The use of footwear insulation values measured on a thermal foot model.

The use of physiological data from human tests in modelling should consider background data, such as activity, environmental factors and clothing insulation on the whole body. The present paper focuses on local thermal comfort of feet with special attention on the effects of physical changes of footwear thermal properties. An alternative test method is available for footwear thermal testing besides the standard method. The possibility to use insulation values acquired on a thermal foot model in practice is shown here. The paper describes the correlation between cold and pain sensations, and foot skin temperatures of the subjects and relates these to insulation measured on a thermal foot model. Recommendations are made for footwear choice according to environmental temperature.     

Determination of Heat Loss from the Feet and Insulation of the Footwear

This study compared the methods of determining footwear insulation on human participants and a thermal foot model. Another purpose was to find the minimal number of measurement points on the human foot that is needed for insulation calculation. A bare foot was tested at 3 ambient temperatures on 6 participants. Three types of footwear were tested on 2 participants. The mean insulation for a bare foot obtained on the participant and model were similar. The insulation of warm footwear measured by the 2 methods was also similar. For thin footwear the insulation values from the participants were higher than those from the thermal model. The differences could be related to undefined physiological factors. Two points on the foot can be enough to measure the insulation of footwear on human participants (r = .98). However, due to the big individual differences of humans, and good repeatability and simplicity of thermal foot method, the latter should be preferred for testing.     

Parallel and Serial Methods of Calculating Thermal Insulation in European Manikin Standards

Abstract

Standard No. EN 15831:2004 provides 2 methods of calculating insulation: parallel and serial. The parallel method is similar to the global one defined in Standard No. ISO 9920:2007. Standards No. EN 342:2004, EN 14058:2004 and EN 13537:2002 refer to the methods defined in Standard No. EN ISO 15831:2004 for testing cold protective clothing or equipment. However, it is necessary to consider several issues, e.g., referring to measuring human subjects, when using the serial method. With one zone, there is no serial-parallel issue as the results are the same, while more zones increase the difference in insulation value between the methods. If insulation is evenly distributed, differences between the serial and parallel method are relatively small and proportional. However, with more insulation layers overlapping in heavy cold protective ensembles, the serial method produces higher insulation values than the parallel one and human studies. Therefore, the parallel method is recommended for standard testing.     

Parallel and serial methods of calculating thermal insulation in European manikin standards

Standard No. EN 15831:2004 provides 2 methods of calculating insulation: parallel and serial. The parallel method is similar to the global one defined in Standard No. ISO 9920:2007. Standards No. EN 342:2004, EN 14058:2004 and EN 13537:2002 refer to the methods defined in Standard No. EN ISO 15831:2004 for testing cold protective clothing or equipment. However, it is necessary to consider several issues, e.g., referring to measuring human subjects, when using the serial method. With one zone, there is no serial-parallel issue as the results are the same, while more zones increase the difference in insulation value between the methods. If insulation is evenly distributed, differences between the serial and parallel method are relatively small and proportional. However, with more insulation layers overlapping in heavy cold protective ensembles, the serial method produces higher insulation values than the parallel one and human studies. Therefore, the parallel method is recommended for standard testing.     

Testing Sleeping Bags According to EN 13537:2002: Details That Make the Difference

The European Standard on sleeping bag requirements (EN 13537:2002) describes a procedure to determine environmental temperature limits for safe usage of sleeping bags regarding their thermal insulation. However, there are several possible sources of error related to this procedure. The main aim of this work was to determine the influence of the various measuring parameters on the acuity of the respective parameters in order to judge the requirements. The results indicated that air velocity, mattress insulation and time between unpacking the bag and measurement had a significant impact on the result, with a difference of up to 5–15% in thermal insulation between minimum and maximum allowable parameter levels. On the other hand, manikin weight, thickness of the artificial ground and presence of a face mask were found to have a negligible influence. The article also discusses more general aspects of the standard including the calculation methods used.     

