Ca(OH)2、高岭土与FeCl3组配处理含Pb2+废水

采用Ca（OH）2、高岭土与FeCl3组配处理含Pb^2＋废水。考察了Ca（OH）2加入量、高岭土加入量、FeCl3加入量、废水pH、搅拌转速、沉淀时间等因素对Pb^2＋去除率的影响。在Ca（OH）2加入量50mg／L、高岭土加入量90mg／L、FeCl3加入量13．2mg／L、废水pH7．0～8．0、搅拌转速170r／min、沉淀时间90min的条件下,该法可将废水中金属离子（包括Pb^2＋及少量的Zn^2＋,Cu^2＋,Cr^3＋,Ni^2＋）的质量浓度由42．4mg／L降至1．0mg／L以下,达到了GB18918--2002〈《城镇污水处理厂污染物排放标准》。     

O3氧化法和O3-H2O2氧化法去除水中聚丙烯酰胺

采用O3氧化法和O3-H2O2氧化法去除水中的聚丙烯酰胺（PAM）,分别考察了反应时间、O3质量浓度、n（H2O2）∶n（O3）和溶液pH对PAM去除效果的影响。实验结果表明：O3氧化的最佳操作条件为反应时间30 min、O3质量浓度22.6 mg/L、溶液pH 8.5,O3-H2O2氧化的最佳操作条件为反应时间10 min、O3质量浓度22.6 mg/L、n（H2O2）∶n（O3）=0.1、溶液pH 8.5;在最佳操作条件下,O3氧化和O3-H2O2氧化均可有效降低PAM溶液的黏度和PAM质量浓度,但对COD的去除效果不佳,黏度可降至和蒸馏水相近,PAM的去除率可达80%以上,而COD的去除率分别约为15%和28%;O3-H2O2氧化后的PAM比O3氧化后的PAM更容易被微生物利用,两种氧化预处理方法均有利于后续的生化处理。     

微波-改性活性炭-Fenton试剂氧化法降解水中2,4-二氯酚

以经Fe2（SO4）3溶液浸渍改性的活性炭作催化剂、Fenton试剂作氧化剂,采用微波-改性活性炭-Fenton试剂氧化法降解水中的2,4-二氯酚。考察了改性活性炭加入量、H2O2与Fe^2＋摩尔比、Fenton试剂加入量、微波功率和2,4-二氯酚溶液初始pH对2,4-二氯酚降解效果的影响。在改性活性炭加入量1．0g／L、n（H2O2）：n（Fe^2＋）=16．7（H2O2加入量6．0mmol／L、Fe^2＋加入量0．36mmol／L）、Fenton试剂加入量为6．36mmol／L、微波功率600W、微波辐射时间10min、2,4-二氯酚溶液初始pH为6．0的条件下,2,4-二氯酚降解率和TOC去除率分别可达98．7％和84．0％。     

烟气脱硫溶液中硫酸根的去除

分别采用石灰乳化学沉淀法和低温结晶法去除烟气脱硫溶液中的SO42-。实验结果表明：在室温、CaO溶液质量分数25%的条件下,石灰乳化学沉淀法对SO42-的去除率仅为59.51%,且向溶液中引入了Ca2+,产生的硫酸钙固体废物难以再生利用;采用低温结晶法处理烟气脱硫溶液,在结晶温度7 ℃、结晶时间3 h、NaOH加入量34.8 g/L的条件下,SO42-的去除率为82.04%、滤液中的ρ（Na+）为3.88 g/L。在现场工业应用试验中,采用低温结晶法去除烟气脱硫溶液中的SO42-,平均SO42-的去除率可达70.00%以上,滤液中的ρ（Na+）小于15.00 g/L。该法可有效抑制烟气脱硫溶液中SO42-含量的增加。     

高铁酸钾预氧化-三氯化铁混凝去除水中As3+

采用K2FeO4预氧化-FeCl3混凝联合去除水中的As3+,考察了适宜的K2FeO4预氧化时间、Fe3+和Fe6+加入量,分析了预氧化pH、混凝pH、碳酸盐和腐殖酸浓度对该工艺去除As3+效果的影响.实验结果表明:K2FeO4预氧化的适宜时间为2 min;加入质量浓度为2.4 mg/L的Fe6+和14.0 mg/L的Fe3+能使处理后水样中的As3+浓度符合GB--57492006<生活饮用水卫生标准>(As3+质量浓度小于0.01 mg/L);预氧化pH在4～9范围内,对K2FeO4预氧化-FeCl3混凝去除As3+的效果影响不大;FeCl3混凝阶段适宜的pH为6.0～8.5.碳酸盐对K2FeO4预氧化-FeCl3混凝去除As3+的效果基本没有影响;腐殖酸的存在使As3+的去除率有一定程度的降低.     

