In situ bioelectrokinetic remediation of phenol-contaminated soil by use of an electrode matrix and a rotational operation mode

In situ bioremediation is a safe and cost-effective technology for the cleanup of contaminated sites, but its remediation rate is usually very slow. This study attempted to accelerate the process of bioremediation by employing non-uniform electrokinetic transport processes to mix organic pollutants and degrading bacteria in soils under in situ conditions (namely, in situ bioelectrokinetic remediation) by use of an electrode matrix and a rotational operation mode. A bench-scale non-uniform electrokinetic system with periodic polarity-reversal was developed for this purpose, and tested by using a sandy loam spiked with phenol as a model organic pollutant. The results demonstrated that non-uniform electrokinetic processes could enhance the in situ biodegradation of phenol in the soil, the efficiency of which depended upon the operational mode of the electric field. Compared with the unidirectional operation and the bidirectional operation, the rotational operation could effectively stimulate the biodegradation of phenol in the soil if adopting appropriate time intervals of polarity-reversal and electrode matrixes. A reversal interval of 3.0 h and a square-shaped electrode matrix with four electrode couples appeared appropriate for the in situ biodegradation of phenol, at which a maximum phenol removal of 58% was achieved in 10d and the bioremediation rate was increased about five times as compared to that with no electric field applied. The results also showed that adopting a small polarity-reversal interval and an appropriate electrode array could produce a high and uniform removal of phenol from the soil. It is believed that in situ bioelectrokinetic remediation holds the potential for field application.     

Effect of expandable clays and cometabolism on PAH biodegradability

Pyrene and phenanthrene degradation was examined in both single and binary slurry systems for three different natural soils. It was found that the amount of total expandable clays (smectite and vermiculite) was in a good agreement with the achieved rate and extent of biodegradation. For instance, the intrinsic phenanthrene biodegradation rate was 626 microg/L/day for the soil with the largest expandable clay and 3203 microg/L/day for the soil with the least. Similarly, the smallest total pyrene biodegradation (65%) was found for the soil rich in expandable clays, compared to an 82% pyrene reduction in the soil that had the lowest amount. Mass transfer limitation after compound sorption to the clays was more pronounced for the more hydrophobic pyrene. In the presence of phenanthrene, total pyrene biodegradation increased by 2 to 7% due to cometabolism, while the total phenanthrene biodegradation was only enhanced by 0.5 to 5% in the binary system. This research demonstrated that expandable clays might govern the substrate availability to microorganisms and microbial accessibility to substrates. Therefore, the contribution of organic matter and expandable clays to sorption, desorption and biodegradation should be taken equally into account in order to better understand complex bioremediation issues.     

The use of ozone in the remediation of polycyclic aromatic hydrocarbon contaminated soil

The potential of using ozone for the removal of phenanthrene from several different soils, both alone and in combination with biodegradation using a microbial inoculant (Pseudomonas alcaligenes PA-10), was examined. The greater the water content of the soil the less effective the ozone treatment, with air-dried soils showing the greatest removal of phenanthrene; while soils with higher levels of clay also reduced the effectiveness of the ozone treatments. However, at least a 50% reduction in phenanthrene levels was achieved in air-dried soil after an ozone treatment of 6 h at 20 ppm, with up to 85% removal of phenanthrene achieved in sandy soils. The biodegradation results indicate that P. alcaligenes PA-10 may be useful as an inoculant for the removal of PAHs from contaminated soils. Under the conditions used in our experiments, however, pre-ozonation did not enhance subsequent biodegradation of phenanthrene in the soils. Similar levels of phenanthrene removal occurred in both non-ozonated and ozonated Cruden Bay soil inoculated with P. alcaligenes PA-10. However, the biodegradation of phenanthrene in ozonated Boyndie soil was much slower. This may be due to the release of toxic products in this soil during ozonation.     

Prediction of complete bioremediation periods for PAH soil pollutants in different physical states by mechanistic models

Mass-transfer models and biodegradation models were developed for three theoretical physical states of polycyclic aromatic hydrocarbons (PAHs) in soil. These mechanistic models were used to calculate the treatment periods necessary for complete removal of the PAH pollutants from the soil under batch conditions. Results indicate that the bioremediation of PAHs in such systems is mainly mass-transfer limited. The potential for bioremediation as a treatment technique for PAH contaminated soils is therefore mainly determined by the mass-transfer dynamics of PAHs. Under mass-transfer limited conditions simplified mathematical models, based on the assumption of a zero dissolved PAH concentrations, can be used to predict the period of time needed for complete bioremediation.     

