煤泥对水溶液中Ca2+的吸附性能研究

在静态条件下,研究了Ca²⁺在煤泥表面的吸附动力学。考察了不同Ca²⁺初始浓度的吸附实验,并对实验结果进行了动力学方程的拟合,结果表明,煤泥对Ca²⁺的吸附过程较好地符合准二级动力学方程。研究了初始Ca²⁺浓度、溶液pH值、振荡速度和煤泥质量对Ca²⁺吸附量的影响,实验结果表明：（1）煤泥对Ca²⁺吸附量随着Ca²⁺溶液浓度的增加而增大,Ca²⁺浓度大于3.828 mmol/L时,吸附量基本保持不变;（2）溶液pH<9时煤泥颗粒对Ca²⁺的吸附主要是静电吸附,pH>9时Ca²⁺在煤泥表面主要是沉淀吸附和一羟基吸附;(3) Ca²⁺在煤泥表面吸附的最佳振荡强度为150 r/min。     

煤泥对水溶液中Ca^2＋的吸附性能研究

在静态条件下,研究了Ca^2＋在煤泥表面的吸附动力学。考察了不同Ca^2＋初始浓度的吸附实验,并对实验结果进行了动力学方程的拟合,结果表明,煤泥对Ca^2＋的吸附过程较好地符合准二级动力学方程。研究了初始Ca^2＋浓度、溶液pH值、振荡速度和煤泥质量对Ca^2＋吸附量的影响,实验结果表明：（1）煤泥对Ca^2＋吸附量随着Ca^2＋溶液浓度的增加而增大Ca^2＋浓度大于3．828mmol／L时,吸附量基本保持不变;（2）溶液pH〈9时煤泥颗粒对Ca^2＋的吸附主要是静电吸附,pH〉9时Ca^2＋在煤泥表面主要是沉淀吸附和一羟基吸附;（3）Ca^2＋在煤泥表面吸附的最佳振荡强度为150r／min。     

改性糠醛渣吸附脱硫废水中钙离子

石灰石-石膏法烟气脱硫技术中石灰石利用率低导致钙流失严重,为实现脱硫废水中Ca2+的资源化利用,进行糠醛渣改性和Ca2+的吸附特性研究。实验结果表明,利用H3PO4改性后的糠醛渣对脱硫废水中Ca2+具有较高的吸附率;在振荡的前30 min吸附率上升极快,至90 min时基本达到平衡吸附量;对Ca2+浓度对吸附率影响研究结果表明,平衡吸附量与平衡浓度关系符合Langmuir等温吸附方程;在初始Ca2+浓度为300 mg/L的溶液中加入3 g吸附剂,温度30℃条件下振荡90 min,平衡吸附量为8.41 mg/g。     

As(V)在金红石TiO_2颗粒表面吸附特性及机理

通过静态动力学和热力学吸附实验,研究了温度、共存离子以及溶质的初始浓度对As(V)在金红石TiO2颗粒表面吸附的影响,探讨了As(V)在金红石TiO2颗粒表面吸附特性及机理。结果表明,在As(V)初始浓度为10 mg/L,pH为7的条件下,25℃时的吸附量0.41 mg/g高于30℃时的吸附量0.31 mg/g,As(V)在金红石TiO2上的吸附为放热过程。CaCl2和MgCl2的添加对As(V)在金红石TiO2表面吸附起到明显的促进作用。T=25℃,Ca2+或Mg2+浓度为10 mmol/L时,As(V)吸附量分别为0.64和0.56 mg/g,Ca2+比Mg2+对As(V)吸附促进作用强。As(V)在金红石TiO2的吸附等温线符合Frendlich方程,Lagergren二级动力学方程能较好地描述As(V)在金红石TiO2颗粒表面吸附的动力学过程。     

