrageenan composite aerogel with efficient performance in removal of fluoroquinolone antibiotics from water

● A composite aerogel was simply obtained to remove various fluoroquinolones (FQs). ● The structural and textural properties of this composite aerogel are improved. ● Its adsorption capacity was improved at a low content of coexisting Cu²⁺ or Fe³⁺ ion. ● Two substructural analogs of FQs are compared to explore the adsorption mechanisms. ● This aerogel after saturated adsorption can be reused directly for Cu²⁺ adsorption. 3D composite aerogels (CMC-CG) composed of carboxymethyl cellulose and κ-carrageenan were designed and fabricated using the one-pot synthesis technique. The optimized CMC-CG showed a good mechanical property and a high swelling ratio due to its superior textural properties with a proper chemically cross-linked interpenetrating network structure. CMC-CG was utilized for the removal of various fluoroquinolones (FQs) from water and exhibited high adsorption performance because of effective electrostatic attraction and hydrogen bonding interactions. Ciprofloxacin (CIP), a popular FQ, was used as the representative. The optimized CMC-CG had a theoretically maximal CIP uptake of approximately 1.271 mmol/g at the pH of 5.0. The adsorption capacity of CMC-CG was improved in the presence of some cations, Cu²⁺ and Fe³⁺ ions, at a low concentration through the bridging effect but was reduced at a high concentration. The investigation of adsorption mechanisms, based on the adsorption kinetics, isotherms and thermodynamic study, Fourier transform infrared spectrometry and X-ray photoelectron spectroscopy analyses before and after adsorption, and changes in the adsorption performance of CMC-CG toward two molecular probes, further indicated that electrostatic attraction was the dominant interaction rather than hydrogen bonding in this adsorption. CMC-CG after saturated adsorption of CIP could be easily regenerated using a dilute NaCl aqueous solution and reused efficiently. Moreover, the disused aerogel could still be reused as a new adsorbent for effective adsorption of Cu²⁺ ion. Overall, this study suggested the promising applications of this composite aerogel as an eco-friendly, cost-effective, and recyclable adsorbent for the efficient removal of FQs from water.     

Effect of loading rate on shear strength parameters of mechanically and biologically treated waste

● Mechanical behavior of MBT waste affected by loading rate was investigated. ● Shear strength ratio of MBT waste increases with an increase in loading rate. ● Cohesion is inversely related to loading rate. ● Internal friction angles are positively related to loading rate. ● MBT waste from China shows smaller range of φ. Mechanical biological treatment (MBT) technology has attracted increasing attention because it can reduce the volume of waste produced. To deal with the current trend of increasing waste, MBT practices are being adopted to address waste generated in developing urban societies. In this study, a total of 20 specimens of consolidated undrained triaxial tests were conducted on waste obtained from the Hangzhou Tianziling landfill, China, to evaluate the effect of loading rate on the shear strength parameters of MBT waste. The MBT waste samples exhibited an evident strain-hardening behavior, and no peak was observed even when the axial strain exceeded 25%. Further, the shear strength increased with an increase in the loading rate; the effect of loading rate on shear strength under a low confining pressure was greater than that under a high confining pressure. Furthermore, the shear strength parameters of MBT waste were related to the loading rate. The relationship between the cohesion, internal friction angle, and logarithm of the loading rate could be fitted to a linear relationship, which was established in this study. Finally, the ranges of shear strength parameters cohesion c and effective cohesion c ´ were determined as 1.0–8.2 kPa and 2.1–14.9 kPa, respectively; the ranges of the internal friction angle φ and effective internal friction angle φ ´ were determined as 16.2°–29° and 19.8°–43.9°, respectively. These results could be used as a valuable reference for conducting stability analyses of MBT landfills.     

