载Ca磁性碳纳米管对水中腐殖酸的去除

采用化学共沉淀一步法以钙盐和铁盐对多壁碳纳米管（MWCNTs）改性以制备具有去除水中微污染物腐殖酸的磁性碳纳米管复合材料。X射线能谱分析表明改性MWCNTs上载有Ca和Fe元素。通过振动样品磁强计测得该复合材料具有较强磁性。改性后的MWCNTs 30 min对水中腐殖酸的去除率由改性前的63.89%提高到90.27%。研究了改性MWCNTs投加量、腐殖酸初始浓度、吸附时间、振荡速度、pH及温度对水中腐殖酸去除的影响。结果表明,腐殖酸去除率随着载Ca磁性MWCNTs投加量增大而提高。吸附量随着腐殖酸初始浓度的增大而增加,但去除率却减小。吸附初期腐殖酸去除速率快,0.5 g·L-1的载Ca磁性多壁碳纳米管在腐殖酸初始浓度为20 mg·L-1时,5 h达到吸附平衡,平衡吸附量为39.41 mg·g-1。腐殖酸去除率随着振荡速度的增大而增大,在225 r·min-1时达最大,随后随着振荡速度的增大而缓慢下降。在弱酸性下,腐殖酸去除率较高,当pH为5时,腐殖酸去除率达到92.24%;当pH5时,腐殖酸去除率随pH增大呈下降趋势。腐殖酸去除率随着温度的升高而降低。     

Phototransformation of ibuprofen and ketoprofen in aqueous solutions

The UV (254 nm) and UV/VUV (254/185 nm) photolysis of two anti-inflammatory drugs, ibuprofen and ketoprofen, have been studied in aqueous solutions as a possible process for the removal of non-biodegradable compounds.We have examined the effects of dissolved oxygen and initial target concentration. Upon irradiation at 254 nm, the decomposition rate of ketoprofen is almost forty times higher as it of ibuprofen whilst VUV irradiation only increased the ibuprofen decomposition rate. The presence of dissolved oxygen accelerated the photodegradation of ibuprofen, whereas no effect was observed on the degradation of ketoprofen. The maximum quantum yield for the phototransformation was 0.2. The rate of mineralization in both cases was ∼60%, even after 1 h of treatment and this suggests the formation of stable by-products which were identified using GC-MS and HPLC-MS, respectively.     

Gross fluxes of methyl chloride and methyl bromide in a California oak-savanna woodland

Temperate woodland ecosystems are believed to be both a source and sink for atmospheric methyl bromide and methyl chloride. To separate the gross production and consumption fluxes in this ecosystem, we applied a stable isotope tracer technique in field and laboratory-based experiments. Flux measurements were conducted in a California oak-savanna woodland ecosystem at several intervals throughout the day during the wet and dry seasons to observe the diurnal and seasonal variability of fluxes. While gross production was small and variable, gross consumption showed a clear difference between seasons, with much larger rates during the wet season and negligible rates during the dry season. Laboratory incubations confirmed that fluxes were strongly affected by soil moisture. Consumption rates of methyl bromide, however, are less than half of the previous estimates of temperate woodland soil uptake rates during the growing season. Nevertheless, woodlands cover a significant portion of the world's land surface area and may still be an important component of the soil sink for these methyl halides.     

Abiotic transformation of DDT in aqueous solutions

Significant concentrations of chlorinated pesticides such as 1,1,1-trichloro-2,2-bis(4-chlorophenyl)ethane (DDT) and its two main transformation products, 1,1-dichloro-2,2-bis(4-chlorophenyl)ethane (DDD) and 1,1-dichloro-2,2-bis(4-chlorophenyl)ethylene (DDE) are still present in soil and sediment systems more than 30 years after DDT use was banned in the United States. DDT enters waterways via the runoff from industrial point sources, agricultural lands and atmospheric deposition. We evaluated zero-valent iron (Fe(0)), ferrous sulfide (FeS), as well as combining them with hydrogen peroxide (H(2)O(2)) as viable treatment technologies for degrading DDT in an aqueous solution. Treatment of DDT with Fe(0) and FeS resulted in approximately 88% and 56% transformation of DDT within 150h, respectively. DDE production was insignificant in all systems. The DDT removal was slower with FeS than with Fe(0), but the amounts of DDD and DDE produced did not exceed baseline. Treatment with a 1:1 mixture of Fe(0)-FeS removed about 95% of the added mass of DDT within 4days and generated significant amounts of DDD and minor amounts of DDMU. When small amounts of H(2)O(2) were introduced halfway through the Fe(0) and FeS treatment times, the mass of DDT decreased by 87% and 96%, respectively, within 2days. Our results demonstrate that mixtures of Fe(0)-FeS in combination with H(2)O(2) can be used for rapid and efficient removal of DDT from aqueous solutions.     

