Iron-mediated reactions of polychlorinated biphenyls in electrochemical peroxidation process (ECP)

A study was conducted to explore some of the basic processes of polychlorinated biphenyl (PCB) destruction by a new technology termed electrochemical peroxidation process (ECP). ECP represents an enhancement of the classic Fenton reaction (H2O2 + Fe2+) in which iron is electrochemically generated by steel electrodes. Focus was on the extent of adsorption of a mixture of Aroclor 1248 on steel electrodes in comparison to iron filings. Commercially available zero-valent iron filings rapidly adsorbed PCBs from an aqueous solution of Aroclor 1248. Within 4 h, all the PCBs were adsorbed at 1%, 5%, and 10% Fe0 (w/v) concentrations. Little difference in adsorption was found between acidic (2.3) and unamended solutions (pH 5.5), even though significant differences in iron oxidation state and Fe2+ concentrations were measured in solution. PCB adsorption also occurs on steel electrodes regardless of the pH or electric current applied (AC or DC), suggesting the combination of oxidizing (free radical-mediated reactions) and reducing (dechlorination reactions) iron-mediated degradation pathways may be possible. Extraction of the iron powder after 48 h of contact time yielded the progressive recovery of biphenyl with increasing Fe mass(from 0.4% to 3.5%) and changes of the PCB congener-specific pattern as a consequence of dechlorination. A variety of daughter congeners similar to those accumulated during anaerobic microbial dechlorination of Aroclor 1248 in contaminated sediments indicate preferential removal of meta- and para-chlorines.     

超声波和零价铁联用对氯代苯酚脱氯降解作用的研究

采用超声波和零价铁联用对氯代有机物3氯苯酚(CP)、2,4-二氯苯酚(DCP)和2,4,6-三氯苯酚(TCP)模拟废水进行了脱氯处理研究。以单因素法, 考察了铁粉初始投加量、溶液的初始浓度、超声波功率和溶液的pH值等因素对氯代酚降解的影响,并探讨了降解反应动力学。结果表明,超声波和零价铁联用对氯酚具有显著的降解效果,当水样初始浓度为25 mg/L,溶液pH呈弱酸性,超声波功率为200 W时,氯代酚的脱氯效率达到最大值。降解反应符合准一级反应,CP、DCP和TCP的反应速率常数分别0.0613 h^-1、0.374 h^-1和0.197 h^-1。     

Efficient dehalogenation of automobile shredder residue in NaOH/ethylene glycol using a ball mill

We investigated the effectiveness of sodium hydroxide/ethylene glycol (NaOH/EG) for dehalogenation of automobile shredder residue (ASR) using a ball mill. Efficient dehalogenation was achieved at atmospheric pressure by combining the use of EG (196 degrees C b.p.) as a replacement solvent for NaOH with ball milling, which improved contact between ASR and OH(-) in solution. Moderate NaOH concentrations and increased ball mill rotation speeds produced high dechlorination that was not significantly affected by the weight ratio of ASR to EG. NaOH/EG dechlorination increased with temperature with an apparent activation energy of 50 kJ mol(-1) confirming that the reaction proceeded under chemical reaction control. The modified shrinking-core model was appropriate to explain the dechlorination process. Low chloro levels in our NaOH/EG-treated ASR suggested that this material could be used for feedstock recycling and the wet process may be applicable for dehalogenation of other important waste streams.     

Enhanced reductive dechlorination of polychlorinated biphenyl-contaminated soil by in-vessel anaerobic composting with zero-valent iron

Anaerobic dechlorination is an effective degradation pathway for higher chlorinated polychlorinated biphenyls (PCBs). The enhanced reductive dechlorination of PCB-contaminated soil by anaerobic composting with zero-valent iron (ZVI) was studied, and preliminary reasons for the enhanced reductive dechlorination with ZVI were investigated. The results show that the addition of nanoscale ZVI can enhance dechlorination during in-vessel anaerobic composting. After 140 days, the average number of removed Cl per biphenyl with 10 mg g^?1 of added nanoscale ZVI was 0.63, enhancing the dechlorination by 34 % and improving the initial dechlorination speed. The ZVI enhances dechlorination by providing a suitable acid base environment, reducing volatile fatty acid inhibition and stimulating the microorganisms. The C/N ratios for treatments with the highest rate of ZVI addition were smaller than for the control, indicating that ZVI addition can promote compost maturity.     

