给水处理厂铁铝泥对正磷酸盐的吸附效果

通过批量实验和柱状实验并结合磷的分级提取探究了给水处理厂废弃铁铝泥(ferric-alum water treatment re-siduals,FARs)吸附正磷酸盐的效果。批量实验结果表明,Langmuir和Freundlich方程均能较好地描述FARs对磷的等温吸附过程,且当pH从5增至9时,FARs磷的饱和吸附量从41.68 mg/g减小到17.08 mg/g。pH越低,磷与FARs的结合能力越强。柱状实验结果表明,FARs具有显著的磷吸附能力,在运行的89 d里,磷的去除率保持在80%以上。出水pH与进水相比略有增加,但增加量不会对地表水体造成影响。磷的分级提取结果进一步说明,被吸附的磷主要以释磷风险小的铁铝结合态存在。综合实验结果表明,FARs可以作为高效磷吸附剂应用于地表水除磷。     

Adsorption of hydrogen sulfide on montmorillonites modified with iron

Sodium-rich montmorillonite was modified with iron in order to introduce active centers for hydrogen sulfide adsorption. In the first modification, interlayer sodium cations were exchanged with iron. In another modification, iron oxocations were introduced to the clay surface. The most elaborated modification was based on doping of iron within the interlayer space of aluminum-pillared clay. The modified clay samples were tested as hydrogen sulfide adsorbents. Iron-doped samples showed a significant improvement in the capacity for H2S removal, despite of a noticeable decrease in microporosity compared to the initial pillared clay. The smallest capacity was obtained for the clay modified with iron oxocations. Variations in adsorption capacity are likely due to differences in the chemistry of iron species, degree of their dispersion on the surface, and accessibility of small pores for H2S molecule. The results suggest that on the surface of iron-modified clay hydrogen sulfide reacts with Fe(+3) forming sulfides or it is catalytically oxidized to SO2 on iron (hydro)oxides. Subsequent oxidation may lead to sulfate formation.     

高比表面积活性炭的制备及对Cr(Ⅵ)吸附的研究

以椰树壳为原料,运用水蒸汽和二氧化碳复合物理活化法在4 h内制备了2 162.84 m2/g的高比表面积活性炭,其孔径分布范围为1.1~2.5 nm。应用此吸附剂考察了溶液pH、吸附剂用量、接触时间和初始浓度对Cr(VI)离子吸附效果的影响,并讨论了固定吸附床中不同溶液流量对Cr(VI)去除效果的影响。结果表明:在温度为298 K、溶液pH为1.96、吸附剂用量为0.10 g、铬离子初始浓度为100 mg/L与接触时间为70 min的条件下,活性炭对铬离子具有较高的吸附容量,去除率高达99.32%;铬离子在吸附床中的穿透曲线具有陡峭的传质锋面,但随着铬离子溶液流量的增大脱除果率降低。     

Kinetics and the mass transfer mechanism of hydrogen sulfide removal by biochar derived from rice hull

The biochar derived from rice hull was evaluated for its abilities to remove hydrogen sulfide (H₂S) from gas phase. The surface area and pH of the biochar were compared. The biochar derived from rice hull was evaluated for its abilities to remove hydrogen sulfide (H₂S) from gas phase. The surface area and pH of the biochar were compared. The different pyrolysis temperature has great influence on the adsorption of H₂S. At the different pyrolysis temperature, the H₂S removal efficiency of rice hull-derived biochar was different. The adsorption capacities of biochar were 2.09 mg·g^–1, 2.65 mg·g^–1, 16.30 mg·g^–1, 20.80 mg·g^–1, and 382.70 mg·g^–1, which their pyrolysis temperatures were 100 °C, 200 °C, 300 °C, 400 °C and 500 °C respectively. Based on the Yoon-Nelson model, it analyzed the mass transfer mechanism of hydrogen sulfide adsorption by biochar.

