Measurement of transferable chemical residue from nylon carpet using the California roller and a new mega-California roller

Human chemical exposures resulting from transfer of surface deposition on indoor nylon carpets may be estimated by measuring transferable residues (μ g chemical/cm² carpet). A weighted roller developed at California Department of Food and Agriculture (CDFA) has been extensively used to sample transferable residue for estimates of human exposure in risk characterization. A modified roller has been developed to evaluate the influence of pressure on transferable chemical residue since weight and force (or pressure, kg/m²) may vary person-to-person and activity-to-activity. A 30.5 cm diameter roller was used to apply 60 to 2100 kg/m² to bracket pressures exerted by humans on a flat nylon-carpeted surface. Measurements of transferable cyfluthrin residues were made after 1, 7, and 21 days. Total Soxhlet extractable cyfluthrin residues were relatively constant during the test period. Residue transferability decreased during the study period. Modest increases in the transferability of surface residues were observed over the broad range of pressures applied by the modified roller.     

Artificial sweat enhances dermal transfer of chlorpyrifos from treated nylon carpet fibers

The dermal transfer and absorption of 14C-ring-chlorpyrifos from nylon carpet fibers was measured in skin penetration-evaporation cells with excised pig skin. Prior to application, synthetic sweat was applied to skin in half of the cells. Radioactivity was measured in receptor fluid, dermis, epidermis, tape stripping samples, and vapor trap samples during a 24-h period. The sum of radiolabel recovered from the dermis and receptor fluid represented the absorbed dose. There was no significant difference (p > 0.05) in percutaneous absorption between cells that received the synthetic sweat application and "dry" cells (1.3 +/- 0.3% of applied dose). There was significantly more (p < 0.05) radiolabel recovered from tape stripping (5.4 +/- 2.1 vs. 2.8 +/- 0.6%) and in the epidermis (4.5 +/- 0.8 vs. 3.1 +/- 0.3%) from cells that received the synthetic sweat application, which indicated synthetic sweat facilitated transfer of chlorpyrifos from a treated substrate to the skin surface. The measured value for percutaneous absorption of chlorpyrifos agreed with the value predicted from an empirical model previously developed for nitro compound-containing soil.     

In situ fixation of metals in soils using bauxite residue: chemical assessment

Contamination of soils with heavy metals and metalloids is a widespread problem all over the world. Low cost, non-invasive, in situ technologies are required for remediation processes. We investigated the efficiency of a bauxite residue (red mud) to fix heavy metals in two soils, one contaminated by industrial activities (French soil), and one by sewage sludge applications (UK soil). This Fe-oxide rich material was compared with lime, or beringite, a modified aluminosilicate that has been used for in situ fixation processes. Four different crop species were successively grown in pots. Metal concentrations in the soil pore waters were analyzed during the growing cycles. At the end of the experiment fluxes of heavy metals were measured using a diffusive gradient in thin film technique (DGT). Furthermore, a sequential extraction procedure (SEP) and an acidification test were performed to investigate the mechanisms of metal fixation by different soil amendments. In both soils, the concentrations of metals in the soil pore water and metal fluxes were greatly decreased by the amendments. An application of 2% red mud performed as well as beringite applied at 5%. Increasing soil pH was a common mechanism of action for all the amendments. However, the red mud amendment shifted metals from the exchangeable to the Fe-oxide fraction, and decreased acid extractability of metals. The results suggest that specific chemisorption, and possibly metal diffusion into oxide particles could also be the mechanisms responsible for the fixation of metals by red mud.     

Copper and cadmium removal from synthetic industrial wastewater using chitosan and nylon 6

Purpose

Chitosan with nylon 6 membranes was evaluated as adsorbents to remove copper and cadmium ions from synthetic industrial wastewater.

Methods

Chitosan and nylon 6 with glutaraldehyde blend ratio with (1:1+Glu, 1:2+Glu, and 2:1+Glu) have been prepared and these were used as membranes to remove copper and cadmium ions from synthetic industrial wastewater. Characterization of the synthesized membrane has been done with FTIR, XRD, TGA/DTA, DSC, and SEM. Chemical parameters for quantities of adsorption of heavy metal contamination have been done and the kinetics of adsorption has also been carried out.

Results

The optimal pH for the removal of Cd(II) and Cu(II) using chitosan with nylon 6. Maximum removal of the metals was observed at pH 5 for both the metals. The effect of adsorbent dose also has a pronounced effect on the percentage of removal of the metals. Maximum removal of both the metals was observed at 5 g/100 ml of the adsorbent.

