阳离子淀粉-丙烯酰胺接枝共聚物絮凝剂的制备及其絮凝性能

研究了阳离子淀粉与丙烯酰胺接枝共聚反应制备阳离子型絮凝剂的工艺,并用硅藻土悬浊液及实际水样对产物的絮凝性能进行了考察。其最佳合成条件：阳离子淀粉与丙烯酰胺的质量比为1：4,引发剂加入量为丙烯酰胺质量的0．1％,反应温度50℃,反应时间3h。絮凝效果实验中,接枝共聚物絮凝剂的最佳加入量为4mg／L。与阳离子淀粉和阳离子聚丙烯酰胺絮凝剂相比,接枝共聚物絮凝剂对渭河水及造纸网下白水的絮凝效果更好。     

微波辐射下改性壳聚糖的制备及其絮凝性能

采用微波辐射法合成了壳聚糖-丙烯酰胺接枝共聚物。通过傅立叶变换红外光谱(FTIR)谱图对比分析表明,丙烯酰胺成功地接枝到壳聚糖上,发生了接枝共聚反应;产物的热重-差热(TG-DSC)谱图表明,壳聚糖-丙烯酰胺接枝共聚物的热稳定性比壳聚糖差。壳聚糖-丙烯酰胺接枝共聚物作为絮凝剂处理高岭土悬浊液的最佳条件为:絮凝剂加入量4.0 mg/L,沉降时间20 min,溶液pH 7。处理印染废水时,与壳聚糖相比,壳聚糖-丙烯酰胺接枝共聚物加入量较少而COD去除效果较好。在废水pH为7、絮凝剂加入量为100 mg/L、沉降时间为20 min的条件下,壳聚糖-丙烯酰胺接枝共聚物对废水COD去除率达41.55%。     

疏水改性阳离子聚丙烯酰胺絮凝剂的制备及其絮凝性能

通过水溶液共聚合法,以丙烯酰胺(AM)、丙烯酰氧乙基三甲基氯化铵(DAC)和2-乙烯基吡啶(2-VP)为共聚单体合成了疏水改性阳离子聚丙烯酰胺P(AM-DAC-2VP),并用红外光谱仪和核磁共振光谱仪对其结构进行了表征。实验结果表明:当w(2-VP)为1.0%、w(DAC)为30%、活性污泥pH为5、P(AM-DAC-2VP)加入量为25mg/L时,P(AM-DAC-2VP)对本实验的活性污泥絮凝能力最强,上清液透光率为92.1%;P(AM-DAC-2VP)比同条件下制备的阳离子聚丙烯酰胺P(AM-DAC)具有更好的絮凝效果。     

两性聚丙烯酰胺的制备及其絮凝性能

开发了一种对非离子聚丙烯酰胺进行改性制备两性聚丙烯酰胺(APAM)絮凝剂的新方法。以硅藻土悬浮液为絮凝对象,考察了改性反应中影响APAM絮凝效果的因素。结果表明,采用无水乙酸与三甲胺、环氧氯丙烷合成季胺盐型阳离子剂的方法优于采用盐酸的方法;在10mL质量分数为10%、相对分子质量为3×106的非离子型聚丙烯酰胺水溶液中加入8mL浓度为2.6mol/L的阳离子剂,同时控制V(NaOH)∶V(NaClO)为0.44,改性得到的APAM絮凝性能最佳,在pH3～9的较宽范围内对硅藻土悬浮液有较好的絮凝效果。在pH为3、APAM加入量为1.8mg/L时,硅藻土悬浮液的絮凝率可达100%。     

丙烯酰胺接枝木薯淀粉的合成及橡胶废水的絮凝处理

以丙烯酰胺为单体,过硫酸铵为引发剂,十二烷基磺酸钠为乳化剂,采用乳液聚合法合成丙烯酰胺接枝木薯淀粉(接枝淀粉)。实验结果表明:当m(淀粉)∶m(单体)为1.0∶1.5、合成温度为60℃、引发剂加入量(质量分数)为2.4%时,单体转化率、接枝率和接枝效率分别为74.7%,69.8%,74.9%;当接枝淀粉的加入量为0.35g/L时,絮凝处理后橡胶废水的吸光度由0.164降为0.073,脱色率为55.5%。     