Advancing ion-exchange membranes to ion-selective membranes: principles,status, and opportunities

● IEM ion/ion selectivities of charge, valence, & specific ion are critically assessed. ● Ion/molecule selectivities of ion/solvent and ion/uncharged solute are reviewed. ● Approaches to advance the selectivities through sorption and migration are analyzed. ● The permeability-selectivity tradeoff appears to be pervasive. ● Ion/molecule selectivities are comparatively underdeveloped and poorly understood. Ion-exchange membranes (IEMs) are utilized in numerous established, emergent, and emerging applications for water, energy, and the environment. This article reviews the five different types of IEM selectivity, namely charge, valence, specific ion, ion/solvent, and ion/uncharged solute selectivities. Technological pathways to advance the selectivities through the sorption and migration mechanisms of transport in IEM are critically analyzed. Because of the underlying principles governing transport, efforts to enhance selectivity by tuning the membrane structural and chemical properties are almost always accompanied by a concomitant decline in permeability of the desired ion. Suppressing the undesired crossover of solvent and neutral species is crucial to realize the practical implementation of several technologies, including bioelectrochemical systems, hypersaline electrodialysis desalination, fuel cells, and redox flow batteries, but the ion/solvent and ion/uncharged solute selectivities are relatively understudied, compared to the ion/ion selectivities. Deepening fundamental understanding of the transport phenomena, specifically the factors underpinning structure-property-performance relationships, will be vital to guide the informed development of more selective IEMs. Innovations in material and membrane design offer opportunities to utilize ion discrimination mechanisms that are radically different from conventional IEMs and potentially depart from the putative permeability-selectivity tradeoff. Advancements in IEM selectivity can contribute to meeting the aqueous separation needs of water, energy, and environmental challenges.     

Contributions of adsorption,bioreduction and desorption to uranium immobilization by extracellular polymeric substances

● EPS immobilizes U(VI) via adsorption, bioreduction and desorption. ● This work provides a framework to quantify the three immobilization processes. ● The non-equilibrium adsorption of U follows pseudo-second-order kinetics. ● The equilibrium adsorption of U followed Langmuir and Freundlich isotherms. Hexavalent uranium (U(VI)) can be immobilized by various microbes. The role of extracellular polymeric substances (EPS) in U(VI) immobilization has not been quantified. This work provides a model framework to quantify the contributions of three processes involved in EPS-mediated U(VI) immobilization: adsorption, bioreduction and desorption. Loosely associated EPS was extracted from a pure bacterial strain, Klebsiella sp. J1, and then exposed to H₂ and O₂ (no bioreduction control) to immobilize U(VI) in batch experiments. U(VI) immobilization was faster when exposed to H₂ than O₂ and stabilized at 94% for H₂ and 85% for O₂, respectively. The non-equilibrium data from the H₂ experiments were best simulated by a kinetic model consisting of pseudo-second-order adsorption (k_a = 2.87 × 10⁻³ g EPS·(mg U)⁻¹·min⁻¹), first-order bioreduction (k_b = 0.112 min⁻¹) and first-order desorption (k_d = 7.00 × 10⁻³ min⁻¹) and fitted the experimental data with R² of 0.999. While adsorption was dominant in the first minute of the experiments with H₂, bioreduction was dominant from the second minute to the 50^th min. After 50 min, adsorption was negligible, and bioreduction was balanced by desorption. This work also provides the first set of equilibrium data for U(VI) adsorption by EPS alone. The equilibrium experiments with O₂ were well simulated by both the Langmuir isotherm and the Freundlich isotherm, suggesting multiple mechanisms involved in the interactions between U(VI) and EPS. The thermodynamic study indicated that the adsorption of U(VI) onto EPS was endothermic, spontaneous and favorable at higher temperatures.     

Collaborative control of fine particles and ozone required in China for health benefit

