Evaluation of Hook Handles in a Pulling Task

To evaluate the effect of handle design characteristics on subjective ratings and pulling forces, meat-hook handles with various handle shapes, sizes, and hook positions were tested in a pulling task. Finger and phalange force data measured by force sensitive resistors and subjective ratings of discomfort were also evaluated. Generally subjects preferred 37-mm double frustum, 30-mm oval handles followed by 30-mm double frustum handles, 37-mm oval, and 45-mm double frustum handles. In the analyses of total pulling force, 37- and 45-mm double frustum handles showed less required pulling force than the others. The averages of finger force contributions to the total pulling force were 27.2, 28.1, 23.9, and 20.8% in order from index to little fingers. The average of phalange force contributions were 28.8, 33.6, and 37.6% for the distal, middle, and proximal phalanges, respectively. The findings illustrate that the pulling finger forces and subjective discomfort ratings were related to the handle shape as well as handle size.     

非线性拉伸对甲烷-空气预混火焰燃烧特性的影响

使用定容燃烧弹与高速纹影照相系统研究了不同当量比下甲烷-空气预混气体的层流火焰燃烧特性。实验数据同时应用传统线性模型和非线性模型分析了不同当量比对球形扩展火焰的传播速率和马克斯坦长度的影响。结果显示:随着当量比的增加,层流燃烧速率先增大后减小,直到当量比为1.1时,火焰速率达到最大值。马克斯坦长度始终为正值,且随着当量比的增大而增大。在所有当量比条件下,线性和非线性方法计算的火焰速率大致相同,差值小于0.01 m/s;线性方法得到的马克斯坦长度均大于非线性模型计算的结果,并随着当量比的增大,两种方法得到的马克斯坦长度的差值更加显著。     

Lumbar Bone Mineral Density Phantomless Computed Tomography Measurements and Correlation with Age and Fracture Incidence

Objective: Low bone quality is a contributing factor to motor vehicle crash (MVC) injury. Quantification of occupant bone mineral density (BMD) is important from an injury causation standpoint. The first aim of this study was to validate a technique for measuring lumbar volumetric BMD (vBMD) from phantomless computed tomography (CT) scans. The second aim was to apply the validated phantomless technique to quantify lumbar vBMD in Crash Injury Research and Engineering Network (CIREN) occupants for correlation with age, fracture incidence, and osteopenia/osteoporosis diagnoses.

Methods: Quantitative CT (qCT) and dual-energy X-ray absorptiometry (DXA) were collected prospectively for 50 subjects and used to validate a technique to measure vBMD from 281 phantomless CT scans of CIREN occupants. Hounsfield unit (HU) measurements were collected from the L1–L5 vertebrae, right psoas major muscle, and anterior subcutaneous fat for all subjects and from 3 phantom ports with known mg/cc calcium hydroxyapatite values for the validation group. qCT calibration was accomplished using regressions between the phantom HU and mg/cc values to convert L1–L5 HU values to mg/cc. A phantomless calibration technique was developed where the fat and muscle HU values were linearly regressed against fat (?69 mg/cc) and muscle (77 mg/cc) to establish a conversion for L1–L5 HU measurements to mg/cc. vBMD calculated from qCT versus the phantomless method was compared for the 50 subjects to assess agreement and a mg/cc osteopenia threshold was established using DXA T-scores. CIREN HU measurements were converted to mg/cc using the phantomless technique and the mg/cc osteopenia threshold was used to compare vBMD to age, fracture incidence, and osteopenia comorbidity classifications in CIREN.

Results: Linear regression of lumbar vBMD derived from the qCT versus phantomless calibrations showed excellent agreement (R² = 0.87, P <.0001). A 145 mg/cc threshold for osteopenia was established (sensitivity = 1, specificity = 0.57) and 44 CIREN occupants had vBMD below this threshold. Of these 44 occupants, 64% were not classified as osteopenic in CIREN, but vBMD suggested undiagnosed osteopenia. Age was negatively correlated with vBMD in both sexes (P <.0001) and CIREN occupants with less than 145 mg/cc vBMD sustained an average 1.7 additional rib/sternum fractures (P =.036).

Conclusions: Because lumbar vBMD was estimated from phantomless CT scans with accuracy similar to qCT, the phantomless technique can be broadly applied to both prospectively and retrospectively assess patient bone quality for research and clinical studies related to MVCs, falls, and aging.     

