Quasi-dynamic leaching characteristics of polychlorinated dibenzo-p-dioxins and dibenzofurans from raw and solidified waste incineration residues

Quasi-dynamic leaching characteristics of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) from raw and solidified air pollution control (APC) residues were examined via a nine-time multiple leaching test. The effect of injected activated carbon in the APC residues on the PCDD/F leachability was also evaluated. When humic acid solution was used as a leachant, the leaching concentrations of PCDD/Fs fluctuated between the first and the fifth leaching, followed by a gradual increase and then suddenly reached maximum values at the leaching sequences around seventh and eighth. This significant enhancement in PCDD/F leachability was mainly due to an increase in the release of highly chlorinated PCDD/Fs. Leaching of PCDD/Fs with n-hexane was, in contrast, primarily caused by the partitioning of hydrophobic PCDD/Fs between the APC residue surface and the liquid phase of n-hexane. Consequently, the largest leaching concentrations for n-hexane tests achieved at the first leaching, followed by a decrease and reached plateaus. Solidification/stabilization (S/S) decreased the PCDD/F leachability up to the fifth leaching by the use of humic acid solution. However, S/S increased the PCDD/F leaching concentrations and rates with n-hexane. The activated carbon in APC residues significantly inhibited the release of PCDD/F with n-hexane. The inhibiting effect provided by activated carbon was, however, less significant by the use of humic acid solution.     

Effects of copper chloride on formation of polychlorinated dibenzo-p-dioxins in model waste incineration

Combustion experiments in a laboratory-scale fluidized-bed reactor were conducted to elucidate the effects of copper chloride as a catalyst on polychlorinated dibenzo-p-dioxins (PCDDs) formation in municipal waste incineration. We used model wastes with and without copper chloride (CuCl₂ · 2H₂O), both of which contained polyvinyl chloride as a chlorine source. Combustion temperature was set to 900 °C, and the amount of air supplied was twice the stoichiometric ratio. The experimental setup was carefully planned to suppress the influences of experimental conditions except the waste composition. Results of these experiments showed that copper chloride in the waste increased the amount of PCDDs formed and made the homologue profile to shift towards the highly chlorinated species. Copper chloride contributes to the PCDDs formation by promoting chlorination, whereby the reaction is important in that organic matter is chlorinated directly by copper compounds. Copper chloride did not exert a great influence on the isomer distribution patterns of PCDDs, while there appeared a significant difference in the case of PCDFs. This points out the difference of the major formation mechanisms between PCDDs and PCDFs. PCDDs are less formed by the catalytic reactions from carbon/polycyclic aromatic hydrocarbons than PCDFs in our experimental conditions.     

Correlation of polychlorinated naphthalenes with polychlorinated dibenzofurans formed from waste incineration

Isomer composition of polychlorinated naphthalenes (PCNs) was measured for municipal waste incinerator fly ash samples and for emission samples produced from soot and copper-deposit experiments conducted at the United States Environmental Protection Agency (US-EPA). Two types of PCN isomer patterns were identified. One pattern contained specific PCN isomers in which chlorine atoms are substituted as if the peri(alpha-) position were dechlorinated from the higher chlorinated PCNs one by one. In another pattern, the isomers had a tendency for the chlorine atoms to assume successive positions on the naphthalene ring, which may be caused by specifically oriented chlorination. Some of these isomers increased, together with several polychlorinated dibenzofuran (PCDF) and a few polychlorinated dibenzo-p-dioxin (PCDD) isomers. The ratios between some specific PCN, PCDF, and PCDD isomers measured for the fly ash samples agree with those obtained from the soot and copper-deposit experiments. The observations suggest that these isomers were formed possibly from de novo synthesis utilizing the carbon structure contained in soot under the catalytic effect of a copper compound. Typical isomers for PCNs and PCDFs produced from incineration emissions were identified.     

The size distribution of polychlorinated dibenzo-p-dioxins and dibenzofurans in the bottom ash of municipal solid waste incinerators