● Increased DAAO offsets 3/4 of the decrease of DAAP in 2013–2020. ● DAAO increases are mainly due to O₃ concentration increase and population aging. ● Health benefit from PM_2.5 reduction after 2017 is larger than that before 2017. ● Reducing PM_2.5 concentration by 1% results in 0.6% reduction of DAAP. ● Reducing O₃ concentration by 1% results in 2% reduction of DAAO. PM_2.5 concentration declined significantly nationwide, while O₃ concentration increased in most regions in China in 2013–2020. Recent evidences proved that peak season O₃ is related to increased death risk from non-accidental and respiratory diseases. Based on these new evidences, we estimate excess deaths associated with long-term exposure to ambient PM_2.5 and O₃ in China following the counterfactual analytic framework from Global Burden Disease. Excess deaths from non-accidental diseases associated with long-term exposure to ambient O₃ in China reaches to 579 (95% confidential interval (CI): 93, 990) thousand in 2020, which has been significantly underestimated in previous studies. In addition, the increased excess deaths associated with long-term O₃ exposure (234 (95% CI: 177, 282) thousand) in 2013–2020 offset three quarters of the avoided excess deaths (302 (95% CI: 244, 366) thousand) mainly due to PM_2.5 exposure reduction. In key regions (the North China Plain, the Yangtze River Delta and the Fen-Wei Plain), the former is even larger than the latter, particularly in 2017–2020. Health benefit of PM_2.5 concentration reduction offsets the adverse effects of population growth and aging on excess deaths attributed to PM_2.5 exposure. Increase of excess deaths associated with O₃ exposure is mainly due to the strong increase of O₃ concentration, followed by population aging. Considering the faster population aging process in the future, collaborative control, and faster reduction of PM_2.5 and O₃ are needed to reduce the associated excess deaths.     

A hybrid fuel cell for water purification and simultaneously electricity generation

● A novel hybrid fuel cell (F-HFC) was fabricated. ● Pollutant degradation and synchronous electricity generation occurred in F-HFC. ● BiOCl-NH₄PTA photocatalyst greatly improved electron transfer and charge separation. ● Pollutant could act as substrate directly in ambient conditions without pretreatment. ● The mechanism of the F-HFC was proposed and elucidated. The development of highly efficient energy conversion technologies to extract energy from wastewater is urgently needed, especially in facing of increasing energy and environment burdens. Here, we successfully fabricated a novel hybrid fuel cell with BiOCl-NH₄PTA as photocatalyst. The polyoxometalate (NH₄PTA) act as the acceptor of photoelectrons and could retard the recombination of photogenerated electrons and holes, which lead to superior photocatalytic degradation. By utilizing BiOCl-NH₄PTA as photocatalysts and Pt/C air-cathode, we successfully constructed an electron and mass transfer enhanced photocatalytic hybrid fuel cell with flow-through field (F-HFC). In this novel fuel cell, dyes and biomass could be directly degraded and stable power output could be obtained. About 87 % of dyes could be degraded in 30 min irradiation and nearly 100 % removed within 90 min. The current density could reach up to ~267.1 μA/cm²; with maximum power density (P_max) of ~16.2 μW/cm² with Rhodamine B as organic pollutant in F-HFC. The power densities were 9.0 μW/cm², 12.2 μW/cm², and 13.9 μW/cm² when using methyl orange (MO), glucose and starch as substrates, respectively. This hybrid fuel cell with BiOCl-NH₄PTA composite fulfills the purpose of decontamination of aqueous organic pollutants and synchronous electricity generation. Moreover, the novel design cell with separated photodegradation unit and the electricity generation unit could bring potential practical application in water purification and energy recovery from wastewater.     

Methanation and chemolitrophic nitrogen removal by an anaerobic membrane bioreactor coupled partial nitrification and Anammox

● Efficient carbon methanation and nitrogen removal was achieved in AnMBR-PN/A system. ● AOB outcompeted NOB in PN section by limiting aeration and shortening SRT. ● The moderate residual organic matter of PN section triggered PD in anammox unit. ● AnAOB located at the bottom of UASB played an important role in nitrogen removal. An AnMBR-PN/A system was developed for mainstream sewage treatment. To verify the efficient methanation and subsequent chemolitrophic nitrogen removal, a long-term experiment and analysis of microbial activity were carried out. AnMBR performance was less affected by the change of hydraulic retention time (HRT), which could provide a stable influent for subsequent PN/A units. The COD removal efficiency of AnMBR was > 93% during the experiment, 85.5% of COD could be recovered in form of CH₄. With the HRT of PN/A being shortened from 10 to 6 h, nitrogen removal efficiency (NRE) of PN/A increased from 60.5% to 80.4%, but decreased to 68.8% when the HRT_PN/A further decreased to 4 h. Microbial analysis revealed that the highest specific ammonia oxidation activity (SAOA) and the ratio of SAOA to specific nitrate oxidation activity (SNOA) provide stable NO₂⁻-N/NH₄⁺-N for anammox, and anammox bacteria (mainly identified as Candidatus Brocadia) enriched at the bottom of Anammox-UASB might play an important role in nitrogen removal. In addition, the decrease of COD in Anammox-UASB indicated partial denitrification occurred, which jointly promoted nitrogen removal with anammox.     