Immobilization of fungal laccase onto a nonionic surfactant-modified clay material: application to PAH degradation

Nonionic surfactant-modified clay is a useful absorbent material that effectively removes hydrophobic organic compounds from soil/groundwater. We developed a novel material by applying an immobilized fungal laccase onto nonionic surfactant-modified clay. Low-water-solubility polycyclic aromatic hydrocarbons (PAHs) (naphthalene/phenanthrene) were degraded in the presence of this bioactive material. PAH degradation by free laccase was higher than degradation by immobilized laccase when the surfactant concentration was allowed to form micelles. PAH degradation by immobilized laccase on TX-100-modified clay was higher than on Brij35-modified clay. Strong laccase degradation of PAH can be maintained by adding surfactant monomers or micelles. The physical adsorption of nonionic surfactants onto clay plays an important role in PAH degradation by laccase, which can be explained by the structure and molecular interactions of the surfactant with the clay and enzyme. A system where laccase is immobilized onto TX-100-monomer-modified clay is a good candidate bioactive material for in situ PAHs bioremediation.     

Oxidation of polycyclic aromatic hydrocarbons by fungal isolates from an oil contaminated refinery soil

BACKGROUND AND OBJECTIVE: Indigenous soil microorganisms are used for the biodegradation of petroleum hydrocarbons in oily waste residues from the petroleum refining industry. The objective of this investigation was to determine the potential of indigenous strains of fungi in soil contaminated with petroleum hydrocarbons to biodegrade polycyclic aromatic hydrocarbons (PAH). MATERIALS AND METHODS: Twenty one fungal strains were isolated from a soil used for land-farming of oily waste residues from the petrochemical refining industry in Singapore and identified to genus level using laboratory culture and morphological techniques. Isolates were incubated in the presence of 30 mg/L of phenanthrene over a period of 28 days at 30 degrees C. The most effective strain was further evaluated to determine its ability to oxidise a wider range of PAH compounds of various molecular weight i.e acenaphthene, fluorene, fluoranthene, chrysene, benzo(a)pyrene and dibenz(ah)anthracene RESULTS AND DISCUSSION: After 28 days of incubation, 18 of the 21 fungal cultures were capable of oxidising over 50% of the phenanthrene present in culture medium, relative to abiotic controls. Fungal isolate, Penicillium sp. 06, was able to oxidise 89% of the phenanthrene present. This isolate could also oxidise more than 75% of the acenaphthene, fluorene and fluoranthene after 30 days of incubation. However, the oxidation of high molecular weight PAH i.e. chrysene, benzo(a)pyrene and dibenz(ah)anthracene by the Penicillium sp. 06 isolate was limited, where the extent of oxidation was inversely proportional to PAH molecular weight. CONCLUSIONS: Fungal isolate, Penicillium sp. 06, was effective at oxidising a range of PAH in petroleum contaminated soils, but higher molecular weight PAH were more recalcitrant. RECOMMENDATIONS AND OUTLOOK: There is potential for the re-application of this fungal strain to soil for bioremediation purposes.     

Hydroxypropyl-β-cyclodextrin extractability and bioavailability of phenanthrene in humin and humic acid fractions from different soils and sediments

Organic matter (OM) plays a vital role in controlling polycyclic aromatic hydrocarbon (PAH) bioavailability in soils and sediments. In this study, both a hydroxypropyl-β-cyclodextrin (HPCD) extraction test and a biodegradation test were performed to evaluate the bioavailability of phenanthrene in seven different bulk soil/sediment samples and two OM components (humin fractions and humic acid (HA) fractions) separated from these soils/sediments. Results showed that both the extent of HPCD-extractable phenanthrene and the extent of biodegradable phenanthrene in humin fraction were lower than those in the respective HA fraction and source soil/sediment, demonstrating the limited bioavailability of phenanthrene in the humin fraction. For the source soils/sediments and the humin fractions, significant inverse relationships were observed between the sorption capacities for phenanthrene and the amounts of HPCD-extractable or biodegradable phenanthrene (p?<?0.05), suggesting the importance of the sorption capacity in affecting desorption and biodegradation of phenanthrene. Strong linear relationships were observed between the amount of HPCD-extractable phenanthrene and the amount degraded in both the bulk soils/sediments and the humin fractions, with both slopes close to 1. On the other hand, in the case of phenanthrene contained in HA, a poor relationship was observed between the amount of phenanthrene extracted by HPCD and the amount degraded, with the former being much less than the latter. The results revealed the importance of humin fraction in affecting the bioavailability of phenanthrene in the bulk soils/sediments, which would deepen our understanding of the organic matter fractions in affecting desorption and biodegradation of organic pollutants and provide theoretical support for remediation and risk assessment of contaminated soils and sediments.     

