Effect of inoculation in composting processes: modifications in lignocellulosic fraction

Three microbial isolates, identified as Bacillus shackletonni, Streptomyces thermovulgaris and Ureibacillus thermosphaericus were tested as inoculants in composting processes in relation to their capacity to improve lignocellulose degradation. Different wastes from agricultural activities were used as raw material for the heaps: pepper plant waste (PPW) as the main component and olive-oil mill waste (OMW), almond shell (AS), pruning waste (PW) and rice straw (RS) as additives. Cellulose was more extensively degraded than hemicellulose and lignin, although the use of inoculants (B. shackletonni and S. thermovulgaris) improved the action of the autochthonous microbiota just in the AS heaps. A higher efficiency was observed for lignin, since lower concentrations of this polymer were detected in the inoculated heaps in relation to control heaps. U. thermosphaericus was the most efficient microorganism since inoculation with this strain decreased the final lignin content in a range between 17.23% and 24.34%. S. thermovulgaris and B. shackletonni led to a higher reduction of the lignin levels in the OMW and PW heaps (14.25% and 19.07% less lignin than control heaps) and OMW (13%), respectively. The composting process can therefore be improved by means of inoculation if the microorganisms used for this purpose are appropriate for the characteristics of the raw material.     

Effect of water washing on the thermal behavior of rice straw

Rice straw can be used as a renewable fuel for heat and power generation. It is a viable mean of replacing fossil fuels and preventing pollution caused by open burning, especially in the areas where this residual biomass is generated. Nevertheless, the thermal conversion of rice straw can cause some operating problems such as slag formation, which negatively affects thermal conversion systems. So, the main objective of this research is studying the combustion behavior of rice straw samples collected from various regions by applying thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). In addition, the thermal behavior of ashes from rice straw was also analyzed in order to detect their melting points, and ash sintering was detected at different temperatures within the range between 550 and 1000 °C. Since washing rice straw with water could reduce the content of undesirable inorganic compounds related to the ash fusibility, samples of washed rice straw were analyzed under combustion conditions to investigate its differences regarding the thermal behavior of rice straw. The results showed that rice straw washing led to a significant improvement in its thermal behavior, since it reduced the ash contents and sintering formation.     

A comparative study on valuable products: bio-oil,biochar, non-condensable gases from pyrolysis of agricultural residues

Journal of Material Cycles and Waste Management - In this study, pyrolysis of agricultural residues, such as rice straw (RS), wheat straw (WS), and sugarcane bagasse (SB), was performed in a...     

Effects of bulking agent addition on odorous compounds emissions during composting of OFMSW

The effects of rice straw addition level on odorous compounds emissions in a pilot-scale organic fraction of municipal solid waste (OFMSW) composting plant were investigated. The cumulative odorous compounds emissions occurred in a descending order of 40.22, 28.71 and 27.83 mg/dry kg of OFMSW for piles with rice straw addition level at ratio of 1:10, 2:10 and 3:10 (mixing ratio of rice straw to OFMSW on a wet basis), respectively. The mixing ratio of rice straw to OFMSW had a statistically significant effect on the reduction of malodorous sulfur compounds emissions, which had no statistically significant effect on the reduction of VFAs, alcohols, aldehydes, ketones, aromatics and ammonia emissions during composting, respectively. The cumulative emissions of malodorous sulfur compounds from piles with the increasing rice straw addition level were 1.17, 1.08 and 0.88 mg/dry kg of OFMSW, respectively. The optimal mixing ratio of rice straw to OFMSW was 1:5. Using this addition level, the cumulative malodorous sulfur compounds emissions based on the organic matter degradation were the lowest during composting of OFMSW.     

Co-composting of livestock manure with rice straw: Characterization and establishment of maturity evaluation system

Composting is considered to be a primary treatment method for livestock manure and rice straw, and high degree of maturity is a prerequisite for safe land application of the composting products. In this study pilot-scale experiments were carried out to characterize the co-composting process of livestock manure with rice straw, as well as to establish a maturity evaluation index system for the composts obtained. Two pilot composting piles with different feedstocks were conducted for 3 months: (1) swine manure and rice straw (SM–RS); and (2) dairy manure and rice straw (DM–RS). During the composting process, parameters including temperature, moisture, pH, total organic carbon (TOC), organic matter (OM), different forms of nitrogen (total, ammonia and nitrate), and humification index (humic acid and fulvic acid) were monitored in addition to germination index (GI), plant growth index (PGI) and Solvita maturity index. OM loss followed the first-order kinetic model in both piles, and a slightly faster OM mineralization was achieved in the SM–RS pile. Also, the SM–RS pile exhibited slightly better performance than the DM–RS according to the evolutions of temperature, OM degradation, GI and PGI. The C/N ratio, GI and PGI could be included in the maturity evaluation index system in which GI > 120% and PGI > 1.00 signal mature co-composts.     

