活必炭纤维的表面结构及其吸附模式

迄今的吸附模式,Ｈｅｎｒｙ定律、Ｌａｎｇｍｕｉｒ模型、ＢＥＴ模型、Ｄ－Ｒ方程、Ｄ－Ａ方程都分别适用于不同的表面结构。对于活性炭纤维（ＡＣＦ）这种特殊的炭吸附材料适用于哪种吸附模型,未见有文献专题论述。本论文在对ＡＣＦ材料进行了大量表面结构研究的基础上,对ＡＣＦ的表面结构与颗粒活性炭（ＧＡＣ）的表面进行了对比,并尝试性地对适用于ＡＣＦ的吸附模式进行了计算和比较,得到了一些有价值的结论。     

活性炭及活性炭纤维对CS2的吸附行为研究及其方法探讨

以活性炭纤维(ACF)对水中CS:的吸附处理作为研究对象,并与另外两种活性炭(颗粒活性炭GAC和粉末活性炭PAC)进行对比研究,展示了ACF对CS:的优异吸附性能与处理效果,即吸附容量大,吸附低浓度效果好.同时运用新的宽平衡浓度吸附试验方法,测试了ACF、GAC、PAC对CS2的吸附平衡曲线,并对几种常见的吸附等温方程...     

活性炭纤维对水中敌草隆的吸附性能

探讨了活性炭纤维对水中敌草隆的吸附．结果表明,在pH=2．9时,吸附量最大;活性炭纤维的吸附能力随着温度的升高而升高;Redlich．Peterson方程更适合描述敌草隆的吸附行为;Gibbs自由能（△G0）值小于零,说明此吸附过程是自发进行的吸附过程;假二级方程更适用于描述活性炭纤维对水中敌草隆的吸附动力学过程．     

纳米氧化石墨烯对水中锶的吸附特征

采用纳米氧化石墨烯(GO)吸附放射性废水中Sr2+,从吸附原理、吸附动力学、pH对吸附的影响等方面对吸附过程进行研究.采用表面增强拉曼技术和红外光谱对Sr2+在GO表面的吸附进行光谱表征.将GO负载到活性炭表面进行柱实验探索GO在废水处理中的应用.结果表明,在pH值为6.0—6.5时GO对Sr2+的吸附符合Langmuir吸附模型,最大吸附量263.16mg·g-1.GO对Sr2+的吸附符合拟二级动力学方程.在pH3—11范围内吸附量随着pH升高显著增大.GO对Sr2+的吸附具有快速,吸附量大,适用pH范围广的特点,可大量用于放射性废水的处理.GO负载到活性炭上后吸附量有所下降,但克服了GO材料本身在水中粒径小难分离的缺陷,是一种可实际应用、去除环境中Sr2+的新方法.     

生物可降解络合剂[S,S]-乙二胺二琥珀酸改性蛭石和活性炭及其对Fe(Ⅱ)的吸附性能

提出将Fe(Ⅱ)离子吸附络合稳定于活性炭、蛭石表面,再与H2O2组成新的非均相Fenton反应体系,通过加热、煮沸、干燥等简单的物理方法成功地将螯合剂EDDS([S,S]-乙二胺二琥珀酸)修饰到蛭石和活性炭表面,对蛭石和活性炭进行改性.主要研究了包括pH、温度、初始浓度、反应时间对材料吸附性能的影响.研究表明,在相同条件下EDDS改性可以提高活性炭和蛭石对Fe(Ⅱ)离子的吸附容量,溶液pH、温度、初始浓度对吸附有较大影响.吸附等温线的拟合结果表明,Fe(Ⅱ)离子在EDDS修饰的活性炭和蛭石上吸附行为符合Langmuir吸附,其饱和吸附量都有所提高,且具有较大的吸附系数,这是由于修饰在活性炭和蛭石表面的EDDS和金属离子形成强烈的络合作用所致.     

改性活性炭的表面特性及其对金属离子的吸附性能

本文主要研究了改性对活性炭的表面物理化学特征和对其吸附金属离子性能的影响。研究发现,硝酸氧化可显著增加活性炭表面酸性基团的含量,提高活性炭的表面亲水性,降低pHpzc值,并造成活性炭的结构塌陷和比表面积的减少,因而对活性炭吸附性能产生明显影响,可明显提高对Pb^2 等金属离子的吸附容量。     

改性活性炭对有机物的吸附性能

研究了表面改性对活性炭吸附各种有机物性能的影响,研究发现,硝酸氧化可显著增加活性炭表面酸性基团的含量,提高了活性炭的表面亲水性,降低pHpzc值,并造成活性炭的结构塌陷和比表面积的减少,因而对活性炭吸附水中的苯酚、苯胺、腐殖酸、氯仿、四氯化碳等有机物的性能产生明显影响,以去除水中有机污染物为目的的活性炭表面改性的方向应为：减少表面内酯基及竣基等含氧官能团的含量,增加活性炭表面的疏水性。     

互花米草活性炭对镉的吸附

进行了磷酸活化法不同浸渍比（0.5—3.0）及活化温度（400℃—700℃）条件下制备的互花米草活性炭对镉的吸附性能研究,采用静态吸附法,考察不同初始浓度条件下活性炭对镉的平衡吸附量,旨在探索吸附机理、影响因素、除镉吸附剂的最佳制备条件以及活性炭物化性质对镉吸附性能的影响.实验表明,浸渍比和活化温度是影响成品活性炭镉吸...     

