Degradation Kinetics of Biodegradable Fiber Composites

In a composite, fast degradable fibers determine the degradation of the slowly degradable matrix. Such biodegradable composites consisting of degummed hemp fibers and a polyester amide matrix were produced with fiber mass fractions between 0 and 0.48. The hot-pressed plates, 1-mm thick, were incubated in a standard soil. The degradation kinetics was quantified by the measurement of CO₂ production. Furthermore, after termination of experiment, the carbon balance was uncovered. The results were fitted to an exponential law taking into account the degradation of fibers. The increased amount of pores realized by high fiber contents induces pronounced degradation. The degradation is fully characterized by the time constant , which is correlated to the fiber mass fraction. The model allows to predict the degradation kinetics of composites with a few well-defined experiments.     

Processing and Morphology Impacts on Mechanical Properties of Fungal Based Biopolymer Composites

Fungal based biopolymer matrix composites with lignocellulosic agricultural waste as the filler are a viable alternative for some applications of synthetic polymers. This research provides insight into the impact of the processing method and composition of agriwaste/fungal biopolymer composites on structure and mechanical properties. The impact of nutrition during inoculation and after a homogenization step on the three-point bend flexural modulus and strength was determined. Increasing supplemental nutrition at inoculation had little effect on the overall composite strength or modulus; however, increasing carbohydrate loading after a homogenization step increased flexural stress at yield and bulk flexural modulus. The contiguity of the network formed was notably higher in the latter scenario, suggesting that the increase in modulus and strength of the final composite after homogenization was the result of contiguous hyphal network formation, which improves the integrity of the matrix and the ability to transfer load to the filler particles.     

Wood Modification Effects on Weathering of HDPE-Based Wood Plastic Composites

The effects of weathering on the constituents of wood and polymer matrix behavior in wood plastic composites (WPCs) were investigated. WPCs were produced from pine, extractives-free pine, and pine holocellulose fibers (60%) together with HDPE (40%). These composites were subjected to xenon-arc accelerated and outside weathering for a total of 1200 h and 120 days, respectively. The color and chemical changes that occurred on the surface of the WPCs were analyzed using a set of analytical techniques. For pine and extractive-free pine filled composites, the results showed that the total color change, lightness, and oxidation increased, while the lignin content decreased. In addition, the weight average molecular weight (Mw) and number average molecular weight (Mn) of extracted HDPE decreased with an increase in exposure time of the composites. However, HDPE crystallinity increased with longer exposure time. Lightness of holocellulose-based WPC changed the least while the change in its HDPE crystallinity was not significant compared to the other composite types. Therefore, holocellulose-based WPC may be preferred for applications where color stability is of high priority.     

Enhanced Interfacial Adhesion and Characterisation of Recycled Natural Fibre-Filled Biodegradable Green Composites

The structural, thermal, mechanical, and biodegradable properties of composite materials made from polylactide (PLA) and agricultural residues (arrowroot (Maranta arundinacea) fibre, AF) were evaluated. Melt blended glycidyl methacrylate-grafted polylactide (PLA-g-GMA) and coupling agent-treated arrowroot fibre (TAF) formed the PLA-g-GMA/TAF composite, which had better properties than the PLA/AF composite. The water resistance of the PLA-g-GMA/TAF composite was greater than that of the PLA/AF composite; the release of PLA in water from the PLA/AF and PLA-g-GMA/TAF composites indicated good biological activity. The PLA-g-GMA/TAF material had better mechanical properties than PLA/AF. This behaviour was attributed to better compatibility between the grafted polymer and TAF. The results indicated that the T_g of PLA was increased by the addition of fibre, which may have improved the heat resistance of PLA. Furthermore, the mass losses following burial in soil compost indicated that both materials were biodegradable, especially at high levels of AF or TAF substitution.     

Biodegradable Blends Based on Starch and Poly(Lactic Acid): Comparison of Different Strategies and Estimate of Compatibilization

Finding plastic substitutes based on sustainability, especially for short-term packaging and disposable applications has aroused scientific interest for many years. Starch may be a substitute for petroleum based plastics but it shows severe limitations due to its water sensitivity and rather low mechanical properties. To overcome these weaknesses and to maintain the material biodegradability, one option is to blend plasticized starch with another biodegradable polymer. To improve both the compatibility between the main phases and the performance of the final blend, different compatibilization strategies are reported in literature. However, the relative efficiency of each strategy is not widely reported. This paper presents three different strategies: in situ (i) formation of urethane linkages; (ii) coupling with peroxide between starch and PLA, and (iiii) the addition of PLA-grafted amylose (A-g-PLA) which has been elaborated ex situ and carefully analyzed before blending. This study compares the effect of each compatibilization strategy by investigating mechanical and thermal properties of each blend. Compatibilizing behavior of the A-g-PLA is demonstrated, with a significant increase (up to 60%) in tensile strength of starch/PLA blend with no decrease in elongation at failure.     

