Formation of chloroform and carbon tetrachloride in foods treated with sodium hypochlorite

The formation of chloroform and carbon tetrachloride during the treatment of fresh vegetable homogenate with sodium hypochlorite was studied.When a n-hexane extract of the reaction mixture of fresh vegetables and sodium hypochlorite was analysed by gas chromatography, chloroform and carbon tetrachloride were detected, and many unidentified peaks were also observed. The formation conditions of chloroform and carbon tetrachloride were studied. The mechanism of chloroform formation may be different from that of carbon tetrachloride according to the study of pH on the formation of both compounds. The formation of chloroform is much greater than that of carbon tetrachoride.     

Mechanism for the destruction of carbon tetrachloride and chloroform DNAPLs by modified Fenton's reagent

The destruction of a carbon tetrachloride DNAPL and a chloroform DNAPL was investigated in reactions containing 0.5 mL of DNAPL and a solution of modified Fenton's reagent (2M H2O2 and 5mM iron(III)-chelate). Carbon tetrachloride and chloroform masses were followed in the DNAPLs, the aqueous phases, and the off gasses. In addition, the rate of DNAPL destruction was compared to the rate of gas-purge dissolution. Carbon tetrachloride DNAPLs were rapidly destroyed by modified Fenton's reagent at 6.5 times the rate of gas purge dissolution, with 74% of the DNAPL destroyed within 24h. Use of reactions in which a single reactive oxygen species (hydroxyl radical, hydroperoxide anion, or superoxide radical anion) was generated showed that superoxide is the reactive species in modified Fenton's reagent responsible for carbon tetrachloride DNAPL destruction. Chloroform DNAPLs were also destroyed by modified Fenton's reagent, but at a rate slower than the rate of gas purge dissolution. Reactions generating a single reactive oxygen species demonstrated that chloroform destruction was the result of both superoxide and hydroxyl radical activity. Such a mechanism of chloroform DNAPL destruction is in agreement with the slow but relatively equal reactivity of chloroform with both superoxide and hydroxyl radical. The results of this research demonstrate that modified Fenton's reagent can rapidly and effectively destroy DNAPLs of contaminants characterized by minimal reactivity with hydroxyl radical, and should receive more consideration as a DNAPL cleanup technology.     

Pathways and kinetics of carbon tetrachloride and chloroform reductions by nano-scale Fe and Fe/Ni particles: comparison with commercial micro-scale Fe and Zn

Groundwater and wastewater contaminated with chlorinated organic compounds (COCs) can be treated with zero-valent metals. The practicality of this treatment method depends on the reduction rates of the target compounds and their byproducts. In this study, nano-scale Fe and Fe/Ni particles were synthesized so that they could be used to rapidly degrade carbon tetrachloride (CT) and chloroform (CF). Their BET surface areas were around two orders higher than those of commercial micro-scale Fe and Zn particles. Batch reduction experiments carried out with a metal loading of 2.5 gl(-1) showed that complete reduction of CT by the nano-scale Fe/Ni and Fe particles could be achieved within 20 min and 60 min, respectively. With the commercial micro-scale Fe and Zn particles applied at 125 gl(-1), complete CT reduction could only be achieved after 4h and 1.5h, respectively. Reductions of CT and CF with the nano-scale particles followed pseudo-first-order kinetics, and the specific reaction rate constants with the nano-scale Fe/Ni particles were 2-8 times higher than those of the nano-scale Fe particles. CT was degraded through hydrogenolysis to CF, and subsequently via both complete reduction pathway to methane and hydrogenolysis pathway to dichloromethane (DCM). Significantly more methane was generated with the use of the nano-scale Fe/Ni particles than with the nano-scale Fe particles. While the commercial Zn particles were more reactive than the commercial Fe particles, they failed to transform CT directly into methane, causing accumulation of DCM in the aqueous phase.     

四氯化碳的生产与应用及其淘汰策略

四氯化碳是一种消耗臭氧层物质,其生产和消费都面临着严峻的淘汰形势.简要叙述了四氯化碳的生产技术,以四氯化碳为原料生产大宗化学品和精细化学品的转化技术,四氯化碳作为化工助剂在我国的应用情况以及相应的淘汰方法和技术进展.     