In this study, bottom ash was sampled from two Taiwanese municipal solid waste incinerators (MSWIs: A and B) and sieved to size classes of 4.75-9.5 mm, 2.36-4.75 mm, 1.0-2.36 mm, 0.6-1.0 mm, 0.3-0.6 mm, 0.21-0.3 mm, 0.125-0.21 mm, 0.075-0.125 mm and <0.074 mm. For both MSWIs, the major peak in the particle size distribution for the PCDD/F content was found in a particle size <0.21 mm, that is, 16.1 (A) and 4.37 pg I-TEQ/g (B). This is due to the fact that a smaller particle has higher specific surface area thus offering more adsorption sites. The mean cumulative fractions (F%) of PCDD/F I-TEQ in the bottom ash of MSWI A and B in the particle size range below 0.6, 2.36 and 4.75 mm, in sequence, are 40.4%, 77.2% and 95.6%, respectively. We suggest sieving the bottom ash before the subsequent reutilization at the suggested cut size of 0.6 mm. In the view of PCDD/Fs, bottom ash with a particle size larger than 0.6 mm, which is the more non-hazardous part, may be suitable for being the raw material of landfilling soil, road sub-base, and construction blocks. For the minus 0.6 mm fraction, vitrification with fly ash is one of the choices.     

Effects of injected activated carbon and solidification treatment on the leachability of polychlorinated dibenzo-p-dioxins and dibenzofurans from air pollution control residues of municipal waste incineration

To assess the effectiveness of the injected activated carbon, cement, and sulfur-containing chelating agent in controlling polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) release from the surface of air pollution control (APC) residues, this study examined the leachability of PCDD/Fs from APC residues generated by municipal solid waste incinerators. Results showed that PCDD/Fs were stably retained in the APC residues when the samples were leached with acetic acid solution. Highly chlorinated PCDD/F homologues (i.e., hepta- and octa-CDDs and CDFs) were relatively easy to leach. The leaching percentages of PCDD/Fs from raw APC residue samples containing activated carbon were smaller than those from samples without activated carbon, especially when n-hexane was used as the leachant. These results indicate that the flue gas injected activated carbon not only controls PCDD/F emissions, but also suppresses the leachability of PCDD/Fs from the APC residues. Solidification/stabilization (S/S) processes with 30wt% cement and 5wt% sulfur-containing agent can additionally decrease the leachability of PCDD/Fs with humic acid. Using n-hexane as the leachant, S/S processes increased the leachability of PCDD/Fs. Various low chlorinated PCDD/F congeners were moreover leached out of the APC residue samples, markedly increasing the leachate toxicity. The enhancement of leachability and toxicity owing to S/S processes may negatively impact the environment when APC residues are exposed to nonpolar organic solvents.     

Formation of polychlorinated dibenzo-p-dioxins/dibenzofurans from residual carbon on municipal solid waste incinerator fly ash using Na37Cl

Na37Cl was used to study the role of chlorine in the formation of polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF) from carbon. Adding Na37Cl to fly ash showed that this compound was a (relatively) poor chloride source; chlorine naturally present on the ash - which could include both chlorine in residual carbon and (metal) chlorides - was found to be ca. 17x more reactive. When both Na37Cl and CuCl2 were added to aqueous extracted fly ash, the percentage of 37Cl from Na37Cl included in PCDD/F increased, compared to the combination of Na37Cl/fly ash. When Na37Cl and CuCl2 were exchanged in water, followed by evaporation of the solvent, and mixed with aqueous extracted fly ash, the percentage of 37Cl included in PCDD/F was much higher. Apparently, direct transfer of 37Cl from CuCl2 to carbon and PCDD/F was much faster than transfer of 37Cl- from Na37Cl via a metal chloride (such as CuCl2) to carbon and PCDD/F. In addition to chlorine in PCDD/F originating from exchanged NaCl/CuCl2, chloride left on the fly ash after aqueous extraction and chlorine present in residual carbon could also have been incorporated in PCDD/F.     

The formation of polychlorinated dibenzo-p-dioxins/dibenzofurans from carbon model mixtures containing ferrous chloride

The potential to form polychlorinated dibenzo-p-dioxins/furans (PCDD/F) was investigated in carbon model systems containing ferrous chloride tetrahydrate and a matrix representative of that found in particle emission from the catalytic extraction process (CEP) for wastes. Various types of carbons were used resulting in different PCDD/F yields but, with one exception, similar homologue distributions. Due to the similarity between the turbostratic structure of the carbon in the representative CEP dusts and the carbon blacks used in the model system, experiments were performed using two carbon blacks (termed CBA and CBB). On a mass basis, CBB was more reactive over the temperature range of 275-325 degrees C and reaction times of 20-60 min in the formation of PCDD/F; as well as more adsorptive in terms of the desorption of PCDD/F. On a volume basis, the reactivities and adsorptivities were similar. A maximum in PCDD/F formation occurred at an oxygen concentration of 2% in nitrogen.     

