Effects of Fuel Type,Driving Cycle,and Emission Status on In-Use Vehicle Exhaust Reactivity

ABSTRACT

The introduction of reformulated gasolines significantly reduced exhaust hydrocarbon (HC) mass emissions, but few data are available concerning how these new fuels affect exhaust reactivity. Similarly, while it is well established that high-emitting vehicles contribute a significant portion of total mobile source HC mass emissions, it is also important to evaluate the exhaust reactivity from these vehicles. The objective of this study was to evaluate the relative influence on in-use vehicle exhaust reactivity of three critical factors: fuel, driving cycle, and vehicle emission status. Nineteen in-use vehicles were tested with seven randomly assigned fuel types and two driving cycles: the Federal Test Procedure (FTP) and the Unified Cycle (UC). Total exhaust reactivity was not statistically different between the FTP and UC cycles but was significantly affected by fuel type. On average, the exhaust reactivity for California Phase 2 fuel was the lowest (16 % below the highest fuel type) among the seven fuels tested for cold start emissions. The average exhaust reactivity for high-emitting vehicles was significantly higher for hot stabilized (11%) and hot start (15%) emissions than for low-emitting vehicles. The exhaust reactivities for the FTP and UC cycles for light-end HCs and carbonyls were significantly different for the hot stabilized mode. There was a significant fuel effect on the mean specific reactivity (SR) for the mid-range HCs, but not for light-end HCs or carbonyls, while vehicle emission status affected the mean SR for all three HC compound classes.     

VOC composition and ozone-forming potential of the exhaust gas of in-use motorcycles

The emission profile of volatile organic compounds (VOC) and the ozone-forming potential (OP) of the exhaust gas of six in-use motorcycles (four 4-stroke- and two 2-stroke-engines) were determined. The motorcycles were tested on a chassis dynamometer in a real-world driving cycle. The analysis involved the C2–C12-hydrocarbons as well as the aldehydes and ketones. Additionally, the regulated THC and NO_x emissions were measured according to the test procedure for type approval (ECE 40). Two vehicles did not fulfil the THC emission standard, whereas all vehicles met the requirements for NO_x emission. The aromatic fuel components toluene and xylene, and the combustion products ethene and propene contributed most to the OP of the VOC emission. The highest OP was found with the 2-stroke engines. The VOC profile of the emissions varied with vehicle and driving conditions. The reactivity of the exhaust gas, defined as gram ozone per gram of non-methane organic gases (NMOG), increased with vehicle speed.     

Modeling and direct sensitivity analysis of biogenic emissions impacts on regional ozone formation in the Mexico-U.S. border area

A spatially and temporally resolved biogenic hydrocarbon and nitrogen oxides (NOx) emissions inventory has been developed for a region along the Mexico-U.S. border area. Average daily biogenic non-methane organic gases (NMOG) emissions for the 1700 x 1000 km2 domain were estimated at 23,800 metric tons/day (62% from Mexico and 38% from the United States), and biogenic NOx was estimated at 1230 metric tons/day (54% from Mexico and 46% from the United States) for the July 18-20, 1993, ozone episode. The biogenic NMOG represented 74% of the total NMOG emissions, and biogenic NOx was 14% of the total NOx. The CIT photochemical airshed model was used to assess how biogenic emissions impact air quality. Predicted ground-level ozone increased by 5-10 ppb in most rural areas, 10-20 ppb near urban centers, and 20-30 ppb immediately downwind of the urban centers compared to simulations in which only anthropogenic emissions were used. A sensitivity analysis of predicted ozone concentration to emissions was performed using the decoupled direct method for three dimensional air quality models (DDM-3D). The highest positive sensitivity of ground-level ozone concentration to biogenic volatile organic compound (VOC) emissions (i.e., increasing biogenic VOC emissions results in increasing ozone concentrations) was predicted to be in locations with high NOx levels, (i.e., the urban areas). One urban center--Houston--was predicted to have a slight negative sensitivity to biogenic NO emissions (i.e., increasing biogenic NO emissions results in decreasing local ozone concentrations). The highest sensitivities of ozone concentrations to on-road mobile source VOC emissions, all positive, were mainly in the urban areas. The highest sensitivities of ozone concentrations to on-road mobile source NOx emissions were predicted in both urban (either positive or negative sensitivities) and rural (positive sensitivities) locations.     

