A comparative study on the properties,mechanisms and process designs for the adsorption of non-ionic or anionic dyes onto cationic-polymer/bentonite

The adsorption properties and mechanisms of a cationic-polymer/bentonite complex (EPI-DMA/bentonite), prepared from polyepicholorohydrin-dimethylamine and bentonite, for non-ionic dyes (Disperse Blue SBL and Vat Scarlet R) and anionic dyes (Reactive Violet K-3R and Acid Dark Blue 2G) were investigated in this study. The solution pH, presence of salt and surfactant can significantly affect the dye removal efficiency. The equilibrium data were analyzed using the Langmuir and Freundlich models. The Langmuir model is the most suitable to describe non-ionic dye adsorption, but for anionic dyes the Freundlich model is best. The kinetic data for the adsorption of different dyes were analyzed using pseudo first- and second-order equations, and the experimental data conformed to the pseudo second-order kinetic model better. The possibility of intraparticle diffusion was also examined by using the intraparticle diffusion equation. The single-stage batch adsorber design for the adsorption of both types of dyes onto EPI-DMA/bentonite was studied based on the Langmuir isotherm model for non-ionic dyes and the Freundlich isotherm model for anionic dyes. The results showed that the required amount of EPI-DMA/bentonite for 95% dye removal in 5 L dye solution with a concentration of 50 mg/L is 378.0 g for DB SBL, 126.5 g for VS R, 9.7 g for RV K-3R and 15.5 g for ADB 2G.     

茄子秸杆活性炭对染料废水的吸附性能研究

以茄子秸秆为原料,ZnCl2为活化剂制备粉末状活性炭,主要研究了活性炭对染料废水的吸附性能;以活性红X-3B和酸性蓝RL为模型染料,考察了染料初始浓度、pH值、活性炭投加量和吸附时间等对染料脱色率的影响。结果表明,染料初始浓度和活性炭投加量对染料脱色率影响较大。初始浓度为300mg／L时,活性炭的最佳投加量分别为1g／L和1．4g／L;在最佳工艺条件下,脱色率分别在93％和98％以上,COD去除率分别为94．5％和86．4％,出水水质达到国家一级《纺织染整工业水污染物排放标准》（GB 4287—1992）。     

Biosorption of Reactive Black 5 from aqueous solutions by chitosan: Column studies

Fixed-bed column studies were carried out to investigate the dynamic sorption of Reactive Black 5 (RB5) onto chitosan. The effect of operating parameters such as initial dye concentration, superficial flow velocity, bed height and particle size on the sorption of RB5 onto chitosan was studied. Column regeneration, dye recovery and the possibility of reusing the regenerated chitosan were also investigated. The results show that both the breakthrough curves and the adsorption parameters of the column were strongly affected by the operating parameters studied. An analysis of the breakthrough curves indicated that adsorption was affected by mass transfer limitations, probably due to intraparticle diffusion. An empirical model was applied to describe the breakthrough curves, while the Bohart–Adams and BDST models were used to determine the operating parameters useful in the process design. Elution of the column with 0.01 mol L^?1 NaOH allowed the chitosan to be regenerated and the dye to be recovered and concentrated. The concentration factor was 10. Several cycles of adsorption–elution showed that the regenerated chitosan retained good adsorption efficiency and the elution efficiency was always higher than 80%.     

Removal of phenol from aqueous solutions by adsorption

Experiments have been conducted to examine the liquid-phase adsorption of phenol from water by silica gel, HiSiv 3000, activated alumina, activated carbon, Filtrasorb-400, and HiSiv 1000. Experiments were carried out for the analysis of adsorption equilibrium capacities and kinetics. The adsorption isotherm model of the Langmuir-Freundlich type was the best to describe adsorption equilibrium data for phenol for the adsorbents studied. Results of kinetic experiments indicated that HiSiv 1000 had the highest rate of adsorption among the adsorbents studied and therefore more detailed studies were carried out with this adsorbent. The influence of particle size, temperature, and thermal regeneration on adsorption of phenol by HiSiv 1000 was evaluated. From particle size experiments it appeared that adsorption capacity of HiSiv 1000 did not change by changing the particle size, but the rate of adsorption decreased considerably by increasing the particle size. The effect of temperature on adsorption was studied by determining equilibrium isotherms for HiSiv 1000 at 25, 40, and 55 degrees C. The results showed that adsorption capacity decreased with increasing temperature. Thermal regeneration of HiSiv 1000 was performed at 360 degrees C. It was observed that adsorption capacity of HiSiv 1000 did not change after 14 regeneration cycles. Equilibrium experiments showed that the adsorption capacities of activated carbon and Filtrasorb-400 were several times higher than that of HiSiv 1000.     

