Fate and Transport of Fuel Components Below Slightly Leaking Underground Storage Tanks

Fuel leaks from underground storage tanks (USTs) and piping have been a major source of groundwater contamination. In the U.S. and Europe, regulations requiring upgrading of USTs to meet specific standards have significantly reduced instances of fuel contamination. Leak detection is primarily dependent on physical measurement systems that are generally capable of detecting leak rates as small as 0.2 L/h. Fuel leaks that are smaller than this detection threshold may remain undetected for long periods of time, posing a risk of contamination to shallow groundwater resources in sensitive areas. This risk was evaluated by modeling fate and transport of fuel components from small UST leaks under a variety of subsurface conditions and assuming that secondary containment does not exist. It was found that small leaks do have the potential to impact shallow groundwater, particularly if subsurface conditions are not conducive to natural attenuation processes. This may explain situations where groundwater contamination has been found below service stations in virgin areas that have upgraded leak detection systems. Modeling indicates that passive venting of tank and piping backfill could virtually eliminate the volatile components of fuel resulting from small leaks. Monitoring the tank and piping backfill for persistent gasoline vapor under very low vapor extraction conditions may be the best way to detect small chronic fuel leaks. Routine monitoring of shallow groundwater should be a component of a leak detection program, particularly in high-risk areas.     

Handling of dioxin measurement data in the presence of non-detectable values: overview of available methods and their application in the Seveso chloracne study

Exposure measurements of concentrations that are non-detectable or near the detection limit (DL) are common in environmental research. Proper statistical treatment of non-detects is critical to avoid bias and unnecessary loss of information. In the present work, we present an overview of possible statistical strategies for handling non-detectable values, including deletion, simple substitution, distributional methods, and distribution-based imputation. Simple substitution methods (e.g., substituting 0, DL/2, DL/ radical2, or DL for the non-detects) are the most commonly applied, even though the EPA Guidance for Data Quality Assessment discouraged their use when the percentage of non-detects is >15%. Distribution-based multiple imputation methods, also known as robust or "fill-in" procedures, may produce dependable results even when 50-70% of the observations are non-detects and can be performed using commonly available statistical software. Any statistical analysis can be conducted on the imputed datasets. Results properly reflect the presence of non-detectable values and produce valid statistical inference. We describe the use of distribution-based multiple imputation in a recent investigation conducted on subjects from the Seveso population exposed to 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD), in which 55.6% of plasma TCDD measurements were non-detects. We suggest that distribution-based multiple imputation be the preferred method to analyze environmental data when substantial proportions of observations are non-detects.     

A new method for testing the sensitivity of active biomonitoring: an example of its application to a terrestrial moss

For the first time, the concepts of limit of detection and limit of quantification, commonly used in analytical chemistry, are applied to the field of active biomonitoring with terrestrial mosses, using the controls as blanks so that the limits indicate the error associated with the transplant technique. The application of these concepts to data corresponding to Hg concentrations in the surroundings of a chlor-alkali plant and a power plant, makes interpretation of the results easier by providing better spatial and temporal coherence. This procedure may allow improvement in the standardization of active biomonitoring techniques as it is applicable to all kinds of biomonitors. One disadvantage of the application of the limit of detection and limit of quantification is that they only take into account the alpha error, or risk of false positives, and do not take into account the beta error, or risk of false negatives.     

Biodegradation of disodium cocoamphodiacetate by a wastewater microbial consortium.

Biodegradation of an amphoteric surfactant commonly used in personal care products, disodium cocoamphodiacetate (DSCADA), was evaluated. Results from respirometry experiments indicated that high levels of DSCADA (>216 mg/L) may be toxic to bacteria in wastewater treatment processes. Limited biodegradation, with 50% dissolved organic carbon (DOC) removal and 80% chemical oxygen demand removal was observed in batch assays, while complete removal of the parent compound, DSCADA, was noted. Oxygen biosensors were used to evaluate biodegradability of the metabolites present in the batch samples. Additional aerobic microbial activity was not detected in these samples, even with a residual DOC of approximately 45 mg/L. Results from this research indicate that biodegradability of DSCADA is limited and recalcitrant metabolites may be formed. Because DSCADA is a commonly used surfactant and is present in domestic and industrial wastewater, the associated risk posed by residual compounds should be carefully evaluated.     

