Quecksilbergasfeinreinigung mittels metall- und salzpartikelbelegter Trägermaterialien (G/S-Reaktor) Ökotoxizität von Quecksilber und seiner Verbindungen

Waste and process gases from thermal power and metallurgical plants or such products from alkali-chloride industries contain metallic, inorganic and organic mercury. Widespread processes applied to remove the greatest amount of mercury are absorption and adsorption. Caused by the lowering of the emission limit from 200 to 50 µg/m³ [STP] by national and European legislators, considerable efforts have been made to enhance the efficiency of the main separation units of flue gas cleaning plants by applying the appropriate technological measures. This article is focused on the removal of mercury from waste gases. The state of engineering is described, especially with regard to enhancing the efficiency of separation in the raw gas, in wet, dry and quasi-dry processes as well as in tail-end process units. Specially impregnated ceramic carriers can be used for the selective separation of metallic, inorganic and organic mercury. Amalgamation has been investigated as a possible separation mechanism both experimentally and in theory. Using the ceramic reactor, removal rates for gaseous mercury and its compounds can be achieved which are even lower than 50 µg/m³ [STP]. The technology, the separation mechanisms and the ecological advantages through the use of ceramic reactors are presented in the article as well.     

PCDD/PCDF-Bodengehalte im Umfeld von Verbrennungsanlagen

In connection with law-imposed waste disposal regulations concerning the modernisation of the incineration ?Munich-North“, local authorities and residents raised objections. Based on an immission calculation using a numerical model concerning the impact of PCDD/PCDF on the soil (study I), conclusions were drawn that the former immissions were so high that further impact on the soil by a new combustion plant was no longer tolerable. The results of study I were controlled using a different numerical model calculation (study II). The simulation results varied vastly because of the differences in preliminary input parameters. In order to verify the simulations, soil samples were taken and the content of PCDD/PCDF was determined. Predicted soil-contents of study II were in the same range as the analyzed samples, whereas the values of study I were higher. With one exception, the soil contents were less than 5 ng TEQ-BGA kg^?1 m_T, a value below the BGA limits. Calculations by numerical modelling, compared to the measurement of PCDD/PCDF soil contents, are therefore no reliable basis for predicting PCDD/PCDF concentrations in soils which has been induced by incineration emission.     

Ecotoxicological assessment of sediment from Texcalac River and agricultural soil of riverside area,in Tlaxcala,Mexico

This study assesses the potential risk of Texcalac River and riparian area. The p,p′ DDT and ∑DDTs levels in agricultural soils (3.9–208.0?µg/kg) and in surface sediments (0.6–137?µg/kg) surpassing the guidelines for protection of aquatic life (75% > TEC). The ∑PCBs concentration oscillated from 135 to 93941?µg/kg; the half of sediments exceeded the international guidelines (PEL, PEC), as well as two soils (SQGE?=?500?µg/kg). The TEQ concentration of four PCB-DL varied between 0.1 and 24.9?µg TEQ/kg, chiefly affected by PCB 169. Five sediments were lethal for E. foetida, two resulted to be cytotoxic and the 58% produced genotoxicity higher than negative control (A?=?0.28?±?0.05; DICA?=?72.5?±?16.9 au). Likewise, 31.6% of samples increased the micronuclei frequency in V. faba in comparison with negative control. The analytical data and the bioassays results suggest a significant and immediate risk to exposed biota of this region, highlighting a specific area in Texcalac River and other one in Sambrano Ravine. It is necessity assess the dispersion of pollutants and perform biomonitoring studies that display the exposure levels in biota with the goal to characterise the ecotoxicological risk.     