The Shape Memory Properties of Biodegradable Chitosan/Poly(l-lactide) Composites

The shape memory behavior of PLLA (poly(l-lactide)) and chitosan/PLLA composites was studied. PLLA and chitosan were compounded to fabricate novel materials which may have biodegradability and biocompatibility. Chitosan does not significantly affect the glass and melting transition temperature of the PLLA. Both the pure PLLA and chitosan/PLLA composites showed shape memory effect arising from the viscoelastic properties of PLLA comprised of semi crystalline structures. The shape recovery ratio of the chitosan/PLLA composites decreased significantly with increasing chitosan contents due to the incompatibility between PLLA and chitosan. Phase separation structures of the composites were observed by using atomic force microscopy. To obtain good shape memory effect, the chitosan content should be below 15 wt%.     

Mechanical Performance and Design Criteria of Biodegradable Low-tunnel Films

The overall mechanical behaviour of a series of experimental Mater-Bi made thin low-tunnel films is analysed with respect to the effect of two major factors: the film processing optimisation during manufacturing and the design of the low-tunnels structural system. The analysis of the mechanical behaviour of the biodegradable low-tunnel films, based on the results of extensive full-scale and small-scale experiments, combined with laboratory testing of the mechanical properties of the film, proves that a rather good mechanical behaviour is possible for these films, comparable to the behaviour of conventional agricultural films in terms of strength, provided that two criteria are met: (a) the low tunnel structural design is based on the initial stress at yield value of the film, which represents the asymptotic value of the tensile strength of the film, following its evolution with the time of exposure to real field conditions; (b) the processing of the film is optimised for the particular biodegradable material and film thickness under consideration. It is also confirmed that the stabilisation schemes used with conventional polyethylene films are not suitable for the biodegradable films.

Recycling Ability of Biodegradable Matrices and Their Cellulose-Reinforced Composites in a Plastic Recycling Stream

The effect of multiple injection-moulding reprocessing of three biodegradable matrices on their mechanical properties, melt flow rate, molecular weight, phase transition temperatures and degradation temperature is presented. It has been found that, with successive reprocessing, tensile, flexural and impact strength decreased. Drop in mechanical properties has been assigned to degradation of the matrices, as corroborated by melt flow and molecular weight analysis. Although reprocessing did not significantly affect the glass transition, it diminished the melting point and degradation temperature of polymers. Results indicate that neat PLLA can be recycled for up to five times without suffering a drastic loss in mechanical and thermal properties. The aliphatic polyester Mater-Bi TF01U/095R can be recycled for up to 10 times, whilst starch-based Mater-Bi YI014U/C wastes should be destined to composting, since its recyclability is very poor. The effect of reprocessing on composites reinforced with chemithermomechanical pulp (CTMP) followed the tendencies observed for the neat matrices. Whilst CTMP-fibres behave mainly as filler in PLLA composites, reinforced thermoplastic starch-based composites presented enhanced mechanical properties and recyclability.     

Degradation Behaviour and Field Performance of Experimental Biodegradable Drip Irrigation Systems

The field performance of experimental biodegradable drip irrigation thin wall and regular pipes was investigated through three sets of full-scale experiments and in the laboratory. These experimental biodegradable drip irrigation systems were produced through the processing of biodegradable under real soil conditions polymers, Mater-Bi and Bioflex. The mechanical behaviour of the biodegradable thin wall pipes during the irrigation period was more unstable when compared to the corresponding behaviour of the rigid pipes. The tensile strength of the Mater-Bi and Bioflex thin wall pipes remained almost constant during the total exposure time, except from the folding areas. During the first 7–23 days of exposure in the field, the thin wall pipes had already lost more than the 50% of their initial elongation at break value due to degradation. However, their hydraulic performance began to decline only after a period of 100–120 days with the simultaneous formation of the first cracks. Likewise, the majority of the series of biodegradable rigid pipes exhibited a remarkable reduction in their elongation at break values in the transverse direction within the first 2 weeks. Despite the significant drop of the elongation at break, all biodegradable rigid pipes generally retained their tensile strength as well as a satisfactory hydraulic performance during almost the whole duration of their exposure. A few premature leakages in some points adjoining the drippers were observed after 8–10 weeks of exposure.     