Photocatalytic degradation of microcystin-LR in aqueous solutions

In this work, the photocatalytic degradation of aqueous microcystin-LR was studied using TiO₂ and ZnO as photocatalysts. The process was optimised and characterised at the bench scale (200 mL); both semiconductors exhibited a high degradation capacity at reaction times of 1 min (degradation greater than 95%). The transient species that were observed indicate that the degradation occurs via the multiple hydroxylation and elimination of the labile peptide residues of the molecule. When photocatalysis was applied in a continuous treatment system (20–50 L), the photocatalytic process exhibited a high degradation efficiency, which resulted in residual microcystin-LR concentrations that were less than 1 μg L^?1 (C₀ = 5 μg L^?1).     

Photocatalytic degradation of molinate in aqueous solutions

In this study, the degradation of molinate through heterogeneous photocatalysis, using two different types of the semiconductor TiO₂ as photocatalyst, as well as through homogeneous treatment, applying the photo-Fenton reaction, has been investigated. As far as heterogeneous photocatalysis is concerned, the degradation of the pesticide follows apparent first-order kinetics, while the type of the catalyst and the pH value of the solution affect the degradation rate. The effect of the addition of electron scavengers (H₂O₂ and K₂S₂O₈) was also studied. In the case of photo-Fenton-assisted system, the degradation also follows pseudo-first-order kinetics. Parameters such as iron’s and electron scavenger’s concentration and inorganic ions strongly affect the degradation rate. The extent of pesticide mineralization was investigated using dissolved organic carbon (DOC) measurements. The toxicity of the treated solution was evaluated using the Microtox test based on the luminescent bacteria Vibrio fischeri. The detoxification and mineralization efficiency was found to be dependent on the system studied, and although it did not follow the rate of pesticide disappearance, it took place in considerable extent. The study of the photodegradation treatment was completed by the determination of the intermediate by-products formed during the process, which was carried out using LC-MS/MS technique and led to similar compounds with both processes.     

Photochemical transformation of azoxystrobin in aqueous solutions

The photochemical behaviour of azoxystrobin fungicide (AZX) in water was studied under laboratory conditions. Photodegradation was initiated using a solar simulator (xenon arc lamp) or a jacketed Pyrex reaction cell equipped with a 125 W, high-pressure mercury lamp. HPLC/MS analysis (APCI and ESI in positive and negative modes) was used to identify AZX photoproducts. The calculated polychromatic quantum efficiencies (phi) of AZX at pH 4.5, 7 and 9 were 5.42 x 10(-3), 3.47 x 10(-3) and 3.06 x 10(-3) (degraded molecules per absorbed photon), respectively. The relatively narrow range of values indicates the stability of AZX with respect to photodegradation in the studied pH range. Results from the HPLC/MS analysis suggest that the phototransformation of AZX proceeds via multiple, parallel reaction pathways including: (1) photo-isomerization (E-->Z), (2) photo-hydrolysis of the methyl ester and of the nitrile group, (3) cleavage of the acrylate double bond, (4) photohydrolytic ether cleavage between the aromatic ring giving phenol, and (5) oxidative cleavage of the acrylate double bond.     

Polychlorodibenzo-p-dioxins and dibenzofurans in technical pentachlorophenol - results of a collaborative analytical exercise

Results of analyses of eight samples of technical pentachlorophenol conducted by three different analytical methods are presented and discussed.     