Distribution of mercury in the sediments of some freshwater bodies in Ethiopia

Sediment samples were collected from Tinishu Akaki River (TAR), Lake Awassa, and Lake Ziway, Ethiopia for determination of mercury. The air-dried samples were analyzed for mercury with a differential atomic absorption spectrometer after thermal evaporation of bound mercury converting it to its atomic form. Certified reference materials (CRMs) of sediments and soils were used to validate the method. The recovery of mercury from CRMs and sediments was in the range of 95–100%. The limit of detection for the determination of mercury was 50?ng?kg^?1. The concentration of total mercury in the sediments varied from 3.9 to 110?µg?kg^?1 for TAR, 14 to 67?µg?kg^?1 for Lake Awassa, and 17 to 110?µg?kg^?1 for Lake Ziway. It was found that the total mercury concentrations in all samples were below the United States Environmental Protection Agency guideline of 200?µg?kg^?1.     

Teil 1: PCDD/F in Böden,Vegetation und Kuhmilch

Soil samples were taken from residential gardens, grasslands and forests at 22 locations in Marsberg, North Rhine-Westphalia, and analyzed for PCDD/F. Sampling was concentrated on the vicinity of a former copper smelter where copper waste material (calledKieselrot) was deposited and emissions from former stacks contaminated a large land area. Maximum PCDD/F-concentrations were 407 ng TE GBA/kg dm in garden soil (0–30 cm depth), 98 ng TE BGA/kg dm in agricultural grassland (0–10 cm depth), 227 ng TE BGA/kg dm in wasteland, and up to 8073 ng TE BGA/kg dm in forest soils. PCDD/F-levels in soil decreased with increasing distance from the former sources providing a large historic emission problem, apart from the still existing kieselrot waste site. Ash residues from former flue gas duct showed up to 2,4 mg TE BGA/kg dm. PCDD/F-concentrations in vegetable samples from highly contaminated garden soils and grass from agricultural grassland were found to be relatively low in relation to soil values. PCDD/F-levels in salad showed a mean of 2,2 ng TE BGA/kg dm while grass concentrations were <6 ng TE BGA/kg dm. Thus, no correlation was found between soil and vegetation values with the exception for carrot roots where obviously a small transfer of PCDD/F between the two media took place. PCDD/F-content in grass taken over the vegetation period showed a tendency to increase toward the end of the growing season, which is probably related to changes in the dry matter yield over the season. No correlation was found in general between soil, grass and milk PCDD/F contents when all samples were taken from the same grassland. PCDD/F-concentrations in milk ranged between 0,6 and 1,1 pg TE BGA/g milkfat and were thus in the same range as consumer milk in the Federal Republic of Germany. PCDD/F in needles from conifers showed a clear relationship with respect to distance from the former waste site. The relatively high levels in conifer needles [36 ng TE BGA/kg dm] were obviously due to sporting activities (i.e. motocross racing where contaminated material was resuspended and deposited on surrounding trees).     

Source attribution for mercury deposition with an updated atmospheric mercury emission inventory in the Pearl River Delta Region,China

Estimated anthropogenic Hg emission was 11.9 tons in Pearl River Delta for 2014. Quantifying contributions of emission sources helps to provide control strategies. More attentions should be paid to Hg deposition around the large point sources. Power plant, industrial source and waste incinerator were priorities for control. A coordinated regional Hg emission control was important for controlling pollution. We used CMAQ-Hg to simulate mercury pollution and identify main sources in the Pearl River Delta (PRD) with updated local emission inventory and latest regional and global emissions. The total anthropogenic mercury emissions in the PRD for 2014 were 11,939.6 kg. Power plants and industrial boilers were dominant sectors, responsible for 29.4 and 22.7%. We first compared model predictions and observations and the results showed a good performance. Then five scenarios with power plants (PP), municipal solid waste incineration (MSWI), industrial point sources (IP), natural sources (NAT), and boundary conditions (BCs) zeroed out separately were simulated and compared with the base case. BCs was responsible for over 30% of annual average mercury concentration and total deposition while NAT contributed around 15%. Among the anthropogenic sources, IP (22.9%) was dominant with a contribution over 20.0% and PP (18.9%) and MSWI (11.2%) ranked second and third. Results also showed that power plants were the most important emission sources in the central PRD, where the ultra-low emission for thermal power units need to be strengthened. In the northern and western PRD, cement and metal productions were priorities for mercury control. The fast growth of municipal solid waste incineration were also a key factor in the core areas. In addition, a coordinated regional mercury emission control was important for effectively controlling pollution. In the future, mercury emissions will decrease as control measures are strengthened, more attention should be paid to mercury deposition around the large point sources as high levels of pollution are observed.     