Conclusion

Copper and cadmium recovery is parallel at all time. The percentage of removal of copper increased with increase in the pH from 3 to 5. In the case of cadmium containing wastewater, the maximum removal of metal occurred at pH 5. The uptake amount of Cu²⁺ ions on chitosan increased rapidly with increasing contact time from 0 to 360 min and then reaches equilibrium after 360 min; the equilibrium constant for copper and cadmium ions is more or less the same for the adsorption reaction.     

Application of a Combined Measurement and Modeling Method to Quantify Windblown Dust Emissions from the Exposed Playa at Mono Lake,California

ABSTRACT

Particulate matter ≤10 μm (PM₁₀) emissions due to wind erosion can vary dramatically with changing surface conditions. Crust formation, mechanical disturbance, soil texture, moisture, and chemical content of the soil can affect the amount of dust emitted during a wind event. A refined method of quantifying windblown dust emissions was applied at Mono Lake, CA, to account for changing surface conditions. This method used a combination of real-time sand flux monitoring, ambient PM₁₀ monitoring, and dispersion modeling to estimate dust emissions and their downwind impact. The method identified periods with high emissions and periods when the surface was stable (no sand flux), even though winds may have been high. A network of 25 Cox sand catchers (CSCs) was used to measure the mass of saltating particles to estimate sand flux rates across a 2-km² area. Two electronic sensors (Sensits) were used to time-resolve the CSC sand mass to estimate hourly sand flux rates, and a perimeter tapered element oscillating microbalance (TEOM) monitor measured hourly PM₁₀ concentrations. Hourly sand flux rates were related by dispersion modeling to hourly PM₁₀ concentrations to back-calculate the ratio of vertical PM₁₀ flux to horizontal sand flux (K-factors). Geometric mean K-factor values (K _f) were found to change seasonally, ranging from 1.3 × 10^?5 to 5.1 × 10^?5 for sand flux measured at 15 cm above the surface (q ₁₅). Hourly PM₁₀ emissions, F, were calculated by applying seasonal K-factors to sand flux measurements (F?=?K _f ×?q ₁₅). The maximum hourly PM10 emission rate from the study area was 76 g/m²·hr (10-m wind speed?=?23.5 m/sec). Maximum daily PM₁₀ emissions were estimated at 450 g/m²·day, and annual emissions at 1095 g/m²·yr. Hourly PM₁₀ emissions were used by the U.S. Environmental Protection Agency (EPA) guideline AERMOD dispersion model to estimate downwind ambient impacts. Model predictions compared well with monitor concentrations, with hourly PM₁₀ ranging from 16 to over 60,000 μg/m³ (slope?=?0.89, R ²?=?0.77).

IMPLICATIONS Under a U.S. Environmental Protection Agency (EPA)-approved plan, the method described in this paper has been used since 2000 at Owens Lake, CA, to identify and successfully mitigate dust from over 100 km² of the dry lakebed. It continues to be used to monitor dust control compliance at Owens Lake. Scaled-down versions of the Owens Lake network can be implemented in other areas in a manner similar to the Mono Lake study. Once K-factors are established, low-cost CSC samplers (about $35 U.S.) may be used for periodic monitoring (e.g., daily, weekly, or monthly) to estimate PM₁₀ emissions or to evaluate dust control compliance.     

Influence of organic waste and residue mud additions on chemical,physical and microbial properties of bauxite residue sand

Background, aim and scope  

In an alumina refinery, bauxite ore is treated with sodium hydroxide at high temperatures and pressures and for every tonne of alumina produced, about 2 tonnes of alkaline, saline bauxite processing waste is also produced. At Alcoa, a dry stacking system of disposal is used, and it is the sand fraction of the processing waste that is rehabilitated. There is little information available regarding the most appropriate amendments to add to the processing sand to aid in revegetation. The purpose of this study was to investigate how the addition of organic wastes (biosolids and poultry manure), in the presence or absence of added residue mud, would affect the properties of the residue sand and its suitability for revegetation.     

Recycling lead from a zinc plant residue (ZPR) using brine leaching and cementation with aluminum powder

Environmental Science and Pollution Research - This research investigated the treatment process of an Iranian zinc plant residue for recycling lead utilizing brine leaching and cementation with...     