Outdoor Weathering Evaluation of Carbon-Black-Filled, Biodegradable Copolyester as Substitute for Traditionally Used, Carbon-Black-Filled, Nonbiodegradable, High-Density Polyethylene Mulch Films

Carbon-black-filled, biodegradable, copolyester mulch film (Eastar®, or EA, Tennessee Eastman, Kingsport, TN) and commercial carbon-black-filled, high-density polyethylene (HDPE) mulch film were exposed for 12 weeks to commercial vegetable crop growing conditions by being placed directly on irrigated soil in the field of the University of Tennessee Alcoa Highway State Agriculture Experiment Station (Knoxville, TN) and by being placed on a plywood exposure rack as described by the American Society of Testing and Materials (ASTM) Standard Test Method 1435: Outdoor Weathering of Plastics. Mechanical properties and weather information were collected in order to evaluate the feasibility of using the newly developed biodegradable EA mulch film to replace the nonbiodegradable HDPE mulch film. Results indicate that the EA mulch film exhibited favorable tensile strength and elongation-at-break during outdoor exposure rack testing and outdoor, in-field, placed directly on the soil, exposure testing, suggesting biodegradable EA could be a substitute for the HDPE nonbiodegradable material.     

Eco-Friendly Synthesis and Antimicrobial Performance of New Heteropolymer Composites

Journal of Polymers and the Environment - Heteropolymeric materials of resorcinol, aniline, urea, and formaldehyde are synthesized by 1:1:1:3 molar ratios of the respective monomers with different...     

Processing and Characterization of Short-Fiber Reinforced Jute/Poly Butylene Succinate Biodegradable Composites: The Effect of Weld-Line

Fabrication of complex injection molded parts often involves the use of multiple gates. In such situations, polymer melts from different gates meld to form the molded part (weld line). This paper reports on the fabrication and characterization of the mechanical and morphological properties of short fiber reinforced jute/poly butylene succinate (PBS) biodegradable composites. The effect of a dual gated mold in the fabrication of welded specimens was a key focus of the investigation. It was observed that incorporation of jute fiber (10 wt%) conferred drastic changes on the stress–strain properties of the matrix as the elongation at break (EB), dropped from 160% in the matrix to just 10% in the composite. The tensile strength of the composite was lower than that of the matrix. However, it is noteworthy that the tensile modulus of the composite increased. Bending test also revealed that both bending strength and modulus increased with the incorporation of jute. Morphological studies of the tensile fracture surface using SEM revealed two types of failure mode. Ductile failure was indicated by plastic deformation at the initiation of fracture followed by brittle failure. The good interfacial bonding indicated between jute and PBS was attributed to positive interaction between the two polar polymers. A comparison of the non-weld and weld-line samples revealed that the weld-line composites have better mechanical integrity than the corresponding polymer matrix with weld line. The results also revealed that elongation at break and toughness are most sensitive to the presence of the weld-line whereas flexural properties are least sensitive.     

Effect of Glycerin and Starch Crosslinking on Molecular Compatibility of Biodegradable Poly(lactic acid)-Starch Composites

Poly(lactic acid) (PLA) is a biodegradable material. However, PLA is relatively cost effective. Blending starch with PLA is one of the promising efforts because starch is a widely distributed and inexpensive product. PLA and starch were blended using a rheometer to form composites in this report. Glycerin was added into the blends to make the mixture molecular compatible and more homogeneous. The starch was crosslinked using epichlorohydrin to improve the compatibility of starch with PLA. Two series of composite were fabricated. One was PLA and the crosslinked starch containing 32 wt% glycerin. In this group, the crosslinking degree of the modified starch was varied. The second group was PLA and non-crosslinked starch with varied amount of glycerin added. Micro-structure of the blending composites was observed using a SEM to view the homogeneity of the mixture. The SEM pictures indicated that the compatibility of PLA and starch molecules was poor. The addition of glycerin can change the compatibility of PLA and starch. The higher the glycerin content in the composites, the better the compatibility between PLA and starch. Furthermore, when the starch was crosslinked by epichlorohydrin, the compatibility of PLA and starch can be greatly improved. The compatibility increases with the increase of crosslinking degree. This is due to the change of hydrophilicity of starch because the hydroxyl groups on the starch molecules were crosslinked into ether groups by the epichlorohydrin molecules.     