Effect of Sweating on Insulation of Footwear

The study aimed to find out the influence of sweating on footwear insulation with a thermal foot model. Simultaneously, the influence of applied weight (35 kg), sock, and steel toe cap were studied. Water to 3 sweat glands was supplied with a pump at the rate of 10 g/hr in total. Four models of boots with steel toe caps were tested. The same models were manufactured also without steel toe. Sweating reduced footwear insulation 19–25% (30–37% in toes). During static conditions, only a minimal amount of sweat evaporated from boots. Weight affected sole insulation: Reduction depended on compressibility of sole material. The influence of steel toe varied with insulation. The method of thermal foot model appears to be a practical tool for footwear evaluation.     

Safe storage of selected fuels with regard to their tendency to spontaneous combustion

European standard EN 15188 is dedicated to the assessment of the tendency of solid flammable substances to spontaneous combustion. Fossil fuels and biofuels that substitute them are a frequent reason of fires caused by spontaneous combustion. Even though having different properties, both types of fuels can be assessed according to this standard by the method of the determination of the dependency of self-ignition temperature against the ratio of volume to surface area of geometrically exactly defined solid body, or based on the theory of thermal explosion according to Frank-Kamenetskii. The comparison of calculated values confirmed the agreement of both methods results, and the tendency of fuels to spontaneous combustion can be assessed by them.     

鞋类保暖性能研究

本文采用鞋类保暖性能的测试方法,测定不同帮面材料、不同鞋底材料对鞋类保暖性能的影响,对于不同的测试对象探索相同环境下的测试结果,从而为企业生产提供一定的科学指导。     

Calculation of Clothing Insulation by Serial and Parallel Methods: Effects on Clothing Choice by IREQ and Thermal Responses in the Cold

Cold protective clothing was studied in 2 European Union projects. The objectives were (a) to examine different insulation calculation methods as measured on a manikin (serial or parallel), for the prediction of cold stress (IREQ); (b) to consider the effects of cold protective clothing on metabolic rate; (c) to evaluate the movement and wind correction of clothing insulation values.

Tests were carried out on 8 subjects. The results showed the possibility of incorporating the effect of increases in metabolic rate values due to thick cold protective clothing into the IREQ model. Using the higher thermal insulation value from the serial method in the IREQ prediction, would lead to unacceptable cooling of the users. Thus, only the parallel insulation calculation method in EN 342:2004 should be used. The wind and motion correction equation (No. 2) gave realistic values for total resultant insulation; dynamic testing according to EN 342:2004 may be omitted.     

Calculation of clothing insulation by serial and parallel methods: effects on clothing choice by IREQ and thermal responses in the cold.

Cold protective clothing was studied in 2 European Union projects. The objectives were (a) to examine different insulation calculation methods as measured on a manikin (serial or parallel), for the prediction of cold stress (IREQ); (b) to consider the effects of cold protective clothing on metabolic rate; (c) to evaluate the movement and wind correction of clothing insulation values. Tests were carried out on 8 subjects. The results showed the possibility of incorporating the effect of increases in metabolic rate values due to thick cold protective clothing into the IREQ model. Using the higher thermal insulation value from the serial method in the IREQ prediction, would lead to unacceptable cooling of the users. Thus, only the parallel insulation calculation method in EN 342:2004 should be used. The wind and motion correction equation (No. 2) gave realistic values for total resultant insulation; dynamic testing according to EN 342:2004 may be omitted.     