Nitrous oxide emissions from light duty vehicles

Nitrous oxide (N₂O) emissions measurements were made on light duty gasoline and light duty diesel vehicles during chassis dynamometer testing conducted at the Environment Canada and California Air Resources Board vehicle emissions laboratories between 2001 and 2007. Per phase and composite FTP emission rates were measured. A subset of vehicles was also tested using other driving cycles to characterize emissions as a function of different driving conditions. Vehicles were both new (<6500 km) and in-use (6500–160,000 km) and were tested on low sulfur gasoline (<30 ppm) or low sulfur diesel (<300 ppm). Measurements from selected published studies were combined with these new measurements to give a test fleet of 467 vehicles meeting both US EPA and California criteria pollutant emissions standards between Tier 0 and Tier 2 Bin 3 or SULEV. Aggregate distance-based and fuel-based emission factors for N₂O are reported for each emission standard and for each of the different test cycles. Results show that the distinction between light duty automobile and light duty truck is not significant for any of the emission standards represented by the test fleet and the distinction between new and aged catalyst is significant for vehicles meeting all emission standards but Tier 2. This is likely due to the relatively low mileage accumulated by the Tier 2 vehicles in this study as compared to the durability requirement of the standard. The FTP composite N₂O emission factors for gasoline vehicles meeting emission standards more stringent than Tier 1 are substantially lower than those currently used by both Canada and the US for the 2005 inventories. N₂O emission factors from test cycles other than the FTP illustrate the variability of emission factors as a function of driving conditions. N₂O emission factors are shown to strongly correlate with NMHC/NMOG emission standards and less strongly with NO_X and CO emission standards. A review of several published reports on the effect of gasoline sulfur content on N₂O emissions suggests that additional research is needed to adequately quantify the increase in N₂O emissions as a function of fuel sulfur.     

On-road measurement of fine particle and nitrogen oxide emissions from light- and heavy-duty motor vehicles

An updated assessment of fine particle emissions from light- and heavy-duty vehicles is needed due to recent changes to the composition of gasoline and diesel fuel, more stringent emission standards applying to new vehicles sold in the 1990s, and the adoption of a new ambient air quality standard for fine particulate matter (PM_2.5) in the United States. This paper reports the measurement of emissions from vehicles in a northern California roadway tunnel during summer 1997. Separate measurements were made of uphill traffic in two tunnel bores: one bore carried both light-duty vehicles and heavy-duty diesel trucks, and the second bore was reserved for light-duty vehicles. Ninety-eight percent of the light-duty vehicles were gasoline-powered. In the tunnel, heavy-duty diesel trucks emitted 24, 37, and 21 times more fine particle, black carbon, and sulfate mass per unit mass of fuel burned than light-duty vehicles. Heavy-duty diesel trucks also emitted 15–20 times the number of particles per unit mass of fuel burned compared to light-duty vehicles. Fine particle emissions from both vehicle classes were composed mostly of carbon; diesel-derived particulate matter contained more black carbon (51±11% of PM_2.5 mass) than did light-duty fine particle emissions (33±4%). Sulfate comprised only 2% of total fine particle emissions for both vehicle classes. Sulfate emissions measured in this study for heavy-duty diesel trucks are significantly lower than values reported in earlier studies conducted before the introduction of low-sulfur diesel fuel. This study suggests that heavy-duty diesel vehicles in California are responsible for nearly half of oxides of nitrogen emissions and greater than three-quarters of exhaust fine particle emissions from on-road motor vehicles.     