Emissions from carpet combustion in a pilot-scale rotary kiln: comparison with coal and particle-board combustion

The use of post-consumer carpet as a potential fuel substitute in cement kilns and other high-temperature processes is being considered to address the problem of huge volumes of carpet waste and the opportunity of waste-to-energy recovery. Carpet represents a high volume waste stream, provides high energy value, and contains other recoverable materials for the production of cement. This research studied the emission characteristics of burning 0.46-kg charges of chopped nylon carpet squares, pulverized coal, and particle-board pellets in a pilot-scale natural gas-fired rotary kiln. Carpet was tested with different amounts of water added. Emissions of oxygen, carbon dioxide, nitric oxide (NO), sulfur dioxide (SO2), carbon monoxide (CO), and total hydrocarbons and temperatures were continuously monitored. It was found that carpet burned faster and more completely than coal and particle board, with a rapid volatile release that resulted in large and variable transient emission peaks. NO emissions from carpet combustion ranged from 0.06 to 0.15 g/MJ and were inversely related to CO emissions. Carpet combustion yielded higher NO emissions than coal and particle-board combustion, consistent with its higher nitrogen content. SO2 emissions were highest for coal combustion, consistent with its higher sulfur content than carpet or particle board. Adding water to carpet slowed its burn time and reduced variability in the emission transients, reducing the CO peak but increasing NO emissions. Results of this study indicate that carpet waste can be used as an effective alternative fuel, with the caveats that it might be necessary to wet carpet or chop it finely to avoid excessive transient puff emissions due to its high volatility compared with other solid fuels, and that controlled mixing of combustion air might be used to control NO emissions from nylon carpet.     

Development of the crop residue and rangeland burning in the 2014 National Emissions Inventory using information from multiple sources

Biomass burning has been identified as an important contributor to the degradation of air quality because of its impact on ozone and particulate matter. One component of the biomass burning inventory, crop residue burning, has been poorly characterized in the National Emissions Inventory (NEI). In the 2011 NEI, wildland fires, prescribed fires, and crop residue burning collectively were the largest source of PM_2.5. This paper summarizes our 2014 NEI method to estimate crop residue burning emissions and grass/pasture burning emissions using remote sensing data and field information and literature-based, crop-specific emission factors. We focus on both the postharvest and pre-harvest burning that takes place with bluegrass, corn, cotton, rice, soybeans, sugarcane and wheat. Estimates for 2014 indicate that over the continental United States (CONUS), crop residue burning excluding all areas identified as Pasture/Grass, Grassland Herbaceous, and Pasture/Hay occurred over approximately 1.5 million acres of land and produced 19,600 short tons of PM_2.5. For areas identified as Pasture/Grass, Grassland Herbaceous, and Pasture/Hay, biomass burning emissions occurred over approximately 1.6 million acres of land and produced 30,000 short tons of PM_2.5. This estimate compares with the 2011 NEI and 2008 NEI as follows: 2008: 49,650 short tons and 2011: 141,180 short tons. Note that in the previous two NEIs rangeland burning was not well defined and so the comparison is not exact. The remote sensing data also provided verification of our existing diurnal profile for crop residue burning emissions used in chemical transport modeling. In addition, the entire database used to estimate this sector of emissions is available on EPA’s Clearinghouse for Inventories and Emission Factors (CHIEF, http://www3.epa.gov/ttn/chief/index.html).Implications: Estimates of crop residue burning and rangeland burning emissions can be improved by using satellite detections. Local information is helpful in distinguishing crop residue and rangeland burning from all other types of fires.     

Real-time measurements of the chemical composition of size-resolved particles during a Santa Ana wind episode,California USA

Size-resolved particle composition, mass and number concentrations, aerosol scattering coefficients, and prevailing meteorological conditions were measured at the Ellen Browning Scripps Memorial Pier located in La Jolla, California on 15 December 1998. Aerosol particles were sampled using a field transportable aerosol time-of-flight mass spectrometer, allowing for the continuous detection and characterization of single particles from a polydisperse sample. An extensive and rapid change in the chemical composition of aerosol particles with aerodynamic diameters between 1.0 and 2.5 μm has been observed during the onset of a Santa Ana Winds condition. Coincident with the observed change in meteorological conditions, a substantial decrease in sea salt particles corresponds to an increase in dust and carbon-containing particles. This paper examines observations of the rapid changes occurring in the chemical composition of single aerosol particles and demonstrates the new types of information that can be obtained by measuring single particle size and composition with high temporal resolution.     

