直接红染料的臭氧脱色与中间产物研究

以直接红B模拟染料废水为研究对象,考察了臭氧化过程中染料溶液的吸光度和TOC的变化,同时利用离子色谱仪和GC/MS对染料的降解过程进行了分析,最后用发光细菌法检测了染料溶液急性毒性的变化。结果表明,臭氧对染料的降解符合一级反应动力学,20 min时对染料的脱色率达到99.2%;反应40 min后TOC减少32.55%,染料分子有97.8%的S被氧化为SO^2-₄,偶氮键被臭氧化为N₂,分子中的仲胺基小部分转化成游离NH⁺₄和NO^-₃;在臭氧化过程前期新生成的醛类和酰胺类物质使溶液急性毒性迅速上升,25 min后溶液毒性开始逐渐下降。     

Ozonation of Cationic Red X-GRL in aqueous solution: degradation and mechanism

Ozonation of the azo dye Cationic Red X-GRL was investigated in a bubble column reactor at varying operating parameters such as oxygen flow rate, temperature, initial Cationic Red X-GRL concentration, and pH. The conversion of dye increased with the increasing of pH and oxygen flow rate. As the reaction rate constant and the volumetric mass transfer coefficient increase while the ozone equilibrium concentration decreases with the temperature, there is a minimum conversion of dye at 25 degrees C. The increasing of initial dye concentration leads to a decreasing conversion of dye while the ozonation rate increases. The formation of intermediates and the variation of pH, TOC, and nitrate ion during ozonation were investigated by the use of some analytical instruments such as GC/MS, GC, and IC. The intermediates of weak organic acids lower the pH value of the solution. The probable degradation mechanism of the Cationic Red X-GRL in aqueous solution was deliberated with the aid of Molecular Orbital calculations. The N(12)-C(13) site in Cationic Red X-GRL, instead of the N(6)-N(7) site, is found to be the principal site for ozone cycloaddition in the degradation processes. During the degradation process, among the six nitrogen atoms of Cationic Red X-GRL, one is transferred into a nitrate ion, one is converted into an amine compound, and the remaining four are transformed into two molecules of nitrogen.     

Decomposition pathways and reaction intermediate formation of the purified, hydrolyzed azo reactive dye C.I. Reactive Red 120 during ozonation

In this study, an aqueous solution of purified, hydrolyzed C.I. Reactive Red 120 (RR 120, Color Index), was selected as a model to investigate the degradation pathways and to obtain additional information on the reaction intermediate formation. The dye was purified to avoid the influence of the impurities on the ozonation process and on the formation of oxidation by-products. To simulate the dye-bath effluents from dyeing processes with azo reactive dyes, a hydrolyzed form of the dye was chosen as a representative compound. High performance liquid chromatography/mass spectrometry and its tandem mass spectrometry was chosen to identify the decomposition pathways and reaction intermediate formation during the ozonation process. In addition total organic carbon and high performance ion chromatography analysis were employed to obtain further information on the reaction processes during ozonation. Purified, hydrolyzed RR 120 was decomposed under the direct nucleophilic attack by ozone resulting in oxidation and cleavage of azo group and aromatic ring, while the triazine group still remained in the solution even after prolonged oxidation time (120 min) due to its high resistance to ozonation. Phenol, 1,2-dihydroxysulfobezene, 1-hydroxysulfonbezene were detected as the degradation intermediates, which were further oxidized by O(3) and *OH to other open-ring products and then eventually led to simple oxalic and formic acid identified by HPIC.     

Degradation of diuron in aqueous solution by ozonation

Degradation of diuron [3-(3,4-dichlorophenyl)-1,1-dimethylurea] in aqueous solution and the proposed degradation mechanism of diuron by ozonation were investigated. The factors that affect the degradation efficiency of diuron were examined. The generated inorganic ions and organic acids during the ozonation process were detected. Total organic carbon removal rate and the amount of the released Cl(-) increased with increasing ozonation time, but only 80.0% of the maximum theoretical concentration of Cl(-) at total mineralization was detected when initial diuron concentration was 13.8 mg L(-1). For N species, the final concentrations of NO3(-) and NH4+ after 60 min of reaction time were 0.28 and 0.19 mg L(-1), respectively. The generated acetic acid, formic acid and oxalic acid were detected during the reaction process. The main degradation pathway of diuron by ozonation involved a series of dechlorination-hydroxylation, dealkylation and oxidative opening of the aromatic ring processes, leading to small organic species and inorganic species. The degradation efficiency of diuron increased with decreasing initial diuron concentration. Higher pH value, more ozone dosage, additive Na2CO3, additive NaHCO3 and additive H2O2 were all advantageous to improve the degradation efficiency of diuron.     