Coefficient of friction,walking speed and cadence on slippery and dry surfaces: shoes with different groove depths

Objective. The present study aimed to determine the coefficient of friction (COF), walking speed (WS) and cadence while walking on slippery and dry surfaces using shoes with different sole groove depths to predict likelihood of fall. Background. Design of shoe sole groove is crucial to prevent slipping during walking. Methods. 22 healthy young men (mean age 24.5, body mass index 22.5) volunteered for this semi-experimental study. Six different conditions of the test (combination of three shoes and two surfaces) were defined and the condition was repeated three times. In total, 396 trials (22 subjects?×?3 groove depths?×?2 surfaces?×?3 times) were obtained for data analysis. COF was recorded by force platform at 1000?Hz and walking parameters recorded using 3D motion analysis with six infrared cameras at 200?Hz. Results. The highest COF was obtained from the deepest groove depth (5.0?mm) on both dry and slippery surfaces. The COF on slippery surfaces was significantly lower in comparison with dry surfaces. WS and cadence were not significantly different on dry and slippery surfaces. Conclusion. The deeper groove is better to prevent slipping because the COF increases by increasing the shoe sole groove depth. WS did not change on dry and slippery surfaces.     

Evaluation of design alternatives for sewing scissors with respect to hand performance,discomfort and usability

The effects of three re-designed models of sewing scissors on hand performance measures, discomfort and usability were investigated, and the results were compared with those of conventional scissors. Adjustments were made to the scissors handle with emphasis on more neutral wrist postures (bent handle - model A), correction of the thumb's position and movements (model B) and reducing hand/finger discomfort (model C) while working with the tool. The results showed some improvements in hand performance, muscular effort, usability and discomfort with model B compared to the conventional model. Better hand performance and usability and lower discomfort were recorded with model C compared to the conventional model. The results suggest that the correction of the thumb's position and movement (model B) or even reduced hand/finger discomfort (model C) are perhaps more important considerations in scissors design than improved wrist posture (model A) for improving users' performance and usability of the tool.     

Measures of health,fitness, and functional movement among firefighter recruits

Aim. The purpose of this study was to examine the associations between various health and fitness measures and Functional Movement Screen? (FMS?) scores among 78 firefighter recruits. Methods. Relationships between FMS? scores and age, body mass index (BMI), sit and reach (S&R) distance, estimated maximal aerobic capacity (V˙_O2max), estimated one-repetition maximum squat (1RM-Squat_max), and plank endurance (%Plank_max) were examined. Results. Total FMS? scores were significantly correlated with BMI (r?=??0.231, p?=?0.042), estimated 1RM-Squat_max (r?=?0.302, p?=?0.007), and %Plank_max (r?=?0.320, p?=?0.004). Multiple regression analyses indicated that this combination of predictors significantly predicted (F(3, 74)?=?5.043, p?=?0.003) Total FMS? score outcomes and accounted for 17% of the total variance (R²?=?0.170). In addition, logistic regression analyses indicated that estimated 1RM-Squat_max also significantly predicted (χ²?=?6.662, df?=?1, p?=?0.010) FMS? group membership (≤14 or ≥15). Conclusion. These results suggest that the health and fitness measures of obesity (BMI), bilateral lower extremity strength (estimated 1RM-Squat_max), and core muscular endurance (%Plank_max) are significantly associated with functional movement patterns among firefighter recruits. Consequently, injury prevention programs implemented among firefighter recruits should target these aspects of health and fitness.     

Passenger head kinematics in abrupt braking and lane change events

Abstract

Objective: A test track study was conducted to quantify patterns of adult front seat passenger head motion during abrupt vehicle maneuvers.

Method: Eighty-seven men and women with a wide range of body sizes and ages participated in data collection on a closed test track in a passenger sedan under manual control by a test driver. Because a primary goal of the study was to gather “unaware” data, the participants were instructed that the study was concerned with vehicle dynamics and they were required to read from a questionnaire taped to the top of their thighs as the drive began. The first event was a hard brake (approximately 1 g) to a stop from 35?mph (56 kph). Within the space of approximately 5?min the participants also experienced an aggressive lane change, a sharp right turn with simultaneous hard braking, and a second hard braking event. A Microsoft Kinect v2 sensor was positioned to view the area around the front passenger seat. Head location was tracked using the Kinect data with a novel methodology that fit 3D head scan data to the depth data acquired in the vehicle.