壳聚糖包覆介孔微孔分子筛去除水中的氨氮

以壳聚糖包覆介孔-微孔复合分子筛(CS/MCM-41-A)为吸附剂去除水中的氨氮,研究了反应时间、溶液p H、溶液氨氮初始浓度、CS/MCM-41-A投加量、竞争离子对吸附的影响,分析了CS/MCM-41-A的吸附动力学和热力学特征。结果表明,298 K下,当CS/MCM-41-A投加量为5 g/L,溶液氨氮初始浓度50 mg/L,p H为7,吸附时间为40 min时,溶液中氨氮的去除率达到74.35%,CS/MCM-41-A对离子的选择吸附顺序为Mg2+K+Ca2+Na+。CS/MCM-41-A吸附氨氮符合拟二级动力学方程,吸附等温线更好地符合Freundlich方程,CS/MCM-41-A对氨氮的去除有良好的吸附性能。     

生物膜细菌藻酸盐对Cu2+的吸附动力学研究

以生物膜中提取的细菌藻酸盐为原料制备藻酸钙为吸附剂,对水溶液中的Cu2+进行了吸附动力学研究.试验结果表明,吸附时间、溶液初始pH和吸附剂投加量对藻酸钙吸附Cu2+影响显著.当溶液初始pH为4.0、Cu2+初始质量浓度为100 mg/L、吸附剂投加量为0.7 g/L时,藻酸钙对Cu2+的平衡吸附量为56.15 mg/g.水溶液中Cu2+在藻酸钙上的吸附动力学过程可用准二级动力学方程来模拟.吸附等温线研究表明,藻酸钙吸附Cu2+的过程可用Langmuir和Freundlich模型来描述.100 mmol/L 乙二胺四乙酸(EDTA)可有效解吸95.6%的Cu2+,实现Cu2+的回收与吸附剂的重复利用.     

表面活性剂对多壁碳纳米管吸附Pb~(2+)的影响

多壁碳纳米管(MWNT)在吸附有毒气体和重金属离子方面具有极高的应用价值.针对MWNT对水溶液中Pb2+的净化吸附进行了研究,从吸附量,吸附速率、动力学角度考察了表面活性剂、Pb2+浓度对MWNT吸附Pb2+的影响.结果表明,司班-60、吐温-20、阿拉伯树胶等表面活性剂的加入,促进了MWNT在溶液中的分散,导致在Pb2+摩尔浓度为3～18 mmol/L的Lang-muir和Freundlich等温吸附方程中的吸附常数(K)变大,使得MWNT对Pb2+的吸附速率和平衡吸附量都得到提高;随着溶液中Pb2+浓度的增大,MWNT对其吸附量渐至饱和,随后由于Pb2+的位阻作用.吸附量下降;在这3种表面活性剂中,由于司班-60具有相对较小的分子量,其分散的MWNT在Pb2+摩尔浓度为14 mmol/L时,吸附量最大,为230 mg/g.     

表面活性剂对Cd2+在沉积物上吸附行为的影响

以Cd2+为重金属代表,阴离子表面活性剂十二烷基苯磺酸钠(SDBS)、阳离子表面活性剂氯化十六烷基吡啶(CPC)、非离子表面活性剂辛基酚聚氧乙烯醚(TX-100)为表面活性剂代表,用实验模拟法研究了3种类型的表面活性剂对Cd2+在沉积物上吸附行为的影响.结果表明,不同种类的表面活性剂对Cd2+在沉积物上的吸附影响不同,SDBS对Cd2+的吸附影响可分为2个阶段,当SDBS初始质量浓度从0 mg/L增加到2 600 mg/L,Cd2+的吸附量从1.52 mg/g增至1.88 mg/g,增加了23.7%,随着SDBS初始浓度继续增加,Cd2+的吸附量开始下降,当SDBS初始质量浓度增至16 000 mg/L,Cd2+的吸附量降低至0.34 mg/g;CPC主要通过在溶液中电离出CP+,CP+与Cd2+竞争沉积物表面的吸附位从而抑制Cd2+的吸附,当CPC初始质量浓度从0 mg/L增加至16 000 mg/L,Cd2+的吸附量从1.50 mg/g降低至0.52 mg/g;TX-100能轻微抑制Cd2+在沉积物上的吸附,当TX-100初始质量浓度从0 mg/L增加到16 000 mg/L时,Cd2+吸附量从1.52 mg/g减少至1.35 mg/g.     

