Survival of selected pathogens in diluted sludge of a thermophilic waste treatment plant and in NaCl-solution under aerobic and anaerobic conditions

Decimal reduction times (DRT or D-value) of Campylobacter jejuni, Salmonella enterica (formerly Salmonella choleraesuis) serovar Senftenberg, Escherichia coli, and Listeria monocytogenes were determined in two different matrices, diluted fermenter sludge (DFS) and 0.95% NaCl-solution (NaCl) at 50 degrees C, both under aerobic and anaerobic conditions. Depending on aeration, matrix composition, and the respective organism, the D-values varied between 10min and more than 15h. Generally the viability of bacteria decreased faster in DFS compared to NaCl-solution and under aerobic compared to anaerobic conditions. After 24h no viable cells could be detected in DFS, both under aerobic as well as under anaerobic conditions, whereas viable cells were still found in NaCl solutions. In both matrices the detection limits determined by means of PCR-based and classical microbiological methods were compared and pointed to lower detection limits of the latter methods. Results of the present investigation show that test organisms were far from surviving several days in DFS whereas hydraulic retention times normally used for thermophilic anaerobic digestion are in the range of 2 weeks. However, an underestimation of survival rates of the test organisms seems probable when applying aerobic standard methods.     

Evaluation of the effects of PFAS soil adsorption and transformation in the presence of divalent cations under ambient conditions

A bench‐scale study was conducted to evaluate the effect of divalent cations on the adsorption of perfluoroalkyl and polyfluoroalkyl substances (PFAS) onto soil particles. The study entailed batch testing of a synthetic soil mixture under a range of Epsom salt (soluble magnesium sulfate heptahydrate) concentrations. The synthetic soil was produced using a mix of sand, silt, clay, and organic matter that then was mixed and saturated with water collected from a PFAS‐impacted water source. The results indicate that variable concentrations of magnesium (divalent cation) had a minor effect on the sorption of perfluorooctane sulfonate with the highest sorption occurring in the strongest solution of Epsom salt. An unanticipated result of the test involved apparent biomediated transformation of polyfluorinated alkylated sulfonates (fluorotelomers or FTS) to perfluorooctanoic acid, perfluoroheptanoic acid (PFHpA), and perfluorononanoic acid. We believe this is the first time the complete transformation of 6:2 FTS to PFHpA has been observed and reported under ambient surface water‐like conditions within 6 months, a relatively short timeframe.     

Paper fibers as a carbon source for the de novo formation of polychlorinated dioxins and furans

The formation of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/Fs) from carbon that was produced by the pyrolysis of paper fibers and from wood charcoal was investigated experimentally. Fibers obtained from filter paper were pyrolyzed at 300° and 800°C to produce low- and high-temperature carbon samples. The two types of carbon and wood charcoal were mixed with silica (SiO₂) and trace copper oxide to produce three synthetic fly ash samples. Experiments to measure the formation of PCCDs/Fs from the three ash samples were conducted using a bench-scale reactor. The two carbon samples derived from paper fibers generated more PCDDs/Fs than was generated by the wood charcoal. The PCDDs/Fs generated by the low-temperature carbon and by the wood charcoal were dominated by the lower-chlorinated PCDFs. Such unique homologue distribution patterns are very similar to those generated by the open burning of household waste. The high-temperature carbon generated more highly chlorinated PCDDs/Fs. The effect of pyrolysis temperature on the de novo formation of PCDDs/Fs from residual carbon is discussed. Paper and paper products contained in household waste are likely to be the source of unburned carbon that contributes to high PCDD/F emissions in the open burning of household waste.     

Synthesis,Characterization, and Potential Evaluation of Modified Cellulose Immobilized with Hydroxyquinoline as a Sorbent for Vanadium Ions

Journal of Polymers and the Environment - A considerable increase in the importance of vanadium globally and its common uses in many manufacturable alloys made it a target for much scientific...     

Composting of a solid olive-mill by-product ("alperujo") and the potential of the resulting compost for cultivating pepper under commercial conditions

A pollutant solid material called "alperujo" (AL), which is the main by-product from the Spanish olive oil industry, was composted with a cotton waste as bulking agent, and the compost obtained (ALC) was compared with a cattle manure (CM) and a sewage sludge compost (SSC) for use as organic amendment on a calcareous soil. The experiment was conducted with a commercial pepper crop in a greenhouse using fertigation. Composting AL involved a relatively low level of organic matter biodegradation, an increase in pH and clear decreases in the C/N and the fat, water-soluble organic carbon and phenol contents. The resulting compost, which was rich in organic matter and free of phytotoxicity, had a high potassium and organic nitrogen content but was low in phosphorus and micronutrients. The marketable yields of pepper obtained with all three organic amendments were similar, thus confirming the composting performance of the raw AL. When CM and SSC were used for soil amendment, the soil organic matter content was significantly reduced after cultivation, while it remained almost unchanged in the ALC-amended plots.     

GHG emission factors developed for the collection,transport and landfilling of municipal waste in South African municipalities

Greenhouse gas (GHG) emission factors are used with increased frequency for the accounting and reporting of GHG from waste management. However, these factors have been calculated for developed countries of the Northern Hemisphere and are lacking for developing countries. This paper shows how such factors have been developed for the collection, transport and landfilling of municipal waste in South Africa. As such it presents a model on how international results and methodology can be adapted and used to calculate country-specific GHG emission factors from waste. For the collection and transport of municipal waste in South Africa, the average diesel consumption is around 5 dm³ (litres) per tonne of wet waste and the associated GHG emissions are about 15 kg CO₂ equivalents (CO₂ e). Depending on the type of landfill, the GHG emissions from the landfilling of waste have been calculated to range from ?145 to 1016 kg CO₂ e per tonne of wet waste, when taking into account carbon storage, and from 441 to 2532 kg CO₂ e per tonne of wet waste, when carbon storage is left out. The highest emission factor per unit of wet waste is for landfill sites without landfill gas collection and these are the dominant waste disposal facilities in South Africa. However, cash strapped municipalities in Africa and the developing world will not be able to significantly upgrade these sites and reduce their GHG burdens if there is no equivalent replacement of the Clean Development Mechanism (CDM) resulting from the Kyoto agreement. Other low cost avenues need to be investigated to suit local conditions, in particular landfill covers which enhance methane oxidation.     