Characterization of Sonic Devices Used for Cleaning Fabric Filters

ABSTRACT

Ozone reactivity scales play an important role in selecting which chemical compounds are used in products ranging from gasoline to pesticides to hairspray in California, across the United States and around the world. The California Statewide Air Pollution Research Center (SAPRC) box model that calculates ozone reactivity uses a representative urban atmosphere to predict how much additional ozone forms for each kilogram of compound emission. This representative urban atmosphere has remained constant since 1988, even though more than 25 years of emissions controls have greatly reduced ambient ozone concentrations across the United States during this time period. Here we explore the effects of updating the representative urban atmosphere used for ozone reactivity calculations from 1988 to 2010 conditions by updating the meteorology, emission rates, concentration of initial conditions, concentration of background species, and composition of volatile organic compound (VOC) profiles. Box model scenarios are explored for 39 cities across the United States to calculate the Maximum Incremental Reactivity (MIR) scale for 1,233 individual compounds and compound-mixtures. Median MIR values across the cities decreased by approximately 20.3% when model conditions were updated. The decrease is primarily due to changes in atmospheric composition ultimately attributable to emissions control programs between 1998 and 2010. Further effects were caused by changes in meteorological variables stemming from shifting seasons for peak ozone events (summer versus early fall). Lumped model species with the highest MIR values in 1988 experienced the greatest decrease in MIR values when conditions were updated to 2010. Despite the reduction in the absolute reactivity in the updated 2010 atmosphere, the relative ranking of the VOCs according to their reactivity did not change strongly compared to the original 1988 atmosphere. These findings indicate that past decisions about ozone control programs remain valid today, and the ozone reactivity scale continues to provide relevant guidance for future policy decisions even as new products are developed.

Implications: Updating the representative urban atmosphere used for the Maximum Incremental Reactivity (MIR) scale from 1988 to 2010 conditions caused the reactivity of 1223 individual compounds and combined mixtures to decrease by an average of 20.3% but the relative ranking of the VOCs was not strongly affected. This means that previous guidance about preferred chemical formulations to reduce ozone formation in cities across the United States remain valid today, and the MIR scale continues to provide relevant guidance for future policy decisions even as new products are developed.     

Deriving fuel-based emission factor thresholds to interpret heavy-duty vehicle roadside plume measurements

Remote sensing devices have been used for decades to measure gaseous emissions from individual vehicles at the roadside. Systems have also been developed that entrain diluted exhaust and can also measure particulate matter (PM) emissions. In 2015, the California Air Resources Board (CARB) reported that 8% of in-field diesel particulate filters (DPF) on heavy-duty (HD) vehicles were malfunctioning and emitted about 70% of total diesel PM emissions from the DPF-equipped fleet. A new high-emitter problem in the heavy-duty vehicle fleet had emerged. Roadside exhaust plume measurements reflect a snapshot of real-world operation, typically lasting several seconds. In order to relate roadside plume measurements to laboratory emission tests, we analyzed carbon dioxide (CO₂), oxides of nitrogen (NO_X), and PM emissions collected from four HD vehicles during several driving cycles on a chassis dynamometer. We examined the fuel-based emission factors corresponding to possible exceedances of emission standards as a function of vehicle power. Our analysis suggests that a typical HD vehicle will exceed the model year (MY) 2010 emission standards (of 0.2 g NO_X/bhp-hr and 0.01 g PM/bhp-hr) by three times when fuel-based emission factors are 9.3 g NO_X/kg fuel and 0.11 g PM/kg using the roadside plume measurement approach. Reported limits correspond to 99% confidence levels, which were calculated using the detection uncertainty of emissions analyzers, accuracy of vehicle power calculations, and actual emissions variability of fixed operational parameters. The PM threshold was determined for acceleration events between 0.47 and 1.4 mph/sec only, and the NO_X threshold was derived from measurements where after-treatment temperature was above 200°C. Anticipating a growing interest in real-world driving emissions, widespread implementation of roadside exhaust plume measurements as a compliment to in-use vehicle programs may benefit from expanding this analysis to a larger sample of in-use HD vehicles.

Implications: Regulatory agencies, civil society, and the public at large have a growing interest in vehicle emission compliance in the real world. Leveraging roadside plume measurements to identify vehicles with malfunctioning emission control systems is emerging as a viable new and useful method to assess in-use performance. This work proposes fuel-based emission factor thresholds for PM and NOx that signify exceedances of emission standards on a work-specific basis by analyzing real-time emissions in the laboratory. These thresholds could be used to prescreen vehicles before roadside enforcement inspection or other inquiry, enhance and further develop emission inventories, and potentially develop new requirements for heavy-duty inspection and maintenance (I/M) programs, including but not limited to identifying vehicles for further testing.     

Characterization of Emissions from Vehicles Using Methanol and Methanol-Gasoline Blended Fuels

Exhaust and evaporative emissions were examined from vehicles fueled with methanol or a gasoline-methanol blend. Regulated automobile pollutants, as well as detailed hydrocarbons, methanol, and aldehydes were measured, and exhaust emission trends were obtained for vehicle operation over five different driving cycles. Results indicated that use of the blended fuel does not generally have any significant effect on base-line exhaust emission rates of regulated pollutants; however, emission rates of aldehydes increased during the Federal Test Procedure. Aldehyde emissions from the methanol-fueled car were roughly an order of magnitude higher than those resulting from blended fuel usage. The hydrocarbon composition of evaporative emissions with the blended fuel was similar to that with the base-line fuel except when canister breakthrough occurred. Evaporative emissions during breakthrough were comprised chiefly of N-butane.     