苯并三唑在土壤中的吸附特性

为了解苯并三唑(BTA)在水-土系统中的迁移转化,通过批实验方法研究了BTA在华北平原土样(GSS13)中的吸附,考察了平衡时间、土壤投加量、溶液初始p H以及共存阳离子对吸附的影响。结果表明,在初始阶段,土壤对BTA的吸附速率较快,之后随着吸附点位的减少,吸附逐渐变慢;吸附过程符合准二级反应动力学方程。土壤对BTA的平衡吸附为非线性吸附,吸附等温线为Freundlich型;随着土壤投加量的增大,单位质量土壤吸附BTA的量减少,可能原因是所选土壤对BTA的吸附存在"固体浓度效应"。溶液的p H通过改变BTA的存在形式和土壤表面的带电性而影响吸附,当溶液p H在BTA的p Ka2(8.6)附近时,土壤对BTA的吸附效果最好。此外,溶液中共存阳离子对土壤吸附BTA有不同的影响,Na+对吸附影响不明显,而不同浓度Ca2+对BTA的吸附有不同程度的促进作用。     

牛粪生物炭对Cd~(2+)的吸附影响因素及特性

为了考察以牛粪为原料制备的生物炭对水溶液中Cd2+的吸附效果,进行了吸附影响因素、吸附等温线和动力学研究。结果表明,当热解温度为700℃、投加量为20 g/L、溶液初始pH为5、水溶液Cd2+初始浓度为10 mg/L、吸附平衡时间为60 min和溶液温度为25℃时,对Cd2+的吸附效果最佳,Cd2+去除率可达99%以上。提高溶液温度有利于吸附。降低生物炭热解温度和投加量对吸附效果影响不大。Langmuir方程能更好地拟合生物炭对Cd2+的吸附等温过程,吸附过程符合准二级动力学方程。牛粪生物炭是性能优良、价格经济的水溶液中Cd2+的吸附剂。     

Comparative study of adsorption of Pb(II) on native garlic peel and mercerized garlic peel

A comparative study using native garlic peel and mercerized garlic peel as adsorbents for the removal of Pb²⁺ has been proposed. Under the optimized pH, contact time, and adsorbent dosage, the adsorption capacity of garlic peel after mercerization was increased 2.1 times and up to 109.05 mg g^?1. The equilibrium sorption data for both garlic peels fitted well with Langmuir adsorption isotherm, and the adsorbent–adsorbate kinetics followed pseudo-second-order model. These both garlic peels were characterized by elemental analysis, Fourier transform infrared spectrometry (FT-IR), and scanning electron microscopy, and the results indicated that mercerized garlic peel offers more little pores acted as adsorption sites than native garlic peel and has lower polymerization and crystalline and more accessible functional hydroxyl groups, which resulted in higher adsorption capacity than native garlic peel. The FT-IR and X-ray photoelectron spectroscopy analyses of both garlic peels before and after loaded with Pb²⁺ further illustrated that lead was adsorbed on the through chelation between Pb²⁺ and O atom existed on the surface of garlic peels. These results described above showed that garlic peel after mercerization can be a more attractive adsorbent due to its faster sorption uptake and higher capacity.     