Result: The mean (standard deviation) forward excursion of the estimated head center of gravity (CG) location in the first braking event was 135 (62) mm. The forward head CG excursion in the second braking event of 115 (51) mm was significantly less than that in the first, but the difference was small relative to the within-condition variance. Head excursion on the second braking trial was less than that on the first trial for 69% of participants. The mean maximum inboard head excursion in lane-change maneuvers was 118 (40) mm. Forward head excursions in braking were significantly smaller for older passengers and those with higher body mass index, but the combined factors accounted for less than 25% of the variance. Inboard head excursion in the lane-change event was significantly related to stature, but only about 7% of variance was related to body size. Head excursions for men and women did not differ significantly after accounting for body size.

Discussion: This is the first quantitative occupant dynamics study to use a large, diverse sample of passengers, enabling the exploration of the effects of covariates such as age and body size.

Conclusions: The data demonstrate that a relatively large range of head positions can be expected to result from abrupt vehicle maneuvers. The data do not support simple scaling of excursions based on body size.     

Effect of occupational health nursing practice on musculoskeletal pains among hospital nursing staff in South Korea

Objective. The purpose of this study was to identify whether occupational health nursing variables serve as the contributing factors to musculoskeletal pains (MSP). Methods. A self-administered questionnaire composed of demographic characteristics, the practice of occupational health nursing and information regarding MSP was designed based on in-depth interviews with eight nurses. This study included 226 hospital nursing staff who worked at three university hospitals located in Seoul, South Korea. Statistical analysis was performed by using SPSS and AMOS 19.0. Results. Shoulder and neck pains occurred when subjects worked more than 46?h/week. Subjects who performed ‘work-time adjustment’ had lesser chance of having shoulder, leg/foot and wrist/finger pains. Overtime work hours showed an indirect effect on multiple sites of MSP by mediator variable, which was ‘work-time adjustment’. Organized night duty days eventually decreased multiple sites of MSP. Conclusion. Administration strategies for nurses to adjust work-time within 46?h/week should be considered.     

Experimental study on electrostatic charging of polymer powders in mixing processes

Powder mixing is often carried out in the chemical and pharmaceutical industries. Electrostatic charges generated on polymer powders during mixing may lead to electrostatic problems due to the poor conductivity of those powders. In this study, we investigated the electrostatic charges, surface potential, and apparent volume resistivity of sample powders using a simple mixing device utilizing the Faraday cup method. To neutralize the charged powders, we also applied an AC-type ionizer in the mixing study. A commercial polyethylene powder with a mean particle size of 585 μm was tested in this experiment. The charge-to-mass ratios at the end of 600 s of mixing were ?0.075 nC/g at 295 rpm agitation speed, ?0.21 nC/g at 495 rpm, and ?0.31 nC/g at 660 rpm, high enough to cause electrostatic agglomeration and adhesion. The electric fields based on the surface potential on the powders were several hundreds of V/cm, too small to give rise to brush discharge. The apparent volume resistivity of powders estimated by a simple measurement system is 1.0 × 10¹⁶ Ωm, in reasonable agreement with that acquired by the conventional test cell method (5.9 × 10¹⁵ Ωm). The charging level on the polymer powders was reduced with an AC-ionizer.     

工作场所手传振动的测量与评估——以割草机和绿篱机为例

根据ISO 5349:2001规定，将三轴加速度传感器安装在割草机和绿篱机的手柄上，通过振动分析仪AWA 6258测量割草机和绿篱机的频率计权振动总值，以进行手传振动的危害评估。结果表明:割草机和绿篱机的日振动暴露量A(8)值均超过了我国标准规定的日暴露振动限值3.5 m/s2，预计分别经过1.8～8.5 a和1.9～5.2 a后，暴露于割草和修枝工种人群的10%以上将出现振动性白指，为了有效降低或避免手臂振动病的发生，该行业的作业人员每日接触振动的时间应该控制在2.6 h以内。     

Provisional drivers' perceptions of the impact of displaying P plates

Objective: P plates (or decals) identify a driver's license status to other road users. They are a compulsory part of the graduated driver licensing system in Queensland, Australia, for drivers on a P1 (provisional 1) or P2 (provisional 2) license. This study explored the perceptions of young drivers regarding the display of P plates (decals) in Queensland, Australia.