铁及铁铜氧化物对臭氧氧化酸性红B的催化效能

采用自蔓延溶胶凝胶法分别制备了铁氧化物和铁铜复合氧化物催化剂,以酸性红B为降解对象,对比了单独臭氧氧化、铁氧化物和铁铜复合氧化物催化臭氧氧化对酸性红B的降解效果,考察了磁力搅拌速度(500～1 640 r/min)、溶液pH(3～11)、臭氧投加速率(3.55～28.4 mg/min)对铁铜复合氧化物催化性能的影响。结果表明,与单独臭氧氧化比较,铁氧化物和铁铜复合氧化物均能加速酸性红B的降解,促进色度和COD的去除,结合催化剂的表征结果,推断催化剂表面羟基促进臭氧分解产生.OH是其氧化性能较好的主要原因,另外,催化剂的吸附能力对催化性能也有一定影响。随着磁力搅拌速度、溶液pH、臭氧投加速率的增大,铁铜复合氧化物催化臭氧氧化酸性红B的效果越好。     

Oxidation of diethylene glycol with ozone and modified Fenton processes

This paper describes a study of oxidation of diethylene glycol (DEG) by ozone and modified Fenton process (hydrogen peroxide and ferric salt mixture) in aqueous solution. Both oxidation processes were able to oxidize relatively high concentrations of DEG effectively. DEG reacted primarily through hydroxyl radical produced by decomposition of ozone, and about 3 mol of ozone were consumed per mole of DEG removed during the process. For modified Fenton oxidation, stepwise addition of hydrogen peroxide (H2O2) and ferric salt (Fe(III)) resulted in much higher removal of DEG than one-time pulse addition of the chemicals. The extent of DEG removal increased with increasing concentrations of both H2O2 and Fe(III). Oxidant consumption per mole of DEG oxidized was one order of magnitude higher for hydrogen peroxide than those observed for ozone. Overall, ozonation produced higher concentrations of aldehydes, and modified Fenton treatment produced higher concentrations of carboxylic acids for the same levels of DEG oxidation. The major products of ozonation were glycolaldehyde, glyoxal, formaldehyde, acetaldehyde, and acetic, formic, pyruvic, oxalic and glyoxalic acids. The major products of modified Fenton oxidation were formaldehyde, and formic and acetic acids.     

NaNO(2)/FeCl(3) catalyzed wet oxidation of the azo dye Acid Orange 7

A combination of ferric chloride and sodium nitrite significantly improved the wet oxidation of the azo dye Acid Orange 7 (AO7) in acid aqueous media (pH 2.6) under moderate conditions (T=150 degrees C; oxygen pressure=0.5 MPa). To evaluate the catalytic system, wet oxidation of AO7 was carried out at temperatures between 90 and 150 degrees C and oxygen pressures ranging from 0.1 to 0.5 MPa. The effect of initial solution pH from 2.6 to 11.4 and the amount of catalyst on the degradation of AO7 were also investigated. AO7 initial concentration was kept 200 mg L(-1). The degradation process was monitored by UV-visible spectroscopy, HPLC, IC (ion chromatography), GC-MS and TOC analysis. At 150 degrees C and 0.5 MPa oxygen pressure, 56% TOC was removed after 4h of treatment, while no obvious TOC removal were achieved without catalyst at the same experimental condition. The main degradation products were some small organic acids: formic acid, acetic acid, pyruvic acid, oxalic acid, succinic acid (identified and quantified by IC) and phthalic acid (identified by GC-MS).     

