高锰酸钾——硫酸——过硫酸钾消化冷原子荧光法测定总悬浮颗粒物中…

测定环境大气悬浮颗粒物中痕量汞，用４种消化液进行对比实验，其中高锰酸钾－硫硫－过硫酸钾混合液消化效果较好，用冷原子荧光测定操作简便，检测下限为０．０５μｇ／Ｌ，重复测定９个实际样品，相对标准偏差为１１．６％，变异系数为１０．４％，添加汞标准回收率为１０２％。     

高锰酸钾─硫酸─过硫酸钾消化冷原子荧光法测定总悬浮颗粒物中痕量汞

测定环境大气悬浮颗粒物中痕量汞，用４种消化液进行对比实验，其中高锰酸钾─硫酸─过硫酸钾混合液消化效果较好，用冷原子荧光测定操作简便，检测下限为０．０５μｇ／Ｌ，重复测定９个实际样品，相对标准偏差为１１．６％，变异系数为１０．４％，添加汞标准回收率为１０２％。     

气相色谱法测定苯系物标准样品

提出了以二硫化碳为稀释剂，用氯苯作内标物，采用程序升温，调节载气流量，在一根色谱柱上使苯系物标准样品中的7个组分得到完全分离。对苯系物标准样品进行多次测定，各组分的测定结果均在标准样品的保证值范围内，相关标准差小于3％，方法的准确度和精密度均较好。     

红外分光光度法测定处理后油气田含油污泥中石油类方法适用性研究

为研究红外分光光度法测定处理后油气田含油污泥中石油类的适用性，选取6家实验室分别对空白模拟样品和4个浓度的实际样品进行测定。结果表明，该方法的检出限为0.02 mg/g;实验室内及实验室间的相对标准偏差分别为0.9%～9.4%、2.5%～8.3%;加标回收率83.0%～110%。该方法具有检出限低、精密度和准确度较高的特点，为处理后油气田含油污泥中石油类的检测提供参考方法。     

氢化物发生—石墨炉原子吸收光谱法测定大气样品中微量砷

本文用浸渍聚乙烯氧化吡啶试剂的滤纸采集样品,经混合酸湿法消解,在5％盐酸介质中加入硼氢化钠溶液作为还原剂,使砷生成砷化氢,由氩气直接载入原子吸收光谱仪的石墨炉进行测定。以此方法测定了8种大气样品和煤飞灰标样(82201),结果表明最低检出限为0.005μg(砷)/ml,相对标准偏差1.21～5.79％,回收率85.1～92.4％。用浓度为10％的聚乙烯氧化吡啶溶液浸渍滤纸,采集样品时大气中蒸气和气溶胶态的砷化物采集效率可达97％以上     

离子色谱法测定污泥与餐厨垃圾联合厌氧发酵液中有机酸

采用离子色谱法同时测定污泥与餐厨垃圾联合厌氧发酵液中乳酸、乙酸、丙酸、正丁酸、异丁酸、正戊酸、异戊酸等7种有机酸,通过试验优化洗脱程序,使得7种有机酸在2．00mg／L～60．0mg／L范围内线性良好。试验表明,方法检出限为0．250mg／L～0．580mg／L,标准样品的加标回收率为93．O％～108％,8次测定结果的RSD为3．7％一7．1％,实际样品测定的加标回收率为90．6％～109％。     

毛细管气相色谱法同时测定水中的7种挥发性卤代烃

用毛细管气相色谱法同时测定饮用水中7种挥发性卤代烃的研究．实验表明，该方法前处理简单，测定方便，具有较好的灵敏度、准确度和精密度，结果令人满意．样品的加标回收率在90％～110％，相对标准偏差小于5％．     

高灵敏雾化-火焰原子吸收光谱法测定烟尘中低含量铅

将高灵敏雾化技术用于火焰原子吸收光谱法，并测定了烟尘样品中的低含量铅，取得较满意的结果。当采样300L、样品溶液为25mL时，铅的检测限可达0.0012mg/m^3，方法标准曲线线性范围为0mg/L-1.0mg/L，相对标准差小于4.5％，加标回收率在87％-97％之间，并具有简便快速等特点。     

空气颗粒物中铅、镉超声浸取-原子吸收测定方法研究

用超声波震荡方法对大气滤膜样品进行前处理,提取待测元素。研究了浸取液种类、酸度、浸取时间和干扰因素等,确定了颗粒物样品溶液制备的最佳条件,与流动注射在线富集——原子吸收技术结合,建立了大气颗粒物样品测定Pb、Cd方法。结果表明,方法快速、准确,标准样品测定回收率在97％以上,6次测定方目对标准偏差小于2.6％。     

助催化无汞盐快速测定水中化学需氧量

在ψ（Ｈ２ＳＯ４）＝５６％硫酸介质，重铬酸钾的氧化体系中，以钼权铵，硫酸铝钾为助催化剂，可减少量化剂硫酸银的用量，消解１５ｍｉｎ即可测定水中化学需氧量，用硝酸银溶液代替硫酸汞去除水氯离子，避免了汞盐的污染，工业废水回收率在９７％～１０１％之间，有较好的准确度。     