The influence of level and chlorine source on the formation of mono- to octa-chlorinated dibenzo-p-dioxins, dibenzofurans and coplanar polychlorinated biphenyls during combustion of an artificial municipal waste

The formation of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and the three coplanar polychlorinated biphenyls (pPCBs) was studied during labscale fludized bed combustion of eight artificial municipal solid waste (MSW) fuel mixtures. The level of chlorine as well as the chlorine source varies within the different fuel mixtures. Four different chlorine sources were studied, viz, an inorgnaic (NaCl) and three organic sources, pure PVC plastic and two products (floor and cable) and the total chlorine level varies between 0.28% and 1.1%. The experiments were performed in a 5 kW laboratory scale fluidized bed reactor. A correlation between the total chlorine in the fuel and the formation of the hepta- and octa-chlorinated PCDD/F homologues was found. However, the most important variable for changes in the PCDDs/Fs and pPCBs formation was disturbance in the combustion condition and not the variation in chlorine content of the fuel. Furthermore, no differences in formation between the chlorine sources could be seen.     

Long-term monitoring and modeling of polychlorinated dibenzo-p-dioxins and dibenzofurans from municipal solid waste incinerators and surrounding area in northern Taiwan

Municipal solid waste incinerators (MSWIs) have long been the major contributors of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) to ambient air in Taiwan. After stringent MSWI emission standards were introduced in 2001, the long-term continuous monitoring of flue gas and ambient air quality became necessary to ensure the effectiveness of the related control strategies. Three MSWIs and the surrounding ambient air were investigated in the current study for PCDD/F characteristics during 2006 to 2011. The average concentrations in the flue gas ranged from 0.008?~?0.0488 ng I-TEQ/Nm³, which is much less than the emission standard in Taiwan (0.1 ng I-TEQ/Nm³) (I-TEQ is the abbreviation of International Toxic Equivalent). This led to extremely low levels in the ambient air, 0.0255 pg I-TEQ/Nm³, much less than the levels seen in most urban areas around the world. Additionally, the results obtained using the Industrial Source Complex Short-Term Dispersion Model (ISCST3) indicate that the PCDD/F contributions from the three MSWIs to the ambient air were only in the range from 0.164?~?0.723 %. Principal component analysis (PCA) showed that the PCDD/Fs in the air samples had very similar characteristics to those from mobile sources. The results thus show that stringent regulations have been an effective control strategy, especially for urban areas, such as Taipei City.     

Effects of copper chloride on formation of polychlorinated dibenzofurans in model waste incineration in a laboratory-scale fluidized-bed reactor

Combustion experiments in a laboratory-scale fluidized-bed reactor have been performed to clarify the effects of copper chloride as a catalyst on polychlorinated dibenzofurans (PCDFs) formation in municipal waste incineration. We used model wastes with and without copper chloride (CuCl2 x 2H2O) as a catalyst, both of which contained polyvinyl chloride (PVC) as a chlorine source. Combustion temperature was set to 900 degrees C, and the amount of air supplied was twice as much as the theoretical amount. The experimental setup had been carefully planned to ensure avoidance of the influences of previous experiments. Results of these present experiments revealed that copper chloride in the waste increased the amount of PCDFs formed and made the homologue profile shifted towards the highly chlorinated species. Copper chloride contributes to PCDFs formation by promoting chlorination via catalytic reactions, whereby the reaction could be important in that organic matters are chlorinated directly by chlorinated compounds related to Deacon reaction such as copper chloride. It was elucidated that characteristic isomer distribution patterns appeared in case the waste contained copper chloride. It is probable in our experiment with copper chloride that PCDFs are mainly formed via catalytic reactions of copper compounds and carbon.     

Dechlorination ability of municipal waste incineration fly ash for polychlorinated phenols

Pathways of pentachlorophenol dechlorination have been investigated on municipal waste incineration fly ash at 200 degrees C under nitrogen atmosphere. Thermodynamic calculations have been carried out for these dechlorination conditions using the method of total Gibbs energy minimization for the whole system consisting of gaseous components, i.e., chlorinated phenols, phenol, hydrogen chloride and the Cu3Cl3 trimer and of solid Cu2O and CuCl2 components. The effects of water, temperature and of the amounts of the reaction components on the thermodynamic equilibrium have been discussed and the experimental results compared with the calculated thermodynamic data.     