Application of 'waste' wood-shaving bottom ash for adsorption of azo reactive dye

The utilization of wood-shaving bottom ash (WBA) for the removal of Red Reactive 141 (RR141), an azo reactive dye, was investigated. WBA/H(2)O and WBA/H(2)SO(4) were made by treating WBA with water and 0.1M H(2)SO(4), respectively, to increase adsorption capacity. Adsorption of RR141 from reactive dye solution (RDS) and reactive dye wastewater (RDW) by WBA/H(2)O and WBA/H(2)SO(4) involved the BET surface area and pore size diameter. Properties of adsorbents, effect of contact time, initial pH of solution, dissolved metals and elution studies indicated that the decolorisation mechanism involved both chemical adsorption and precipitation with calcium ions. In addition, the WBA/H(2)SO(4) surface might contain sulphate-cation complexes that were specific to enhancing dye adsorption from RDW. The adsorption isotherm had a best fit by the Freundlich model. Freundlich parameters showed that WBA/H(2)O used more heterogeneous surface than WBA/H(2)SO(4) and activated carbon for RDW adsorption. A thermodynamic study indicated that RDW adsorption was an endothermic process. The maximum dye adsorption capacities of WBA/H(2)O, WBA/H(2)SO(4) and activated carbon obtained from a Langmuir model at 30 degrees C were 24.3, 29.9, and 41.5mgl(-1), respectively. In addition, WBA/H(2)O and WBA/H(2)SO(4) could reduce colour and high chemical oxygen demand (COD) of real textile wastewater. According to the difficulty in the elution study, it was an environmentally safe disposal of this waste. Therefore, WBA, a waste from combustion of wood shavings, was suitable to be used as an effective adsorbent for azo reactive dye removal.     

Use of an activated carbon from antibiotic waste for the removal of Hg(II) from aqueous solution

Porous carbon has been prepared from waste antibiotic material by a chemical activation method using K(2)CO(3) as an activating reagent. Carbon was studied systematically by the adsorption of nitrogen and iodine. It was found that the process parameters such as activation temperature and activation time are crucial for preparing high-quality activated carbon. The proper choice of the preparation conditions allows to produce microporous activated carbon with a micropore volume up to 0.492 cm(3)/g and a BET surface area of 1260 m(2)/g. Adsorption of mercury(II) from an aqueous solution on antibiotic carbon was investigated under the varying conditions of agitation time, metal ion concentration and pH. The adsorption capacity of the carbon is 129 mg/g.     

Removal of mercury from aqueous solutions using activated carbon prepared from agricultural by-product/waste

Removal of mercury from aqueous solutions using activated carbon prepared from Ceiba pentandra hulls, Phaseolus aureus hulls and Cicer arietinum waste was investigated. The influence of various parameters such as effect of pH, contact time, initial metal ion concentration and adsorbent dose for the removal of mercury was studied using a batch process. The experiments demonstrated that the adsorption process corresponds to the pseudo-second-order-kinetic models and the equilibrium adsorption data fit the Freundlich isotherm model well. The prepared adsorbents ACCPH, ACPAH and ACCAW had removal capacities of 25.88 mg/g, 23.66 mg/g and 22.88 mg/g, respectively, at an initial Hg(II) concentration of 40 mg/L. The order of Hg(II) removal capacities of these three adsorbents was ACCPH > ACPAH > ACCAW. The adsorption behavior of the activated carbon is explained on the basis of its chemical nature. The feasibility of regeneration of spent activated carbon adsorbents for recovery of Hg(II) and reuse of the adsorbent was determined using HCl solution.     