四氯化碳的生产与应用及其淘汰策略

四氯化碳是一种消耗臭氧层物质，其生产和消费都面临着严峻的淘汰形势。简要叙述了四氯化碳的生产技术，以四氯化碳为原料生产大宗化学品和精细化学品的转化技术，四氯化碳作为化工助剂在我国的应用情况以及相应的淘汰方法和技术进展。     

Bimetallic iron-aluminum particles for dechlorination of carbon tetrachloride

Bimetallic iron-aluminum (Fe/Al) particles were synthesized and tested for their reactivity toward carbon tetrachloride using batch reactors and a flow-through column at near neutral pH. Preparation of bimetallic Fe/Al particles was conducted under acidic conditions under which iron was readily deposited onto the aluminum surface. The SEM image showed clusters of iron on the aluminum surface at the measured Fe:Al molar ratio of about 2:3. Results showed that the presence of zero-valent aluminum successfully prevented the formation of a passive layer at the iron surface and maintained the reactivity of iron. The dechlorination of carbon tetrachloride by bimetallic Fe/Al particles produced chloroform (9%), dichloromethane (17%) and methane (38%). Kinetic analysis suggests that bimetallic Fe/Al particles increased the reactivity toward carbon tetrachloride degradation by a factor of 10 compared to zero-valent iron and possessed a comparable reactivity with nano-sized Fe. The effectiveness of bimetallic Fe/Al particles was further confirmed by the continuous flow column study from which an ageing of bimetallic particles was also observed.     

纳米级铁粉脱氯降解四氯化碳

四氯化碳的生产和使用,给人类带来了较大危害.为此,采用纳米铁粉这一新方法对其进行脱氯处理.试验以纳米级铁粉对四氯化碳的脱氯率为考察指标,选用L25(56)正交试验方案,考察了降解介质的初始pH值、纳米铁粉的质量、降解温度、摇床转速和脱氯时间5个影响因素.结果表明,pH值这一因素有极显著影响;在得出的纳米铁粉对四氯化碳脱氯的最佳工艺条件下,获得了99.5%的脱氯率,为有机氯化物脱氯开辟了一条新途径.     

纳米级铁粉脱氯降解四氯化碳

四氯化碳的生产和使用，给人类带来了较大危害。为此，采用纳米铁粉这一新方法对其进行脱氯处理。试验以纳米级铁粉对四氯化碳的脱氯率为考察指标，选用L25（5^6）正交试验方案，考察了降解介质的初始pH值、纳米铁粉的质量、降解温度、摇床转速和脱氯时间5个影响因素。结果表明，pH值这一因素有极显著影响；在得出的纳米铁粉对四氯化碳脱氯的最佳工艺条件下，获得了99．5％的脱氯率，为有机氯化物脱氯开辟了一条新途径。     

Degradation of carbon tetrachloride in the presence of iron and sulphur containing compounds

The effect of several sulphur compounds: sodium sulphate, sodium sulphide, ferrous sulphide,pyrite and an organosulphonic acid on the kinetics of the iron (Fe °) induced degradation of carbon tetrachloride was examined under aerobic conditions. It was observed that all of the sulphur compounds investigated significantly accelerated the reaction. The mechanisms of the processes studied as well as their possible influence on the efficiency of the iron-induced dehalogenation of pollutants, both in situ and in above-ground treatment are discussed.     

Effect of carbon tetrachloride on sonochemical decomposition of methyl orange in water

Two types of sonicators were used for the sonochemical decomposition of methyl orange (MO) in the presence and absence of carbon tetrachloride (CCl4): One is a 45kHz ultrasonic cleaning bath (a low intensity sonicator) and the other is a 200kHz ultrasonic reactor (a high intensity sonicator). It was clearly confirmed that the rates of the sonochemical decomposition of MO increased with increasing the concentration of CCl4 in both sonicators. The enhancement effect of CCl4 was much higher in the high intensity sonicator than in the low intensity one: by the addition of 100ppm of CCl4, the decomposition ratio of MO with the high intensity sonicator became 41 times larger, while that with the low intensity sonicator became 4.8 times larger. Based on the obtained results, it was suggested that the formed cavitation phenomenon was different between sonicators. It was also suggested that the sonochemical decomposition of MO in the presence of CCl4 would be useful to evaluate the sonochemical efficiency, because the rate of MO decomposition can be effectively enhanced by the sonolysis of CCl4.     

某市南郊水源地土壤四氯化碳污染特征

含四氯化碳废水在排放的过程中沿排污渠侧壁和底部的渗漏对土壤造成污染.在对某市南郊受四氯化碳污染的水源地进行钻孔检测的过程中发现,土壤四氯化碳污染的特征:靠近排污沟的钻孔均检测出四氯化碳,而远离排污沟的钻孔则未检出;四氯化碳的垂向分布存在不连续性,且受降雨影响较大;大部分钻孔浅层土壤中基本未检测到四氯化碳,而在3 m以下的土层和基岩中检测到四氯化碳;抽水井的抽水行为导致抽水井附近土壤中四氯化碳明显高于其他钻孔点位检测结果.     