Evaluation of the leachability of polychlorinated dibenzo-p-dioxins and dibenzofurans in raw and solidified air pollution control residues from municipal waste incinerators

Leachability of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) from raw and solidified air pollution control (APC) residues with selected solvents, including acetic acid, simulated acid rain, humic acid, linear alkylbenzene sulfonate (LAS) and n-hexane was investigated. High-chlorinated PCDD/F congeners were observed in all leachates of raw APC residue samples, with the largest total leaching concentration (61.60 ngm(-3); 0.30 ngI-TEQm(-3)) from treatment with humic acid. Low-chlorinated congeners were mainly leached with LAS and n-hexane. Solidification and stabilization (S/S) processes with cement and sulfur-containing chelating agent decreased the leachability of PCDD/Fs by up to 98% with humic acid and LAS as solvents. However, S/S processes enhanced the leachability of both high- and low-chlorinated PCDD/F congeners with n-hexane as the solvent, which largely increased the toxic equivalent quantity of leachates. These results suggest that conventional S/S processes may effectively restrain the release of PCDD/Fs when APC residues are leached with rain water or natural organic compounds (e.g., humic acid), but may have a deteriorated effect when APC residues are leached with nonpolar organic solvents (e.g., n-hexane) coexisting in the landfill sites.     

Isomer dependent bioavailability of polychlorinated dibenzo-p-dioxins and dibenzofurans from municipal incinerator fly ash to carp

The isomer dependent bioavailability of PCDDs and PCDFs from municipal incinerator fly ash to freshwater fish was determined. It was observed that carp exposed to fly ash in a continuous flow exposure readily accumulated select isomers of PCDDs and PCDFs. A preference for greater retention of isomers substituted in the 2, 3, 7 and 8 positions was observed. The Bioavailability Index (ratio of contaminant level in fish to level in fly ash) decreased with increasing degree of chlorination.     

Depositional flux of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans in an urban setting

Dry and wet deposition fluxes of the PCDD/F substituted congeners were measured at two different sites (Clinton Drive and Lang Road) in Houston, TX between December 2003 and April 2004. Average total dry deposition fluxes of 351 and 125pgm(-2)d(-1) were found at Clinton Drive and Lang Road, respectively. A wet deposition flux of 2.873pgm(-2)d(-1) was measured at the Clinton Drive site. The results indicated that the dry deposition process exhibited spatial variability. In addition, the results also demonstrated that precipitation, although intermittent, is the most important mechanism for the removal of dioxins from atmosphere in the area of study. Combining the contributions of the dry and wet deposition processes at Clinton Drive resulted in a total bulk deposition flux of 527pg m(-2)d(-1). The total dry and wet deposition fluxes were dominated by OCDD followed by 1,2,3,4,6,7,8-HpCDD at both sites. Overall average dry deposition velocities of 0.35 and 0.15cms(-1) were calculated at Clinton Drive and Lang Road sites, respectively. While these velocities were similar to velocities observed in other geographical areas, the contribution of OCDD to the total deposition flux in Houston was significantly higher, probably reflecting the unique nature and character of Houston dioxin sources. The results also showed that lower chlorinated congeners, primarily present in the gas phase, are more likely to be removed from the atmosphere by precipitation. Relationships between the detected congeners in the dry deposition samples and other routinely measured air pollutants/meteorological parameters were found. The results showed that in general, the dry deposition of these congeners was consistently negatively correlated with SO(2) and NO(x) concentrations in the air and positively correlated with relative humidity. However, more research is needed to ascertain those correlations.     

Alumina as a model support in the formation and dechlorination of polychlorinated dibenzo-p-dioxins and dibenzofurans

Alumina was studied as a model matrix for formation and dechlorination reactions of PCDDs and PCDFs. Only small differences in PCDD and PCDF formation were found between de-novo synthesis on alumina and on fly ash. The amounts of PCDDs and PCDFs formed on acidic alumina were much larger than on neutral and alkaline alumina. OCDD and OCDF were rapidly dechlorinated on basic alumina.     

Mechanism of the formation of polychlorinated dibenzo-p-dioxins and dibenzofurans from chlorophenols in gas phase reactions

The pyrolysis of chlorinated phenates at a temperature of about 280 degrees C results in the formation of definite chlorinated dibenzodioxin (PCDD) congeners [1-3]. It is shown that in gas phase reactions chlorophenols react in the presence of oxygen above 340 degrees C not only to PCDD but also to chlorinated dibenzofurans (PCDF). The mechanism of this reaction of chlorophenols to PCDD and PCDF was elucidated. In a first step phenoxyradicals are formed which are capable of forming PCDDs and PCDFs. This is confirmed by the oxygen dependency of the reaction. In an argon atmosphere no dimerization of chlorophenols could be observed at 420 degrees C. By the identification of intermediates and by analyzing the PCDF isomers formed from individual chlorophenols the reaction pathway is elucidated. As intermediates in the formation of PCDFs polychlorinated dihydroxybiphenyls (DOHB) were identified. These are most likely formed by the dimerization of two phenoxy radicals at the hydrogen substituted carbons in ortho-positions under simultaneous movement of the hydrogen atoms to the phenolic oxygen PCDDs are formed in the gas phase via ortho-phenoxyphenols (POP) analogous to the pyrolysis of phenates, but due to the radical mechanism in the first condensation step to POPs not only a chlorine atom is capable for substitution but also the hydrogen atoms. The formation of the DOHBs and their condensation to PCDFs and hydroxylated PCDFs as well as the ratio of PCDD to PCDF formed show a strong dependency on the reaction temperature, the substitution pattern of the chlorophenols and the oxygen concentration.     

Emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans from various industrial sources

This study characterized the emissions of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) from the stack flue gases of 17 industrial sources, which were classified into 10 categories. The results show that the mean PCDD/PCDF concentration of secondary zinc smelter (Zn-S) and secondary copper smelter (Cu-S) is 2.44 ng international toxic equivalent (I-TEQ)/Nm3 (N represents normal conditions at 0 degrees C, 760 mmHg), which was found to be significantly greater than that of industrial waste incinerators (mean concentration = 0.15 ng I-TEQ/Nm3). These results imply that the controlling of secondary metallurgical melting processes is more important than industrial waste incineration for the reduction of PCDD/PCDF emissions. The mean emission factors of cement production, Zn-S and Cu-S, are 0.052, 1.99, and 1.73 microg I-TEQ/t product, respectively. For industrial waste incineration, the mean emission factors of waste rubber, waste liquor, waste sludge, industrial waste solid (IWI)-1, IWI-2, IWI-3, and IWI-4 are 0.752, 0.435, 0.760, 6.64, 1.67, 2.38, and 0.094 microg I-TEQ/t feed, respectively. Most of the PCDD/PCDF emission factors established in this study are less than those reported in previous studies, which could be because of the more stringent regulations for PCDD/PCDF emissions in recent years.     

Polychlorinated dibenzo-p-dioxins, dibenzofurans and 'dioxin-like' PCBs in flue gas emissions from municipal waste management plants

The aim of this work is to give representative data on polychlorinated dibenzo-p-dioxins (PCDD), polychlorinated dibenzofurans (PCDFs) and polychlorinated biphenyl (PCBs) from stack gas emissions of an urban solid waste management plant which has to comply with the limit of 0.1 ng I-TEQ/Nm3. In particular, the study is focused on 29 target compounds, the seventeen 2,3,7,8-PCDDs/Fs, four non-ortho PCBs and eight mono-ortho PCBs which configure so-called 'dioxin-like' PCBs (DL-PCBs). To this end, emission measurements were performed during one year over the three operating combustion lines in a selected waste management plant. In general, accurate methodology allowed characterizing all target compounds in almost all the samples analyzed. In addition, a typical pattern for DL-PCBs is reported. The pattern presented PCB #118 to be the highest, nevertheless the figures demonstrated DL-PCBs contribution to the total TEQ around 3% being PCB #126 the most important congener due to its TEF of 0.1. Finally, remarkable differences were achieved in comparison with both environmental and biological samples such as soils, sediments, human milk or fish since these matrices may present DL-PCB contribution to the total TEQ up to 77%.     

Effects of copper chloride on formation of polychlorinated dibenzo-p-dioxins in model waste incineration

Combustion experiments in a laboratory-scale fluidized-bed reactor were conducted to elucidate the effects of copper chloride as a catalyst on polychlorinated dibenzo-p-dioxins (PCDDs) formation in municipal waste incineration. We used model wastes with and without copper chloride (CuCl₂ · 2H₂O), both of which contained polyvinyl chloride as a chlorine source. Combustion temperature was set to 900 °C, and the amount of air supplied was twice the stoichiometric ratio. The experimental setup was carefully planned to suppress the influences of experimental conditions except the waste composition. Results of these experiments showed that copper chloride in the waste increased the amount of PCDDs formed and made the homologue profile to shift towards the highly chlorinated species. Copper chloride contributes to the PCDDs formation by promoting chlorination, whereby the reaction is important in that organic matter is chlorinated directly by copper compounds. Copper chloride did not exert a great influence on the isomer distribution patterns of PCDDs, while there appeared a significant difference in the case of PCDFs. This points out the difference of the major formation mechanisms between PCDDs and PCDFs. PCDDs are less formed by the catalytic reactions from carbon/polycyclic aromatic hydrocarbons than PCDFs in our experimental conditions.