壳聚糖-丙烯酰胺-丙烯酸三元接枝共聚物去除废水中铜离子研究

研究pH值、温度、反应物比率对生成三元接枝共聚物的影响,三元接枝共聚物接枝率与接枝效率的计算,以及三元接枝共聚物对铜离子的吸附效果.实验与计算结果表明：生成三元接枝共聚物的最佳反应条件为引发剂（NH4）2S2O8用量6 mmol/L,反应温度50℃,壳聚糖（CTS）：丙烯酰胺（AM）：丙烯酸（AA）=1∶2.7∶0.3,pH值=7,反应时间5h;在相同条件下,三元接枝共聚物对铜离子去除效果比壳聚糖有了明显的改善,对铜离子去除率最高达到90.06％,比壳聚糖对铜离子的去除率高49.72％.     

P(AM-DMDAAC-VAM)共聚物的合成及其絮凝性能

以丙烯酰胺(AM)、二甲基二烯丙基氯化铵(DMDAAC)、乙酸乙烯酯(VAM)为单体,采用水溶液自由基胶束共聚合法合成了疏水缔合阳离子型共聚物P(AM-DMDAAC-VAM),并对其进行了红外光谱和核磁共振氢谱表征。实验结果表明:在P(AM-DMDAAC-VAM)加入量为14 mg/L、絮凝温度为30~60℃、硅藻土悬浊液pH为8~11时,P(AM-DMDAAC-VAM)对硅藻土悬浊液的絮凝效果最好,上清液透光率高达97.5%。     

壳聚糖三元接枝共聚物的合成及其阻垢性能

以壳聚糖(CTS)、衣康酸(IA)和马来酸酐(MA)为原料,以醋酸为溶剂、(NH_4)_2S_2O_8为引发剂,合成了CTS-IA-MA三元接枝共聚物。聚合反应的最佳条件为:反应温度90℃,n(CTS):n(IA):n(MA)=1:1.5:1.0,引发剂质量分数0.35%,反应时间5 h。通过傅立叶变换红外光谱(FTIR)表征,所得产物为CTS-IA-MA接枝共聚物。三元接枝共聚物质量浓度为50 mg/L、水样pH为中性或弱酸性时三元接枝共聚物对CaCO_3的阻垢效果较好。     

壳聚糖-丙烯酰胺-二甲基二烯丙基氯化铵三元接枝共聚物的合成及应用

在N2保护下,以硝硬驱铈铵为引发剂,将壳聚糖（CTS）、丙烯酰胺（AM）及二甲基二烯丙基氯化铵（DMDAAC）接枝共聚得到CTS-AM-DMDAAC三元接枝共聚物,考察了反应条件对接枝共聚反应的影响。实验结果表明,在反应温度50℃、反应时间5-6h,m（CTS）：m（AM）：m（DMAAAC）=1：6：0.67、c（Ce^4＋）=0.8mmol/L的最佳反应条件下,接枝共聚反应的接枝率和接枝效率分别为64%和10.5%。用傅里叶变换红外光谱仪对CTS-AM-DMDAAC进行了表征。絮凝实验结果表明：CTS-AM-DMDAAC对高岭土水样具有较强的絮凝能力,可在很宽的pH范围内使用。用CTS-AM-DMDAAC处理COD为165.5mg/L的啤酒生产废水,COD去除率达90.1%.     