Reagenzienfreie Bestimmung von Quecksilberspuren in Wasserproben

A comprehensive ecological monitoring of hazardous substances is indispensable to preserve our health and environment. Therefore, fast and inexpensive techniques for routine analysis of pollutants are essential. However, in the measuring procedure itself often toxic reagents are used producing hazardous waste. Omitting environmentally hazardous substances in the analysis procedure is an important contribution to a more sustainable and green analytical chemistry. A reagent-free method for ultra-trace (pg to ng?L^-1) mercury determination in water samples was developed and validated. An active nanogold collector integrated in a fully automated flow injection system is the core of this new method. All mercury species dissolved in the water sample are adsorbed and preconcentrated on the nano-structured gold surface of the collector. After rinsing and drying of the collector, the enriched mercury is thermally desorbed and finally measured by atomic fluorescence spectrometry. This method was optimized and validated for the determination of mercury in natural waters. The influence of various water constituents was investigated and only high contents of dissolved organic carbon (DOC) showed interferences of mercury preconcentration due to the strong complexation of mercury by DOC. This restriction can be solved by UV-irradiation, i.?e. reagent-free digestion of DOC rich samples prior to the preconcentration procedure. Mercury concentration of several natural river and sea waters and water from the discharge of a waste water treatment plant were determined with this new analytical method. Accuracy and precision of the method were demonstrated by several recovery experiments in natural water samples (recoveries: 96–102?%) and by analysis of the certified reference material BCR-579 (Mercury in Coastal Sea Water; recovery: 101?±?1?%). With a detection limit of only 80?pg?Hg?L^–1 the proposed method is highly sensitive. Furthermore the method avoids potential contamination of the sample by reagent addition and is due to the reagent-free procedure environment-friendly. Hence this work is an important contribution to sustainable environmental analysis and at the same time improves accurate routine mercury trace analysis.     

An Operationally Defined Method to Determine the Speciation of Mercury

This paper presents a modified method of an operationally determined speciation of mercury in soil. The analytical work was mainly concerned to suit properly with inductively coupled plasma-atomic emission spectrometry (ICP-AES). Soil samples analysed in this study were selected from open areas around a crematorium, a waste incinerator, and two power plants. Results show that both topsoil and subsoil samples were dominated by elemental mercury Hg(0) and mercuric sulphide (HgS). The significant correlation between sulphur concentration and HgS was found in topsoil samples.     

Mercury concentrations in the surface sediments of the intertidal area along the west coast of Peninsular Malaysia

Total mercury (Hg) levels in the intertidal surface sediments along the west coast of Peninsular Malaysia were analysed by using heat vaporization method. Total Hg levels in these sediments ranged from 3.00 to 201?µg?kg^?1 dry weight with a mean concentration of 60.0?µg?kg^?1 dry weight. More than 90% of the samples studied have the total Hg concentrations less than 150?µg?kg^?1 dry weight. Compare with the regional data and sediment quality guidelines, the Hg contamination in the intertidal area along the west coast of Peninsular Malaysia was not serious, except for a few sites that might have received anthropogenic Hg in the samples collected between 1999 and 2000. It is suggested that a similar study of heavy metals in the sediments of the west coast of Peninsular Malaysia be conducted regularly.     

Effects of industrial waste water on heavy metal accumulation, growth and biochemical responses of lettuce (Lactuca sativa L.)