Duckweed (Lemna gibba) growth inhibition bioassay for evaluating the toxicity of olive mill wastes before and during composting

Two-phase olive mill waste (TPOMW) is considered the main problem confronting the modern oil extraction and processing industry. Composting has been recently proposed as a suitable method to treat TPOMW so that it is suitable for use in agriculture. In the work reported here, the Lemna gibba bioassay was tested to assess the toxicity of TPOMW before and during the composting process. The method was compared with the Lepidium sativum bioassay and with other chemical maturity indices traditionally reported in the literature. The L. gibba test proved to be a simple, sensitive, and accurate method to evaluate toxicity before and during the composting of TPOMW. Plant growth response was measured by two methods: counting the number of fronds (leaves) and measuring total frond area (TFA) with image analysis software. Compared to the counting of fronds (L. gibba) or seeds (L. sativum), the use of area-measuring software permitted a very rapid, unbiased and easy way of analysing the toxicity of TPOMW before and during composting. Although the accuracy of the frond count method was similar to the traditional cress seed test, data analysis showed that the TFA measurement method was statistically more accurate (significantly lower variance) than the frond count approach. Highly significant correlations were found between TFA and some important maturation indices commonly reported in literature indicating that the L. gibba bioassay can be a useful tool to determine the degree of maturity of TPOMW composts.     

Photo-fenton assisted reaction of dimethoate in aqueous solutions

The photo-Fenton reaction of an organophosphorus insecticide, dimethoate (O,O-dimethyl methylcarbamoylmethyl phosphorodithioate), was studied by following the identification and determination of the decomposition products and the total carbon removal rate. The reactions were performed in a batch recycle reactor, at room temperature, using UV radiation, H2O2 as oxidant, and FeCl3 x 6H2O as catalyst. The oxidation results were determined with a total organic carbon (TOC) analyzer and ion chromatography. The presence of reaction products was identified by gas chromatography-mass spectrometry (GC-MS). Apart from the sulfate, phosphate, and ammonium ions, the presence of dimethyl phosphite, N-methyl-acetamide, and formic acid was also detected. Excess of H2O2 concentration did not influence the reaction rate. The expression for the total carbon removal was assessed and the TOC removal rate constants were calculated.     

Electrochemical oxidation of sulfite ions in aqueous solutions

Gaseous pollutants that affect human health, destroy vegetation and damage materials and art treasures can be converted into harmless components by electrochemical reactions. Electrochemical gas purification methods can be applied basically in two steps. In the first step, gases to be removed are absorbed in an aqueous electrolyte. Then, in the second step, they can be converted into harmless components via electrochemical oxidation or electrochemical reduction. This study investigated the feasibility of electrochemical removal of sulfite ions arising from the absorption of sulfur dioxide in an aqueous electrolyte. The removal efficiency, current efficiency, and energy consumption were determined at different initial sulfite ion and electrolyte concentrations and applied currents. Furthermore, linear sweep voltammetry studies were performed using a graphite electrode in sulfuric acid. It has been concluded from all these experiments that sulfur dioxide can successfully be removed using an electrochemical method.     

Radiation-induced degradation of methyl orange in aqueous solutions

Degradation of methyl orange under gamma-irradiation was investigated. The reactions followed pseudo first-order kinetics. Apparent degradation rate constant, estimated through linear regression analysis, increased with an increase of dose rate and a decrease of initial methyl orange concentration. Degradation of methyl orange was significantly accelerated under oxidative condition, but was slightly enhanced under reductive condition. However, the result of decoloration was better under reductive condition than oxidative one. An analysis on the intermediates using Fourier transform infrared and gas chromatography/mass spectrometry demonstrates that the radiolytic degradation of methyl orange was processed with different C-N cleavages under oxidative and reductive conditions.     

Ferric citrate-induced photodegradation of dyes in aqueous solutions

The photooxidation of dye solutions containing Fe(III)-citrate complexes was studied. The photodegradation under near-UV light of the five dyes, C. I. reactive red 2, C. I. reactive blue 4, C. I. reactive black 8, C. I. basic red 13 and C. I. basic yellow 2, in aqueous solutions at pH2.0 containing Fe(III)-citrate complexes was found to follow pseudo-first order kinetics. The photodegradation rates of the dye, C. I. reactive red 2, decreased with increasing the initial dye concentration in range of 20 – 60 mg/L . A comparatively higher photodegradation efficiency of the dye was gained under the condition of pH2.0 and the Fe(III) to citrate ratio 1:2.     

Behavior and stability of organic contaminant droplets in aqueous solutions

The behavior of several hydrophobic organic compounds (HOCs) in water at concentrations close to and above their maximum solubility values was studied. For this purpose, solutions of benzene, toluene, xylene, trichloroethylene (TCE) and a mixture of them were prepared in excess in freshwater and in saltwater, and solution stability was examined. High organic concentrations were found to remain stable in both freshwater and saltwater. In saltwater, for example, toluene and xylene concentrations remained as high as 14 and 26 times their solubilities, respectively, over a period of 6 days, while in freshwater, their concentrations remained 8 and 30 times their solubilities over the same period. This phenomenon is attributed to the presence of stable organic droplets, which were observed using optical microscopy. In addition, the transport of HOC droplets through sand is demonstrated, using an experimental system consisting of a saltwater source reservoir connected by a porous inactive sand layer to a freshwater collector reservoir.     