Evaluation of the available air pollution control technologies for achievement of the MACT requirements in the newly implemented new source performance standards (NSPS) and emission guidelines (EG) for hospital and medical/infectious waste incinerators

After many years of research and debate, in August of 1997 the United States Environmental Protection Agency (EPA) issued New Source Performance Standards (NSPS) and Emission Guidelines (EG) for medical/infectious waste incinerators in the United States. These new emissions and operational standards establish considerably more restrictive limitations on air emissions for medical/infectious waste incinerators and will undoubtedly have a significant impact on the over 2300 hospitals presently operating an incinerator on-site. This paper will explore the options available to these facilities, and those facilities which may be considering installation of an incinerator, relative to achieving compliance with the NSPS and EG for medical/infectious waste incinerators.     

The Application of Stable Isotopes for Assessing the Hydrological, Sulfur, and Iron Balances of Acidic Mining Lake ML 111 (Lusatia, Germany) as a Basis for Biotechnological Remediation

Stable isotope (¹⁸O–H₂O, ²H–H₂O ³⁴S–SO₄ ^2-) andhydrochemical data (SO₄ ^2-, Fe-concentrations) have beenused to estimate the annual groundwater inflow and outflow of mining lake ML 111 and to calculate the total amount of dissolvedsulfate and iron that is carried into the lake by groundwater. The hydrological balance suggests an annual groundwater inflow of 23 700 m³ and an annual groundwater outflow of 15 700 m³. The calculation of the sulfur and iron balances yielded an annual sulfate input of 37 800 kg and an annual iron input of 7000 kg with the groundwater inflow. Furthermore it was shown that significant fluxes of these elements go into the lake sediments which results in continuous release of acidity in the lake water.     

Lessons learned for a more efficient knowledge and technology transfer to South American countries in the fields of solid waste and contaminated sites management.

The present paper describes the development, performance and conclusions derived from three know-how and technology transfer projects to South American countries. The first project comprised a collaborative study by European and South American universities to find sustainable solutions for Chilean and Ecuadorian leather tanneries which had underachieving process performances. The second project consisted of investigations carried out in a Brazilian municipality to enhance its municipal solid waste management system. The final collaborative programme dealt with the initial identification, evaluation and registration of suspected contaminated sites in an industrial region of Chile. The detailed objectives, methods and procedures applied as well as the results and conclusions obtained in each of the three mentioned projects are presented, giving special attention to the organizational aspects and to the practical approach of each programme, concluding with their main advantages and disadvantages for identifying a set of qualitative and quantitative suggestions, and to establish transferable methods for future applications.     

Evaluation of a lime-mediated sewage sludge stabilisation process. Product characterisation and technological validation for its use in the cement industry

This paper describes an industrial process for stabilising sewage sludge (SS) with lime and evaluates the viability of the stabilised product, denominated Neutral, as a raw material for the cement industry. Lime not only stabilised the sludge, raised the temperature of the mix to 80-100 °C, furthering water evaporation, portlandite formation and the partial oxidation of the organic matter present in the sludge.Process mass and energy balances were determined. Neutral, a white powder consisting of portlandite (49.8%), calcite (16.6%), inorganic oxides (13.4%) and organic matter and moisture (20.2%), proved to be technologically apt for inclusion as a component in cement raw mixes. In this study, it was used instead of limestone in raw mixes clinkerised at 1400, 1450 and 1500 °C. These raw meals exhibited greater reactivity at high temperatures than the limestone product and their calcination at 1500 °C yielded clinker containing over 75% calcium silicates, the key phases in Portland clinker. Finally, the two types of raw meal (Neutral and limestone) were observed to exhibit similar mineralogy and crystal size and distribution.     

Waste to energy: a decision-making process for technology selection through characterization of waste,considering energy and emission in the city of Ahmedabad,India

Journal of Material Cycles and Waste Management - Municipal solid waste (MSW) disposal has become major issue for the city of Ahmedabad, India. Development, concentrated population and economic...     

Description and identification of difficulties arising from the application of a cleaning process in operating conditions for the treatment of components used on liquid metal fast reactors (LMFR). A technical designed approach to avoid these situations

The cleaning process is one of the major maintenance operation for liquid metal fast reactors (LMFRs), both in operation and in their decommissioning stage. Russian and French cleaning processes are briefly described, including problems which have arisen during the processes. It appears that the cause of these problems is always connected to bad draining of the component, resulting in a vigorous reaction between vapour or liquid water and the bulk of sodium. From this discussion, the paper makes major recommendations for the efficient and safe cleaning of sodium wetted components, and proposes several processes which should be developed in order to deal with difficult situations, for example the removal of large amounts of undrainable sodium.     

Development of a model for the evaluation of compost supply–demand dynamics: theory and case study in an area of Rabat region,Morocco

Journal of Material Cycles and Waste Management - Compost Supply–Demand (CSD) dynamics is one of the important aspects to consider when assessing composting plants’ sustainability....