Projected ozone trends and changes in the ozone-precursor relationship in the South Coast Air Basin in response to varying reductions of precursor emissions

This study examined the effects of varying future reductions in emissions of oxides of nitrogen (NO_x) and volatile organic compounds (VOC) on the location and magnitude of peak ozone levels within California’s South Coast Air Basin (SoCAB or Basin). As ozone formation is currently VOC-limited in the Basin, model simulations with 2030 baseline emissions (?61% for NO_x and ?32% for VOC from 2008) predict 10–20% higher peak ozone levels (i.e., NO_x disbenefit) in the western and central SoCAB compared with the 2008 base simulation. With additional NO_x reductions of 50% beyond the 2030 baseline emissions (?81% from 2008), the predicted ozone levels are reduced by about 15% in the eastern SoCAB but remain comparable to 2008 levels in the western and central Basin. The Basin maximum ozone site shifts westward to more populated areas of the Basin and will result potentially in greater population-weighted exposure to ozone with even a relatively small shortfall in the required NO_x reductions unless accompanied by additional VOC reductions beyond 2030 baseline levels. Once committed to a NO_x-focused control strategy, NO_x reductions exceeding 90% from 2008 levels will be necessary to attain the ozone National Ambient Air Quality Standards (NAAQS). The findings from this study and other recent work that the current VOC emission estimates are underestimated by about 50% suggest that greater future VOC reductions will be necessary to reach the projected 2030 baseline emissions. Increasing the base year VOC emissions by a factor of 1.5 result in higher 2008 baseline ozone predictions, lower relative response factors, and about 20% lower projected design values. If correct, these findings have important implications for the total and optimum mix of VOC and NO_x emission reductions that will be required to attain the ozone NAAQS in the SoCAB.

Implications: Results of this study indicate that ozone levels in the western and central SoCAB would remain the same or increase with even a relatively small shortfall in the projected NO_x reductions under planned NO_x-focused controls. This possibility, therefore, warrants a rigorous analysis of the costs and effects of varying reductions of VOC and NO_x on the formation and combined health impacts of ozone and secondary particles. Given the nonlinearity of ozone formation, such analyses should include the implications of gradually increasing global background ozone concentrations and the Basin’s topography and meteorology on the practical limits of alternative emission control strategies.     

机动车尾气VOCs排放特征及减排措施研究

分析了机动车尾气挥发性有机物(VOCs)的排放特征,发现尾气VOCs排放具有明显的日变化和季节变化特征。不同区域不同车型机动车尾气VOCs成分谱略有差异,轻型汽油车尾气VOCs中芳香烃和烷烃含量较高,柴油车烷烃含量较高。尾气排放受机动车保有量、行驶里程、维护保养水平、行驶速度和燃油标准、排放标准等因素影响。从优先控制汽油车、加快机动车更新、采取本地化减排措施、加强多元管理措施、提高科研水平等方面提出了针对性的减排措施。     

An Evaluation of the Fuel Factor Through Direct Measurement of Photochemical Reactivity of Emissions

Findings in research at the Bureau of Mines Bartlesville Petroleum Research Center show that photochemical reactivities of vehicular emissions are reliably measured in laboratory experiments in which smog manifestations are observed directly. Results of the direct smog-chamber measurements reveal that the photochemical behavior of emissions may differ significantly from the behavior that is predicted from the exhaust composition using reactivity scales. The concept of direct measurement of reactivity was applied to determine differences in characteristics of emissions from 20 passenger vehicles, each tested using 10 different fuels. The primary objective of the fuel study was to assess the over-all effect on vehicle emissions of fuel modifications designed to reduce the photochemical pollution associated with automotive evaporative losses. A similar, brief, comparative study of leaded and nonleaded fuels was also made. Reducing volatility was found to reduce the over-all smog potential of vehicle emissions but involved some penalty by way of increased exhaust emissions. Replacing light olefin with the corresponding paraffin also reduced over-all smog potential and in this case exhaust reactivity was not affected. In general greater smog potential was found to be associated with prototype nonleaded fuels than with leaded fuels typical of products currently marketed.     