Trace elements in major solid-pesticides used in the Gaza Strip

This study describes the purity of pesticides used in Gaza in terms of trace elements. A semi-quantitative EMMA-XRF technique and quantitative ICP/OES was used to determine the concentrations of Al, As, Ba, Br, Ca, Cd, Co, Cr, Cu, Fe, K, Mn, Ni, Pb, Rb, Sc, Se, Sr, Ti and Zn in 50 of the most commonly used solid pesticides collected from the five central shops in the Gaza Strip. The results revealed that the pesticides contain considerable amounts of trace elements and do not comply with the expected-theoretical structure of each species. Moreover, they do not reflect the actual constituents mentioned in the trade labels. Interviews with market owners and field surveys confirmed that the pesticides were not pure. In some cases they have been mixed in local markets with minor inorganic species without a scientific basis. They may also have been smuggled into Gaza with differing impurities. The results indicate that pesticides should be considered as a source of certain trace metals (particularly Cu, Mn and Zn) and other elements (Br, Sr and Ti), which may affect their mass balances in soil and groundwater as well as their plant uptake. Different scenarios and calculation models of the transport of trace elements in soil and groundwater of the Gaza Strip should include pesticides as an additional source.     

Sludge age, stability, and safety factor for the biofilm-activated sludge process reactor

The average sludge age (theta(c)) of the activated sludge process (ASP)-biofilm were developed and verified experimentally. In addition, the stability and safety factor were investigated against theta(c). through a series of curves. These curves are important to explain, in concept, the function of the hybrid system under different values of theta(c). The proposed curves of this study are simple and can be modified for any specified wastewater. The definition of theta(c) of ASP was found to be applicable to the hybrid system after including the biofilm. A ratio ranging from 70 to 80% of the total mass of biofilm may be used in the definition of theta(c). to give close results with the experimental values. Furthermore, the minimum sludge age (theta(c)(M)) does not exist in the hybrid reactor because of the presence of biofilm; however, theta(c) should come down to a critical value under some specific conditions of the reactor.     

Maximizing Legacy and Impact of Primary Research: A Call for Better Reporting of Results

Much of the scientific literature in existence today is based on model systems and case studies, which help to split research into manageable blocks. The impact of this research can be greatly increased in meta-analyses that combine individual studies published over time to identify patterns across studies; patterns that may go undetected by smaller studies and that may not be the main subject of investigation. However, many potentially useful studies fail to provide sufficient data (typically means, true sample sizes, and measures of variability) to permit meta-analysis. Authors of primary research studies should provide these summary statistics as a minimum, and editors should require them to do so. By putting policies in place that require these summary statistics to be included, or even those that require raw data, editors and authors can maximize the legacy and impact of the research they publish beyond that of their initial target audience.     

Mass spectrometry up to 1 million mass units for the simultaneous detection of primary soot and of soot precursors (nanoparticles) in flames

A hybrid setup consisting of low pressure burner, flow reactor and photo-ionization mass spectrometer was used for the simultaneous detection of primary soot and of flame generated nanoparticles precursing soot. The studied flames were low pressure (120-180 mbar) C2H4/O2 flames surrounded by an N2 shield. The flow reactor was not used in this study. Through variation of the burner conditions (stoichiometry, sampling height) it could be shown that nanoparticles and soot are entirely independent species. The former, in particular, are found very early in the flame and their concentration profiles do not vary very much throughout the flame. This renders the possibility that nanoparticles are emitted together with soot and consequently may constitute an additional environmental hazard. Photo-ionization mass spectrometry is well suited for the detection of these particles.     