复合絮凝剂PSAM在电厂冲灰水处理中的应用研究

以水玻璃、聚合氯化铝(PAC)、非离子型聚丙烯酰胺(N-PAM)为原料,制备了复合型无机高分子絮凝剂PSAM,初步验证了其对电厂冲灰废水的絮凝净化效果,考察了投药量、铝与硅摩尔比、水样pH等因素对絮凝效果的影响,并与聚硅酸铝(PACS)及传统使用的PAC进行了比较.结果表明,PSAM稳定性良好、有较宽的pH适用范围,絮体颗粒粗大、密实,沉降速度快, 余浊低,优于所对比药剂.     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6～9,COD 302mg／L,BOD5 108mg／L,SS30mg／L,色度36倍,水质达到GB8978--1996（污水综合排放标准》三级标准。     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Does Soil Acidification Affect Spruce Needle Chemical Composition and Tree Growth?

In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.     

Solubility and Potential Mobility of Heavy Metals in Two Contaminated Urban Soils from Stockholm,Sweden

The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.     

High Immobilization of NH4+ in Danish Heath Soil Related to Succession,Soil and Nutrients: Implications for Critical Loads of N

During recent decades heathlands havechanged into grasslands in regions with high atmosphericnitrogen deposition. In regions with intermediatedeposition level (e.g., Denmark) changes have been lesspronounced which may be due to delay or decrease inresponse of the ecosystem. The mor layer (O horizon) mayplay an important role for this delay due to high sinkstrength for N. In this study, the capacity for netNH₄ ⁺ immobilization and mineralization wasstudied during short- and long-term incubations (2–36 days)of mor samples from Danish dry inland heaths. High short-term capacity for net NH₄ ⁺ immobilization wasfound to be a general characteristic of Danish heath morlayers both under heather (Calluna vulgaris) andcrowberry (Empetrum nigrum ssp nigrum), the latterdominating late stages in heathland succession. The netNH₄ ⁺ immobilization was higher under youngcompared to old or dead vegetation, and higher on lessnutrient poor soils than on extremely nutrient poor soils.The addition of N, P and C stimulated CO₂ productionand net NH₄ ⁺ immobilization, but not net Nmineralization. The immobilization of ¹⁵NH₄ ⁺caused release of dissolved organic N, increased N anddecreased C/N ratio in the microbial biomass, and indicatedgrowth of microorganisms with other metabolic abilitiesthan the indigenous population. No evidence was obtained ofstabilization of immobilized ¹⁵NH₄ ⁺ intosoil organic matter during the experiment. On background ofthe results and current knowledge it was concluded that therecognition of the high capacity for net NH₄ ⁺immobilization in mor layers does not allow for a raiseof critical loads for N for northern dry inland heaths.     

Biodegradation of Injection Molded Starch-Poly (3-hydroxybutyrate-co-3-hydroxyvalerate) Blends in a Natural Compost Environment

Injection molded specimens were prepared by blending poly (hydroxybutyrate-co-valerate) (PHBV) with cornstarch. Blended formulations incorporated 30% or 50% starch in the presence or absence of poly-(ethylene oxide) (PEO), which enhances the adherence of starch granules to PHBV. These formulations were evaluated for their biodegradability in natural compost by measuring changes in physical and chemical properties over a period of 125 days. The degradation of plastic material, as evidenced by weight loss and deterioration in tensile properties, correlated with the amount of starch present in the blends (neat PHBV < 30% starch < 50% starch). Incorporation of PEO into starch-PHBV blends had little or no effect on the rate of weight loss. Starch in blends degraded faster than PHBV and it accelerated PHBV degradation. Also, PHBV did not retard starch degradation. After 125 days of exposure to compost, neat PHBV lost 7% of its weight (0.056% weight loss/day), while the PHBV component of a 50% starch blend lost 41% of its weight (0.328% weight loss/day). PHB and PHV moieties within the copolymer degraded at similar rates, regardless of the presence of starch, as determined by ¹H-NMR spectroscopy. GPC analyses revealed that, while the number average molecular weight (Mn) of PHBV in all exposed samples decreased, there was no significant difference in this decrease between neat PHBV as opposed to PHBV blended with starch. SEM showed homogeneously distributed starch granules embedded in a PHBV matrix, typical of a filler material. Starch granules were rapidly depleted during exposure to compost, increasing the surface area of the PHBV matrix.