A Fuel-Based Motor Vehicle Emission Inventory

Abstract

A fuel-based methodology for calculating motor vehicle emission inventories is presented. In the fuel-based method, emission factors are normalized to fuel consumption and expressed as grams of pollutant emitted per gallon of gasoline burned. Fleet-average emission factors are calculated from the measured on-road emissions of a large, random sample of vehicles. Gasoline use is known at the state level from sales tax data, and may be disaggregated to individual air basins. A fuel-based motor vehicle CO inventory was calculated for the South Coast Air Basin in California for summer 1991. Emission factors were calculated from remote sensing measurements of more than 70,000 in-use vehicles. Stabilized exhaust emissions of CO were estimated to be 4400 tons/day for cars and 1500 tons/day for light-duty and medium- duty trucks, with an estimated uncertainty of ±20% for cars and ±30% for trucks. Total motor vehicle CO emissions, including incremental start emissions and emissions from heavy-duty vehicles were estimated to be 7900 tons/day. Fuelbased inventory estimates were greater than those of California's MVEI 7F model by factors of 2.2 for cars and 2.6 for trucks. A draft version of California's MVEI 7G model, which includes increased contributions from high-emitting vehicles and off-cycle emissions, predicted CO emissions which closely matched the fuel-based inventory. An analysis of CO mass emissions as a function of vehicle age revealed that cars and trucks which were ten or more years old were responsible for 58% of stabilized exhaust CO emissions from all cars and trucks.     

Trends in onroad transportation energy and emissions

Globally, 1.3 billion on-road vehicles consume 79 quadrillion BTU of energy, mostly gasoline and diesel fuels, emit 5.7 gigatonnes of CO₂, and emit other pollutants to which approximately 200,000 annual premature deaths are attributed. Improved vehicle energy efficiency and emission controls have helped offset growth in vehicle activity. New technologies are diffusing into the vehicle fleet in response to fuel efficiency and emission standards. Empirical assessment of vehicle emissions is challenging because of myriad fuels and technologies, intervehicle variability, multiple emission processes, variability in operating conditions, and varying capabilities of measurement methods. Fuel economy and emissions regulations have been effective in reducing total emissions of key pollutants. Real-world fuel use and emissions are consistent with official values in the United States but not in Europe or countries that adopt European standards. Portable emission measurements systems, which uncovered a recent emissions cheating scandal, have a key role in regulatory programs to ensure conformity between “real driving emissions” and emission standards. The global vehicle fleet will experience tremendous growth, especially in Asia. Although existing data and modeling tools are useful, they are often based on convenience samples, small sample sizes, large variability, and unquantified uncertainty. Vehicles emit precursors to several important secondary pollutants, including ozone and secondary organic aerosols, which requires a multipollutant emissions and air quality management strategy. Gasoline and diesel are likely to persist as key energy sources to mid-century. Adoption of electric vehicles is not a panacea with regard to greenhouse gas emissions unless coupled with policies to change the power generation mix. Depending on how they are actually implemented and used, autonomous vehicles could lead to very large reductions or increases in energy consumption. Numerous other trends are addressed with regard to technology, emissions controls, vehicle operations, emission measurements, impacts on exposure, and impacts on public health.

Implications: Without specific policies to the contrary, fossil fuels are likely to continue to be the major source of on-road vehicle energy consumption. Fuel economy and emission standards are generally effective in achieving reductions per unit of vehicle activity. However, the number of vehicles and miles traveled will increase. Total energy use and emissions depend on factors such as fuels, technologies, land use, demographics, economics, road design, vehicle operation, societal values, and others that affect demand for transportation, mode choice, energy use, and emissions. Thus, there are many opportunities to influence future trends in vehicle energy use and emissions.     