江苏省典型污水处理厂脱水污泥热值及其影响因素分析

以江苏省20家典型污水处理厂脱水污泥为对象,通过采样监测分析,探讨了目标污水处理厂脱水污泥干基热值特征,并采用偏相关、脱水污泥工业及元素分析等,研究影响污水处理厂污泥热值的因素。结果表明:江苏省脱水污泥的热值范围为5 328~15 069 kJ/kg,均值为9 883 kJ/kg,低于中国大中型城市平均水平,苏南地区脱水污泥热值显著高于苏中地区和苏北地区;偏相关分析结果显示,2011年絮凝剂种类与脱水污泥热值显著相关,2021年显著性因素为污水类型,混入工业废水和采用有机高分子絮凝剂均会对脱水污泥热值产生显著的正向影响;工业分析和元素分析结果显示,混入工业废水和采用有机高分子絮凝剂均会提高脱水污泥中有机物、挥发分及固定碳含量,与其对脱水污泥热值的影响规律一致;有机高分子絮凝剂的使用还更易使脱水污泥发生水解反应和脱碳酸反应。     

Repetitive extragenic palindromic PCR (REP-PCR) as a method used for bulking process detection in activated sludge

Bulking of activated sludge is a world-widely prevalent problem and can lead to loss of bio-oxidation, further deterioration of effluent quality, and even to a complete breakdown of the entire treatment process. Most common reasons of bulking are bacterial community changes, especially excessive growth of filamentous bacteria or excess of biopolymers on surface of non-filamentous microbes. Because of complex nature of the bulking phenomenon, the successful bulking control strategy finding is still a very important need awaiting new options and advices. The repetitive extragenic palindromic PCR (REP-PCR) fingerprinting method has been applied to distinguish bacterial community in non-bulking and bulking activated sludge. The characteristic REP-PCR fingerprinting patterns, using the Ward??s clustering method, have been analyzed to determine homology/similarity relation between particular non-bulking and bulking sludge sampling. The received clustering results were in high concordance with activated sludge typing done based on physicochemical sludge analysis. The choice and application of molecular typing method in sludge analysis will depend upon the needs, skill level, and resources of the laboratory. The proposed REP-PCR method and statistical analysis of fingerprinting patterns seems to be simple, rapid, and effective methods to show differences between population in non-bulking and bulking activated sludge. It is easy to implement, and it may be useful for routinely activated sludge monitoring as well as may be helpful in early detection of bulking process.     

Heavy metal concentration and speciation of seven representative municipal sludges from wastewater treatment plants in Northeast China

The analysis of heavy metals is very important for assessing the feasibility of the agricultural utilization for the municipal sludge. In this paper, a four-step sequential extraction method was applied to extract heavy metals (Cu, Zn, Mn, Cr, and Ni) in municipal sludges from seven individual wastewater treatment plants located in Jilin and Heilongjiang Province, China, for estimating the mobility and bioavailability of the metal ions in the agricultural application. The total concentrations of heavy metals and their chemical fractions after the sequential extraction were determined. Principal component analysis (PCA) was applied to analyze the relations of heavy metals fractions in the municipal sludges. Experimental results indicated that the total concentrations of Cu, Zn, Cr, and Ni in all sludge samples were below the threshold values set out by the Chinese legislation (GB18918-2002). Specially, Zn had a high bioavailability and mobility, Cu and Cr had potential bioavailability, while Mn mainly existed in the residual fraction of municipal sludge. On the other hand, Ni had different mobility in different municipal sludge. PCA results were confirmed by the environmental behavior of heavy metals.     

Identification of surfactant degradation products as toxic organic compounds present in sewage sludge

A cost-effective strategy combining chemical analysis and bioassays for the identification of polar toxic compounds in sewage sludge is reported. ToxAlert 100 bioluminescence inhibition assay was used in combination with chemical analysis involving extraction, clean-up, chromatographic separation and mass spectrometry detection. This methodology was applied to real samples of sludge from three wastewater treatment plants (WWTP) located in Catalonia (Spain) during a 3 month period. In the first step, sewage sludge was lyophilized, treated by sonication with a mixture of methanol and chloroform and finally cleaned up using a sequential solid phase extraction (SSPE) with an octadecylsilica cartridge (C18) in series with a polymeric Lichrolut EN cartridge (Lic EN). In the second step, the toxicity of each fraction of the sludge sample was investigated using the ToxAlert 100. The unequivocal identification and quantification of polar organic cytotoxic substances present in the fractionated extracts were determined by liquid chromatography-mass spectrometry (LC-MS). Major toxic compounds identified were: non-ionic polyethoxylated surfactants (nonylphenol polyethoxylates, alcohol polyethoxylates), their intermediates (polyethylene glycol polyethoxylated, nonylphenol carboxylates and polyethoxylated alcohol carboxylates), linear alkylbenzenesulfonates and heavy metals. The toxic response (in terms of bioluminescence inhibition using ToxAlert 100), defined by the 50% effective concentration (EC50), and the toxicity units (TU) for every standard non-ionic surfactant were calculated. The results provided the identification of polar cytotoxic compounds as well as the evaluation of their contribution to the total toxicity observed in sewage sludge.     