The waste water showed high values of total solid (TS), hardness and chloride with slightly alkaline pH along with high concentrations of Cr (2.03 mg l(-1)), Ni (1.59 mg l(-1)) and Zn (0.46 mg l(-1)). The concentration of Cu (0.21 mg l(-1)) and Zn in industrial waste water was low than Ni and Cr. The diluted (25 and 50%), undiluted (100%) waste water was used to irrigate the lettuce plants grown in alluvial soils. Plants accumulated heavy metals in their shoot (Ni, 13.65; Cr, 19.73; Zn, 21.6 and Cu 14.76 microg g(-1) dry weight) and root (Ni, 41.4; Cr, 31.6; Zn, 30.2 and Cu 15.85 microg g(-1) dry weight) in high concentrations after irrigation with undiluted industrial waste water. Maximum accumulation of heavy metals was found in the root than the shoot (13.65-21.60 microg g(-1) dry weight). Dry matter yield and biomolecules (Chlorophyll a, b and sugar contents) was found to increase with increase in concentration of waste water up to 50%, which declined at the exposure of undiluted waste water. Catalase activity was found to increase with increase in waste water concentrations up to 100%, while carotenoids content increased in plants only up to the 50% waste water irrigation. Use of industrial waste water in such form, on agricultural lands is not found suitable without proper treatment. It could be injurious to plants growth and may be a potential threat to food web.     

Mercury contamination and health risk to crops around the zinc smelting plant in Huludao City,northeastern China

The Huludao zinc plant in Liaoning province, northeast China was the largest in Asia, and its smelting activities had seriously contaminated soil, water and atmosphere in the surrounding area. For the first time, we investigated the total mercury (THg) content in maize, soybean, broomcorn, 22 vegetables, and the soil around their roots from eight sampling plots near the Huludao zinc plant. THg contents of the seeds of maize, soybean, and broomcorn are 0.008, 0.006, and 0.057 mg kg⁻¹, respectively, with the broomcorn being the highest, exceeding the maximum level of contaminant in food (GB2762-2005) by 4.7 times. The edible parts of vegetables are also contaminated with a range of mercury contents of 0.001–0.147 mg kg⁻¹ (dry weight). THg contents in plant tissue decrease in the order of leaves > root > stalk > grain. Using correlation analysis, we show that mercury in the roots of these plants is mainly derived from soil, and the uptake of gaseous mercury is the predominant path by which the mercury accumulated in the foliage. The average and maximum mercury daily intake (DI) of adult around the Huludao zinc plant via consuming vegetables are 0.015 and 0.051 μg/kg/d, respectively, and those of children are 0.02 and 0.07 μg/kg/d, respectively. The average and maximum weekly intakes of total mercury for adult are 2.1 and 7.1%, respectively, of the provisional tolerable weekly intake (PTWI), and 2.8 and 9.7%, respectively, of the PTWI for children.     

Exposure assessment for mercury from consumption of marine fish in Iran

Seven species of marine fish in the Persian Gulf and three species of marine fish in the Caspian Sea were collected from the local wholesale market in Mashhad, Iran. The mercury (Hg) concentration in muscle samples was determined by atomic absorption spectrophotometry. High total Hg concentration was found in Anchovy sprat (2.04 ± 1.23 µg g^?1) and Whitecheek shark (1.26 ± 1.85 µg g^?1) and the lowest content was detected in common carp (0.24 ± 0.24 µg g^?1) and Caspian salmon (0.25 ± 0.08 µg g^?1). The mean Hg content in all samples was 0.91 ± 1.07 µg g^?1. All samples of Persian Gulf and one sample of Caspian Sea had mean Hg concentration above 0.5 µg g^?1, the level established by joint FAO/WHO on Food Additives. Results showed that the estimated weekly intake of total Hg by a 60 kg adult is below the provisional tolerable weekly intakes recommended by joint FAO/WHO on Food Additives. For prevention of health risks, populations in Iran need to consume fish in moderate amounts.     