Exhaust Temperature Profiles for Application of Passive Diesel Particulate Filters to Solid Waste Collection Vehicles in California

Abstract

To reduce public exposure to diesel particulate matter (DPM), the California Air Resources Board has begun adoption of a series of rules to reduce these emissions from in-use heavy-duty vehicles. Passive diesel particulate filter (DPF) after-treatment technologies are a cost-effective method to reduce DPM emissions and have been used on a variety of vehicles worldwide. Two passive DPFs were interim-verified in California and approved federally for use in most 1994–2002 engine families for vehicles meeting min engine exhaust temperature requirements for successful filter regeneration. Some vehicles, however, may not be suited to passive DPFs because of lower engine exhaust temperatures. The purpose of this study was to determine the applicability of two types of passive DPFs to solid waste collection vehicles, the group of vehicles for which California recently mandated in-use DPM reductions. We selected 60 collection vehicles to represent the four main types of collection vehicle duty cycles—roll-offs, and front-end, rear, and side loaders—and collected second-by-second engine exhaust temperature readings for one week from each vehicle. As a group, the collection vehicles exhibited low engine exhaust temperatures, making the application of passive DPFs to these vehicles difficult. Only 35% of tested vehicles met the temperature requirements for one passive DPF, whereas 60% met the temperature requirements for the other. Engine exhaust temperatures varied by vehicle type. Side and front-end loaders met the engine exhaust temperature requirements in the greatest number of cases with ～50–90% achieving the required regeneration temperatures. Only 8–25% of the rear loader and roll-off collection vehicles met the engine exhaust temperature requirements. Solid waste collection vehicles represent a diverse fleet with a variety of duty cycles. Low engine exhaust temperatures will need to be addressed for successful use of passive DPFs in this application.     

Reductions in human benzene exposure in the California South Coast Air Basin

Benzene typically contributes a significant fraction of the human cancer risk associated with exposure to urban air pollutants. In recent years, concentrations of benzene in ambient air have declined in many urban areas due to the use of reformulated gasolines, lower vehicle emissions, and other control measures. In the California South Coast Air Basin (SoCAB) ambient benzene concentrations have been reduced by more than 70% since 1989. To estimate the resulting effect on human exposures, the Regional Human Exposure (REHEX) model was used to calculate benzene exposures in the SoCAB for the years 1989 and 1997. Benzene concentration distributions in 14 microenvironments (e.g. outdoor, home, vehicle, work) were combined with California time-activity patterns and census data to calculate exposure distributions for 11 demographic groups in the SoCAB. For 1997, the calculated average benzene exposure for nonsmoking adults in the SoCAB was 2 ppb, compared to 6 ppb for 1989. For nonsmokers, about half of the 1997 exposure was due to ambient air concentrations (including their contributions to other microenvironments), but only 4% for smokers. Passive tobacco smoke contributed about one-fourth of all exposure for adult nonsmokers. In-transit microenvironments and attached garages contributed approximately 15 and 10%, respectively. From 1989 to 1997, decreases in passive smoke exposure accounted for about one-sixth of the decrease in exposure for nonsmoking adults, with the remainder due to decreases in ambient concentrations. The reductions in exposure during this time period indicate the effectiveness of reformulated fuels, more stringent emission standards, and smoking restrictions in significantly reducing exposure to benzene.     

The Ozone Productivity of n-Propyl Bromide: Part 2—An Exception to the Maximum Incremental Reactivity Scale

Abstract

In an earlier paper the ozone-forming potential of n-propyl bromide (NPB) was studied with a new methodology designed to address issues associated with a marginal smog-forming compound. However, the U.S. Environmental Protection Agency (EPA) subsequently revised its policy and now recommends using the Maximum Incremental Reactivity (MIR) scale to rank the ozone-forming potential of all volatile organic compounds (VOCs), including those of marginal ozone productivity. Nevertheless, EPA contemplated exceptions to the box-model-derived MIR scale by allowing use of photochemical grid-model simulations for case specific reactivity assessments. The California Air Resources Board (CARB) also uses the MIR scale and CARB has a Reactivity Scientific Advisory Committee that can consider exceptions to the MIR scale. In this study, grid-model simulations that were recommended by EPA are used to evaluate the incremental ozone impacts of NPB using an update to the chemical mechanism developed in an earlier paper. New methods of analysis of the grid-model output are further developed here to quantify the relative reactivities between NPB and ethane over a wide range of conditions. The new grid-model-based analyses show that NPB is significantly different and generally less in ozone-forming potential (i.e., reactivity) than predicted by the box-model-based MIR scale relative to ethane, EPA’s “bright-line” test for non-VOC status. Although NPB has low reactivity compared to typical VOCs on any scale, the new grid-model analyses developed here show that NPB is far less reactive (and even has negative reactivity) compared to the reactivity predicted by the MIR scale.     