Implications: The paper focuses on the biochar derived from rice hull–removed hydrogen sulfide (H₂S) from gas phase. The surface area and pH of the biochar were compared. The different pyrolysis temperatures have great influence on the adsorption of H₂S. At the different pyrolysis temperatures, the H₂S removal efficiency of rice hull–derived biohar was different. The adsorption capacities of biochar were 2.09, 2.65, 16.30, 20.80, and 382.70 mg·g^?1, and their pyrolysis temperatures were 100, 200, 300, 400, and 500 °C, respectively. Based on the Yoon-Nelson model, the mass transfer mechanism of hydrogen sulfide adsorption by biochar was analyzed.     

Photolysis of low concentration H2S under UV/VUV irradiation emitted from microwave discharge electrodeless lamps

The photolysis of simulating low concentration of hydrogen sulfide malodorous gas was studied under UV irradiation emitted by self-made microwave discharge electrodeless lamps (i.e. microwave UV electrodeless mercury lamp (185/253.7 nm) and iodine lamp (178.3/180.1/183/184.4/187.6/206.2 nm)). Experiments results showed that the removal efficiency (eta H2S) of hydrogen sulfide was decreased with increasing initial H2S concentration and increased slightly with gas residence time; H2S removal efficiency was decreased dramatically with enlarged pipe diameter. Under the experimental conditions with pipe diameter of 36 mm, gas flow rate of 0.42 standard l s(-1), eta H2S was 52% with initial H2S concentration of 19.5 mg m(-3) by microwave mercury lamp, the absolute removal amount (ARA) was 4.30 microg s(-1), and energy yield (EY) was 77.3 mg kW h(-1); eta H2S was 56% with initial H2S concentration of 18.9 mg m(-3) by microwave iodine lamp, the ARA was 4.48 microg s(-1), and the EY was 80.5mg kW h(-1). The main photolysis product was confirmed to be SO4(2-) with IC.     

Government Sponsored Air Pollution Research Relating to Agriculture

The absorption of hydrogen sulfide and methyl mercaptan by aqueous solutions of chlorine, sodium hydroxide, and chlorine plus sodium hydroxide was studied using a two-inch diameter absorption column packed with ¼ inch Intalox saddles. Absorption rates were noticeably affected by chemical reactions occurring in the aqueous chlorine and hydroxide media. These solutions were studied as a means of controlling sulfur-containing gas emissions from kraft paper mills. The absorption studies indicated that aqueous chlorine solutions at a pH above 12 were effective absorbents for hydrogen sulfide removal in absorption equipment designed to tolerate sulfur in suspension. The absorption of methyl mercaptan in aqueous chlorine solutions appeared to be impractical since dimethyl disulfide was apparently the only product formed and was stripped from the tower by the gas stream. Sodium hydroxide solution was an effective absorbent for both methyl mercaptan and hydrogen sulfide when hydroxide to sulfide or mercaptan feed ratios were greater than 1 or 1.8, respectively. The mercaptan absorption coefficient was approximately twice that for sulfide absorption.     

Adsorption of hydrogen sulfide by biochars derived from pyrolysis of different agricultural/forestry wastes

The characteristics and mechanisms of hydrogen sulfide (H₂S) adsorption on three different biochars derived from agricultural/forestry wastes through pyrolysis at various temperatures (100 to 500 ºC) were investigated. In this study, the H₂S breakthrough capacity was measured using a laboratory-characterized using pH and Fourier transform infrared spectroscopy analysis. The results obtained demonstrate that all biochars were effective in H₂S sorption. The sorption capacity of the biochar for H₂S removal is related to the pyrolysis temperature and pH of the surface. Certain threshold ranges of the pyrolysis temperature (from 100 to 500 ºC) and pH of the surface are presented. It also concluded that the sorption capacity (for removing H₂S) of rice hull-derived biochar is the largest in three biochars (camphor-derived biochar, rice hull-derived biochar, and bamboo-derived biochar). These observations will be helpful in designing biochar as engineered sorbents for the removal of H₂S.Implications: This paper focuses on the adsorption of hydrogen sulfide (H₂S) by biochars derived from wastes. The characteristics and mechanisms of hydrogen sulfide (H₂S) adsorption on three different boichars derived from agricultural/forestry wastes through pyrolysis at various temperatures were investigated. In this study, the H₂S breakthrough capacity was measured using laboratory characterization with pH and Fourier-transform infrared spectroscopy analysis. The results obtained demonstrate that all biochars were effective in H₂S sorption. The sorption capacity of the biochar for H₂S removal is related to the pyrolysis temperature and pH of the surface.     