皂化改性橘子皮生物吸附剂对重金属离子的吸附

以生物废料橘子皮(OP)为原料,经乙醇、氢氧化钠处理,得到改性橘子皮生物吸附剂SOP,将其用于对重金属离子Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的吸附。研究了溶液pH、吸附时间和重金属离子初始浓度对SOP吸附性能的影响。结果表明,重金属离子在生物吸附剂上的吸附速率快,符合准二级动力学方程。SOP对重金属离子的吸附等温线符合Lang-muir模型,根据Langmuir模型计算SOP对Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的饱和吸附量分别为56.82、152.4、66.27、33.90和23.02 mg/g,均高于改性前。常见阳离子的存在对重金属离子吸附的影响较小,改性后的橘子皮生物吸附剂可以再生重复使用4次以上,是性能良好的重金属离子吸附剂。     

天然及CaCl2改性沸石对四环素的吸附

通过静态吸附实验研究了水中四环素在天然和CaCl2改性沸石上的吸附行为及机制。实验表明,天然沸石对四环素具有吸附能力,CaCl2改性可以提高沸石对四环素的吸附能力。天然和改性沸石对四环素的吸附符合拟二级动力学模型,颗粒内扩散不是吸附过程的主要控制步骤。Freundlich和Dubinin-Radushkevich(D-R)等温吸附模型可以较好地描述实验所用2种沸石对四环素的吸附行为,D-R等温方程拟合结果显示吸附过程包含离子交换作用。通过对天然和改性沸石吸附四环素前后溶液中主要阳离子浓度变化分析证实了该吸附过程包含离子交换作用。实验研究了pH值变化对沸石吸附四环素的影响,当pH=3～5时,天然和改性沸石对四环素的吸附量均随pH值的增加而急剧下降,而pH=5～10时,天然和改性沸石对四环素的吸附量变化均不明显,推测可能是离子交换作用和化学沉淀吸附作用所致。另外,实验还初步探索了溶液离子强度对沸石吸附四环素的影响情况,随着溶液中Na+和Ca2+离子强度的增加,吸附量先急剧降低随后趋向平稳,进一步说明了沸石对四环素的吸附过程不是由单一机制控制的。     

改性荞麦壳对水溶液中Cu~(2+)离子吸附效果及机理

以柠檬酸对荞麦壳进行化学改性,改性后荞麦壳吸附剂对Cu2+的吸附量增加。研究了不同pH、吸附剂投入量、浓度和时间对吸附效果的影响。在pH值为5.5,Cu2+初始浓度50 mg/L,吸附剂投入量为1 g,吸附时间为120 min的条件下,Cu2+的吸附量达到较大值。通过用改性荞麦壳吸附剂对Cu2+的热力学吸附过程的分析,结果表明,改性荞麦壳吸附剂符合Langmuir吸附等温模式,改性荞麦壳吸附剂对Cu2+的吸附存在化学吸附,改性荞麦壳的最大吸附量可以达2.26 mg/g。研究改性荞麦壳吸附剂吸附Cu2+的动力学特性,吸附动力学行为可用准二级速率方程进行很好的描述,准二级吸附速率常数随温度升高而增大。准一级速率方程和颗粒扩散模型可以较好地描述吸附初始阶段,Cu2+浓度较高,颗粒内扩散;吸附后期,Cu2+浓度较低,受到颗粒外扩散的控制。总之,整个吸附过程可能是多种动力学机理共同作用的结果。     

矸石基X型分子筛对水中Co2+、Cu2+、Cd2+和Cr3+的去除

以煤矸石为原料,采用碱熔后水热合成法制备X型分子筛并进行XRD、SEM、BET和Zeta电位分析。研究其对水中Co2+、Cu2+、Cd2+和Cr3+4种离子的吸附性能,包括吸附等温线、吸附动力学以及初始金属离子浓度、pH值对吸附性能的影响。所合成的矸石基X型分子筛的BET比表面积为676.02 m2/g,微孔孔容为0.263 cm3/g。吸附实验表明,矸石基X型分子筛能有效去除上述4种离子,同时实现煤矸石的资源化和金属离子的去除。4种离子的平衡吸附量均随初始浓度的增大而增大,相同条件下平衡吸附量的大小顺序为Cd2+>Cr3+>Cu2+>Co2+。准二级动力学模型能很好地描述4种离子的吸附动力行为。Langmuir模型对Co2+、Cu2+和Cd2+吸附的拟合较Freundlich模型高,说明其主要表现为物理吸附过程。4种离子的吸附速率均由液膜扩散和颗粒内扩散共同控制。     