TiO2/活性炭催化剂对4-CP的吸附和光催化活性

采用常压金属有机物化学气相沉积技术在活性炭表面沉积构成纳米TiO2催化剂,XRD分析表明,沉积在活性炭表面的TiO2为锐钛矿晶型.TEM分析表明负载量为8%(wt)时,TiO2颗粒的粒径为10-20nm;载体负载前后BET面积仅改变了6%,表明负载TiO2后对活性炭的结构影响不大.利用Langmuir-Hinshelwood动力学模型探讨了TiO2/活性炭催化剂对4-CP的吸附行为和光催化活性之间的关系,求出4-CP降解反应速率常数Kr,在紫外光照条件下催化剂对4-CP的吸附明显增强.     

提高甲醛吸附速率的活性炭表面改性及评估方法

通过负载多羟基和胺基化合物来对活性炭表面进行官能团修饰,可提高活性炭在大风量和高空速下对甲醛污染物的吸附速率.实验考察了基炭孔结构参数,改性剂负载量,改性炭制备条件等因素对活性炭吸附甲醛性能提升的影响,并介绍了一种测定甲醛吸附速率的装置和方法,用来评估和筛选家用净化器用的活性炭.结果表明,对于四氯化碳值为76%的活性炭,采用等量浸渍的方法制备改性炭的优化条件为:空气气流下的200℃氧化处理,6%的改性剂负载量和不超过100℃的烘干处理温度.本文还通过实验验证和分析,提出和明确了此类表面改性活性炭对甲醛的吸附机理.     

Recovery efficiency of the hydrofluorocarbon (HFC‐134a) by activated carbons of different physicochemical properties

The adsorption characteristics of 1,1,1,2‐tetrafluoroethane (HFC‐134a) on activated carbon were investigated to evaluate the recovery efficiency of HFC‐134a by six activated carbons (two granular activated carbons (GAC1 and GAC2), one high‐surface area activated carbon (HAC), and three activated carbon fibers (ACF10, ACF15, and ACF20)). HFC‐134a adsorption on the activated carbons increased with increase in the specific surface area and pore volume of the activated carbon. The differential heat of the HFC‐134a adsorption decreased with increase in the percentage of the micropore volume to the total pore volume. The adsorption model of HFC‐134a on the activated carbon could be based on the Langmuir model. The constant a of the Langmuir plot of HAC and ACF20 is smaller than GAC1 or GAC2 and ACF10 or ACF15, respectively. The constant W_s of HAC has the largest value. The constant a was correlated to the heat of adsorption. It is concluded that the largest amount of HFC‐134a was adsorbed on HAC, and the least amount of interaction occurred between HFC‐134a and the HAC. The amount of HFC‐134a adsorbed on the activated carbons over time was applied to the Sameshima equation. The adsorption rate constant of HFC‐134a on HAC was the largest. The HAC could be suitable for the recovery of HFC‐134a.     

A Cu-modified active carbon fiber significantly promoted H2S and PH3 simultaneous removal at a low reaction temperature

• Cu_0.15-ACF performs the best for H₂S and PH₃ simultaneous removal. • 550°C and 90°C are separately calcination and reaction temperatures. • The reason why Cu_0.15/ACF shows better performance was found. • The accumulation of H₂PO₄⁻ and SO₄²⁻(H₂O)₆ is the deactivation cause of Cu_0.15/ACF. Poisonous gases, such as H₂S and PH₃, produced by industrial production harm humans and damage the environment. In this study, H₂S and PH₃ were simultaneously removed at low temperature by modified activated carbon fiber (ACF) catalysts. We have considered the active metal type, content, precursor, calcination, and reaction temperature. Experimental results exhibited that ACF could best perform by loading 15% Cu from nitrate. The optimized calcination temperature and reaction temperature separately were 550°C and 90°C. Under these conditions, the most removal capacity could reach 69.7 mg/g and 132.1 mg/g, respectively. Characterization results showed that moderate calcination temperature (550°C) is suitable for the formation of the copper element on the surface of ACF, lower or higher temperature will generate more cuprous oxide. Although both can exhibit catalytic activity, the role of the copper element is significantly greater. Due to the exceptional dispersibility of copper (oxide), the ACF can still maintain the advantages of larger specific surface area and pore volume after loading copper, which is the main reason for better performance of related catalysts. Finally, increasing the copper loading amount can significantly increase the crystallinity and particle size of copper (oxide) on the ACF, thereby improving its catalytic performance. In situ IR found that the reason for the deactivation of the catalyst should be the accumulation of generated H₂PO₄⁻ and SO₄²⁻(H₂O)₆ which could poison the catalyst.     