In-Process Measurements of Flow Characteristics of Wood Plastic Composites

The flow characteristics of polypropylene filled with high percentages of wood flour (50 and 70 wt%) are investigated at a feasible processing temperature (195 °C). Rotational rheometry in oscillatory mode in conjunction with the Cox–Merz rule is ineffective at this temperature due to insufficient linear viscoelastic region (LVR) size and ease of fibres degradation. An in-line rheometer, directly attached to a single screw extruder, is used to avoid these problems: this method allows measurements in real processing conditions with no LVR issues and with reduced degradation risks. The 70 wt% displays plug flow, thus it has been impossible to obtain the flow curve but only the slip velocity as a function of shear stress. The 50 wt% could be corrected for slip using the Mooney procedure. Comparing the flow curve of this material with the ones of the 30 wt% and the unfilled polypropylene matrix, a single master-curve can be obtained and modelled with a Carreau–Yasuda equation.     

Natural Weathering of Kenaf Bast Fibre-Filled Poly(Butylene Succinate) Composites: Effect of Fibre Loading and Compatibiliser Addition

Natural weathering was performed on poly(butylene succinate) (PBS) and its kenaf bast fibre (KBF) filled composites by exposing the specimens to a tropical climate for a period of 6 months (max–min temperature: 31.5–23.9 °C; relative humidity: 78.9%). The aim of this study was to investigate the effects of KBF loading and the addition of maleated PBS compatibiliser (PBSgMA) on the performance of the composites under natural weathering. As expected, the flexural properties of both the uncompatibilised and compatibilised composites dropped with increasing exposure time. The weathered specimens were also assessed by colour change analysis, FTIR spectroscopy analysis and SEM examination. The total colour change, ΔE _ab , of both the uncompatibilised and compatibilised composites increased with weathering time. FTIR spectroscopy analysis confirmed the presence of oxidation products such as hydroxyl, carbonyl and vinyl species in the weathered uncompatibilised and compatibilised composites. SEM examination revealed the presence of surface defects such as cracking, tiny holes and degraded fibre, which explain the poor performance of the composites upon weathering.     

曝气生物滤池效能关键影响因素研究进展

曝气生物滤池（BAF）是一种新型的生物氧化处理工艺,已被广泛应用于城市废水处理、中水回用及微污染源水的预处理。详细论述了目前国内外对BAF效能的关键影响因素,如填料、水力停留时间、进水底物、水温、曝气量与进水量比、反冲洗工艺、化学除磷药剂等的研究现状,并探讨了其今后的研究方向。     

Performance of Cow Dung Reinforced Biodegradable Poly(Lactic Acid) Biocomposites for Structural Applications

In this work, performance of cow dung (CD) reinforced poly(lactic acid) (PLA) biocomposites was investigated for the potential use in load bearing application. CD of average 4 mm size was blended with PLA at different CD ratios (0–50 wt%) and their effects on the biocomposite properties were studied. The results showed an improvement in the flexural properties, while the tensile and impact strength dropped by 20 and 28% with the addition of 50% CD. The decline in the tensile and impact strength was due to micro-cracking and voids formation at higher CD content. Also, the incorporation of CD slightly decreased the thermal stability of the biocomposite. However, dynamic mechanical properties of the biocomposites generally improved. SEM analysis of tensile and impact fractured surfaces indicated that the CD had a reasonable adhesion with matrix. Moreover, the SEM micrographs of soil burial studies showed an accelerated degradation of higher CD wt% biocomposites.     

Adsorption of Ammonium by Graphene Oxide-Based Composites Prepared by UV Irradiation and Using as Slow-Release Fertilizer

A novel sodium alginate-grafted poly(acrylic acid)/graphene oxide (NaAlg-g-PAA/GO) composite hydrogel was prepared via ultraviolet irradiation, and characterized by infrared spectroscopy spectrometer. X-ray diffraction, X-ray photoelectron spectroscopy and scanning electron microscopy. It was employed to adsorb NH₄⁺ from aqueous solution and used as slow-release nitrogen fertilizers (SNFs). Result indicated that the adsorption process for NH₄⁺ reached equilibrium within 50 min, with the adsorption capacity of 6.6 mmol g^?1 even if 30 wt% GO was incorporated. The results of adsorption kinetic and isotherm were well described by the pseudo-second-order and Freundlich model. The thermodynamics analysis showed the adsorption process was spontaneous. The study indicated excellent water-holding ratio of soil with 2 wt% SNFs was 81.2%, and nitrogen release was up to 55.1% within 40 days in soil. Overall, NaAlg-g-PAA/GO could be considered as an efficient adsorbent for the recovery of nitrogen with the agronomic reuse as a fertilizer.