Simultaneous removal of organic compounds and heavy metals from soils by electrokinetic remediation with a modified cyclodextrin

Thousands of sites are contaminated with both heavy metals and organic compounds and these sites pose a major threat to public health and the environment. Previous studies have shown that electrokinetic remediation has potential to remove heavy metals and organic compounds when they exist individually in low permeability soils. This paper presents the feasibility of using cyclodextrins in electrokinetic remediation for the simultaneous removal of heavy metals and polycyclic aromatic hydrocarbons (PAHs) from low permeability soils. Kaolin was selected as a model low permeability soil and it was spiked with phenanthrene as well as nickel at concentrations of 500 mg kg-1 each to simulate typical mixed field contamination. Bench-scale electrokinetic experiments were conducted using hydroxypropyl beta-cyclodextrin (HPCD) at low (1%) and high (10%) concentrations and using deionized water in control test. A periodic voltage gradient of 2VDC cm-1 (with 5 d on and 2 d off) was applied to all the tests, and 0.01 M NaOH was added during the experiments to maintain neutral pH conditions at anode. In all tests, nickel migrated as Ni2+ ions towards the cathode and most of it was precipitated as Ni(OH)2 within the soil close to the cathode due to high pH condition generated by electrolysis reaction. The solubility of phenanthrene in the flushing solution and the amount of electroosmotic flow controlled the migration and removal of phenanthrene in all the tests. Even though high flow was generated in tests using deionized water and 1% HPCD, migration and removal of phenanthrene was low due to low solubility of phenanthrene in these solutions. The test with 10% HPCD solution showed higher solubility of phenanthrene which caused it migrate towards the cathode, but further migration and removal was retarded due to reduced electric current and electroosmotic flow. Approximately one pore volume of flushing resulted in approximately 50% removal of phenanthrene from the soil near the anode. Sustained higher electroosmotic flow with higher concentration cyclodextrin and maintaining low soil pH near cathode should be investigated to increase removal efficiency of both phenanthrene and nickel.     

Remediation of PAH contaminated soils: application of a solid-liquid two-phase partitioning bioreactor

The feasibility of a two-step treatment process has been assessed at laboratory scale for the remediation of soil contaminated with a model mixture of polycyclic aromatic hydrocarbons (PAHs) (phenanthrene, pyrene, and fluoranthene). The initial step of the process involved contacting contaminated soil with thermoplastic, polymeric pellets (polyurethane). The ability of three different mobilizing agents (water, surfactant (Biosolve) and isopropyl alcohol) to enhance recovery of PAHs from soil was investigated and the results were compared to the recovery of PAHs from dry soil. The presence of isopropyl alcohol had the greatest impact on PAH recovery with approximately 80% of the original mass of PAHs in the soil being absorbed by the polymer pellets in 48 h. The second stage of the suggested treatment involved regeneration of the PAH loaded polymers via PAH biodegradation, which was carried out in a solid-liquid two-phase partitioning bioreactor. In addition to the PAH containing polymer pellets, the bioreactor contained a microbial consortium that was pre-selected for its ability to degrade the model PAHs and after a 14 d period approximately 78%, 62% and 36% of phenanthrene, pyrene, and fluoranthene, respectively, had been desorbed from the polymer and degraded. The rate of phenanthrene degradation was shown to be limited by mass transfer of phenanthrene from the polymer pellets. In case of pyrene and fluoranthene a combination of mass transfer and biodegradation rate might have been limiting.     