废印制线路板真空热解渣分选与组成分析的研究

在自行设计制备的真空热解炉中进行了废印制线路板的热解实验,得到固体、液体和气体产物。着重研究了热解固体渣中金属铜和非金属玻璃纤维的物理分选、热解固体渣分析及有氧煅烧对玻璃纤维纯度的影响。结果表明,物理分选效率很高,金属铜的回收率和纯度接近100%;热解固体渣含30.35%的铜、56.21%的玻璃纤维和13.45%的炭黑;有氧煅烧去除炭黑可得到高纯度的玻璃纤维。     

Measurement of organic mass to organic carbon ratio in ambient aerosol samples using a gravimetric technique in combination with chemical analysis

Organic materials make up a significant fraction of ambient particulate mass. It is important to quantify their contributions to the total aerosol mass for the identification of aerosol sources and subsequently formulating effective control measures. The organic carbon (OC) mass can be determined by an aerosol carbon analyzer; however, there is no direct method for the determination of the mass of organic compounds, which also contain N, H, and O atoms in addition to C. The often-adopted approach is to estimate the organic mass (OM) from OC multiplying by a factor. However, this OC-to-OM multiplier was rarely measured for a lack of appropriate methods for OM. We report here a top-down approach to determine OM by coupling thermal gravimetric and chemical analyses. OM is taken to be the mass difference of a filter before and after heating at 550 °C in air for 4 h minus mass losses due to elemental carbon (EC), volatile inorganic compounds (e.g., NH₄NO₃), and loss of aerosol-associated water that arise from the heating treatment. The losses of EC and inorganic compounds are determined through chemical analysis of the filter before and after the heating treatment. We analyzed 37 ambient aerosol samples collected in Hong Kong during the winter of 2003, spring of 2004, and summer of 2005. A value of 2.1±0.3 was found to be the appropriate factor to convert OC to OM in these Hong Kong aerosol samples. If the dominant air mass is classified into two categories, then an OM-to-OC ratio of 2.2 was applicable to aerosols dominated by continent-originated air mass, and 1.9 was applicable to aerosols dominated by marine air mass.     

铬污染场地渣土混合物的化学还原修复

针对目前铬污染场地表层重污染铬渣混土难处理的问题,选用河南义马某铬盐厂铬渣堆场表层渣土混合物为研究对象,在分析其理化特性的基础上,研究CaS4、FeSO4·7H2O和葡萄糖3种还原药剂对Cr(VI) 的还原效率,通过改变药剂投加量、反应体系pH、反应时间等条件,优化修复工艺参数。结果表明,3种还原药剂对渣土混合物的最佳还原效率大小为CaS4(98.50%)>FeSO4·7H2O(72.21%)>葡萄糖(51.45%)。CaS4还原修复渣土混合物的最优工艺参数为：药剂投加量为还原反应理论当量的2倍,体系pH在3～9,反应时间0.5 h。     

污泥与餐厨垃圾联合厌氧发酵产氢余物产甲烷条件优化研究

研究了21、37和47 d产甲烷物料代替新鲜污泥接种于污泥与餐厨垃圾联合厌氧发酵产氢余物的厌氧发酵产甲烷情况,发现接种47 d产甲烷物料的消化系统在最佳接种量50%条件下的产甲烷效能显著优于接种新鲜污泥的消化系统,不仅提高了产甲烷率,还大大缩短了消化时间。并且3种消化系统产甲烷率和比产甲烷率均为47 d37 d21 d,分别为3.78、3.88、6.15 mL/g和0.172、0.277、0.559 mL/(g·d),完成产甲烷过程的消化时间为47 d37 d21 d。在一定的消化时间范围内,产甲烷菌被驯化时间越长,接种于产氢余物中的产甲烷效能越好。     

Measurement of trifluralin volatilization in the field: Relation to soil residue and effect of soil incorporation

Volatilization may represent a major dissipation pathway for pesticides applied to soils or crops. A field experiment (September, 2002), consisted in volatilization fluxes measurements during 6 days, covering the periods before and after soil incorporation carried out 24 h after trifluralin spraying on bare soil. Evolution of concentration in soil was measured during 101 days, together with soil physical and meteorological variables. Volatilization fluxes were very high immediately after application (1900 ng m(-2) s(-1)), decreased down to 100 ng m(-2) s(-1) in the following 24 h. Soil incorporation strongly abated trifluralin concentration in the air. 99% of the total volatilization losses recorded over the 6 days following application occurred before incorporation. Volatilization fluxes evidenced a diurnal cycle driven by environmental conditions. Soil trifluralin residues could still be quantified 101 days after application. Our results highlight the caution required when using soil degradation half-life values in the field for volatile compounds.     