Influence of moisture content,particle size and forming temperature on productivity and quality of rice straw pellets

A large amount of rice straw is generated and left as much in paddy fields, which causes greenhouse gas emissions as methane. Rice straw can be used as bioenergy. Rice straw pellets are a promising technology because pelletization of rice straw is a form of mass and energy densification, which leads to a product that is easy to handle, transport, store and utilize because of the increase in the bulk density. The operational conditions required to produce high quality rice straw pellets have not been determined. This study determined the optimal moisture content range required to produce rice straw pellets with high yield ratio and high heating value, and also determined the influence of particle size and the forming temperature on the yield ratio and durability of rice straw pellets. The optimal moisture content range was between 13% and 20% under a forming temperature of 60 or 80 °C. The optimal particle size was between 10 and 20 mm, considering the time and energy required for shredding, although the particle size did not significantly affect the yield ratio and durability of the pellets. The optimized conditions provided high quality rice straw pellets with nearly 90% yield ratio, ?12 MJ/kg for the lower heating value, and >95% durability.     

Canola straw as a bio-waste resource for medium density fiberboard (MDF) manufacture

Canola straw as an agricultural residue has been investigated for MDF production. The variables were steaming time (2, 5 and 8 min), the resin content (9% and 11%), and press time (4 and 6 min). Common physical and mechanical properties of experimental boards including modulus of rupture (MOR), modulus of elasticity (MOE), internal bond strength (IB) and thickness swelling (TS) were measured. Fiber properties of canola straw including length, diameter and cell wall thickness were determined. The results showed that all the tested mechanical properties improved with the increase of steaming time level. The results were close to the minimum requirements of MDF specified in the ANSI A208.2 standard. Dimensional stability of the MDFs improved as adhesive content increased. The IB values are positively affected by the increase of press time. MDF properties made from canola straw possess acceptable qualities as compared to those made from other non-wood plants. Furthermore, the fiber dimensions of canola straw were also in the range of reported values in hardwoods.     

Behaviour of Rice-Byproducts and Optimizing the Conditions for Production of High Performance Natural Fiber Polymer Composites

This present study deals with evaluating some available rice by-products, such as rice straw and rice husks, as a fiber component in manufacturing of high performance natural fiber polymer composites (NFPC). The utilization of these undesirable wastes will contribute to the reduction of the environmental impact of waste disposal by burning. Two matrices (thermoset and thermoplastic) were used. Optimization of manufacture conditions of polyester-based thermosetting polymer composites was carried out through examine the effects of fibers to polymer ratio, amounts of catalyzed and initiator, fraction size of fibers and substituting one fibers by another, as well as time, temperature and pressure of pressing. The possibility of styrene containing polyester solution on improving the fiber interface via in situ grafting and enhancing the strength and water resistance of the produced NFPC was also evaluated, in comparison with that produced from using thermoplastic matrix (polypropylene) in presence of coupling agent. The production of this valuable product (NFPC) by this simple procedure, which not needs special devices (twin extrusion with heater), and chemicals to improve the compatibility between fibers and polymer matrix, will ensure reasonable profits and direct impacts on the Egyptian economy in general and rice growers in particular.     

Wood Plastic Composite Panels: Influence of the Species,Formulation Variables and Blending Process on the Density and Withdrawal Strength of Fasteners

In this work, the influence of four variable parameters including fiber types (poplar and rice straw), fiber contents (45, 60, and 75 wt%), fiber sizes (20–40 and 40–60 mesh), and blending methods (hot-pressing and extrusion) on the physico-mechanical properties of wood plastic composite panels were studied. Generally, the results showed that each of the above-mentioned parameters had significant effect on the nail and screw withdrawal strength (pull-out load) and density, whereas their interactions did not have highly impressive effects on the properties. All tested properties vary significantly with fiber origin. Composites filled with larger fiber size, produced panels with higher withdrawal strength and density. The effect of blending method on density was maximal. Withdrawal strength values of each sample decreased with increase in fiber loading. The lowest withdrawal strength values of nail and screw were obtained from the samples filled with rice straw. It was found that strength properties of the composites can be improved moderately by adding 45 wt% fiber, 20–40 mesh particle and poplar flour. According to the results, the blending method is a significant variable in the determination of withdrawal strength. Therefore, the blending method can be recommended based on the end product applications.     