Bioremediation of coal tar PAH in soils using biodiesel

The addition of biodiesel together with nitrate and phosphate to soil containing coal tar, in laboratory and field experiments, resulted in degradation of coal tar polycyclic aromatic hydrocarbons (PAH) that was not apparent when the nutrients alone were added. The addition of motor diesel fuel instead of biodiesel was also tested. Over the 55 days of the field and laboratory experiments, the biodiesel resulted in an increased degradation of naphthalene in the coal tar by 52% and 85%, respectively, and motor diesel resulted in increased depletions of 85% and 96%, respectively. Other PAH containing up to four rings were depleted to lesser extents. The increases in PAH biodegradation by the diesel treatments were ascribed to tar solubilisation and dispersion thereby increasing the PAH bioavailability. The ready biodegradability and low phytotoxicity of biodiesel suggest that it may be suitable as a novel treatment for the bioremediation of coal tar contaminated soils.     

Effect of birch (Betula spp.) and associated rhizoidal bacteria on the degradation of soil polyaromatic hydrocarbons, PAH-induced changes in birch proteome and bacterial community

Two birch clones originating from metal-contaminated sites were exposed for 3 months to soils (sand-peat ratio 1:1 or 4:1) spiked with a mixture of polyaromatic hydrocarbons (PAHs; anthracene, fluoranthene, phenanthrene, pyrene). PAH degradation differed between the two birch clones and also by the soil type. The statistically most significant elimination (p ≤ 0.01), i.e. 88% of total PAHs, was observed in the more sandy soil planted with birch, the clearest positive effect being found with Betula pubescens clone on phenanthrene. PAHs and soil composition had rather small effects on birch protein complement. Three proteins with clonal differences were identified: ferritin-like protein, auxin-induced protein and peroxidase. Differences in planted and non-planted soils were detected in bacterial communities by 16S rRNA T-RFLP, and the overall bacterial community structures were diverse. Even though both represent complex systems, trees and rhizoidal microbes in combination can provide interesting possibilities for bioremediation of PAH-polluted soils.     

Solid-phase bioassays and soil microbial activities to evaluate PAH-spiked soil ecotoxicity after a long-term bioremediation process simulating landfarming

The residual ecotoxicity of long-term bioremediated soils concomitantly spiked with three PAHs at four levels (15, 75, 150, 300 mg Sigma 3 PAHs kg(-1) soil) was evaluated using physico-chemical analyses, solid-phase bioassays and soil microbial activities. The pot-scale bioremediation process consisted of weekly moderate waterings in the presence or absence of sewage sludge compost (SSC) under greenhouse conditions. After 15 months, anthracene and pyrene were almost completely degraded whereas benzo[a]pyrene was still persisting, most apparently in SSC-amended soil treatments. However, no apparent toxic effects of the residual PAHs could be detected. SSC application at 40 t ha(-1) was performed to valorize the biowaste and stimulate PAH biodegradation but caused soil salinization and pH reduction at the end of the bioremediation process. Consequently, SSC-amended soils were characterized by strong phytotoxicity to lettuce and had adverse effects on the ostracod Heterocypris incongruens. Despite the smaller number of culturable bacterial populations in SSC-amended soils, soil enzymatic activities were not affected by the organic amendment and residual PAHs; and the bioremediation efficiency was likely to be more limited by the bioavailability of PAHs rather than by the total number of PAH-degraders.     

Uptake of selected PAHs from contaminated soils by rice seedlings (Oryza sativa) and influence of rhizosphere on PAH distribution

The uptake of selected polycyclic aromatic hydrocarbons (PAHs) by rice (Oryza sativa) seedlings from spiked aged soils was investigated. When applied to soils aged for 4 months, naphthalene, phenanthrene, and pyrene exhibited volatilization loss of 98, 95, and 30%, respectively, with the remaining fraction being fixed by soil organic matter and/or degraded by soil microbes. In general, concentrations of the three PAHs in rice roots were greater than those in the shoots. The concentrations of root associated PHN and PYR increased proportionally with both soil solution and rhizosphere concentrations. PAH concentrations in shoots were largely independent of those in soil solution, rice roots, or rhizosphere soil. The relative contributions of plant uptake and plant-promoted rhizosphere microbial biodegradation to the total mass balance were 0.24 and 14%, respectively, based on PYR concentrations in rhizosphere and non-rhizosphere soils, the biomass of rice roots, and the dry soil weight.     