Degradation of diuron in aqueous solution by ozonation

Degradation of diuron [3-(3,4-dichlorophenyl)-1,1-dimethylurea] in aqueous solution and the proposed degradation mechanism of diuron by ozonation were investigated. The factors that affect the degradation efficiency of diuron were examined. The generated inorganic ions and organic acids during the ozonation process were detected. Total organic carbon removal rate and the amount of the released Cl^? increased with increasing ozonation time, but only 80.0% of the maximum theoretical concentration of Cl^? at total mineralization was detected when initial diuron concentration was 13.8 mg L^?1. For N species, the final concentrations of NO₃ ^? and NH₄ ⁺ after 60 min of reaction time were 0.28 and 0.19 mg L^?1, respectively. The generated acetic acid, formic acid and oxalic acid were detected during the reaction process. The main degradation pathway of diuron by ozonation involved a series of dechlorination-hydroxylation, dealkylation and oxidative opening of the aromatic ring processes, leading to small organic species and inorganic species. The degradation efficiency of diuron increased with decreasing initial diuron concentration. Higher pH value, more ozone dosage, additive Na₂CO₃, additive NaHCO₃ and additive H₂O₂ were all advantageous to improve the degradation efficiency of diuron.     

Ozonation of hydrolyzed azo dye reactive yellow 84 (CI).

The combination of chemical and biological water treatment processes is a promising technique to reduce recalcitrant wastewater loads. The key to the efficiency of such a system is a better understanding of the mechanisms involved during the degradation processes. Ozonation has been applied to many fields in water and wastewater treatment. Especially for textile mill effluents ozonation can achieve high color removal, enhance biodegradability, destroy phenols and reduce the chemical oxygen demand (COD). However, little is known about the reaction intermediates and products formed during ozonation. This work deals with the degradation of hydrolyzed Reactive Yellow 84 (Color Index), a widely used azo dye in textile finishing processes with two monochlorotriazine anchor groups. Ozonation of the hydrolyzed dye in ultra pure water was performed in a laboratory scale cylindric batch reactor. Decolorization, determined by measuring the light absorbance at the maximum wavelength in the visible range (400 nm), was almost complete after 60 and 90 min with an ozone concentration of 18.5 and 9.1 mg/l, respectively. The TOC/TOC0 ratio after ozonation was about 30%, the COD was diminished to 50% of the initial value. The BOD5/COD ratio increased from 0.01 to about 0.8. Oxidation and cleavage of the azo group yield nitrate. Cleavage of the sulfonic acid groups of aromatic rings caused increases in the amount of sulfate. Formic acid and oxalic acid were identified as main oxidation products by high performance ion chromatography (HPIC). The concentrations of these major products were monitored at defined time intervals during ozonation.     

水体中酮硝基麝香的臭氧氧化降解研究

采用臭氧氧化水体中的酮硝基麝香,考察pH、H2O2等因素对降解程度的影响,结果表明提高初始pH能加快酮硝基麝香的氧化降解,当pH为12时,反应时间1 h,酮硝基麝香几乎完全去除,浓度为2 mol/L和5 mol/L的H2O2存在有利于O3分解生成·OH自由基,使得酮硝基麝香的氧化降解速率加快,当H2O2浓度超过5 mol/L,H2O2会成为·OH的清除剂,降低·OH利用率;无论O3单独作用和O3/H2O2协同作用,酮硝基麝香降解符合准一级动力学规律;酮硝基麝香氧化降解产物包括甲酸、二乙酸和硝酸根等,其中硝基从苯环上脱落降低了硝基麝香对环境的风险.     

Kinetics and mechanism for omethoate degradation by catalytic ozonation with Fe(III)-loaded activated carbon in water

The kinetics and mechanism for degradation of omethoate (OMT) by catalytic ozonation with Fe(III)-loaded activated carbon (Fe@AC) were investigated in this study with focus on identification of degradation byproducts. The rate constants of OMT reacting with ozone and hydroxyl radical (OH) were determined to be 0.04 and 5.3 × 10⁸ M^?1 s^?1 at pH 7.5 and 20 °C, respectively. OMT was predominantly degraded by OH in the catalytic ozonation with Fe@AC. The high-molecular-weight degradation byproducts identified were O,O,O-trimethyl phosphoric ester (TMP), pyrrolidin-2-one, N-methyl-2-sulfanylacetamide, 2-(methylthio)acetamide, O,O,S-trimethylthiophosphate (STMP), and N-methyl-2-(methylthio)acetamide. Besides, low-molecular-weight organic acids and inorganic anions were also detected and quantified, including formic, acetic and oxalic acids as well as nitrate, sulfate and phosphate ions. In the catalytic ozonation, TMP and phosphate were two major P-containing byproducts resulting from OMT degradation. The toxicity of OMT solution gradually decreased during the catalytic ozonation, indicating that Fe@AC is a safe catalyst for OMT removal by ozone in water.     