Numerical simulation of benzene transport in shoreline groundwater affected by tides under different conditions

● An approach for assessing the transport of benzene on the beach was proposed. ● The behavior of benzene in the subsurface of the beach was impacted by tide. ● Tidal amplitude influenced the travel speed and the benzene biodegradation. ● Hydraulic conductivity had the impact on plume residence time and biodegradation. ● Plume dispersed and concentration decreased due to high longitudinal dispersivity. The release and transport of benzene in coastal aquifers were investigated in the present study. Numerical simulations were implemented using the SEAM3D, coupled with GMS, to study the behavior of benzene in the subsurface of tidally influenced beaches. The transport and fate of the benzene plume were simulated, considering advection, dispersion, sorption, biodegradation, and dissolution on the beach. Different tide amplitudes, aquifer characteristics, and pollutant release locations were studied. It was found that the tide amplitude, hydraulic conductivity, and longitudinal dispersivity were the primary factors affecting the fate and transport of benzene. The tidal amplitude influenced the transport speed and percentage of biodegradation of benzene plume in the beach. A high tidal range reduced the spreading area and enhanced the rate of benzene biodegradation. Hydraulic conductivity had an impact on plume residence time and the percentage of contaminant biodegradation. Lower hydraulic conductivity induced longer residence time in each beach portion and a higher percentage of biodegradation on the beach. The plume dispersed and the concentration decreased due to high longitudinal dispersivity. The results can be used to support future risk assessment and management for the shorelines impacted by spill and leaking accidents. Modeling the heterogeneous beach aquifer subjected to tides can also be further explored in the future study.     

Relationship between groundwater cadmium and vicinity resident urine cadmium levels in the non-ferrous metal smelting area,China

● This study systematically examined the relationship between groundwater Cd and UCL. ● The study covered 211 UCL and sociological characteristic from nine groundwater samples. ● We found a significant positive correlation between groundwater Cd and UCL. ● Smoking status and education level also significantly affected UCL. Cadmium (Cd) has received widespread attention owing to its persistent toxicity and non-degradability. Cd in the human body is mainly absorbed from the external environment and is usually assessed using urinary Cd. Hunan Province is the heartland of the Chinese non-ferrous mining area, where several serious Cd pollution events have occurred, including high levels of Cd in the urine of residents. However, the environmental factors influencing high urinary Cd levels (UCLs) in nearby residents remain unclear. Therefore, 211 nearby residents’ UCLs and the corresponding sociological characteristics from nine groundwater samples in this area were analyzed using statistical analysis models. Groundwater Cd concentration ranged from 0.02 to 1.15 μg/L, aligning with class III of the national standard; the range of UCL of nearby residents was 0.37–36.60 μg/L, exceeding the national guideline of 0–2.5 μg/L. Groundwater Cd levels were positively correlated with the UCL (P < 0.001, correlation coefficient 95 % CI = 9.68, R² = 0.06). In addition, sociological characteristics, such as smoking status and education level, also affect UCL. All results indicate that local governments should strengthen the prevention and abatement of groundwater Cd pollution. This study is the first to systematically evaluate the relationship between groundwater Cd and UCL using internal and external environmental exposure data. These findings provide essential bases for relevant departments to reduce Cd exposure in regions where the heavy metal industry is globally prevalent.     