Sorption kinetics and its effects on retention and leaching.

Sorption of pesticides to substrates used in biopurification systems is important as it controls the system's efficiency. Ideally, pesticide sorption should occur fast so that leaching of the pesticide in the biopurification system is minimized. Although modeling of pesticide transport commonly assumes equilibrium, this may not always be true in practice. Sorption kinetics have to be taken into account. This study investigated the batch sorption kinetics of linuron, isoproturon, metalaxyl, isoxaben and lenacil on substrates commonly used in a biopurification system, i.e. cow manure, straw, willow chopping, sandy loam soil, coconut chips, garden waste compost and peat mix. The first-order sorption kinetics model was fitted to the observed pesticide concentrations versus time resulting in an estimated kinetic rate constant alpha. Sorption appeared to be fast for the pesticides linuron and isoxaben, pesticides which were classified as immobile, while less mobile pesticides displayed an overall slower sorption. However, the substrate does not seem to be the main parameter influencing the sorption kinetics. Coconut chips, which is a substrate with a high organic matter content showed slow sorption for most of the pesticides. The effect of different estimated alpha values on the breakthrough of pesticides through a biopurification system was evaluated using the HYDRUS 1D model. Significant differences in leaching behavior were observed as a result of the obtained differences in sorption kinetics.     

Air Quality Standards for the Protection of Farm Animals from Fluorides

The ingestion of forages contaminated with inorganic fluorides from industrial sources constitutes an air pollution problem for domestic livestock. In cattle, which have been studied most extensively, the syndrome is characterized by dental and skeletal lesions, lameness, chemical evidence of increased fluoride ingestion, and in severe cases by effects on appetite and milk production. The only practical basis for a standard appears to be one based on forage fluoride concentrations. It is concluded that a standard should protect cattle from loss of milk production and from severe dental fluorosis, but need not be set so low that the animals will be protected against any discernible deviations from normal which do not influence their general health, productive ability, or the soundness and wearing quality of their dentition. As there may be wide seasonal variations in forage fluoride concentrations, the basic standard should be expressed as a yearly average of the forage fluoride concentration. However, as the developing teeth may be adversely influenced by short periods of high exposure, the standard should contain a provision which limits both the extent and duration of time that high concentrations may be tolerated even though they are balanced by lower values at other months. Based on these criteria, a tentative standard which limits forage fluoride to an average of 40 ppm, and limits the time that forage concentrations may exceed 60 or 80 ppm F is proposed.     

Uncertainties in the role of land vegetation in the carbon cycle

Since the late 1950s the CO2 concentration of the atmosphere has been increasing by around 0.5-3 ppm per year. Understanding of carbon sinks is vital to understanding this trend and its future behaviour. Here we examine some of the factors which may affect the proportion of anthropogenic CO2 ending up in the atmosphere in the present and in the future, and variability in the CO2 increase from one year to another. We also examine the evidence for the potential of terrestrial ecosystem carbon sinks to take up or release CO2. In some cases, a careful re-examination of the research methods used to deduce present and future feedbacks may be necessary. The most advanced technology and the most complex models do not necessarily produce reliable results. They should be carefully checked against a general background knowledge of ecological processes before their results are accepted.     

Evaluation of approaches for terrestrial hazard classification

Hazard assessment is an essential element in the evaluation of the potential effects of chemical substances on the environment. To date, most work has focused on hazard assessment schemes for the aquatic environment, but in recent years, a number of proposals have been developed for other environmental compartments. Due to limited datasets, the suitability of the toxicity cut-off values in these schemes has not been fully determined and the practicalities associated with using these approaches have not been fully established. This study, which focused on the soil compartment, was performed to examine cut-off values proposed by two terrestrial hazard assessment schemes and establish the availability of data. Data on earthworms indicated that current proposals for toxicity cut-off values are appropriate. However, analysis of IUCLID (International Uniform ChemicaL Information Database) indicates that even for commonly used high production volume chemicals, insufficient data are available to enable classification. Whilst the necessary data may already be available for selected groups of substances (e.g. pesticides and veterinary medicines), a significant experimental testing programme would therefore be required before a terrestrial classification system could be applied widely. Such data may become available in the future as a result of initiatives such as REACH.     