Comparison of photocatalytic degradation of dyes in relation to their structure

The photocatalytic degradation of a series of six acid dyes (Direct Red 80, Direct Red 81, Direct Red 23, Direct Violet 51, Direct Yellow 27, and Direct Yellow 50) has been tested compared in terms of color removal, mineralization, and toxicity (Lactuca sativa L. test) after photocatalysis on immobilized titanium dioxide. The dyes were examined at their natural pH and after hydrolysis at pH 12. Results show that hydrolysis decreases strongly the efficiency of color removal, that full mineralization takes much longer reaction time than color removal, and that toxicity is only very partially reduced. Some structural parameters, related to the structure and the topology of the dye molecules, could be correlated with the apparent color removal rates at natural pH.     

Mineralization of C.I. Reactive Yellow 84 in aqueous solution by sonolytic ozonation

The operational parameters and mechanism of mineralization of C.I. Reactive Yellow 84 (RY84), one of the azo dyes, in aqueous solution were investigated using sonolytic ozonation (US/O(3) oxidation). Of the pseudo-first-order degradation rate constants of TOC reduction, 9.0 x 10(-4), 7.3 x 10(-3) and 1.8 x 10(-2)min(-1) were observed with US, O3, and a combination of US and O3, respectively. These results illustrate that ozonation combined with sonolysis for removal of TOC is more efficient than ozonation alone or ultrasonic irradiation alone without considering the operating costs. With the initial pH value at 10.0, the ozone dose at 4.5 g h(-1), the energy density of ultrasound at 176 W l(-1), and the initial concentration of RY84 at 100 mg l(-1), the extent of mineralization measured as TOC loss was maximized. The variation of the concentrations of related ions (oxalate, formate, acetate, NO3(-), NO2(-), NH4(+), Cl(-), and SO4(2-)) during the reaction process was monitored. Other organic intermediates detected by GC/MS were N-methyleneaniline, phthalic acid, 4-hydroxyphthalic acid, isocyanatobenzene, aniline, 4-iminocyclohexa-2,5-dien-1-one, butene diacid and urea. Based on these findings, a tentative degradation pathway was proposed.     

Ozonation of an azo dye C.I. Remazol Black 5 and toxicological assessment of its oxidation products

The effect of ozonation (20.5 mgl(-1)) on the degradation processes of an azo dye, Remazol Black 5 (RB5; CI) was studied. Conventional parameters such as chemical oxygen demand (COD), total organic carbon (TOC), pH, conductivity, colour removal, biodegradability (BOD(5/28)), and toxic potential of the dye and its degradation products were monitored during the process. The results obtained indicated that ozonation is a highly effective way to remove the colour of a corresponding dye solution. However, a considerable organic load still remained as indicated by high COD and TOC residues. The COD, TOC reductions were about 40% and 25% for 6 h ozonation of 2 gl(-1) RB5 aqueous solution. During the ozonation process the rapid decrease of pH and the sharp increase of conductivity indicated the formation of acidic by-products and small fragments and ions which were identified by high performance ion chromatography. The BOD28 data revealed that first by-products after partial ozonation (10-150 min) of RB5 were more biodegradable than the parent compound and ozonation can enhance the biodegradability of azo dyes. During the first 150 min of total 360 min of oxidation, the formation of first by-products with high toxic potential took place as it could be confirmed by two acute toxicity-screening tests, the bioluminescence test (Vibrio fischerii) and the neutral red cytotoxicity assay (rat hepatoma cells). The significant enhancement of microbial biodegradability after long-term ozonation could also be seen as a decrease of toxic intermediates in correlation with the ozonation time as indicated in BOD28 biological degradation test results.     

Degradation of reactive dyes I. A comparative study of ozonation, enzymatic and photochemical processes

The environmental problems associated with textile activities are represented mainly by the extensive use of organic dyes. A great number of these compounds are recalcitrant and shown carcinogenic or mutagenic character. In this work three processes were studied for degradation of an anthraquinone dye (C.I. reactive blue-19). The ozonation process leads to complete decolorization with a very short reaction time; however, effective mineralization of the dye was not observed. The enzymatic process promotes quick decolorization of the dye; nevertheless, maximum decolorization degrees of about 30% are insignificant in relation to the decolorization degree achieved by the other processes. The best results were found for the photocatalytical process. The use of ZnO or TiO2 as photocatalysts, permits total decolorization and mineralization of the dye with reaction times of about 60 min.     