Using solar and ultraviolet light to degrade PCBs in sand and transformer oils

The present study describes the effect of the operating variables in the sensitized solar photolysis of sandy sediments contaminated by polychlorinated biphenyls (PCBs) in alkaline isopropanol. PCBs were almost completely removed in two weeks with stoichiometric release of chloride and biphenyl (BP) by a mechanism of reductive dechlorination. The concentration of the sensitizer (acetone) was the variable found to have most influence on the process. Under the same conditions, only partial dechlorination of the PCBs (34%) was observed in dielectric fluids without generating biphenyl to any appreciable extent. Direct photolysis (ultraviolet light at 254nm) of dielectric oils dissolved in alkaline isopropanol lead to 92% removal of PCBs in 60min. The observed mechanism was again that of reductive dechlorination, with stoichiometric release of chloride, and the accumulation of biphenyl, quaterphenyl and condensation products of biphenyl with isopropanol.     

Dechlorination of hexachlorobiphenyl by using potassium-sodium alloy

2,2',4,4',5,5'-Hexachlorobiphenyl (HCB) was dechlorinated with potassium-sodium (K-Na) alloy under an inert gas atmosphere. Solvent effect was observed in the reaction. Dechlorination yields in benzene and cyclohexane were 99.9998%, and 99.99996%, respectively. The reaction was exothermic and proceeded at room temperature. In benzene, trace amounts of polychlorinated biphenyls (PCBs) as products by stepwise dechlorination and polychlorinated quarterphenyls as product of Wurtz-Fittig reaction were detected as reaction intermediate. Reaction products were biphenyl, cyclohexylbenzene, and dicyclohexyl. In cyclohexane, there were no products of Wurtz-Fittig reaction. Dechlorination at para-position preferred to that at ortho-position, judging from analysis of PCBs as intermediates of stepwise dechlorination.     

Dechlorination of polychlorinated organic compounds by electrochemical reduction with naphthalene radical anion as mediator

Electrochemical reduction with electrochemically generated naphthalene radical anion in N,N-dimethylformamide was applied to the dechlorination of five representative POPs, namely HCB, lindane, DDT, PCP and aldrin. Rapid and complete dechlorination was possible for lindane and DDT to give nearly quantitative yields of benzene and 1,1-diphenylethane, respectively. HCB was reduced through complex reaction pathways to yield unknown products. Dechlorination of PCP and aldrin beyond dichlorinated compounds was difficult because of their very negative reduction potential. The reaction pathways for each dechlorination were proposed with the identification of intermediates.     

Catalytic dechlorination of monochlorobenzene with a new type of nanoscale Ni(B)/Fe(B) bimetallic catalytic reductant

A unique type of nanoscale Ni(B)/Fe(B) bimetallic catalytic reductant was prepared and used for dechlorination of monochlorobenzene (MCB). The sample Ni(B)/Fe(B) was synthesized by an electroless plating method, in which nanoscale Ni(B) was deposited on the surface of nanoscale Fe(B) synthesized by chemical reduction. The results suggest that the nanoscale Ni(B)/Fe(B) bimetallic catalytic reductant has higher dechlorination efficiency than Ni/Fe(B) catalytic reductant prepared by replacing Fe(B) with Ni(2+) in aqueous solution. The Ni content was found to be an important factor in catalytic dechlorination, with the dechlorination rate increasing with Ni content. The electroless plating method improve the efficiency of the Ni(2+) in the solution. Dechlorination takes place with the existence of nanoscale Ni(B)/Fe(B) bimetallic catalytic reductant via a pseudo-first-order reaction.     