Combined UV-biological degradation of PAHs

The UV-photolysis of PAHs was tested in silicone oil and tetradecane. In most cases, the degradation of a pollutant provided within a mixture was lower than when provided alone due to competitive effects. With the exception of anthracene, the larger pollutants (4- and 5-rings) were always degraded first, proving that UV-treatment preferentially acts on large PAHs and thereby provides a good complement to microbial degradation. UV-photolysis was also found to be suitable for treatment of soil extract from contaminated soils. The feasibility of UV-biological treatment was demonstrated for the removal of a mixture of phenanthrene and pyrene in silicone oil. UV-irradiation of the silicone oil led to 83% pyrene removal but no phenanthrene photodegradation. Subsequent treatment of the oil in a two-phases partitioning bioreactor (TPPB) system inoculated with Pseudomonas sp. was followed by complete phenanthrene biodegradation but no further pyrene removal. Totally, the combined process allowed 92% removal of the PAH mixture. Further work should focus on characterizing the photoproducts formed and studying the influence of the solvent on the photodegradation process.     

Physicochemical soil parameters affecting sequestration and mycobacterial biodegradation of polycyclic aromatic hydrocarbons in soil

Six soils, obtained from grasslands and wooded areas in Northeastern Illinois, were physicochemically characterized. Measured parameters included total organic carbon (TOC) content, contents of humic acid, fulvic acid and humin, pore volume and pore size distribution, and chemical makeup of soil organic matter (determined using solid-state ¹³C-NMR). Moistened, gamma-sterilized soils were spiked with 200 ppm of either phenanthrene or pyrene (including ¹⁴C label); following 0, 40, or 120 days of aging, the contaminant-spiked soils were then inoculated with Mycobacterium austroafricanum strain GTI-23, and evolution of ¹⁴CO₂ was assessed over a 28-day period. Results for both phenanthrene and pyrene indicated that increased contact time led to increased sequestration and reduced biodegradation, and that TOC content was the most important parameter governing these processes. One soil, although only tested with phenanthrene, showed significantly lower-than-expected sequestration (higher-than-expected mineralization) after 40 days of aging, despite a very high TOC value (>24%). Because the level of sequestration in this soil was proportional to the others after 120 days of aging, this implies some difference in the temporal progression of sequestration in this soil, although not in its final result. The primary distinguishing feature of this soil was its considerably elevated fulvic acid content. Further experiments showed that addition of exogenous fulvic acid to a soil with very low endogenous humic acids/fulvic acids content greatly enhanced pyrene mineralization by M. austroafricanum. Extractabilities of 13 three- to six-ring coal tar PAHs in n-butanol from the six soils after 120 days of sequestration were strongly TOC-dependent; however, there was no discernible correlation between n-butanol extractability and mycobacterial PAH mineralization.     

Removal of organic contaminants from soils by an electrokinetic process: the case of atrazine. Experimental and modeling

The atrazine behaviour in soils when submitted to an electric field was studied and the applicability of the electrokinetic process in atrazine soil remediation was evaluated. Two polluted soils were used, respectively with and without atrazine residues, being the last one spiked. Four electrokinetic experiments were carried out at a laboratory scale. Determination of atrazine residues were performed by enzyme-linked immunosorbent assay (ELISA). The results show that the electrokinetic process is able to remove efficiently atrazine in soil solution, mainly towards the anode compartment: Estimations show that 30-50% of its initial amount is removed from the soil within the first 24h. A one-dimensional model is developed for simulating the electrokinetic treatment of a saturated soil containing atrazine. The movement of atrazine is modelized taking into account the diffusion transport resulting from atrazine concentration gradients and the reversed electro-osmotic flow at acidic soil pH.     

Evaluation of impacts of soil fractions on phenanthrene sorption

Phenanthrene sorption to soils and soil fractions was investigated using two contrasting soils with different clay mineral and organic carbon (OC) contents in an attempt to evaluate the contribution of each soil fraction to phenanthrene sorption and the applicability of the carbon-normalized distribution constant (K(OC)) in soils. Sorbents were characterized using surface analysis, solid-state (13)C NMR analysis, and glass transition temperature (T(g)) analysis to gain a insight into the chemical nature of OC in soils. Dissolved organic carbon (DOC) in the soil solution impeded the phenanthrene sorption, while humins accounted for the predominant phenanthrene sorption in soils. The contribution of OC to phenanthrene sorption in soil would be overestimated if only a K(OC)-approach was adopted, since clay minerals could account for much of the sorption, especially when OC was low in soils. Nitrogen gas was shown to be inappropriate for probing non-polar sorption capacity. The results obtained highlight the importance of clay minerals in governing the sorption of phenanthrene in soil, and emphasize the inapplicability of the carbon-normalized distribution coefficient K(OC) in soils.     