Concentrations of polycyclic aromatic hydrocarbons in soils of a mangrove forest affected by forest fire

Surface soils affected by forest fires from Igbanko mangrove forest in Nigeria were analyzed for 16 EPA priority polycyclic aromatic hydrocarbons (PAHs) using gas chromatography–mass spectrometry (GC–MS). The total PAHs concentrations in the soils ranged from 63 to 188?µg?kg^?1 dry weight (average: 108?µg?kg^?1). The three predominant PAHs in the soils were naphthalene (Na), fluoranthene (Flu), and benzo(b)fluoranthene (BbF). Compared to the control sample (19?µg?kg^?1), elevated PAHs concentrations were observed in the soils, an indication of some level of PAHs contamination. PAHs source diagnostic ratios of Flu/(Flu?+?Pyr) and Ant/(Ant?+?Phe) indicated that the PAHs have a pyrogenic origin which may have resulted from combustion of grass, wood, or coal. An assessment based on Canadian soil quality guidelines indicated that the studied locations do not pose any serious adverse risk on human health.     

Total and methyl mercury in small marine biota caught off the Coast of Chennai,India

Abstract

This study reports the concentrations of total mercury and methyl mercury in sixteen families of marine biota caught off the coast of Kasimedu in Chennai, India, an important but understudied fish landing region. These included the commonly caught croakers, carangids, rays, goat fish, anchovies, crabs, and prawns. There was no correlation between total mercury or methyl mercury with fish length or mass. All concentrations were lower than the Food Safety and Standards Authority of India limits (total mercury = 500?μg/kg; methyl mercury = 250?μg/kg). Some values were above screening levels (total mercury >40?μg/kg wet weight) when considering possible adverse effects in predatory fish that consume the analyzed biota.

Abbreviations: dw: dry weight; MeHg: methyl mercury; THg: total mercury; ww: wet weight     

北京市农业区不同使用类型土壤中二噁英类分析

2005年6—7月采集了北京市农业区不同使用类型土壤样品24个,分别为蔬菜地8个、粮地8个、果园地8个,采用高分辨气质联机对17种二噁英类进行了分析.结果表明:所有样品中二噁英浓度范围为,0.26—5.74(平均值为1.51)pgI-TEQ.g-1;蔬菜地浓度范围为,0.26—5.62(平均值1.75)pgI-TEQ.g-1;粮地浓度范围为,0.45—5.74(平均值2.02)pgI-TEQ.g-1;果园地浓度范围为,0.34—2.02(平均值0.73)pgI-TEQ.g-1;三种类型中粮食地浓度最高,其次为蔬菜地,果园地浓度最低.与国外农业区土壤中的二噁英浓度相比而言,北京市相对较低.所有样品中,样品8和16浓度异常高,但是8.3%(2:24)的高浓度样品数并不代表对人体有害.由于样品24处于垃圾焚烧炉旁边,也对此进行了详细的分析.样品中二噁英类物质形态分布出现了极大的离散性,这表明农田土壤中二噁英可能是多种因素综合作用的结果,例如:除草剂的使用、秸秆等固体废弃物的焚烧、汽车尾气排放等.     

Quecksilbergasfeinreinigung mittels metall- und salzpartikelbelegter Trägermaterialien (G/S-Reaktor) Ökotoxizität von Quecksilber und seiner Verbindungen

Waste and process gases from thermal power and metallurgical plants or such products from alkali-chloride industries contain metallic, inorganic and organic mercury. Widespread processes applied to remove the greatest amount of mercury are absorption and adsorption. Caused by the lowering of the emission limit from 200 to 50 μg/m³ [STP] by national and European legislators, considerable efforts have been made to enhance the efficiency of the main separation units of flue gas cleaning plants by applying the appropriate technological measures. This article is focused on the removal of mercury from waste gases. The state of engineering is described, especially with regard to enhancing the efficiency of separation in the raw gas, in wet, dry and quasi-dry processes as well as in tail-end process units. Specially impregnated ceramic carriers can be used for the selective separation of metallic, inorganic and organic mercury. Amalgamation has been investigated as a possible separation mechanism both experimentally and in theory. Using the ceramic reactor, removal rates for gaseous mercury and its compounds can be achieved which are even lower than 50 μg/m³ [STP]. The technology, the separation mechanisms and the ecological advantages through the use of ceramic reactors are presented in the article as well.     