Methods: In this study, 226 young drivers with a provisional (intermediate/restricted) license completed a 30-min online survey between October 2013 and June 2014. t Tests were used to compare the opinions of people who displayed their plates nearly always with those who displayed them less frequently.

Results: Participants approved of the requirement to display P plates with 69% of those on a P1 license and 79% on a P2 license supporting the condition to display P1 (red) plates. Participants on a P1 license (62%) and a P2 license (68%) also approved the requirement to display P2 (green) plates. However, young drivers also perceived that the display of P plates (measured from 1 = never to 5 = nearly all the time) enabled newly licensed drivers to be targeted by police and other drivers (those who do not always display P plates: M = 3.72, SD = 0.94; those who nearly always display P plates: M = 3.43, SD = 1.09).

Conclusions: The study findings suggest that participants who nearly always display their P plates are more likely to report that having to display their plates resulted in them driving more carefully.     

重特大事故的离散幂律分布——以煤矿事故为例

研究近年来我国每起煤矿重大和特别重大事故死亡人数统计数据,建立其概率分布模型。基于极大似然法和柯尔莫哥洛夫一斯米尔诺夫检验方法（K-S方法）估计我国煤矿重大和特别重大事故离散幂律分布的参数,并采用MonteCarlo方法随机生成大量的检验样本,对其进行K-S方法拟合优度检验。结果表明在统计学意义上我国煤矿重大和特别重大事故死亡人数比高斯分布的值大得多,服从标度指数为2．72的离散幂律分布。     

Anthropometric hand dimensions in a population of Iranian male workers in 2012

Background. The mismatch between the hand size of workers and the size of industrial instruments is a growing concern; it can lead to various musculoskeletal complications. Currently, there are few reliable studies available to address this concern in Iran. This study was conducted to measure 30 upper-extremity parameters in a group of Iranian industrial workers. Methods. This study is a cross-sectional study on 529 workers. The study population was randomly selected from male Iranian industrial workers who were referred to the Yazd hospital occupational medicine clinic for surveillance evaluations. Results. The M (SD) age of the participants was 30.13 (8.29) years. Statistical analysis was performed using the mean, standard deviation and 5th, 50th and 90th percentiles for each measured hand dimension. A considerable number of dimensions were significantly different between the measurements of right and left hands in each examinee. The results showed significant differences between Iranian hand size and that of other populations. Conclusion. This study provided a valuable databank of hand dimensions in a population of Iranian male workers. These data can be used by manufacturers in designing high-quality hand-tools and industrial gloves, taking into consideration Iranian worker characteristics.     

Comparison of Canadian firefighters and healthy controls based on submaximal fitness testing and strength considering age and gender

Introduction. Few studies have addressed whether firefighters are fitter than the general population and possess sufficient levels of aerobic capacity and muscle strength to perform on-duty tasks in a safe and efficient manner, considering age and gender. We aimed to evaluate the fitness levels of Hamilton firefighters, and to determine the effects of age and gender. Methods. In total, 89 participants were recruited. The modified Canadian aerobic fitness test was used to determine participants’ estimated maximal oxygen consumption (V_O2max) levels. For upper and lower body strength levels, a calibrated J-Tech hand-held dynamometer and a National Institute for Occupational Safety and Health (NIOSH) lifting device was used respectively. Results. Firefighters’ mean (SD) V_O2max level was 40.30?±?6.25?ml·kg^?1·min^?1. Age proved to have a statistically significant impact on V_O2max (p?<?0.001). Gender displayed statistically significant effects on strength levels. Firefighters’ age was the only statistically significant independent variable, and accounted for 61.00% of the variance in firefighters’ aerobic capacity levels. Conclusions. Firefighters possessed somewhat similar aerobic capacities but much higher levels of body strength when compared with the general population. With age, firefighters’ aerobic capacities decreased; however, their upper and lower body strength levels remained the same.     

Can new passenger cars reduce pedestrian lower extremity injury? A review of geometrical changes of front-end design before and after regulatory efforts

Objective: Pedestrian lower extremity represents the most frequently injured body region in car-to-pedestrian accidents. The European Directive concerning pedestrian safety was established in 2003 for evaluating pedestrian protection performance of car models. However, design changes have not been quantified since then. The goal of this study was to investigate front-end profiles of representative passenger car models and the potential influence on pedestrian lower extremity injury risk.