Effect of sewer headspace air-flow on hydrogen sulfide removal by corroding concrete surfaces

Hydrogen sulfide adsorption and oxidation by corroding concrete surfaces at different air-flows were quantified using a pilot-scale sewer reactor. The setup was installed in an underground sewer research station with direct access to wastewater. Hydrogen sulfide gas was injected into the headspace of the sewer reactor once per hour in peak concentrations of approximately 500 ppmv. The investigated range of sewer air-flows was representative for natural ventilated sewer systems, and covered both laminar and turbulent conditions. The experiments demonstrated a significant effect of sewer air-flow on the kinetics of hydrogen sulfide removal from the sewer headspace. From the lowest to the highest air-flow investigated, the rate of adsorption and oxidation increased more than threefold. At all air-flows, the reaction kinetics followed a simple n-th order rate equation with a reaction order of 0.8. The effect of air-flow on hydrogen sulfide adsorption and oxidation kinetics was quantified by a simple empirical equation.     

活性炭纤维生物挂膜脱除硫化氢

生物脱硫法作为一种高效、高实用性的除硫新技术而受到越来越多的关注。以活性炭纤维为微生物载体,通过活性污泥上清液挂膜驯化,考察硫化氢进气量、喷淋量、pH值和硫酸根离子浓度等条件对脱硫效率的影响。研究结果表明,在室温下,硫化氢负荷为90 g/(m3.h),进气浓度控制在3 g/m3,进气量为60 L/h,喷淋量为250～650 L/(m3.d),pH为2～5的条件下,生物活性炭纤维对硫化氢的去除率可保持在98%以上。     

Removal of azo dye from water by magnetite adsorption-Fenton oxidation.

The aim of this study is to highlight the possibility of using powder magnetite adsorption-Fenton oxidation as a method for removal of azo dye acid red B (ARB) from water. The adsorption properties of magnetite powder towards ARB were studied. The oxidation of adsorbed ARB and regeneration of magnetite adsorbent at the same time by Fenton reagent (hydrogen peroxide [H2O2] + iron (II) [Fe2+]) in another treatment unit with a smaller volume was also investigated. The efficiency of Fenton oxidation of ARB was compared for the reaction carried out in solution and on magnetite. The magnetic separation method was used to recover magnetite after adsorption or regeneration. The results indicated that the adsorption rate was fast. The capacity was strongly dependent on pH and inorganic anions, and pH 3.8 was optimal for the adsorption of ARB. The adsorption can be described well using the Langmuir model. The oxidation was more efficient for ARB adsorbed on magnetite than in solution. The adsorption capacity of magnetite increased significantly after regeneration, which was the result of an increase in surface area of the adsorbent and change of elemental ratio (oxygen:iron [O:Fe]) on the surface. The maximum adsorption capacity for ARB was 32.4 mg/g adsorbent.     

Removal of insoluble heavy metal sulfides from water

The necessity of heavy metal removal from wastewater has led to increasing interest in absorbents. We have developed a new approach to obtain high metal adsorption capacity by precipitating metal sulfides with sodium sulfide on the surface of bentonite and adhere them to the absorbent. This method allowed to remove approximately 90% of cadmium as CdS from 10(-4)-10(-6) M CdCl2 solutions. Additional reactions are related to the removal of excess sodium sulfide by the release of hydrogen sulfide and oxidation to sulfur using carbogen gas (5% CO2, 95% O2) followed by aeration.     