Effect of Cu-ZSM-5 catalysts with different CuO particle size on selective catalytic oxidation of N,N-Dimethylformamide

● A series of Cu-ZSM-5 catalysts were tested for DMF selective catalytic oxidation. ● Cu-6 nm samples showed the best catalytic activity and N₂ selectivity. ● Redox properties and chemisorbed oxygen impact on DMF catalytic oxidation. ● Isolated Cu²⁺ species and weak acidity have effects on the generation of N₂. N, N-Dimethylformamide (DMF), a nitrogen-containing volatile organic compound (NVOC) with high emissions from the spray industry, has attracted increasing attention. In this study, Cu-ZSM-5 catalysts with different CuO particle sizes of 3, 6, 9 and 12 nm were synthesized and tested for DMF selective catalytic oxidation. The crystal structure and physicochemical properties of the catalyst were studied by various characterization methods. The catalytic activity increases with increasing CuO particle size, and complete conversion can be achieved at 300–350 °C. The Cu-12 nm catalyst has the highest catalytic activity and can achieve complete conversion at 300 °C. The Cu-6 nm sample has the highest N₂ selectivity at lower temperatures, reaching 95% at 300 °C. The activity of the catalysts is determined by the surface CuO cluster species, the bulk CuO species and the chemisorbed surface oxygen species. The high N₂ selectivity of the catalyst is attributed to the ratio of isolated Cu²⁺ and bulk CuO species, and weak acidity is beneficial to the formation of N₂. The results in this work will provide a new design of NVOC catalytic oxidation catalysts.     

Bacteria inactivation by sulfate radical: progress and non-negligible disinfection by-products

● Status of inactivation of pathogenic microorganisms by SO₄^•− is reviewed. ● Mechanism of SO₄^•− disinfection is outlined. ● Possible generation of DBPs during disinfection using SO₄^•− is discussed. ● Possible problems and challenges of using SO₄^•− for disinfection are presented. Sulfate radicals have been increasingly used for the pathogen inactivation due to their strong redox ability and high selectivity for electron-rich species in the last decade. The application of sulfate radicals in water disinfection has become a very promising technology. However, there is currently a lack of reviews of sulfate radicals inactivated pathogenic microorganisms. At the same time, less attention has been paid to disinfection by-products produced by the use of sulfate radicals to inactivate microorganisms. This paper begins with a brief overview of sulfate radicals’ properties. Then, the progress in water disinfection by sulfate radicals is summarized. The mechanism and inactivation kinetics of inactivating microorganisms are briefly described. After that, the disinfection by-products produced by reactions of sulfate radicals with chlorine, bromine, iodide ions and organic halogens in water are also discussed. In response to these possible challenges, this article concludes with some specific solutions and future research directions.     

Cultivars and oil extraction techniques affect Cd/Pb contents and health risks in oil of rapeseed grown on Cd/Pb-contaminated farmland

● Organic solvent extracted fewer Cd/Pb in rapeseed oil than physical pressing. ● Brassica rapa transferred fewer Cd and Pb from seed to oil than Brassica napus . ● Carcinogenic risk mainly from Cd and worth more concern than noncarcinogenic risk. ● Organic solvent specially SLB pose less heath risk for oil than physical pressing. ● Rapeseed oil posed higher carcinogenic risk for rural residents than urban. Substitute planting with rapeseed offers promise for safely using large areas of Cd/Pb-contaminated farmland. Cd/Pb distributions during rapeseed oil production were investigated and health risks posed by the oil were assessed. Tests were performed using three cultivars (Brassica rapa SYH and ZS100 and Brassica napus QY-1) and four oil extraction techniques (mechanical and low-temperature pressing and n-hexane and subcritical low-temperature butane extraction). The amounts of Cd and Pb in oil were 0.73%–8.44% and 3.14%–11.76%, respectively, of the amounts in rapeseed and were strongly affected by the cultivar and oil extraction technique. The heavy metal (HM) concentrations were lower in solvent-extracted oil (particularly subcritical low-temperature butane extracted oil, in which HMs were not detected) than mechanically pressed oil. The Cd and Pb transfer indices were lower (meaning larger proportions of HMs were retained by the rapeseed meal) for B. rapa than B. napus. This was attributed to a high HM binding protein content of B. rapa seed. Health risks to humans were assessed using a probabilistic risk assessment model. The carcinogenic risk was mainly (97.1%–99.9%) caused by Cd and poses more concern than non-carcinogenic risk. Stronger health risks are posed by mechanically pressed than solvent-extracted oil, and higher carcinogenic risks are posed to people living in rural areas than urban areas. Substitute planting with B. rapa and extracting oil with organic solvent (preferably subcritical low-temperature butane) are optimal for safely utilizing Cd/Pb-contaminated soil. Attention should be paid to the health risks posed by Cd in oil to rural populations.     