The spatial distribution of eubacteria and archaea in sand-clay columns degrading carbon tetrachloride and methanol

The spatial distribution of microbial communities was investigated in anaerobic sand-clay columns fed methanol and carbon tetrachloride (CT). Microbial communities were characterized through analysis of soil samples with denaturing gradient gel electrophoresis (DGGE) and quantitative polymerase chain reaction (qPCR) for archaea and eubacteria. Increasing CT inlet concentrations to 29 microM lead to complete inhibition of methanol consumption in both columns. Although low levels of eubacteria and archaea were initially present in the clay soils in both columns, there was no significant microbial growth over 400 days in the clays beyond the interface with the sand zone. Thus, the potential for increased contaminant attenuation in heterogeneous sand-clay systems through biodegradation in the clay matrix zones may be limited in many systems.     

Degradation of aqueous carbon tetrachloride by nanoscale zerovalent copper on a cation resin

Nanoscale zerovalent copper supported on a cation resin was successfully synthesized to enhance the removal of carbon tetrachloride (CCl(4)) from contaminated water. The use of the cation resin as a support prevents the reduction of surface area due to agglomeration of nanoscale zerovalent copper particles. Moreover, the cation resin recycles the copper ions resulting from the reaction between CCl(4) and Cu(0) by simultaneous ion exchange. The decline in the amount of CCl(4) in aqueous solution results from the combined effects of degradation by nanoscale zerovalent copper and sorption by the cation resin; thus the amount of CCl(4) both in aqueous solution and sorbed onto the resin were measured. The pseudo-first-order rate constant normalized by the surface-area and the mass concentration of nanoscale zerovalent copper (k(SA)) was 2.1+/-0.1 x 10(-2)lh(-1)m(-2), approximately twenty times that of commercial powdered zerovalent copper (0.04 mm). Due to the exchange between Cu(2+) and the strongly acidic ions (H(+) or Na(+)), the pH was between 3 and 4 in unbuffered solution and Cu(2+) at the concentration of less than 0.1 mg l(-1) was measured after the dechlorination reaction. In the above-ground application, resin as a support would facilitate the development of a process that could be designed for convenient emplacement and regeneration of porous reductive medium.     

Protective effects of seaweeds against liver injury caused by carbon tetrachloride in rats

Three species of seaweeds collected from Tung Ping Chau, Hong Kong, were screened for their hepatoprotective activity using carbon tetrachloride (CCl4)-induced liver injury in the rat as a model of chemical hepatitis. A single oral dose of 1.25 ml/kg of CCl4 was able to produce significantly elevated levels of serum glutamic pyruvic transaminase (GPT) and glutamic oxaloacetic transminase (GOT). Administration of 150, 300 and 600 mg/kg of aqueous extracts from Myagropsis myagroides, Sargassum henslowianum and S. siliquastrum, respectively, significantly reduced the CCl4-induced acute elevation in the levels of GPT and GOT in rats. The same result was also seen in the histopathological study of liver tissue. The seaweed crude extracts probably acted to protect against CCl4-induced liver injury through their antioxidant properties.     

Transformation of carbon tetrachloride by bisulfide treated goethite, hematite, magnetite, and kaolinite

This study investigated the transformation of carbon tetrachloride (CT) by goethite, hematite, magnetite, and kaolinite treated with bisulfide to form coatings of iron monosulfide (FeS) and other Fe(II) species. These coatings contribute to abiotic natural attenuation in anaerobic environments. Batch kinetic experiments were performed under anoxic conditions at pH 8.0. Surface-area-normalized pseudo-first-order rate constants for CT transformation did not differ significantly for the three HS- treated iron oxides, but the rate of CT transformation by bisulfide-treated kaolinite was significantly lower, most likely due to kaolinite's lower iron content. The yield of chloroform (CF) from CT transformation was typically approximately 1%. There was negligible or only slight adsorption of several natural organic matter (NOM) model compounds to the surface of HS- treated goethite, and these compounds had no influence on CT transformation rate constants or CF yields. Juglone, on the other hand, adsorbed to a greater extent, and also significantly influenced the CF yield, increasing it by a factor of approximately 20 for HS- treated hematite. We speculate that juglone or its HS- addition product adsorbed to the mineral surface and acted as a hydrogen atom donor that reacted with the trichloromethyl radical intermediate, increasing the CF yield.     