Adsorption and desorption of cadmium by goethite pretreated with phosphate

The adsorption of Cd by oxides or soils have been extensively studied, however, the desorption has received relatively limited attention, especially in the presence of phosphate. In this study, a batch equilibration method was used to investigate Cd sorption and desorption by goethite pretreated with phosphate. Phosphate not only enhanced Cd adsorption, but also accelerated the adsorption process. Compared with Cd adsorption by goethite alone, phosphate substantially moved the adsorption curves (edges) to lower pH range, indicative of enhancement of Cd sorption. The Cd adsorption by the pretreated goethite reached apparent equilibrium within 24 h at 20 degrees C, while such equilibrium was not observed after 4 weeks in the absence of phosphate. Cadmium was more readily released from phosphate-treated goethite. It is believed that phosphate blocked the pores on goethite surface, which lead to the fast adsorption kinetics and high extraction percentage. These results provided strong support for the diffusion of Cd into goethite particles.     

Effectiveness and mechanisms of hydrogen sulfide adsorption by camphor-derived biochar

The characteristics and mechanisms of hydrogen sulfide (H₂S) adsorption on a biochar through pyrolysis at various temperatures (100 to 500°C) were investigated. The biochar used in the current study was derived from the camphor tree (Cinnamomum camphora). The samples were ground and sieved to produce particle sizes of 0.4 mm to 1.25 mm, 0.3 mm to 0.4 mm, and <0.3 mm. The H₂S breakthrough capacity was measured using a laboratory-designed test. The surface properties of the biochar were characterized using pH and Fourier-transform infrared spectroscopy (FTIR) analysis. The results obtained demonstrate that all camphor-derived biochars were effective in H₂S sorption. Certain threshold ranges of the pyrolysis temperature and surface pH were observed, which, when exceeded, have dramatic effects on the H₂S adsorption capacity. The sorption capacity ranged from 1.2 mg/g to 121.4 mg/g. The biochar with 0.3 mm to 0.4 mm particle size possesses a maximum sorption capacity at 400°C. The pH and FTIR analysis results showed that carboxylic and hydroxide radical groups were responsible for H₂S sorption. These observations will be helpful in designing biochar as engineered sorbents for the removal of H₂S.

Implications: This paper studies the potential of biochar derived by camphor to adsorb hydrogen sulfide at environmentally sustainable temperatures. The different sizes of the biochars and the different temperatures of pyrolysis for the camphor particle have a great impact on adsorption of hydrogen sulfide.     

钢渣吸附处理苯酚废水的研究

采用恒温振荡的方法,考察了钢渣粒径、吸附温度、振荡速度、溶液pH值、溶液初始浓度对苯酚去除率的影响。结果表明,在粒径为120~180目、pH=4.0、苯酚溶液浓度在500 mg/L以内、苯酚/钢渣质量比为1∶1 000时吸附效果最好。钢渣对苯酚的吸附能较好地符合Langmuir和Freundlich吸附等温线,线性相关系数分别为0.9971和0.9916,吸附机理为表面吸附。     

污泥活性炭对次甲基蓝废水的吸附

立足于污泥的资源化,利用化学活化法制得的污泥基活性炭,处理次甲基蓝染料废水.考察了污泥活性炭的粒径以及染料废水的pH值对染料脱色效果以及活性炭的吸附量的影响,并对吸附过程进行等温吸附线和吸附动力学分析.结果表明,在本研究的范围内,污泥活性炭的粒径越小、染料废水的pH值越高,则污泥活性炭对染料废水的吸附效果越好.当粒径在200目以上时,去除率及吸附量分别为88.2％和136.7 mg/g;当pH值为11时,去除率和吸附量分别为90.4％和91.9 mg/g.污泥活性炭对次甲基蓝染料的吸附脱除符合Langmuir吸附等温线和Lagergren准二级动力学方程.     