Methods: The front-end styling of sedans and sport utility vehicles (SUV) released from 2008 to 2011 was characterized by the geometrical parameters related to pedestrian safety and compared to representative car models before 2003. The influence of geometrical design change on the resultant risk of injury to pedestrian lower extremity—that is, knee ligament rupture and long bone fracture—was estimated by a previously developed assessment tool assuming identical structural stiffness. Based on response surface generated from simulation results of a human body model (HBM), the tool provided kinematic and kinetic responses of pedestrian lower extremity resulted from a given car's front-end design.

Results: Newer passenger cars exhibited a “flatter” front-end design. The median value of the sedan models provided 87.5 mm less bottom depth, and the SUV models exhibited 94.7 mm less bottom depth. In the lateral impact configuration similar to that in the regulatory test methods, these geometrical changes tend to reduce the injury risk of human knee ligament rupture by 36.6 and 39.6% based on computational approximation. The geometrical changes did not significantly influence the long bone fracture risk.

Conclusions: The present study reviewed the geometrical changes in car front-ends along with regulatory concerns regarding pedestrian safety. A preliminary quantitative benefit of the lower extremity injury reduction was estimated based on these geometrical features. Further investigation is recommended on the structural changes and inclusion of more accident scenarios.     

A study of the workload of underground trammers in the Ranigang coal field area of West Bengal, India.

Thirty healthy trammers were examined in underground haulage mines during their normal activity. Physiological strain in terms of heart rate (HR) varied between 101.6 and 104.7 beats/min with mean net cardiac cost of 33.06 and 34.06 beats/min for younger and older groups respectively. The average relative cardiac cost was lower for younger subjects than for older ones. Oxygen consumption (VO2) was measured with an Oxylog-II machine (UK); subsequently values were estimated. Maximum aerobic capacity was estimated with an indirect method following a standard step test protocol. The responses revealed that the average VO2 during the activity was 0.75 and 0.8 L/min, which corresponded to energy expenditure (EE) of 3.8 and 3.97 Kcal/min for younger and older subjects respectively. The workload in terms of HR and EE was moderate, whereas the aerobic strain experienced by aged workers was above the acceptable level.     

A ventilation cooling shirt worn during office work in a hot climate: cool or not?

The aim of the study was to identify whether a ventilation cooling shirt was effective in reducing heat strain in a hot climate. Eight female volunteers were exposed to heat (38?°C, 45% relative humidity) for 2?h with simulated office work. In the first hour they were in normal summer clothes (total thermal insulation 0.8?clo); in the second hour a ventilation cooling shirt was worn on top. After the shirt was introduced for 1?h, the skin temperatures at the scapula and the chest were significantly reduced (p?<?0.05). The mean skin and core temperatures were not reduced. The subjects felt cooler and more comfortable by wearing the shirt, but the cooling effect was most conspicuous only during the initial 10?min. The cooling efficiency of the ventilation shirt was not very effective under the low physical activity in this hot climate.     

Driving performance comparing older versus younger drivers

Objectives: A cross-sectional study was conducted at the Touro University California campus to compare differences in reaction times and driving performance of younger adult drivers (18–40 years) and older adult drivers (60 years and older). Each test group consisted of 38 participants.

Methods: A Simple Visual Reaction Test (SVRT) tool was used to measure reaction times. The STISIM Drive M100 driving simulator was used to assess driving parameters. Driving performance parameters included mean lane position, standard deviation of mean lane position measured, mean speed, standard deviation of mean speed, car-following delay, car-following modulus, car-following coherence, off-road accidents, collisions, pedestrians hit, and traffic light tickets.

Results: Compared to younger participants, older drivers experienced significantly slower reaction times (510.0 ± 208.8 vs. 372.4 ± 96.1 ms, P =.0004), had more collisions (0.18 ± 0.39 vs. none, P =.0044), drove slower (44.6 ± 6.6 vs. 54.9 ± 11.7 mph, P <.0001), deviated less in speed (12.6 ± 4.3 vs. 16.8 ± 6.3, P =.0011), and were less able to maintain a constant distance behind a pace car (0.42 ± 0.23 vs. 0.59 ± 0.24; P =.0025).

Conclusions: Differences exist in driving patterns of older and younger drivers as measured by reaction times and driving simulator outcomes. These results are the first to compare these 2 specific adult age groups' driving performance as measured by a standardized driving simulator scenario. Identifying these differences is essential in addressing them and preventing future traffic injuries.