超声波降解水溶液中对二氯苯

采用超声波降解含对二氯苯(p-DCB)的溶液,研究了p-DCB降解的动力学和影响因素.结果表明:(1)超声波降解水溶液中的p-DCB,随着p-DCB初始浓度的增加降解率减小;p-DCB的超声波降解反应符合表观一级动力学规律.(2)增大超声波频率和功率以及双频率联合使用可以增大p-DCB的降解率和一级反应速率常数.(3)弱酸性或中性环境更有利于p-DCB的降解进行.(4)反应时的搅拌和自由基清除剂的投加都降低了p-DCB的降解率,这是因为超声波降解时空化气泡内的热裂解和自由基作用的削弱.(5)在单一体系中,p-DCB比对氯苯胺(p-ClA)更易降解.在混合体系中,p-ClA的加入没有显著降低p-DCB的去除效果,因为亲水的p-ClA不易挥发,难以进入空化气泡竞争能量和自由基,其存在对空化气泡内混合气体的比热容比影响较小;而p-DCB的存在却明显降低了p-ClA的降解效果,因为疏水的p-DCB易挥发进入空化气泡竞争能量和自由基,并降低混合气体的比热容比.     

超声波-空气体系对溶液中五氯酚的降解

以五氯酚(PCP)为目标污染物,研究了超声波-空气体系对PCP降解的可行性和降解特性。溶液温度和初始pH对五氯酚吹脱作用实验表明,在弱酸性和碱性条件下空气对五氯酚基本无吹脱作用;空气流量、初始pH、温度、反应物浓度等因素对超声波-空气体系降解五氯酚的影响实验表明,当空气流量为25 mL·min-1,pH=5时,去除效果最优,低温、低浓度有利于五氯酚降解;考察了5种常见金属离子对强化降解五氯酚的影响,其强化作用顺序依次为Fe2+ > Cu2+ > Al3+ > Zn2+ > CK > Mg2+(CK为空白),Fe2+与体系之间存在协同效应;降解机理研究表明,体系对五氯酚的降解以自由基氧化作用为主,H2O2氧化为辅,空气的加入能明显促进H2O2的产生,加入Fe2+后,H2O2与之反应生成·OH,导致H2O2含量急剧减少。     

水中安替比林的紫外光降解研究

以波长为254 nm的紫外杀菌灯为光源,研究了水溶液中消炎镇痛药物安替比林（PZ）的光降解行为;考察了初始pH值及水中其他物质对PZ光降解的影响,探讨了PZ光解机制,并分析其降解产物及光解途径。结果表明,安替比林的光降解遵循拟一级反应动力学规律,pH值变化对光解速率基本没有影响。安替比林直接光降解占主导作用,活性氧类物种（ROS）对安替比林间接光解基本没有贡献。腐殖酸对安替比林光降解有抑制作用,而NO^-₃,HCO^-₃,Cl^-对安替比林光降解没有明显作用。GC-MS分析表明安替比林在紫外辐射下生成甲酰胺,乙酰胺,2-羟基吲哚-3-酮,2,4（1氢,3甲基）-喹唑啉二酮,1-甲基-2-羟基苯并咪唑,2-羟基苯并恶唑等一系列具有安替比林母体苯环结构的化合物,表明安替比林侧链上N—N键断裂导致其最终降解。     

Biodegradation of technical mixtures of oxyethylenated aliphatic alcohols in an aqueous environment

A study of the biodegradability of nonionogenic surfactants of oxyethylenated n-butyl, isobutyl, n-pentyl and isopentyl alcohols was conducted by modified static test according to International Standard Organization method 9888. Degradation was evaluated by changes in concentrations of individual oligomers, ethylene glycols, carboxylic and dicarboxylic acids. Good biological degradability was found, with a "primary" degradability of 75-98% in 10 days. Obtained results, in agreement with our previous work, proved the dominant proportion of degradative scission in the hydrophile part of surfactant molecule. During biological degradation no significant cumulation of mono- to polyethylene glycols appeared neither that of mono- or dicarboxylic acids, and degradation of these components was not a rate-determining degradation factor.