Electron transfer sensitized photodechlorination of surfactant solubilized PCB 138

Sensitized photodechlorination of polychlorinated biphenyl, PCB 138, in three different surfactant solutions was studied. The sensitizer of choice was leuco-methylene blue, which was produced in situ from methylene blue using either triethylamine or sodium borohydride. Three types of surfactants, anionic (SDS), neutral (TWEEN 80), and cationic (CTAB) at different concentrations were investigated. The neutral and cationic surfactants were found to be more effective than anionic. In each case the surfactant concentration was found to play a significant role in the rate of dechlorination. For different sensitized systems (triethylamine or sodium borohydride), a different product distribution and a different pathway of dechlorination was observed.     

Effect of groundwater geochemistry on pentachlorophenol remediation by smectite-templated nanosized Pd0/Fe0

Zero-valent iron holds great promise in treating groundwater, and its reactivity and efficacy depend on many surrounding factors. In the present work, the effects of solution chemistry such as pH, humic acid (HA), and inorganic ions on pentachlorophenol (PCP) dechlorination by smectite-templated Pd(0)/Fe(0) were systematically studied. Smectite-templated Pd(0)/Fe(0) was prepared by saturating the negatively charged sites of smectite clay with Fe(III) and a small amount of Pd(II), followed by borohydride reduction to convert Fe(III) and Pd(II) into zero-valent metal clusters. Batch experiments were conducted to investigate the effects of water chemistry on PCP remediation. The PCP dechlorination rate critically depends on the reaction pH over the range 6.0~10.0; the rate constant (k (obs)) increases with decreasing the reaction pH value. Also, the PCP remediation is inhibited by HA, which can be attributed to the electron competition of HA with H(+). In addition, the reduction of PCP can be accelerated by various anions, following the order: Cl(-) > HCO (3) (-) > SO (4) (2-) ~no anion. In the case of cations, Ca(2+) and Mg(2+) (10 mM) decrease the dechlorination rate to 0.7959 and 0.7798 from 1.315 h(-1), respectively. After introducing HA into the reaction systems with cations or/and anions, the dechlorination rates are similar to that containing HA alone. This study reveals that low pH and the presence of some anions such as Cl(-) facilitate the PCP dechlorination and induce the rapid consumption of nanosized zero-valent iron simultaneously. However, the dechlorination rate is no longer correlated to the inhibitory or accelerating effects by cations and anions in the presence of 10 mg/L HA.     

Dechlorination of hexachlorobenzene using lead–iron bimetallic particles

Synthesized lead–iron (Pb/Fe) bimetallic particles were applied to dechlorinate hexachlorobenzene (HCB) under various conditions (e.g. bimetal amount, initial pH value, reaction temperature, and reaction duration). The results showed that adding Pb onto Fe benefited the dechlorination of HCB and the bimetal with 1.4% Pb content performed best. The degradation rate decreased regularly as the initial pH value of the aqueous increased from 1.9 to 11.1 except for pH 7.0 where the fastest dechlorination rate emerged. The dechlorination could be enhanced by increasing the amount of Pb/Fe or the reaction temperature. The dechlorination ratio of HCB within 15 min increased from 24.3% to 81.3% when Pb/Fe amount increased from 0.1 g to 0.8 g. The dechlorination followed pseudo-first-order kinetics, and the dechlorination rate constants were 0.0027, 0.0064, 0.0157, and 0.0321 min^?1 at 25, 50, 70, and 85 °C, respectively, and the activation energy (E_a) of the dechlorination by Pb/Fe was 37.86 kJ mol^?1.     

Catalyzed dehalogenation of Delor 103 by sodium hydridoaluminate

The complete dechlorination of PCB liquid Delor 103 (42.6% Cl) to biphenyl has been effected in toluene with sodium dihydridobis(2-methoxyethoxo)aluminate (SDMA) in the presence of catalytic amounts of Ni(II) and Co(II) 2,4-pentanedionates at elevated temperatures. Changes in PCB congeners distribution during dechlorination were monitored by GC(ECD) and GC/MS, and the scheme of their transformation was proposed on the basis of site selectivity observed. A kinetic analysis of the reaction is presented.     