Day-of-week patterns of particulate matter and its chemical components at selected sites in California

This paper analyzes day-of-week variations in concentrations of particulate matter (PM) in California. Because volatile organic compounds (VOCs) and oxides of nitrogen (NOx) are not only precursors of ozone (O3) but also of secondary PM, it is useful to know whether the variations by day of week in these precursors are also evident in PM data. Concentrations of PM < or = 10 microm (PM10) and < or = 2.5 microm in aerodynamic diameter (PM2.5) were analyzed. PM concentrations exhibit a general weekly pattern, with the maximum occurring late in the workweek and the minimum occurring on weekends (especially Sunday); however, this pattern does not prevail at all sites and areas. PM nitrate (NO3-) data from Size Selective Inlet (SSI) samplers in the South Coast Air Basin (SoCAB) tend to be somewhat lower on weekends compared with weekdays. During 1988-1991, the weekend average was lower than the weekday average at 8 of 13 locations, with an average decrease of 1%. During 1997-2000, the weekend average was lower than the weekday average at 10 of 13 locations, with an average decrease of 6%. The weekend averages are generally lower than weekday averages for sulfates, organic carbon, and elemental carbon. Because heavy-duty trucks typically represent a major source of elemental carbon, the weekend decrease in heavy-duty truck traffic may also result in a decrease in ambient elemental carbon concentrations.     

Observations and Model Simulations of Carbon Monoxide Emission Factors from a California Highway

ABSTRACT

A series of twelve intensively monitored 1-hr CO dispersion studies were conducted near Davis, CA, in winter 1996. The experimental equipment included twelve CO sampling ports at elevations up to 50 m, three sonic anemometers, a tethersonde station, aircraft measurements of wind and temperature profile aloft, and a variety of conventional meteorological equipment. The study was designed to explore the role of vehicular exhaust buoyancy during worst-case meteorological conditions, such as low winds oriented in near-parallel alignment with the road during a surface-based nocturnal inversion. From the study, field estimates of the CO emission factor (EF) from a California vehicle fleet were computed using two different methods. The analysis suggests that the CT-EMFAC/ EMFAC (EMission FACtor) models currently used to conduct federal conformity modeling significantly overpredict CO emissions for high-speed, free-flowing traffic on California highways.     

Observations and model simulations of carbon monoxide emission factors from a California highway

A series of twelve intensively monitored 1-hr CO dispersion studies were conducted near Davis, CA, in winter 1996. The experimental equipment included twelve CO sampling ports at elevations up to 50 m, three sonic anemometers, a tethersonde station, aircraft measurements of wind and temperature profile aloft, and a variety of conventional meteorological equipment. The study was designed to explore the role of vehicular exhaust buoyancy during worst-case meteorological conditions, such as low winds oriented in near-parallel alignment with the road during a surface-based nocturnal inversion. From the study, field estimates of the CO emission factor (EF) from a California vehicle fleet were computed using two different methods. The analysis suggests that the CT-EMFAC/EMFAC (EMission FACtor) models currently used to conduct federal conformity modeling significantly overpredict CO emissions for high-speed, free-flowing traffic on California highways.     

污泥与餐厨垃圾联合厌氧发酵产氢余物产甲烷过程底物指标变化

将污泥与餐厨垃圾联合厌氧发酵产氢余物进一步产甲烷,产甲烷量比污泥与餐厨垃圾单独或直接联合厌氧发酵产甲烷大。研究污泥与餐厨垃圾联合厌氧发酵产氢余物产甲烷过程中产甲烷量与底物指标变化的关系,实验结果表明,整个消化过程中,累积产甲烷量为613 L,最大产气速率和产甲烷速率分别为2.12 L/(kg·d)和1.46 L/(kg·d),最大甲烷含量为72.5 %,消化系统的pH在总挥发性脂肪酸(TVFA)以及氨氮、CO32-和HCO3-等碱度的共同作用下基本维持在适宜产甲烷的范围内,在不同的消化阶段,厌氧发酵产甲烷过程起主要作用的物质不同,先后顺序依次为糖类、蛋白质和TVFA,并且累积产甲烷量与COD、总糖、总蛋白质的显著相关性大小依次为:COD > 总糖 > 总蛋白质,COD去除率高达79.54 %。