Physicochemical characteristics of carbonaceous adsorbent for dioxin-like polychlorinated biphenyl adsorption

It has been known that dioxin-like polychlorinated biphenyls (DL-PCBs) are present in almost all types of environments worldwide. Activated carbon treatment has been expected for the removal of DL-PCBs because it is a simple and low-cost removal technology. In the present study, the physicochemical properties of activated carbon were investigated to identify the characteristics of 16 different types of activated carbon on adsorption properties for DL-PCBs. To accomplish this, micropore volume, and pore diameter were calculated by t-plot analysis and the mesopore volume was analyzed by the Barrett-Joyner-Halenda (BJH) method. In addition, the Brunauer-Emmett-Teller (BET) surface area, pH, metal elements, and surface acid functional groups were analyzed. Then, adsorption experiments using DL-PCB in hexane solution were conducted, and the relationship between adsorption and physicochemical properties of activated carbon was investigated. The results showed that activated carbons having a surface area of 700-1200 m² g⁻¹ and micropores with diameters of about 0.7-0.8 nm exhibited high activity for the adsorption of PCBs. The results also clearly showed that the mesopore volume of activated carbon influenced the adsorption rate and the equilibrium adsorption.     

Kinetics and stoichiometry of aerobic sulfide oxidation in wastewater from sewers-effects of pH and temperature.

Kinetics and stoichiometry of aerobic chemical and biological sulfide oxidation in wastewater from sewer networks were studied. In this respect, the effects of temperature and pH were investigated in the ranges 10 to 20 degrees C and 5 to 9, respectively. The temperature dependency of sulfide oxidation kinetics was described using an Arrhenius relationship. The effect of pH on the rate of chemical sulfide oxidation is related to the dissociation of hydrogen sulfide (H2S) to hydrogen sulfide ion (HS(-)), with HS(-) being more readily oxidized than H2S. Biological sulfide oxidation exhibited the highest rates at ambient wastewater pH, and the reaction was inhibited at both low and high pH values. Chemical sulfide oxidation was found to produce thiosulfate and sulfate, while elemental sulfur was the main product of biological sulfide oxidation. Based on the investigations, general rate equations and stoichiometric constants were determined, enabling the processes to be incorporated to conceptual sewer process models.     

Recovery of hydrogen and removal of nitrate from water by electrocoagulation process

The present study provides an optimization of electrocoagulation process for the recovery of hydrogen and removal of nitrate from water. In doing so, the thermodynamic, adsorption isotherm, and kinetic studies were also carried out. Aluminum alloy of size 2 dm² was used as anode and as cathode. To optimize the maximum removal efficiency, different parameters like effect of initial concentration, effect of temperature, pH, and effect of current density were studied. The results show that a significant amount of hydrogen can be generated by this process during the removal of nitrate from water. The energy yield calculated from the hydrogen generated is 3.3778 kWh/m³. The results also showed that the maximum removal efficiency of 95.9 % was achieved at a current density of 0.25 A/dm², at a pH of 7.0. The adsorption process followed second-order kinetics model. The adsorption of NO ₃ ^? preferably fitting the Langmuir adsorption isotherm suggests monolayer coverage of adsorbed molecules. Thermodynamic studies showed that adsorption was exothermic and spontaneous in nature. The energy yield of generated hydrogen was ~54 % of the electrical energy demand of the electrocoagulation process. With the reduction of the net energy demand, electrocoagulation may become a useful technology to treat water associated with power production. The aluminum hydroxide generated in the cell removes the nitrate present in the water and reduced it to a permissible level making the water drinkable.     

沼液中臭味物质的去除方法及其对营养物质的影响

采用臭氧曝气法、粉末活性炭吸附法、颗粒活性炭过滤法、臭氧曝气-粉末活性炭吸附联用法、空气曝气-粉末活性炭吸附联用法对沼液中的氨气、硫化氢、吲哚、挥发酚类等主要致嗅物质的去除情况进行了研究,同时分析了不同方法对沼液中营养物质TN、DN、TP、DP等的影响。结果表明,采用粉末活性炭吸附法处理沼液,臭味物质的去除情况以及营养物质的保留效果最好,当粉末活性炭投加量为15 000 mg/L时,沼液中的硫化氢、吲哚、挥发酚已经完全去除,氨氮、氨气的去除率分别为11.42%、13.98%;DN、DP含量分别减少了10.46%、19.53%,但是TN、TP含量分别增加了6.26%、9.63%。