Flow behavior and residual saturation formation of liquid carbon tetrachloride in unsaturated heterogeneous porous media

The formation of residual, discontinuous nonaqueous phase liquids (NAPLs) in the vadose zone is a process that is not well understood. To obtain data that can be used to study the development of a residual NAPL saturation in the vadose zone and to test current corresponding models, detailed transient experiments were conducted in intermediate-scale columns and flow cell. The column experiments were conducted to determine residual carbon tetrachloride (CCl(4)) saturations of two sands and to evaluate the effect of CCl(4) vapors on the water distribution. In the intermediate-scale flow cell experiment, a rectangular zone of the fine-grained sand was packed in an otherwise medium-grained matrix. A limited amount of CCl(4) was injected from a small source and allowed to redistribute until a pseudo steady state situation had developed. A dual-energy gamma radiation system was used to determine fluid saturations at numerous locations. The experiments clearly demonstrated the formation of residual CCl(4) saturations in both sands. Simulations with an established multifluid flow simulator show the shortcomings of current relative permeability-saturation-capillary pressure (k-S-P) models. The results indicate that nonspreading behavior of NAPLs should be implemented in simulators to account for the formation of residual saturations.     

Synthesis of hybrid carbon nanotubes using Brassica juncea L. application to photodegradation of bisphenol A

Hyperaccumulators contain tubular cellulose and heavy metals, which can be used as the sources of carbon and metals to synthesize nanomaterials. In this paper, carbon nanotubes (CNTs), Cu_0.05Zn_0.95O nanoparticles, and CNTs/Cu_0.05Zn_0.95O nanocomposites were synthesized using Brassica juncea L. plants, and the ultraviolet (UV)-light-driven photocatalytic degradations of bisphenol A (BPA) using them as photocatalysts were studied. It was found that the outer diameter of CNTs was around 50 nm and there were a few defects in the crystal lattice. The synthesized Cu_0.05Zn_0.95O nanocomposites had a diameter of around 40 nm. Cu_0.05Zn_0.95O nanocomposites have grown on the surface of the CNTs and the outer diameter of them was around 100 nm. The synthesized hybrid carbon nanotubes using B. juncea could enhance the efficiency of photocatalytic degradation on BPA. The complete equilibration time of adsorption/desorption of BPA onto the surface of CNTs, Cu_0.05Zn_0.95O nanoparticles, and CNTs/Cu_0.05Zn_0.95O nanocomposites was within 30, 20, and 30 min, and approximately 14.9, 8.7, and 17.4 % BPA was adsorbed by them, respectively. The combination of UV light irradiation (90 min) with CNTs, Cu_0.05Zn_0.95O nanoparticles, and CNTs/Cu_0.05Zn_0.95O nanocomposites could lead to 48.3, 75.7, and 92.6 % decomposition yields of BPA, respectively. These findings constitute a new insight for synthesizing nanocatalyst by reusing hyperaccumulators.     

Modeling VOCs adsorption onto activated carbon

The activated carbon adsorption process is affected by the characteristics of adsorbent, adsorbate and environmental conditions. In this study, both adsorption and desorption processes are assumed to occur simultaneously and a numerical model was developed with a non-linear driving force in conjunction with the Langmuir model for predicting the overall adsorption process. The numerical model provides both adsorption and desorption rate constants and activation energies. The resultant equilibrium constants are of the same order of magnitude as reported by other studies. Results show that the model could well predict the adsorption isotherms and breakthrough curves under various conditions.     

Chlorination of p-cymene by chlorine in carbon tetrachloride: Model compounds for environmental analyses

p-Cymene was chlorinated by chlorine in CCl₄. The products of the chlorination were separated by distillation and purified by preparative gas chromatography. The structures of chlorocompounds were confirmed by means of their NMR and mass spectra. The distillation gave as the main compounds: (2) 2-chloro-, (4) 2,3-dichloro-, (5) 2,5-dichloro-, (6) 2,3,6-trichloro-, (7) 2,3,5,6-tetrachloro-p-cymenes and as by-products: (8) 2,5,7-trichloro-p-cymene, (9) 2,6-dichloro-1-methyl-4-(1-methylethenyl)benzene (cymenene), and (10) 2,3,6-trichloro-1-methyl-4-(1-methylethenyl)benzene (cymenene).