BS EN ISO 20345：2011《个体防护装备安全鞋》标准的解析和建议

本文通过对最新的BS EN ISO 20345：2011《个体防护装备安全鞋》标准的列表介绍和概括性分析,找出了新标准检测项目仍存在的遗留问题和未考虑到的缺陷以及需要界定的术语,并提出了今后标准的再修订意见。此再修订意见的给出,为推动今后与安全鞋标准BS EN ISO 20345：2011属于同一体系的我国GB 21148-2007《个体防护装备安全鞋》标准修订提供参考意见。     

A case study: An explosion in a milk spray dryer,CAPSA, NW Spain

European Standard EN 14491 (2006): “Dust explosion venting protective systems”, based on German Standard VDI 3673 (2002): “Pressure venting of dust explosions”, Verein Deustcher Ingenieure, specifies the basic design requirements for the selection of dust explosion venting protection systems.In this study an investigation into the efficiency of venting surfaces in accordance with Standard EN 14491 has been undertaken to check the validation of the same. Thus, the application of the standard to an actual case of an explosion in a milk spray dryer has been studied, taking into consideration the explosive characteristics of products treated in this type of installation and their venting requirements.The results obtained indicate that, in specific situations – such as the effects of turbulence, particularly in the cone, or dust layer self-ignition – the European Standard could underestimate the venting surface requirements needed to alleviate possible excess internal pressure in order to avoid injury or structural damage to spray dryers.     

Assessing the performance of motorcyclists’ impact protectors in simulated ATD knee and shoulder impacts

Objective: Fractures are a common injury among motorcycle riders and can have serious health implications. Impact protection (IP) has been designed to help prevent fractures, yet there are conflicting opinions as to whether this IP does in fact help prevent fractures in real-world crashes. This work aimed to (1) use simulated dummy impacts to examine whether existing types of IP could reduce the force transferred to the underlying bone to below fracture tolerance levels and (2) investigate whether current European Standard (EN 1621-1) test procedures for impact protectors designed for motorcyclists are sufficient to ensure fracture protection.

Method: Twenty-three shoulder and 7 knee IP specimens were tested using a 23-kg impactor contacting axially along the clavicle and femur of an anthropomorphic test device (ATD) at an energy level corresponding to the fracture tolerance of these bones. Sixteen IP specimens were the same as those worn by motorcycle riders involved in crashes where injury outcome was known (knee: n?=?3; shoulder: n?=?13) and the IP had been previously tested to EN 1621-1. Other IP tested represented a wide range of IP available for purchase at a motorcycle accessory store. Double and triple layers of IP were also tested. Energy attenuated during the dummy impacts was compared to energy attenuated when tested to EN 1621-1.

Results: Of the 23 shoulder IP tested, the average percentage reduction of transferred force to the shoulder from the baseline test was 7.6?±?4.8%. The percentage reduction of transferred force to the knee from the baseline was 43.9?±?7.5%. The entire group of knee IP tested reduced the transferred force to the knee to below the 10-kN injury threshold for the femur. There was a positive but nonsignificant correlation between the ATD test and the EN 1621-1 impact test performance, suggesting that the European standard test method likely provides a good indication of IP performance. However, given the low correlation coefficient, the relationship between IP performance in the European standard test method and injury protection remains unclear.

Conclusion: Though the energy attenuation test method in the European standard may be an appropriate approach, distinct differences in injury protection performance observed between knee and shoulder IP indicate that there may be a need for different performance criteria for IP designated to protect different body regions.     

防化学品鞋国家标准的研究

防化学品鞋在由各类化学品引起的工伤事故中对于预防足部伤害起到非常重要的作用。文章对国内外防化学品鞋相关标准的国内外情况、技术内容进行了分析与研究,以国外先进标准为依据对我国防化学品鞋标准的技术内容进行规定,以统一产品技术要求,完善足部防护标准体系,保障人身健康安全。     

高温防护鞋检测装置研制

高温防护鞋检测装置由温度传感器、智能电脑温控仪、鞋底隔热性能试验箱和外底耐高温性能试验台四部分组成。它具有测量范围宽、测量精度高、抗干扰能力强、操作方便等特点，完全满足LD32-1992《高温防护鞋》标准规定的试验方法要求。     

Dynamic Strength Tests for Low Elongation Lanyards

Lanyards are still important and common components of personal systems protecting against falls from a height. Experience with dynamic strength tests of lanyards indicates that test methods based on EN and ISO standards do not make objective assessment possible. This paper presents the results of theoretical and laboratory investigations of the performance of adjustable lanyards during fall arrest. The obtained results indicate that methods of testing and assessment based on those standards demonstrate considerable shortcomings when applied to low elongation lanyards. The assumptions for improved requirements and test methods of lanyards made of e.g., steel wire and aramid ropes are also presented.     