DNA damage effect of cyprodinil and thiacloprid in adult zebrafish gills

Cyprodinil and thiacloprid are two of the most commonly used pesticides in Turkey. It is more likely to reach humans or animals due to their widespread use. This study aims to investigate whether there is a DNA damage risk due to cyprodinil and thiacloprid exposure. Zebrafish, which is used as a model organism in health and environmental research, and comet assay were chosen to demonstrate this damage. Ten zebrafish per group were exposed to 2 different concentrations for each pesticides (0.31 and 0.155 mg/L for cyprodinil and 1.64 and 0.82 mg/L for thiacloprid) for 21 days. After, gills were excised and comet assay was performed. Photos of an average of 50 cells per slide were taken and were analyzed with visual evaluation program. DNA damage was found to be increased in the 0.31 mg/L cyprodinil, 0.82 mg/L thiacloprid, and 1.64 mg/L thiacloprid treatment groups when compared to the control group (p < 0.001). Average tail DNA percentage parameter values were 9.45 ± 0.51, 10.30 ± 0.34, 11.17 ± 0.33, and 2.47 ± 0.06 respectively. Cyprodinil and thiacloprid were identified as genotoxic agents that should be investigated further.

     

Quantification of emission factor uncertainty

Emissions factors are important for estimating and characterizing emissions from sources of air pollution. There is no quantitative indication of uncertainty for these emission factors, most factors do not have an adequate data set to compute uncertainty, and it is very difficult to locate the data for those that do. The objectives are to compare the current emission factors of Electric Generating Unit NOx sources with currently available continuous emission monitoring data, develop quantitative uncertainty indicators for the Environmental Protection Agency (EPA) data quality rated emission factors, and determine the possible ranges of uncertainty associated with EPA's data quality rating of emission factors. EPA's data letter rating represents a general indication of the robustness of the emission factor and is assigned based on the estimated reliability of the tests used to develop the factor and on the quantity and representativeness of the data. Different sources and pollutants that have the same robustness in the measured emission factor and in the representativeness of the measured values are assumed to have a similar quantifiable uncertainty. For the purposes of comparison, we assume that the emission factor estimates from source categories with the same letter rating have enough robustness and consistency that we can quantify the uncertainty of these common emission factors based on the qualitative indication of data quality which is known for almost all factors. The results showed that EPA's current emission factor values for NOx emissions from combustion sources were found to be reasonably representative for some sources; however AP-42 values should be updated for over half of the sources to reflect current data. The quantified uncertainty ranges were found to be 25-62% for A rated emission factors, 45-75% for B rated emission factors, 60-82% for C rated emission factors, and 69-86% for D rated emission factors, and 82-92% for E rated emission factors.     

Preparation of gasification feedstock from leafy biomass

Dried leaves are a potential source of energy although these are not commonly used beside to satisfy daily energy demands in rural areas. This paper aims at preparing a leafy biomass feedstock in the form of briquettes which can be directly used for combustion or to extract the combustible gas using a gasifier. Teak (Tectona grandis) and rubber (Hevea brasiliensis) leaves are considered for the present study. A binder-assisted briquetting technique with tapioca starch as binder is adopted. Properties of these leafy biomass briquettes such as moisture content, calorific value, compressive strength, and shatter index are determined. From the study, briquettes with biomass-to-binder ratio of 3:5 are found to be stable. Higher mass percentage of binder is considered for preparation of briquettes due to the fact that leafy biomasses do not adhere well on densification with lower binder content. Ultimate analysis test is conducted to analyze the gasification potential of the briquettes. Results show that the leafy biomass prepared from teak and rubber leaves has calorific values of 17.5 and 17.8 MJ/kg, respectively, which are comparable with those of existing biomass feedstock made of sawdust, rice husk, and rice straw.     