Increased 3HV Concentration in the Bacterial Production of 3-Hydroxybutyrate (3HB) and 3-Hydroxyvalerate (3HV) Copolymer with Acid-Digested Rice Straw Waste

Bacterial synthesis of 3-hydroxybutyrate (3HB) and 3-hydroxyvalerate (3HV) copolymer [P(3HB-co-3HV)] using the hydrolysate of rice straw waste as a carbon source was affected by the composition of the hydrolysate, which depends highly on the rice straw pretreatment condition. Acid digestion with 2 % sulfuric acid generated larger production of P(3HB-co-3HV) than 6 % sulfuric acid, but 3HV concentration in the copolymer produced with 2 % acid hydrolysate was only 8.8 % compared to 18.1 % with 6 % acid hydrolysate. To obtain a higher 3HV mole fraction for enhanced flexibility of the copolymer, an additional heating was conducted with the 2 % acid hydrolysate after removal of residual rice straw. As the additional heating time increased a higher concentration of levulinic acid was generated, and consequently, the mole fraction of 3HV in P(3HB-co-3HV) increased. Among the conditions tested (i.e., 20-, 40-, 60-min), 60-min additional heating following 2 % sulfuric acid digestion achieved the highest 3HV mole fraction of 22.9 %. However, a longer heating time decreased the P(3HB-co-3HV) productivity, probably due to the increased intermediates concentrations acting as inhibitors in the hydrolysates. Therefore, the use of additional heating needs to consider both the increase in the 3HV mole fraction and the decrease in the P(3HB-co-3HV) productivity.     

Improved biogas production from rice straw by co-digestion with kitchen waste and pig manure

In order to investigate the effect of feedstock ratios in biogas production, anaerobic co-digestions of rice straw with kitchen waste and pig manure were carried out. A series of single-stage batch mesophilic (37 ± 1 °C) anaerobic digestions were performed at a substrate concentration of 54 g/L based on volatile solids (VS). The results showed that the optimal ratio of kitchen waste, pig manure, and rice straw was 0.4:1.6:1, for which the C/N ratio was 21.7. The methane content was 45.9–70.0% and rate of VS reduction was 55.8%. The biogas yield of 674.4 L/kg VS was higher than that of the digestion of rice straw or pig manure alone by 71.67% and 10.41%, respectively. Inhibition of biogas production by volatile fatty acids (VFA) occurred when the addition of kitchen waste was greater than 26%. The VFA analysis showed that, in the reactors that successfully produced biogas, the dominant intermediate metabolites were propionate and acetate, while they were lactic acid, acetate, and propionate in the others.     

Influence of liquid- and solid-state coupling anaerobic digestion process on methane production of cow manure and rice straw

Journal of Material Cycles and Waste Management - Based on the different characteristics of cow manure and rice straw, liquid- and solid-state coupling anaerobic digestion (L-SS-AD) is designed in...     

Structure of chemical components in different compost extracts characterized by chromatogram and spectroscopy analysis and its influence on plant growth promotion

Pig manure rice straw compost was extracted using different extraction methods, and the composition of each extraction was identified by chromatogram and spectroscopy in order to investigate plant growth promoting factors. Compared with direct extraction, aerated and non-aerated fermentation extractions were better for nutrient accumulation, especially for high molecular weight substances. Cucumber yields of aerated fermentation extraction of compost (AFEC) treatment were 16.5 and 57.6?% higher than the direct extraction of compost (DEC) and non-aerated fermentation extraction of compost (NAFEC) treatments. Humic acid-like and fulvic acid-like substances were the main components in all extracts. Furthermore, AFEC showed the most humification and aromatization. Humic substances extracted from AFEC (H-AFEC) increased shoot dry weight by 2.8 and 7.4?%, compared to humic substances extracted from DEC (H-DEC) and humic substances extracted from NAFEC (H-NAFEC). In conclusion, AFEC was the best extraction method to get more humic substances to stimulate plant growth.     

Rice straw-base power generation: a potential and economic cost–benefit analysis for a small power plant (10 MWe) in Vietnam

Journal of Material Cycles and Waste Management - The main objective of the study is to explore the economic feasibility of power generation from rice straw, a potential biomass energy resource, in...     

Low energy comsumption management of agricultural residues

In this paper, a mechanical filtering system to treat pig slurry is proposed. The filter was made from the aerobic decomposition product of the organic fraction of municipal wastes and wheat straw was used as the support.Using a pilot plant to treat 2100 liters of swine slurry, an adequate reduction in BOD₅; COD, and other parameters was obtained. The organic matter content of the material trapped in the filter was similar to that of compost and farmyard manure, but the nitrogen and phosphorous levels and the C/N ratio were more similar to farmyard manure. After passing through a filtering system, the treated liquid can be used for fertirrigation and as a feed for algae ponds. After a period of stabilization, the solid material can be mixed to produce manure. Although wheat straw was used as the support in this experiment, other agricultural wastes such as rice straw, corn stalks, millet stems, banana, cotton, and coconut trash can be used. Rather than municipal solid waste compost, other kinds of compost obtained from agricultural wastes such as leaves, bark, husks, etc., can be used as the filter.     