Adsorption studies of hazardous malachite green onto treated ginger waste

Adsorption of malachite green (MG) from aqueous solution onto treated ginger waste (TGW) was investigated by batch and column methods. The effect of various factors such as initial dye concentration, contact time, pH and temperature were studied. The maximum adsorption of MG was observed at pH 9. Langmuir and Freundlich isotherms were employed to describe the MG adsorption equilibrium. The monolayer adsorption capacities were found to be 84.03, 163.9 and 188.6 mg/g at 30, 40 and 50 °C, respectively. The values of thermodynamic parameters like ΔG°, ΔH° and ΔS° indicated that adsorption was spontaneous and endothermic in nature. The pseudo second order kinetic model fitted well in correlation to the experimental results. Rechienberg's equation was employed to determine the mechanism of adsorption. The results indicated that film diffusion was a major mode of adsorption. The breakthrough capacities were also investigated.     

WATER RECLAMATION BY PHYSICOCHEMICAL TREATMENT OF WASTEWATER1

ABSTRACT. Treatment of a high strength acidic industrial chemical waste, which had a COD of about 3000 mg/1 and a pH of 3, was attempted by activated carbon adsorption to evaluate the feasibility of yielding effluents of reusable qualities. The experimental methods which were employed in this investigation included batch and column studies. The former was used to evaluate the rate and equilibrium of carbon adsorption while the latter was used to determine treatment efficiencies and performance characteristics. Parallel operations of fixed-bed and expanded-bed adsorbers were contrasted in the column study. Results of this investication indicate that activated carbon was very efficient in removing the COD of the chemical waste. Initial pH adjustments for the wastewater to 7.0 or 11.4 did not increase the COD removal efficiency. Turbidity and nitrogen (total Kjeldahl- and ammonia-N) were removed to some extents by the carbon bed adsorbers while phosphorus (total-and ortho-P) was totally unaffected by the carbon treatment.     

Calcium oxide for CO2 capture: Operational window and efficiency penalty in sorption-enhanced steam methane reforming

Calcium oxide (CaO) is a material that is being widely investigated in the context of CO₂ capture. One such application is as a CO₂ sorbent in the sorption-enhanced steam methane reforming processes (SERP). CO₂ is captured in an adsorption mode, where the conversion of CH₄ to H₂ is also enhanced, and released later in a separate desorption mode. This work presents an analysis of the relation between different process conditions and parameters during both adsorption and desorption modes. The interrelation between these conditions and the sorbent properties as well as the targeted carbon capture ratio is analysed. Conditions relevant for capturing 85% of carbon in the feed on CaO are determined and interlinked. A steam-to-carbon ratio of 4.2 has been determined to be relevant under 600 °C and 17 bar adsorption conditions. Similarly, process conditions relevant for regenerating the sorbent are determined and interlinked. For purge steam-to-CO₂ ratio of 1.8 at a desorption pressure of 1 bar, relevant desorption temperature has been calculated to be 820 °C. System simulations under these adsorption and desorption conditions resulted in a system efficiency of 50.8%. Effect of tuning process operating conditions on system efficiency as well as the efficiency penalty associated with the regeneration of the sorbent are investigated by process simulations using Aspen Plus^®. Possible system heat integration routes to reduce the efficiency penalty are proposed and the results of the process simulations are presented.     

Development of activated carbon from Nerium oleander flower and their rapid adsorption of direct and reactive dyes

The present study investigates the thermally activated carbon derived from Nerium oleander flower which was used an adsorbent. Physicochemical properties of Nerium oleander flower carbon (NOFC) were characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared for the removal of DTB (Direct Turquoise Blue) and RR-HE7B (Reactive red–HE7B) dyes from aqueous solution. Adsorption studies were carried out with different pH, adsorbent dose, contact time, and initial concentration dye solution. Optimum conditions for maximum removal of DTB and RR-HE7B was achieved to be pH 2 for both dyes, adsorbent dose of 100 mg and equilibrium time of 35 and 60 min, respectively, for NOFC. The maximum adsorption capacity of NOFC was found to be 33.33 and 19.60 mg g^?1, respectively, for the removal of dye solution. The mechanism of adsorption was studied by using different kinetic models and isotherms. The results clearly showed that the NOFC adsorption was fitted to pseudo–first-order for DTB and pseudo–second-order for RR-HE7B. Equilibrium data were well fitted with both isotherm models. According to the results, NOFC can effectively remove DTB and RR-HE7B from aqueous solutions.     