Dechlorination pathways of ortho-substituted PCBs by UV irradiation in n-hexane and their correlation to the charge distribution on carbon atom

The photodegradations of 22 individual polychlorinated biphenyl (PCB) congeners (including 21 non-coplanar ortho substituted and one non-ortho substituted) by irradiation with ultraviolet lamp in n-hexane solution were studied. Photoproducts were identified by matching their retention times and mass spectra with those of authentic standards. PCB congener with less than two chlorides was photodegraded within half an hour, if more than three chlorine on ring, the photodechlorination time for PCB needs one and half hours or more, sometimes even longer than 15 h. The half-life of PCB degradation by photodechlorination was much shorter than that by anaerobic biological dechlorination. Charge distribution on carbon atom combined with the monitoring products of individual PCB congeners were used to deduce the photodegradation pathways. The higher the charge distribution for carbon to which chlorine is attached, the easier for photodechlorination to occur. A lot of chlorine atoms attached PCB, the dechlorination was found to occur prior to the carbon with higher charge distribution at the benzene ring with more chlorine atoms attached.     

Structure relationship for catalytic dechlorination rate of dichlorobenzenes in water

Three isomers of dichlorobenzene (o-, m- and p-DCB) were dechlorinated by Pd/Fe catalyst in aqueous solutions through catalytic reduction. The dechlorination reaction took place on the surface site of the catalyst via a pseudo-first-order kinetics, and resulted in benzene as the final reduction product. The rate constants of the reductive dechlorination for the three dichlorobenzenes (DCBs) in the presence of Pd/Fe as a catalyst were measured experimentally. In all cases, the reaction rate constants were found to increase with the decrease in the Gibbs free energy of the formation of DCBs. The reaction rate constant for o-, m- and p-DCBs in the presence of 0.020% (w/w) Pd/Fe at 25 °C was determined to be 0.0213, 0.0223, and 0.0254 min⁻¹, respectively. While the activation energy of each dechlorination reaction was measured to be 102.5, 96.6 and 80.0 kJ mol⁻¹ for o-, m- and p-DCBs, respectively. The results demonstrated that p-DCBs were reduced more easily than o- or m-DCBs, and the order of the tendency of the dechlorination was p-DCB > m-DCB > o-DCB. The presented data show the catalytic reduction using Pd/Fe as a catalyst is a fast and easy approach for the dechlorination of DCBs.     

钯/铝双金属体系对3-氯酚的脱氯降解

研究了钯/铝双金属体系对水相中3-氯酚的催化脱氯降解效果,通过置换沉积制备了钯/铝双金属颗粒,考察了该双金属颗粒的稳定性以及溶液pH和钯负载量对脱氯效果的影响。结果表明,pH在4.0以下的酸性条件,钯负载量在1.43%时,可实现水相中3-氯酚的有效脱氯,反应30 min后0.389 mmol/L的3-氯酚转化率可达99%以上,产物主要为苯酚,而钯/铝颗粒在重复测试中能保持较好的稳定性,这与铝基材表面自发形成的氧化膜有关。钯/铝材料表征的结果表明,钯颗粒高度分散在铝基材表面,并极大地提高了铝基材的表面积,从而有助于后续的脱氯反应。     

Reductive dechlorination and biodegradation of 2,4,6-trichlorophenol using sequential permeable reactive barriers: laboratory studies