载铜活性炭纤维Cu-ACF的微观结构与表面形态

本文讨论了载铜活性炭纤维的制备过程与微观结构,表面形态的关系。     

活性碳纤维在环境保护中的应用

由于活性碳纤维的吸附面积大,可以作为固相微萃取的纤维用于对环境污染物质的分析检测,包括含硫和含氯的一些有机化合物.同时,活性碳纤维具有良好的导电性能,可以作为电极,能有效地去除环境中城市污水、燃料废水和腐植酸的污染.     

Effect of denitrifying bacteria on the electrochemical reaction of activated carbon fiber in electrochemical biofilm system

An electrochemical-activated denitrifying biofilm system consisting of activated carbon fiber electrodes immobilized with denitrifying bacteria film as cathode was studied. A revised model for an electrochemical-activated denitrifying biofilm was developed and validated by electrochemical analysis of cathodal polarization curves and nitrate consumption rate. The cathodal polarization curve and nitrate consumption rate were introduced to verify the rate of electrochemical reaction and the activity of denitrifying bacteria, respectively. It was shown that the denitrification process effectively strengthened the electrochemical reaction while the electron also intensified denitrification activity. Electron was transferred between electrochemical process and biological process not only by hydrogen molecule but also by new produced active hydrogen atom. Additionally, a parameter of apparent exchange current density was deprived from the cathodal polarization curve with high overpotential, and a new bio-effect current density was defined through statistical analysis, which was linearly dependent to the activity of denitrification bacteria. Activated carbon fiber (ACF) electrode was also found to be more suitable to the electrochemical denitrifying system compared with graphite and platinum.     

活性碳纤维的应用

本文在比较活性碳纤维与活性碳的结构和吸附特点的基础上,综述了这种吸附材料在废水处理,饮用水净化,空气净化,溶剂回收等各个领域的应用。     

Potential of rice husk ash in atrazine removal

An experimental study was carried out to explore the possibility of using a prepared microporous material, Rice Husk Ash (RHA) as an alternative to the commercial Powdered Activated Carbon (PAC), to remove atrazine (ATZ) pesticide from aqueous solution. The effects of contact time and pH on the adsorption were studied using the batch technique. Based on Hückel model calculations, the zwitterion behaviour of atrazine molecule was proved to be related to the pH of zero charge point of adsorbents (6.8 for RHA and 8.2 for PAC). The results showed that the Pseudo Second Order model is applicable to both adsorbents, suggesting that chemisorption is the rate-limiting step. The equilibrium data fitted well with the Langmuir model in the case of RHA, whereas the Freundlich model better fitted the equilibrium data in the PAC case, suggesting the existence of multi-layer adsorption of atrazine. The adsorption for RHA was found to be feasible and spontaneous, with a removal capacity of atrazine of more than 7?mg?g^?1. With regard to the BET surface, this removal capacity (50.5?µg_ATZ / m²_RHA) was 25% better than that PAC (37.75µg_ATZ / m²_PAC).     

Influence of environmental temperature and relative humidity on photocatalytic oxidation of toluene on activated carbon fibers coated TiO

TiO₂ supported on active carbon fiber (TiO₂/ACF), an absorbable photocatalyst, is a new kind of material applied in air purification. In this paper, the influence of environmental temperature (T) and relative humidity (RH) on the gas-solid adsorption of toluene and the photocatalytic oxidation (PCO) efficiency of adsorbed toluene on TiO₂/ACF were studied, and then, the purification capability of TiO₂/ACF was estimated. PCO results showed that although the PCO efficiency increased under high RH and T levels, the amount of adsorption of toluene decreased. Moreover, quantitative analysis results of intermediates indicated that more environmental risk emerged when PCO of toluene was carried out at higher environmental T and RH levels because more toxic intermediates would be accumulated on the TiO₂/ACF. So, it is significant to control the environmental T and RH conditions in the application of the PCO technique. T = 25°C and RH = 30% is the optimal condition for purifying toluene in our experimental system.     

Influence of environmental temperature and relative humidity on photocatalytic oxidation of toluene on activated carbon fibers coated TiO2

TiO₂ supported on active carbon fiber (TiO₂/ACF), an absorbable photocatalyst, is a new kind of material applied in air purification. In this paper, the influence of environmental temperature (T) and relative humidity (RH) on the gas-solid adsorption of toluene and the photocatalytic oxidation (PCO) efficiency of adsorbed toluene on TiO₂/ACF were studied, and then, the purification capability of TiO₂/ACF was estimated. PCO results showed that although the PCO efficiency increased under high RH and T levels, the amount of adsorption of toluene decreased. Moreover, quantitative analysis results of intermediates indicated that more environmental risk emerged when PCO of toluene was carried out at higher environmental T and RH levels because more toxic intermediates would be accumulated on the TiO₂/ACF. So, it is significant to control the environmental T and RH conditions in the application of the PCO technique. T = 25°C and RH530% is the optimal condition for purifying toluene in our experimental system.