LDO处理垃圾渗滤液中氮的实验研究

研究了复合金属氧化物（LDO）用于处理垃圾渗滤液中氮的可行性,并与传统吸附剂粉末活性炭（PAC）进行了比较,考察了投加量、振荡速度、吸附时间、吸附温度、pH等因素对处理效果的影响。结果表明,当垃圾渗滤液中总氮浓度为561mg/L、LDO投加量为6g/L、振荡速度为170r/min、吸附时间为60min、温度为25℃、pH值为11时,LDO对总氮的吸附量最高,达到41mg/g。在相同条件下,LDO对总氮的吸附量是PAC的2.5—3.5倍。     

Desorption kinetics of arsenate from kaolinite as influenced by pH

Arsenic is highly toxic and therefore represents a potential threat to the environment and human health. The mobility and bioavailability of arsenic in soil is mostly controlled by adsorption and desorption reactions. Even though adsorption and traditional batch desorption experiments provide information about the environmental fate of As, the equilibrium conditions imposed in these studies would usually not be reached in the natural environment. Flow-through desorption techniques, where the desorbed species are removed from the substrate, can therefore be used to provide information about the rate and mechanisms of As desorption. The effect of pH on As adsorption reactions is relatively well understood; however, desorption of As and the effect of pH on As desorption remain unexplored. Desorption of As(V) (the most dominant arsenic species in aerated soils) was therefore investigated using batch and flow-through desorption experiments. Traditional batch desorption experiments underestimated the desorption rate of As(V) from kaolinite. The pH had a large effect on the amount of As(V) desorbed from kaolinite, with both an increase and a decrease in pH (from the initial pH 6.4) enhancing As(V) desorption. Modeling desorption over time revealed that the pH can influence As(V) desorption over extended periods of time.     

气相色谱法测定室内空气中挥发性卤代烃

建立了活性炭吸附-溶剂解吸-气相色谱测定室内空气中7种挥发性卤代烃的分析方法。样品经活性炭采样管富集后,用二硫化碳解吸,Agilent HP-1色谱柱分离,使用带有电子捕获检测器的气相色谱仪测定,以保留时间定性,外标法定量。当采样体积为10 L时,方法检出限范围是0.03~0.18 g/m3,加标回收率在72%~114%之间,相对标准偏差小于15%。结果表明,该方法可以应用于室内空气中痕量挥发性卤代烃样品的检测分析。     

Removal of the hazardous dye rhodamine B through photocatalytic and adsorption treatments

This paper reports on photocatalytic and adsorptive treatment of a hazardous xanthene dye, Rohdamine B, in wastewater. The photocatalytic degradation was carried out in the presence of the catalyst TiO(2) and the effects of pH, concentration of the dye, amount of TiO(2), temperature and electron acceptor H(2)O(2) on the degradation process were observed. It was found that photocatalytic degradation by TiO(2) is an effective, economical and faster mode of removing Rohdamine B from aqueous solutions. Attempts were also made to utilize activated carbon and rice husk as potential adsorbents to remove Rhodamine B from wastewater. The adsorption studies were carried out at 40, 50 and 60 degrees C, and the effects of pH, temperature, amount of adsorbents, concentration of adsorbate, etc., on the adsorption were measured. On the basis of adsorption data the Langmuir and Freundlich adsorption isotherm models were also confirmed. The adsorption isotherm constants thus obtained were employed to calculate thermodynamic parameters like Gibb's free energy, change in enthalpy and entropy. In order to observe the quality of wastewater COD measurements were also carried out before and after the treatments. A significant decrease in the COD values was observed, which clearly indicates that both photocatalytic and adsorption methods offer good potential to remove Rhodamine B from industrial effluents.     

活性炭纤维对Cu2＋吸附性能的研究

研究了pH值、吸附接触时间、铜离子的初始浓度及活性炭纤维（ACF）的投加量对活性炭纤维吸附Cu2＋的影响,并选取了最佳的实验条件。用Langmuir方程和Freundlich方程拟合活性炭纤维对Cu2＋吸附等温线,结果表明：活性炭纤维吸附Cu2＋更符合Langmuir等温式,其相关系数为0．9995,以单分子层吸附为主。对活性炭纤维改性能明显提高对Cu2＋的吸附,其中效果最佳的吸附量从4．8mg／g增加到17．32mg／g,提高了3．6倍。     

生物活性炭技术在水处理中的研究进展与应用

总结了生物活性炭（BAC）技术在净水处理、废水处理和污水再生利用处理中的应用;阐述了生物活性炭对污染物的去除机理;介绍了生物活性炭技术在水处理中（包括给水深度处理、多种工业废水及生活污水处理）的最新应用研究成果及该技术的发展方向。     