Cu^2＋改性活性炭的制备及其去除废水中CN^-的研究

以活性炭为载体负载溶液中的Cu^2＋,Cu^2＋改性活性炭对溶液中CN^-的去除效果较好。cu。’改性活性炭的最佳制备条件：活性炭加入量为1g,质量浓度为5∥L的CuSO。溶液加入量为50mL,溶液pH为4,负载时间为5．0h.在此最佳条件下活性炭的最大Cu^2＋负载量为25．90mg（以每克活性炭计）。Cu^2＋改性后活性炭的CN^-去除率明显提高,由22．10％提高至94．07％。Cu^2＋改性活性炭吸附CN^-的最佳实验条件：溶液pH为12～13,吸附时间为9h。Cu^2＋改性活性炭对CN^-的饱和吸附量为22mg／g。Mg^2＋,K^＋,Ca^2＋,Cl^-,SO4^2-,CO3^2-,AsO3^-对Cu^2＋改性活性炭的CN^-去除率基本没有影响。Cu^2＋改性活性炭的动态吸附实验表明,开始一段时间流出液中CN^-含量几乎为零,远低于国家排放标准（0．5mg／L）。     

用于去除水中Cr6＋的纳米磁铁矿-硅藻土复合物的制备方法

该发明涉及一种用于去除水中Cr6＋的纳米磁铁矿-硅藻土复合物的制备方法。具体为：在室温按比例混合同等浓度的0．02～0．50mol／L的铁盐-亚铁盐水溶液;加入硅藻土粉末,搅拌均匀;加热,搅拌下缓慢滴加氢氧化铵溶液,使悬浊液pH达8～9后停止滴加;固液分离和漂洗;抽真空、研磨粉碎。利用该发明产品处理废水中的Cr6＋具有成本低廉、高效、操作简便、易于回收等优势,     

碳羟磷灰石的制备及其对水中Cu2+的吸附

以废弃蛋壳为原料、尿素为添加剂,采用掺杂技术制备碳羟磷灰石（CHAP）,并用其作吸附剂去除水中的Cu^2＋。考察了Cu^2＋的初始质量浓度、pH、吸附时间、CHAP加入量及温度等因素对CHAP吸附Cu^2＋效果的影响。实验结果表明,在温度40℃、溶液pH6、搅拌1h后静置1h的条件下,用5g／L的CHAP处理Cu^2＋初始质量浓度为60mg／L的水溶液,Cu^2＋去除率为99．30％。吸附等温线基本符合Freundlich和Langmuir方程。     

羟胺强化Fenton反应降解水中氯酚

针对传统Fenton体系Fe（Ⅲ）累积和pH适用范围过窄等缺点,采用羟胺（HA）强化的HA-Fenton体系,以对氯苯酚（4-CP）为目标污染物进行降解实验,考察了Fe（Ⅱ）投加量、H2O2投加量、HA投加量和溶液pH等工艺条件对4-CP去除率的影响。实验结果表明：HA-Fenton体系适用于酸性和弱酸性条件,最佳pH范围为3.0~4.0;在溶液pH为3.0、Fe（Ⅱ）投加量为5.0 μmol/L、H2O2投加量为0.4 mmol/L、HA投加量为0.20 mmol/L的最适条件下,反应10 min, 4-CP去除率达64.25 %。     