The reductive dechlorination and biodegradation of 2,4,6-trichlorophenol (2,4,6-TCP) was investigated in a laboratory-scale sequential barrier system consisting of a chemical and biological reactive barrier. Palladium coated iron (Pd/Fe) was used as a reactive barrier medium for the chemical degradation of 2,4,6-TCP, and a sand column seeded with anaerobic microbes was used as a biobarrier following the chemical reactive barrier in this study. Only phenol was detected in the effluent from the Pd/Fe column reactor, indicating that the complete dechlorination of 2,4,6-TCP was achieved. The residence time of 30.2-21.2h was required for the complete dechlorination of 2,4,6-TCP of 100 mg l(-1) in the column reactor. The surface area-normalized rate constant (k(SA)) is 3.84 (+/-0.48)x10(-5)lm(-2)h(-1). The reaction rate in the column tests was one order of magnitude slower than that in the batch test. In the operation of the biobarrier, about 100 microM of phenol was completely removed with a residence time of 7-8d. Consequently, the dechlorination prior to biodegradation turns out to increase the overall treatability. Moreover, the sequential permeable reactive barriers, consisting of iron barrier and biobarrier, could be recommended for groundwater contaminated with toxic organic compounds such as chlorophenols.     

高锰酸钾降解地下水中PCE的研究

以氯代有机污染物中常见的PCE为目标污染物,以自制高锰酸钾溶液为氧化剂,采用批实验方法,探讨了高锰酸钾降解PCE的反应动力学、影响因素以及反应机理。反应结果表明,高锰酸钾降解PCE的反应符合一级动力学方程,反应活化能E为57.119 kJ/mol,在30℃条件下,反应速率常数为0.0076 min^-1,半衰期为91.20 min。在pH在3～10,离子强度在0～0.1030 mol/L之间变化时,反应速率不受明显影响。     

The reactive transport of trichloroethene is influenced by residence time and microbial numbers

The dechlorination rate in a flow-through porous matrix can be described by the species specific dechlorination rate observed in a liquid batch unless mass transport limitations prevail. This hypothesis was examined by comparing dechlorination rates in liquid batch with that in column experiments at various flow rates (3-9-12 cm day(-1)). Columns were loaded with an inoculated sand and eluted with a medium containing 1mM trichloroethene (TCE) for 247 days. Dechlorination in the column treatments increased with decreasing flow rate, illustrating the effect of the longer residence time. Zeroth order TCE or cis-DCE degradation rates were 4-7 folds larger in columns than in corresponding batch systems which could be explained by the higher measured Geobacter and Dehalococcoides numbers per unit pore volume in the columns. The microbial numbers also explained the variability in dechlorination rate among flow rate treatments marked by a large elution of the dechlorinating species' yield as flow increased. Stop flow events did not reveal mass transport limitations for dechlorination. We conclude that flow rate effects on reactive transport of TCE in this coarse sand are explained by residence time and by microbial transport and that mass transport limitations in this porous matrix are limited.     

Biodegradation of coplanar polychlorinated biphenyls by anaerobic microorganisms from estuarine sediments.

In this study, we investigated the biodegradability of biphenyl and 5 congeners (one non-planar and four coplanar) of polychlorinated biphenyl (PCB). Biphenyl, the non-planar congener 2,3',4',5-tetrachlorobiphenyl (25-34 CB), and the four coplanar congeners 3,3',4,4'-tetrachlorobiphenyl (34-34 CB), 3,4,4',5-tetrachlorobiphenyl (345-4 CB), 3,3',4,4',5-pentachlorobiphenyl (345-34 CB), and 3,3',4,4',5,5'-hexachlorobiphenyl (345-345 CB) were amended at a concentration of 10 mg/L into anoxic sediment slurries collected from the estuaries of the Tansui River and the Erjen River. During 2 years' incubation under sulfidogenic conditions, biphenyl was persistent, while all other chlorinated congeners, except for 345-345 CB, were dechlorinated with or without a lag period in sediment slurries collected from both rivers. Dechlorination of coplanar and non-planar congeners began with para chlorine removal. All para chlorines from the mono-, di-, and trichlorobiphenyl groups could be removed by sediment slurries from both rivers. Microbial communities in sediment from the Erjen River additionally fostered meta-dechlorination activity, but only after removal of all the para chlorines. Addition of Tween 20 (0.05%, v/v) into sediment slurries from the Tansui River did not enhance dechlorination rates or extents, but the addition of toluene- or 3-chlorobenzoate-adapted sediments enhanced dechlorination of 34-34 CB and 345-4 CB.