Recent development of standardization of testing methods for dust explosion in Japan

The Dust Explosion Committee of the Association of Powder Process Industry and Engineering (APPIE) of Japan has acted to establish the standard for the member of the Association. Two testing methods have been authorized by the Association. The methods are established to evaluate sensitivity and severity for dust explosion.The ignition sensitivity is evaluated by the minimum explosive dust cloud concentration. Tapping sieve equipment and a strictly-specified Hartmann-type explosion tube have been selected as the testing apparatus. The tapping sieve equipment is applied to measure the minimum explosive concentration by forming a dust cloud supplied from a sieve on the top of the explosion chamber. The Hartmann-type tube is used to investigate roughly whether the test powder is explosive or not. A lot of explosion tests had been carried out to standardize the equipment and evaluate the sensitivity. This APPIE standard is being revised.Along with the ISO standard for explosion severity, Research Institute of Industrial Safety, the Ministry of Labour published a Guide to Test Method for Explosion Pressure and Rate of Pressure Rise for Combustible Dusts in 1994. Based on this Guide, The APPIE Committee has made the draft for the member.These standards and drafts are aimed to be the Japanese Industrial Standard (JIS). No other similar standard exists in Japan. In the present paper, technical data and explosion statistics which are the background of the APPIE standard for the ignition sensitivity are to be described.     

Measurement of charge transfer during filling and emptying FIBC

Filling and emptying normal FIBC (flexible intermediate bulk containers) in hazardous areas represents a high electrostatic ignition hazard. Manufacturers of FIBC have therefore designed different measures to reduce the ignition risks from static electricity. Depending on the measures applied FIBC are categorized into types A, B, C and D. End of 2005 a new international standard for testing type D FIBC has been published. Type D FIBC have now to be certified according to this standard. Since this standard requires comprehensive ignition testing on a test rig especially designed for this purpose, industry is looking for a simpler test method, which can be used for the development of new FIBC fabric and in production quality control. In the present paper it is attempted to apply the method of charge transfer measurement to assess the ignition probability of static discharged from FIBC during filling and emptying and to correlate the results with the ignition tests performed on the standard test rig.     

Dynamic strength tests for low elongation lanyards.

Lanyards are still important and common components of personal systems protecting against falls from a height. Experience with dynamic strength tests of lanyards indicates that test methods based on EN and ISO standards do not make objective assessment possible. This paper presents the results of theoretical and laboratory investigations of the performance of adjustable lanyards during fall arrest. The obtained results indicate that methods of testing and assessment based on those standards demonstrate considerable shortcomings when applied to low elongation lanyards. The assumptions for improved requirements and test methods of lanyards made of, e.g., steel wire and aramid ropes are also presented.     

Determination and assessment of the characteristic values for the evaluation of the thermal safety of chemical processes

Experience gained in the chemical industry in testing and assessing the thermal safety of chemical processes is published in this paper. Isothermal and adiabatic tests, which are the most important methods for both small and large quantities, are described and discussed. Methods for testing the thermal hazards of primary or desired reactions are also included, e.g. reaction calorimetry, adiabatic methods, investigations using a sampling method. More important are the criteria for assessing the test results. On the basis of energies produced by primary and secondary reactions and the temperature ranges within which they take place, thermal hazards can be predicted. If the rules for the safe design of batch and semi-batch reactions are observed, it is possible to control the thermal behaviour of reactions.