Formation and emission of chloroanisoles as indoor pollutants

GOAL, SCOPE AND BACKGROUND: Complaints by residents of frame-houses about musty odour in the houses has become an increasing problem within the last years. An additional problem is that the odour is transferred to clothes and skin. The persons themselves do not recognize the smell after a while because of adaptation. Serious social problems are the result. For a long time, the smell was explained to be from mould due to construction-based humidity problems. However, in an increasing number of houses, no indications were found for elevated levels of mould growth. METHODS: Air and material samples were taken from 5 houses, which show typical musty odours, and analysed with respect to chlorophenols and chloroanisoles. Additionally, some samples were analysed for lindane and its metabolites, because lindane was commonly used together with pentachlorophenol (PCP) for wood protection. RESULTS AND DISCUSSION: Meticulous analysis resulted in the identification of chloroanisoles, mainly 2,3,4,6-tetrachloroanisole. These substances are known from corky wines and from contamination of food from pentachlorophenol (PCP) treated pallets and result from microbiological metabolic processes. Pentachlorophenol was commonly used to protect wood from fungi in Germany mainly in the later 60s and 70s. Details of these processes, as well as effective methods to identify chloroanisoles in the problem houses, are described. CONCLUSIONS: Chloroanisoles formed by metabolism of PCP have been well known to contaminate food or wine. Here, they were identified and are probably responsible for the musty odours in the frame houses. Since it is quite clear that these substances were not components of building materials used in the houses, an explanation for chloroanisole formation is proposed. Localized dampness probably favours microbial growth associated with metabolic conversion of chlorophenols to the corresponding chloroanisoles, primarily 2,3,4,6-tetrachloroanisol, which spread throughout the buildings, resulting in the observed odours. RECOMMENDATIONS AND OUTLOOK: The group of chloroanisoles has been recognized as important indoor pollutants as they possess musty odours at extremely low concentrations, e.g. for 2,4,6-trichloroanisole in a range of 5-10 ppt in air (Staples 2000). On the basis of currently available toxicological data, exposure of the occupants to the concentrations of chloroanisoles measured is not associated with a health risk. No correlation could be observed between concentrations of chloroanisoles and PCP in house dust and indoor air. However, chloroanisoles are good indicators for possible PCP-treatment of wood in frame houses and their detection should initiate investigations on PCP contamination. Research is continuing to identify the microorganisms involved and to devise a remediation procedure for affected houses.     

Current status of agricultural and rural non-point source Pollution assessment in China

Estimates of non-point source (NPS) contribution to total water pollution in China range up to 81% for nitrogen and to 93% for phosphorus. We believe these values are too high, reflecting (a) misuse of estimation techniques that were developed in America under very different conditions and (b) lack of specificity on what is included as NPS. We compare primary methods used for NPS estimation in China with their use in America. Two observations are especially notable: empirical research is limited and does not provide an adequate basis for calibrating models nor for deriving export coefficients; the Chinese agricultural situation is so different than that of the United States that empirical data produced in America, as a basis for applying estimation techniques to rural NPS in China, often do not apply. We propose a set of national research and policy initiatives for future NPS research in China.     

Effects of wastewater disinfection on waterborne bacteria and viruses.