Decolorization and degradation of H-acid and other dyes using ferrous-hydrogen peroxide system

In this study, advanced oxidation process utilizing Fenton's reaction was investigated for the decolorization and degradation of two commercial dyes viz., Red M5B, Blue MR and H-acid, a dye intermediate used in chemical industries for the synthesis of direct, reactive and azo dyes. Effect of Fe2 +, H2O2, pH, and contact time on the degradation of the dyes was studied. Maximum color and COD removal was obtained for Red MSB, H-acid and Blue MR at 10-25 mg/l of Fe2+ dose and 400-500 mg/l of H2O2 dose at pH 3.0. The initial oxidation reaction was found to fit into first order rate kinetics and the rate of oxidation of H-acid was higher than the other dyes. Release of chloride and sulfate from the Fenton's treated Red M5B dye and sulfate from H-acid and Blue MR indicates that the dye degradation proceeds through cleavage of the substituent group.     

Ozonation of azo dye in a semi-batch reactor: a determination of the molecular and radical contributions

Azo dye ozonation was carried in a semi-batch reactor to evaluate both the molecular and radical contributions of ozone on the dye decay. From two mass balance equations, the simultaneous determination of mass transfer, self-decomposition and solubility parameters of ozone were determinated; thus establishing the steady state conditions in the experimental system. The results of kinetic studies showed that the decay of azo dye was a pseudo-first-order reaction with respect to dye concentration and the overall rate constant increased with an increase in the pH, however declined with an increase in the dye concentration. Furthermore, from the overall rate constants obtained at various pH values a mathematical analysis of dye decay was performed, which provides a practical new method to quantify the radical and molecular contributions in the ozonation of azo dyes.     

Degradation of azo dyes using low iron concentration of Fenton and Fenton-like system

This study investigated Fenton and Fenton-like reactions at low iron concentration (相似文献   

Photochemical oxidant pollution and vegetation: effects of mixtures of gases, fog and particles

Photochemical 'smog' contains mixtures of gases (e.g. ozone, nitrogen dioxide), and dry particles (e.g. nitrates). Intermittent fog in the same geographical area can be acidic with high concentrations of nitric acid. Results from recent field studies in the Los Angeles Basin have emphasized the relative toxicity of these components of photochemical air pollution. Studies have focused on gaseous+fog or gaseous+dry particulate effects on conifers, gaseous+fog effects on crops, and the effects of trace pollutants produced during generation of ozone on crops. Data from these studies indicate that direct alterations in growth and physiological responses were observed only with gaseous pollutants (primarily ozone), or repeated applications of highly acidic fogs (pH < 2.7). Direct particle dry deposition effects are unclear. Few interactions have been found between gaseous pollutants and acidic fog. Charcoal-filtered open-top chambers are highly effective in removing pollutants in the following order: fog (100%) > peroxyacetyl nitrate > ozone > nitrogen dioxide > sulfur dioxide > nitrate ion > ammonium ion > sulfate ion. However, nitric oxide concentrations are higher in charcoal-filtered chambers than in ambient air. The studies point out the importance of considering other components of photochemical pollution in addition to ozone, especially when investigating subtle, long-term effects on vegetation.     

Degradation of anthraquinone dye C.I. Reactive Blue 19 in aqueous solution by ozonation

This study investigated the degradation of anthraquinone reactive dye C.I. Reactive Blue 19 (RB-19) with initial concentration of 100 mg L⁻¹ in aqueous solution by ozone oxidation. The results of UV/VIS and FTIR spectra showed that the anthraquinone structures, nitrogen linkages and amino groups of RB-19 were destroyed under direct ozone reaction. The identification by LC–MS and GC–MS analyses indicated that some organic acids (e.g., phthalic acids) and 1,3-indanone could be the primary degradation products, respectively. The Microtox toxicity of the ozonated RB-19 solution initially increased but subsequently decreased when ozonation time increased. This detoxification accompanied biodegradability enhancement revealed by BOD/COD ratio increasing from 0.15 to 0.33 after 10 min of ozonation.