The mixing and segregation characteristics of rice straw in a cylindrical bubbling fluidized bed

In the present study, an experiment was performed to investigate the mixing and segregation characteristics of standard sand and rice straw particles in a cylindrical bubbling fluidized bed. The mass ratio (rice straw/standard sand = 0.5–1.25 %) of two particles and superficial gas velocity (0.13–0.18 m/s) were changed as experimental variables. The pressure drop curve and Kramer’s equation were used to determine the minimum fluidization velocity and mixing index, respectively. In all cases, the mixing index was the lowest at U/U _mf = 1.15. Based on the point of U/U _mf = 1.15, the segregation region and mixing region were observed. In the segregation region, mass ratio of 0.75 % showed the lowest mixing index. At the U/U _mf = 1.23 which was selected as the starting of fast pyrolysis considering residence time and the previous fast pyrolysis experiment, mass ratio of 1.25 % showed the highest mixing index which was 0.90.     

Morphology,pore size distribution,and nutrient characteristics in biochars under different pyrolysis temperatures and atmospheres

Journal of Material Cycles and Waste Management - To evaluate the agronomic potential of biochar, we prepared a series of biochars using rice straw waste under the limited oxygen cracking condition...     

Composting olive mill pomace and other residues from rural southeastern Spain

The costly disposal of the semisolid residual pomace generated in the two phase extraction used in modern olive mills is causing serious problems to the small oil producers of rural southeastern Spain. Composting may be a viable alternative since complementary residues are usually available in these areas to prepare an adequate starting mixture. In this work, four different combinations of residues (pomace+rabbit manure, pomace+sheep manure, pomace+rabbit manure+rice straw, pomace+rabbit manure+almond shells) were composted in 3 ton piles aerated by turnings, using technology available to any small community of oil producers. During the four long processes (9-10 months), a steady decrease of organic matter and increases in the concentrations of nutrient and humic substances were observed, together with large increases in pH and salinity which may reduce the agronomic value of the final products.     

ENUMERATION OF ANAEROBIC REFUSE-DECOMPOSING MICRO-ORGANISMS ON REFUSE CONSTITUENTS

Hydrolytic, acetogenic and methanogenic bacteria are required for the conversion of refuse to methane in landfills. In order to identify sources of these trophic groups in refuse, the total anaerobic population and the sub-populations of cellulolytic, hemicellulolytic, butyrate catabolizing acetogenic, and acetate- and H₂-CO₂-utilizing methanogenic bacteria as present on grass, leaves, branches, food waste, whole refuse and two landfill cover soils were enumerated by the most probable number (MPN) technique. Total anaerobes ranged from 10³cells per dry gram in cover soil to 10⁹in grass, food waste and fresh refuse. Hemicellulolytics ranged from 160 cells per dry gram in cover soil to 10⁹in grass. The highest cellulolytic population was measured on branches (316 cells per dry gram), while the maximum acetogenic population was measured on leaves (2.5×10⁴). The highest methanogen populations were measured on leaves (6.3×10³) and one of two fresh refuse samples (10⁵). Yard waste was the major carrier of the trophic groups required for refuse decomposition, while the cover soils tested did not represent major inputs of the requisite bacteria to landfills.     

Microbial Degradation of UV-Pretreated Low-Density Polyethylene Films by Novel Polyethylene-Degrading Bacteria Isolated from Plastic-Dump Soil

Eleven effective low-density polyethylene (LDPE)-degrading bacterial strains were isolated and identified from landfill soil containing large amounts of plastic materials. The isolates belonged to 8 genera, and included Pseudomonas (areroginosa and putida), Sphingobacterium (moltivorum), Delftia (tsuruhatansis), Stentrophomonas (humi and maltophilia), Ochrobacterum (oryzeae and humi), Micrococcus (luteus), Acinetobacter (pitti), and Citrobacter (amalonaticus). Abiotic degradation of LDPE films by artificial and natural ultraviolet (UV)-exposure was analyzed by FT-IR spectroscopy. LDPE films treated with UV-radiation were also inoculated with the isolates and biofilm production and LDPE degradation were measured. Surface changes to the LDPE induced by bacterial biofilm formation were visualized by Scanning Electron Microscopy. The most active bacterial isolate, IRN19, was able to degrade polyethylene film by 26.8?±?3.04% gravimetric weight over 4 weeks. Analysis of 16S rRNA sequence of this isolate revealed 96.97% similarity in sequence to Acinetobacter pitti, which has not previously been identified as a polyethylene-degrading bacterium. Also, most the effective biofilm forming isolate, IRN11, displayed the highest cell mass production (6.29?±?0.06 log cfu/cm²) after growth on LDPE films, showed 98.74% similarity to Sphingobacterium moltivourum.