Wastewater disinfection is practiced with the goal of reducing risks of human exposure to pathogenic microorganisms. In most circumstances, the efficacy of a wastewater disinfection process is regulated and monitored based on measurements of the responses of indicator bacteria. However, inactivation of indicator bacteria does not guarantee an acceptable degree of inactivation among other waterborne microorganisms (e.g., microbial pathogens). Undisinfected effluent samples from several municipal wastewater treatment facilities were collected for analysis. Facilities were selected to provide a broad spectrum of effluent quality, particularly as related to nitrogenous compounds. Samples were subjected to bench-scale chlorination and dechlorination and UV irradiation under conditions that allowed compliance with relevant discharge regulations and such that disinfectant exposures could be accurately quantified. Disinfected samples were subjected to a battery of assays to assess the immediate and long-term effects of wastewater disinfection on waterborne bacteria and viruses. In general, (viable) bacterial populations showed an immediate decline as a result of disinfectant exposure; however, incubation of disinfected samples under conditions that were designed to mimic the conditions in a receiving stream resulted in substantial recovery of the total bacterial community. The bacterial groups that are commonly used as indicators do not provide an accurate representation of the response of the bacterial community to disinfectant exposure and subsequent recovery in the environment. UV irradiation and chlorination/dechlorination both accomplished measurable inactivation of indigenous phage; however, the extent of inactivation was fairly modest under the conditions of disinfection used in this study. UV irradiation was consistently more effective as a virucide than chlorination/dechlorination under the conditions of application, based on measurements of virus (phage) diversity and concentration. Taken together, and when considered in conjunction with previously published research, the results of these experiments illustrate several important limitations of common disinfection processes as applied in the treatment of municipal wastewaters. In general, it is not clear that conventional disinfection processes, as commonly implemented, are effective for control of the risks of disease transmission, particularly those associated with viral pathogens. Microbial quality in receiving streams may not be substantially improved by the application of these disinfection processes; under some circumstances, an argument can be made that disinfection may actually yield a decrease in effluent and receiving water quality. Decisions regarding the need for effluent disinfection must account for site-specific characteristics, but it is not clear that disinfection of municipal wastewater effluents is necessary or beneficial for all facilities. When direct human contact or ingestion of municipal wastewater effluents is likely, disinfection may be necessary. Under these circumstances, UV irradiation appears to be superior to chlorination in terms of microbial quality and chemistry and toxicology. This advantage is particularly evident in effluents that contain appreciable quantities of ammonia-nitrogen or organic nitrogen.     

Primary biodegradability of mineral base oils in relation to their chemical and physical characteristics.

The primary biodegradability of 32 mineral base (i.e., unformulated) oils of paraffinic nature was evaluated using the CEC L-33-A-93 test. These oils were refinery products obtained by varying manufacturing processes. Biodegradation percentages ranged between 15% and 75%, i.e., below the commonly accepted standards for environmentally-compatible lubricants. Biodegradability values were compared to the overall chemical composition and main physical properties of base oils. Biodegradability decreased with increasing levels of aromatic and/or polar compounds in the tested oils. For most oils, the biodegradation percentage increased with the viscosity index, but was a decreasing function of the kinematic viscosity (KV), the pour point, the flash point (FP) and the refractive index (RI). Linear relationships between biodegradability and FP or RI values were observed. These results show that, beside chemical features such as the contents in polar and aromatic compounds, simple physical magnitudes such as KV and RI, commonly used to characterize lubricant properties, may be useful parameters for predicting the biodegradability of mineral base oils.     

Review of passive accumulation devices for monitoring organic micropollutants in the aquatic environment

Over the past 15 years passive sampling devices have been developed that accumulate organic micropollutants and allow detection at ambient sub ng/l concentrations. Most passive accumulation devices (PADs) are designed for 1-4 weeks field deployment, where uptake is governed by linear first order kinetics providing a time weighted average of the exposure concentration. Semipermeable membrane devices (SPMDs) are the most comprehensively studied PADs, but other samplers may also be considered for aquatic monitoring purposes. The applicability of the PADs is reviewed with respect to commonly monitored aqueous matrices and compounds, the detection limits, and for use in quantitative monitoring related to requirements embedded in the EU Water Framework Directive, the US and EU Water Quality Criteria, and the Danish monitoring aquatic programme. The PADs may monitor >75% of the organic micropollutants of the programmes. Research is warranted regarding the uptake in PADs in low flow environments and for the development of samplers for polar organic compounds.