Biodegradability of aged pyrene and phenanthrene in a natural soil

A study was conducted to evaluate the biodegradability of pyrene (PYR) and phenanthrene (PHE) aged in a natural soil. Both the single and binary systems were either biostimulated via a nutrient amendment or bioaugmented via an inoculation of the enriched bacteria and nutrients. Aging resulted in higher concentration of both compounds and smaller bacterial activity in the solution-phase. Surprisingly, the total biodegraded extent was greater in the aged soil system than in the freshly spiked system. As anticipated, biostimulation was not appropriate to attain an effective biodegradation in this study, and bioaugmentation achieved a substantial increase the total biodegradation extent. The above findings were attributed to indigenous Pseudomonas aeruginosa entering a stationary-phase during the 200-day aging and producing rhamnolipid biosurfactants. In addition, a different sampling technique (i.e., after vigorous hand-shaking) revealed a 15 times higher microbial population than the normal sampling from the stagnant solution. Therefore, PAH bioavailability in the aged soils can be underestimated when the microbial activity is determined only from the stagnant solution. Furthermore, cometabolism enhanced PYR degradation when PHE was present as a primary substrate.     

Bioavailability assessment and environmental fate of polycyclic aromatic hydrocarbons in biostimulated creosote-contaminated soil

When hydrocarbon-contaminated soil is subjected to bioremediation technology, hydrocarbon depletion is typically marked by an initially rapid reduction rate. This rate decreases over time and frequently a residual concentration remains in the soil. This kinetic has been attributed primarily to the enrichment of more recalcitrant fractions, as well as to the lack of resting hydrocarbon bioavailability. Thus, at the end of the bioremediation process, a part of the residual hydrocarbon soil concentration represents the non-bioavailable fraction, which is difficult to degrade by microbial populations and which poses a minor hazard. Therefore, determination of the bioavailable fraction in a bioremediation project represents both an estimation of the maximum level of achievable biodegradation, as well as an additional indication of the environmental health hazard. In the present study, aged creosote-contaminated soil was subjected to biostimulation processes, and the bioavailable fraction for several target polycyclic aromatic hydrocarbons (PAHs) was calculated using a mild extraction with cyclodextrines. The amount of PAH extracted corresponded to the desorbing fraction and can be regarded as the bioavailable fraction. The non-desorbing fraction data obtained from this procedure were compared to the remaining PAH concentrations following bioremediation treatment of soil microcosms. These results permitted the establishment of a theoretical biodegradation limit based on the desorbing fraction. In addition, neither accumulation of intermediate metabolites, nor the formation of bound-residues or reduced acute toxicity was observed.     

Anaerobic biodegradation of polycyclic aromatic hydrocarbon in soil

Known concentrations of phenanthrene, pyrene, anthracene, fluorene and acenapthene were added to soil samples to investigate the anaerobic degradation potential of polycyclic aromatic hydrocarbon (PAH). Consortia-treated river sediments taken from known sites of long-term pollution were added as inoculum. Mixtures of soil, consortia, and PAH (individually or combined) were amended with nutrients and batch incubated. High-to-low degradation rates for both soil types were phenanthrene > pyrene > anthracene > fluorene > acenaphthene. Degradation rates were faster in Taida soil than in Guishan soil. Faster individual PAH degradation rates were also observed in cultures containing a mixture of PAH substrates compared to the presence of a single substrate. Optimal incubation conditions were noted as pH 8.0 and 30 degrees C. Degradation was enhanced for PAH by the addition of acetate, lactate, or pyruvate. The addition of municipal sewage or oil refinery sludge to the soil samples stimulated PAH degradation. Biodegradation was also measured under three anaerobic conditions; results show the high-to-low order of biodegradation rates to be sulfate-reducing conditions > methanogenic conditions > nitrate-reducing conditions. The results show that sulfate-reducing bacteria, methanogen, and eubacteria are involved in the PAH degradation; sulfate-reducing bacteria constitute a major component of the PAH-adapted consortia.