Bioconcentration factors of mercury by Parasol Mushroom (Macrolepiota procera)

To examine bioconcentration factors (BCFs) of mercury by Parasol Mushroom (Macrolepiota procera) roughly similarly sized (a cap diameter) fruiting bodies of this fungus and underlying soil (0–10 cm) samples were collected at 15 sites in Poland between 1995 and 2003. The total mercury content of the individual caps and stipes of Parasol Mushroom ranged from 0.05 to 22 mg Hg/kg dry matter (d.m.) and from 0.05 to 20 mg Hg/kg d.m., while the means were from 1.1 to 8.4 mg Hg/kg d.m. and from 0.83 to 6.8 mg Hg/kg d.m., respectively. The caps generally contained higher concentrations of mercury when compared to stipes, and the means of the cap to stipe mercury concentration quotient ranged from 1.3 to 4.6. The range of mercury concentration in topsoil samples collected at the sites where the fruiting bodies were collected was from 0.01 to 0.54 mg/g d.m. (means ranged from 0.022 to 0.36 mg/g d.m.). The BCFs factors for total mercury varied from 0.52 to 470 for individual caps and 0.52 to 360 for stipes, while average values, depending on the site, were from 16 to 220 and from 7.6 to 130 for caps and stipes, respectively.     

Determination of persistent organic pollutants by gas chromatography/laser multiphoton ionization/time-of-flight mass spectrometry

An authentic mixture of polychlorinated biphenyls was measured using a short wide-bore capillary column for the group separation of major components present in an actual sample of Kanechlor. The limits of detection were improved by ca. 2 fold in comparison with those obtained using a conventional capillary column, since the retention time was reduced and the amount of analytes introduced into the mass spectrometer per unit time could be increased. On the other hand, surface-water and sediment samples containing polycyclic aromatic hydrocarbons (PAHs) were collected from the river located in the vicinity of a waste water treatment plant. Even acenaphthylene, a minor component of the mixture could be measured for the sediment sample, and the concentrations were determined for several heavy PAHs. As demonstrated, a technique involving laser multiphoton ionization/time-of-flight mass spectrometry was useful as a sensitive and selective analytical tool for the trace analysis of persistent organic pollutants in an environmental sample.     

Analysis of the cyanotoxins anatoxin-a and microcystins in Lesser Flamingo feathers†

Feathers from carcasses of the Lesser Flamingo (Phoeniconaias minor), which had died after ingesting cyanobacterial toxins (cyanotoxins) contained between 0.02 and 30.0?µg microcystin-LR equivalents per gram of feather according to HPLC and ELISA analysis of feather extracts. Anatoxin-a was detected less frequently in the Lesser Flamingo feathers, up to 0.8?µg anatoxin-a per gram of feather being recorded. When feathers from different body regions were analysed and compared for microcystins and anatoxin-a, wing feathers were found to contain the highest concentrations of these cyanotoxins, the order of concentration and frequency of analytical detection being wing?>?breast?>?head. Consistent with the presence of the microcystins and anatoxin-a in gut contents and the livers of the dead birds and negligible in vitro adsorption to feathers, the cyanotoxins associated with the feathers of the dead wild flamingos are inferred to be primarily of dietary origin.     

广州市菜园土主要蔬菜重金属背景含量的研究

研究了广州市几个主要的蔬菜生产基地种植的白菜、芥蓝、芥菜、菜薹、萝卜、大白菜、豆瓣菜、结球甘蓝、芹菜、菜豆、豌豆、结球莴苣、尖叶莴苣、菠菜、番茄等15种蔬菜中Pb、Hg、Cd、Cr和As等5种重金属的背景质量分数。其背景质量分数为：Pb 0．002～0．148mg/kg；Hg ND-0．006mg/kg；Cd 0．001～0．034mg/kg；Cr 0．002～0．150mg/kg；As 0.001～0．070mg／kg。由于不同种类蔬菜的吸收特性和遗传特性有所不同，其重金属背景质量分数也有很大差异。蔬菜中元素水平还与土壤条件等因素有关。