混凝—催化氧化法处理丁苯橡胶生产废水

以聚合氯化铝（PAC）、阴离子聚丙烯酰胺（PAM）为混凝剂,以H2O2-O3为氧化剂,采用混凝-催化氧化法处理对丁苯橡胶生产废水。考察了混凝剂种类及其加入量、废水pH对混凝处理效果的影响,氧化剂及其加入量、反应时间和废水pH对COD去除率的影响。实验得出的最佳工艺条件：混凝实验,废水pH为7、PAC和PAM加入量为400mg／L和4mg／L;催化氧化实验,废水pH为7～8、H2O2加入量为200mg／L、H2O2与O3的质量比为0．5。处理后,废水COD从860mg／L降至145mg／L,COD去除率达83．1％,出水水质达到国家二级排放标准。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6～9,COD 302mg／L,BOD5 108mg／L,SS30mg／L,色度36倍,水质达到GB8978--1996（污水综合排放标准》三级标准。     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Does Soil Acidification Affect Spruce Needle Chemical Composition and Tree Growth?

In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.     

Solubility and Potential Mobility of Heavy Metals in Two Contaminated Urban Soils from Stockholm,Sweden

The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.     

High Immobilization of NH4+ in Danish Heath Soil Related to Succession,Soil and Nutrients: Implications for Critical Loads of N

During recent decades heathlands havechanged into grasslands in regions with high atmosphericnitrogen deposition. In regions with intermediatedeposition level (e.g., Denmark) changes have been lesspronounced which may be due to delay or decrease inresponse of the ecosystem. The mor layer (O horizon) mayplay an important role for this delay due to high sinkstrength for N. In this study, the capacity for netNH₄ ⁺ immobilization and mineralization wasstudied during short- and long-term incubations (2–36 days)of mor samples from Danish dry inland heaths. High short-term capacity for net NH₄ ⁺ immobilization wasfound to be a general characteristic of Danish heath morlayers both under heather (Calluna vulgaris) andcrowberry (Empetrum nigrum ssp nigrum), the latterdominating late stages in heathland succession. The netNH₄ ⁺ immobilization was higher under youngcompared to old or dead vegetation, and higher on lessnutrient poor soils than on extremely nutrient poor soils.The addition of N, P and C stimulated CO₂ productionand net NH₄ ⁺ immobilization, but not net Nmineralization. The immobilization of ¹⁵NH₄ ⁺caused release of dissolved organic N, increased N anddecreased C/N ratio in the microbial biomass, and indicatedgrowth of microorganisms with other metabolic abilitiesthan the indigenous population. No evidence was obtained ofstabilization of immobilized ¹⁵NH₄ ⁺ intosoil organic matter during the experiment. On background ofthe results and current knowledge it was concluded that therecognition of the high capacity for net NH₄ ⁺immobilization in mor layers does not allow for a raiseof critical loads for N for northern dry inland heaths.     

Biodegradation of Injection Molded Starch-Poly (3-hydroxybutyrate-co-3-hydroxyvalerate) Blends in a Natural Compost Environment

Injection molded specimens were prepared by blending poly (hydroxybutyrate-co-valerate) (PHBV) with cornstarch. Blended formulations incorporated 30% or 50% starch in the presence or absence of poly-(ethylene oxide) (PEO), which enhances the adherence of starch granules to PHBV. These formulations were evaluated for their biodegradability in natural compost by measuring changes in physical and chemical properties over a period of 125 days. The degradation of plastic material, as evidenced by weight loss and deterioration in tensile properties, correlated with the amount of starch present in the blends (neat PHBV < 30% starch < 50% starch). Incorporation of PEO into starch-PHBV blends had little or no effect on the rate of weight loss. Starch in blends degraded faster than PHBV and it accelerated PHBV degradation. Also, PHBV did not retard starch degradation. After 125 days of exposure to compost, neat PHBV lost 7% of its weight (0.056% weight loss/day), while the PHBV component of a 50% starch blend lost 41% of its weight (0.328% weight loss/day). PHB and PHV moieties within the copolymer degraded at similar rates, regardless of the presence of starch, as determined by ¹H-NMR spectroscopy. GPC analyses revealed that, while the number average molecular weight (Mn) of PHBV in all exposed samples decreased, there was no significant difference in this decrease between neat PHBV as opposed to PHBV blended with starch. SEM showed homogeneously distributed starch granules embedded in a PHBV matrix, typical of a filler material. Starch granules were rapidly depleted during exposure to compost, increasing the surface area of the PHBV matrix.