Effect of anions and cations on cadmium sorption kinetics from aqueous solutions by chitin: experimental studies and modeling

The effect of ions, including Na(+), Mg(2+), Ca(2+), Cl(-), SO(4)(2-) and CO(3)(2-), at various initial concentrations, on the kinetics of cadmium sorption by chitin was studied at 25 degrees C and free initial pH solution in batch conditions. The presence of these ions in solution was found to inhibit the uptake of cadmium by chitin to different degrees: sodium and chloride ions have no significant effect. For Mg(2+), Ca(2+), SO(4)(2-) and CO(3)(2-) ions, the effects ranged from a large inhibition of cadmium by Ca(2+) and CO(3)(2-) to a weak inhibition by Mg(2+) and SO(4)(2-). These results indicate that the uptake sites of these ions are the same. No ion was found to enhance cadmium uptake. The results also showed that the kinetics of sorption are best described by a pseudo second-order expression than a first or second-order model.     

天然土壤对水溶液中Pb~(2+)的吸附

以天然土壤为吸附材料,处理水溶液中的Pb2+,研究3种土壤对水溶液中Pb2+的吸附过程并结合土壤的理化性质对吸附规律进行初步分析。结果表明,棕壤和钙层土对Pb2+的吸附能力远大于红壤,3种土壤对Pb2+的吸附动力学曲线与二次动力学方程有较好的拟合性;3种土壤吸附Pb2+的吸附等温线用Langmuir方程描述最为合适,其次是Temkin方程,再次是Frenudlich方程,钙层土对Pb2+的吸附受温度影响较为明显;由实验数据得出的反应热力学参数说明3种土壤对Pb2+的吸附是自发的吸热过程;Pb2+在饱和吸附的土壤表面覆盖率并不高;土壤对Pb2+的吸附能力受各种土壤理化性质的综合影响。     

Use of carbonised beet pulp carbon for removal of Remazol Turquoise Blue-G 133 from aqueous solution

Carbonised beet pulp (BPC) produced from agricultural solid waste by-product in sugar industry was used as adsorbent for the removal of Remazol Turquoise Blue-G 133 (RTB-G 133) dye in this study. The kinetics and equilibrium of sorption process were investigated with respect to pH, temperature and initial dye concentration. Adsorption studies with real textile wastewater were also performed. The results showed that adsorption was a strongly pH-dependent process, and optimum pH was determined as 1.0. The maximum dye adsorption capacity was obtained as 47.0 mg g^?1at the temperature of 25 °C at this pH value. The Freundlich and Langmuir adsorption models were used for describing the adsorption equilibrium data of the dye, and isotherm constants were evaluated depending on sorption temperature. Equilibrium data of RTB-G 133 sorption fitted very well to the Freundlich isotherm. Mass transfer and kinetic models were applied to the experimental data to examine the mechanisms of adsorption and potential rate-controlling steps. It was found that both external mass transfer and intra-particle diffusion played an important role in the adsorption mechanisms of dye and adsorption kinetics followed the pseudo second-order type kinetic model. The thermodynamic analysis indicated that the sorption process was exothermic and spontaneous in nature.     

The sorption of airborne pollutants on natural and synthetic surfaces: correlation to the mathematical models

The laboratory experiments were carried out to study the sorption process of gaseous toluene in the peel of different fruits as well as in the chemically prepared material based on silica support (multiligand-adsorbent). For the sorption experiments, a vapor generating system was used that allows the exposure of sorbents to a constant flux of polluted air. The concentration of toluene in the tested sorbents was followed as a function of exposure time. The obtained results were correlated to the mathematical models describing the sorption kinetics in the leaves. The investigation with the plant material showed dual-phase behavior of the toluene partition ('mixed' sorption mechanism), in the case of multiligand-adsorbent a typical adsorption process was observed. Sorption kinetics to fruit material was well correlated to the two-compartment model, while for the chemically prepared material to the first-order model.