Application of sludge-based carbonaceous materials in a hybrid water treatment process based on adsorption and catalytic wet air oxidation

This paper describes a preliminary evaluation of the performance of carbonaceous materials prepared from sewage sludges (SBCMs) in a hybrid water treatment process based on adsorption and catalytic wet air oxidation; phenol was used as the model pollutant. Three different sewage sludges were treated by either carbonisation or steam activation, and the physico-chemical properties of the resultant carbonaceous materials (e.g. hardness, BET surface area, ash and elemental content, surface chemistry) were evaluated and compared with a commercial reference activated carbon (PICA F22). The adsorption capacity for phenol of the SBCMs was greater than suggested by their BET surface area, but less than F22; a steam activated, dewatered raw sludge (SA_DRAW) had the greatest adsorption capacity of the SBCMs in the investigated range of concentrations (<0.05 mol L^?1). In batch oxidation tests, the SBCMs demonstrated catalytic behaviour arising from their substrate adsorptivity and metal content. Recycling of SA_DRAW in successive oxidations led to significant structural attrition and a hardened SA_DRAW was evaluated, but found to be unsatisfactory during the oxidation step. In a combined adsorption–oxidation sequence, both the PICA carbon and a selected SBCM showed deterioration in phenol adsorption after oxidative regeneration, but a steady state performance was reached after 2 or 3 cycles.     

Loofa egyptiaca as a novel adsorbent for removal of direct blue dye from aqueous solution

In this paper, Loofa egyptiaca (LE), an agricultural plant cultivated in Egypt, was used to prepare low-cost activated carbon (LE_C1 and LE_C2) adsorbents. The adsorbents (LE, LE_C1 and LE_C2) were evaluated for their ability to remove direct blue 106 dye from aqueous solutions. Batch mode experiments were conducted using various parameters such as pH, contact time, dye concentration and adsorbent concentration. The surface chemistry of LE, LE_C1 and LE_C2 was analyzed by scanning electron microscopy (SEM). The experimental data were examined using Langmuir, Freundlich, Temkin and Harkins–Jura isotherms. The results showed that the adsorption of direct blue 106 was maximal at the lowest value of pH (pH = 2). Removal efficiency was increased with an increase in dye concentration and a decrease in amount of adsorbent. Maximum adsorption capacity was found to be 57.14, 63.3 and 73.53 mg/g for LE, LE_C1 and LE_C2 respectively. Kinetics were also investigated using pseudo-first-order, pseudo-second-order and intra-particle diffusion models. The experimental data fitted very well with the pseudo-first-order and pseudo-second-order kinetic models. The results indicate that LE, LE_C1 and LE_C2 could be employed as adsorbents for the removal of direct blue dye from aqueous solutions.     

Determination of model parameters for zinc (II) ion biosorption onto powdered waste sludge (PWS) in a fed-batch system

Biosorption of zinc (II) ions onto pre-treated powdered waste sludge (PWS) was investigated using a completely mixed tank operating in fed-batch mode instead of an adsorption column. Experiments with variable feed flow rate (0.05-0.5 L h(-1)), feed Zn(II) ion concentrations (37.5-275 mg L(-1)) and amount of adsorbent (1-6 g PWS) were performed using fed-batch operation at pH 5 and room temperature (20-25 degrees C). Break-through curves describing variations of aqueous (effluent) zinc ion concentrations with time were determined for different operating conditions. Percent zinc removal from the aqueous phase decreased, but the biosorbed (solid phase) zinc ion concentration increased with increasing feed flow rate and zinc concentration. A modified Bohart-Adams equation was used to determine the biosorption capacity of PWS (q'(s)) and the rate constant (K) for zinc ion biosorption. Biosorption capacity (q'(s)=57.7 g Zn kg(-1) PWS) of PWS in fed-batch operation was found to be comparable with powdered activated carbon (PAC) in column operations. However, the adsorption rate constant (K=9.17 m(3) kg(-1) h(-1)) in fed-batch operation was an order of magnitude larger than those obtained in adsorption columns because of elimination of mass transfer limitations encountered in the column operations. Therefore, a completely mixed tank operated in fed-batch mode was proven to be more advantageous as compared to adsorption columns due to better contact between the phases yielding faster adsorption rates.