污水处理厂污水和污泥中PAHs的残留及风险研究进展

多环芳烃(PAHs)是一类极其复杂的有机污染物,衍生物种类较多,1976年美国环保局因其致癌、致畸、致突变将其中的16种列为优先控制污染物。城市污水处理厂作为一个地区污染物迁移和转化的重要媒介,在控制和截断PAHs进入天然水体的过程中扮演着重要的角色。因此,研究污水处理厂中PAHs的浓度水平对于了解和控制PAHs进入天然水体和通过污泥进入到土壤中进而通过食物链危害人类健康具有重要的意义。文章综述了污水处理厂污水和污泥中PAHs的前处理技术、分析方法、浓度水平、生态风险以及国内外污水处理厂污泥土地利用现状。     

印染废水处理污泥危险废物鉴别过程中有毒污染物的迁移转化及鉴别因子筛选

简述了印染废水处理污泥危险废物鉴别过程中有毒污染物的迁移转化及鉴别因子筛选。以采用活性染料的印染企业为例,从常用的原辅材料、使用的生产工艺、常用的废水处理工艺等几个方面来对印染废水处理污泥危险废物鉴别过程中有毒污染物的迁移及转化进行分析。提出危险废物鉴别工作任重而道远,危险废物鉴别的关键在于日常监管。     

微波消解-原子吸收/原子荧光光度法测定活性污泥中的Cd、Pb、Ni、Cu、 Zn、Cr、K、As、Hg

通过实验,建立了活性污泥中金属和重金属的测定方法。活性污泥样品经硝酸—氢氟酸或硝酸—高氯酸微波消解处理后,Pb、Ni、Cu、Zn、Cr、K选用火焰原子吸收分光光度法测定,Cd用石墨炉原子吸收分光光度法测定,As、Hg用原子荧光光度法测定。该方法操作简单,结果准确,重现性好。样品加标回收率为93%-108%,相对标准偏差〈5%。     

Farmers’ attitude toward treated sludge use in the villages of West Bank,Palestine

An application of treated sewage sludge on agricultural land has been widely accepted, as this method is simple and economical for disposal of wastewater residues. When applied properly on an agricultural land, sludge can replenish organic matter and nutrients in soil. Although sewage sludge has been used in agriculture in many parts of the world, its acceptability varies with different cultures and beliefs among farmers. Farmers’ concerns on sludge use are primarily due to its anthropogenic origin, pollutants that it carries, a general perception of sewage being dirty, and its offensive odor. This paper aims to investigate farmers’ perceptions on land application of treated sewage sludge on their farm. This study targeted two farming communities, namely, Anza and Beit Dajan villages, located in Jenin and Nablus districts in the West Bank, Palestine. In this study, a sample of 106 farmers were randomly selected and surveyed through a mixture of structured and open-ended questions. Results indicated that, overall, farmers have positive perceptions on land application of sludge. A majority of the farmers are in favor of the concept of sludge use when a planned wastewater treatment plant is constructed and it becomes operational. Results also indicate that a majority of the farmers are in favor of using sludge for fertilizing fruit trees, rather than growing vegetables and other plants in a greenhouse, and that many of them have knowledge of sludge properties and advantages and disadvantages of sludge use in agriculture. Despite the positive perceptions by the majority of farmers, a small fraction of the farmers are in disfavor of the use of sludge for the following reasons: psychological and social concerns, potential health risks, and their religious beliefs. Results further suggest that the land application of treated sewage sludge can be accepted by more farmers if the consumers are willing to buy agricultural products fertilized by sludge, sludge meets the public health requirements, and sludge is available at low costs. To improve farmers’ perceptions on the land application of sludge, several measures are recommended.     

COD adsorption capacity of the activated sludge — Its determination and application in the activated sludge process

Proper control of the activated sludge process is essential in ensuring production of good effluent. COD adsorption capacity (CAC) of the activated sludge could be used as a control parameter. CAC is determined by mixing the activated sludge with the settled sewage and measuring the instantaneous COD reduction per unit mass of activated sludge. CAC measures substrate removal by physical adsorption and reflects the quality of the activated sludge. CAC of a healthy activated sludge increases with the flow along the aeration units. CAC could be used for process decision on variation in air supply and feed pattern to the aeration units. In a modified process to cope with sludge bulking problem, CAC could be used to estimate the air supply to the aeration unit which is merely used for reaerating the returned sludge.