Highly efficient and selective removal of phosphate from wastewater of sea cucumber aquaculture for microalgae culture using a new adsorption-membrane separation-coordinated strategy

● A new adsorption-membrane separation strategy is used for phosphate removal. ● PVC/Zr-BT shows a selective adsorption ability to low-concentration phosphate. ● Low concentration of P below 0.05 mg/L was achieved in actual wastewater treatment. ● Algal biomass production served as a demonstration of phosphorus recycling. Enhanced phosphorus treatment and recovery has been continuously pursued due to the stringent wastewater discharge regulations and a phosphate supply shortage. Here, a new adsorption-membrane separation strategy was developed for rational reutilization of phosphate from sea cucumber aquaculture wastewater using a Zr-modified-bentonite filled polyvinyl chloride membrane. The as-obtained polyvinyl chloride/Zr-modified-bentonite membrane was highly permeability (940 L/(m²·h)), 1–2 times higher than those reported in other studies, and its adsorption capacity was high (20.6 mg/g) when the phosphate concentration in water was low (5 mg/L). It remained stable under various conditions, such as different pH, initial phosphate concentrations, and the presence of different ions after 24 h of adsorption in a cross-flow filtration system. The total phosphorus and phosphate removal rate reached 91.5% and 95.9%, respectively, after the membrane was used to treat sea cucumber aquaculture wastewater for 24 h and no other water quality parameters had been changed. After the purification process, the utilization of the membrane as a new source of phosphorus in the phosphorus-free f/2 medium experiments indicated the high cultivability of economic microalgae Phaeodactylum tricornutum FACHB-863 and 1.2 times more chlorophyll a was present than in f/2 medium. The biomass and lipid content of the microalgae in the two different media were similar. The innovative polyvinyl chloride/Zr-modified-bentonite membrane used for phosphorus removal and recovery is an important instrument to establish the groundwork for both the treatment of low concentration phosphate from wastewater as well as the reuse of enriched phosphorus in required fields.     

Electro-conductive crosslinked polyaniline/carbon nanotube nanofiltration membrane for electro-enhanced removal of bisphenol A

● A crosslinked polyaniline/carbon nanotube NF membrane was fabricated. ● Electro-assistance enhanced the removal rate of the NF membrane for bisphenol A. ● Intermittent voltage-assistance can achieve nearly 100% removal of bisphenol A. ● Membrane adsorption–electro-oxidation process is feasible for micropollutant removal. Nanofiltration (NF) has attracted increasing attention for wastewater treatment and potable water purification. However, the high-efficiency removal of micropollutants by NF membranes is a critical challenge. Owing to the adsorption and subsequent diffusion, some weakly charged or uncharged micropollutants, such as bisphenol A (BPA), can pass through NF membranes, resulting in low removal rates. Herein, an effective strategy is proposed to enhance the BPA removal efficiency of a crosslinked polyaniline/carbon nanotube NF membrane by coupling the membrane with electro-assistance. The membrane exhibited a 31.9% removal rate for 5 mg/L BPA with a permeance of 6.8 L/(m²·h·bar), while the removal rate was significantly improved to 98.1% after applying a voltage of 2.0 V to the membrane. Furthermore, when BPA coexisted with humic acid, the membrane maintained 94% removal of total organic carbon and nearly 100% removal of BPA at 2.0 V over the entire filtration period. Compared to continuous voltage applied to the membrane, an intermittent voltage (2.0 V for 0.5 h with an interval of 3.5 h) could achieve comparable BPA removal efficiency, because of the combined effect of membrane adsorption and subsequent electrochemical oxidation. Density functional theory calculations and BPA oxidation process analyses suggested that BPA was adsorbed by two main interactions: π–π and hydrogen-bond interactions. The adsorbed BPA was further electro-degraded into small organic acids or mineralized to CO₂ and H₂O. This work demonstrates that NF membranes coupled with electro-assistance are feasible for improving the removal of weakly charged or uncharged micropollutants.