Exhaust temperature profiles for application of passive diesel particulate filters to solid waste collection vehicles in California

To reduce public exposure to diesel particulate matter (DPM), the California Air Resources Board has begun adoption of a series of rules to reduce these emissions from in-use heavy-duty vehicles. Passive diesel particulate filter (DPF) after-treatment technologies are a cost-effective method to reduce DPM emissions and have been used on a variety of vehicles worldwide. Two passive DPFs were interim-verified in California and approved federally for use in most 1994--2002 engine families for vehicles meeting min engine exhaust temperature requirements for successful filter regeneration. Some vehicles, however, may not be suited to passive DPFs because of lower engine exhaust temperatures. The purpose of this study was to determine the applicability of two types of passive DPFs to solid waste collection vehicles, the group of vehicles for which California recently mandated in-use DPM reductions. We selected 60 collection vehicles to represent the four main types of collection vehicle duty cycles--rolloffs, and front-end, rear, and side loaders--and collected second-by-second engine exhaust temperature readings for one week from each vehicle. As a group, the collection vehicles exhibited low engine exhaust temperatures, making the application of passive DPFs to these vehicles difficult. Only 35% of tested vehicles met the temperature requirements for one passive DPF, whereas 60% met the temperature requirements for the other. Engine exhaust temperatures varied by vehicle type. Side and front-end loaders met the engine exhaust temperature requirements in the greatest number of cases with approximately 50-90% achieving the required regeneration temperatures. Only 8-25% of the rear loader and roll-off collection vehicles met the engine exhaust temperature requirements. Solid waste collection vehicles represent a diverse fleet with a variety of duty cycles. Low engine exhaust temperatures will need to be addressed for successful use of passive DPFs in this application.     

Diagnosis and Repair of Excessively Emitting Vehicles

Abstract

Between 1991 and 1993, the California Air Resources Board (CARB) selected 1,115 vehicles from all across the South Coast Air Basin to evaluate the effectiveness of the state's existing biennial motor vehicle Inspection/Maintenance (I/M) or Smog Check program. The vehicles were chosen to represent the population of cars that "should fail" properly conducted inspections. The cars were emissions-tested at baseline and sent undercover to licensed I/M garages throughout the basin. Federal Test Procedure (FIT) emissions were measured again for cars that were repaired. In the second year of the study, the vehicles that could be reproduced were tested at the CARB to measure the level of emissions deterioration and any underhood changes in emission control systems. In the third year, the cycle of emissions testing and undercover inspections and repair was repeated.

This paper uses data from the study to explore the relationships between super emitting vehicles (defined here as vehicles whose emissions are several times California certification standards) and diagnostics and repair of their underhood emissions control systems. Also examined is their appearance and improvement during a three-year period that includes two cycles of inspection and repair. An important finding is that once normalized to account for differences in certification standards, the super emitting vehicles do not have a unique signature in terms of their underhood emission control system failure modes, mileage, or age, when compared with the average vehicle expected to fail a Smog Check inspection. However, they are more likely to be identified, diagnosed, and repaired effectively than other vehicles, although they continue to reappear over time.     

Optimized combinations of abatement strategies for urban mobile sources

The maximum incremental reactivity (MIR) scale was chosen as a practical index for quantifying ozone-forming impacts. The integer linear and nonlinear programming techniques were employed as the optimization method to maximize MIR and volatile organic compound (VOC) reductions, and minimize ozone's marginal cost with varied control costs. Mobile vehicles were divided into nine categories according to the demands of decision makers and the distinctive features of local circumstance in metro-Taipei. The emission factor (EF) and vehicle kilometers traveled (VKT) of each kind of vehicle were estimated by MOBILE5B model via native parameters and questionnaires. Compressed natural gas (CNG) and inspection and maintenance (I/M) were the alternative control programs for buses and touring buses; liquefied petroleum gas (LPG), I/M, methanol, electrical vehicle (EV) were for taxis and low duty gasoline vehicles. EV, methanol, and I/M were the possible control methods for two-stroke and four-stroke engine motorcycles; I/M programs for low-duty diesel trucks, heavy-duty diesel trucks, and low-duty gasoline trucks. The results include the emission ratios of specific vehicle to all vehicles, the best combination of abated measures based on different objectives, and the marginal cost for ozone and VOC with varied control costs.     

The ozone productivity of n-propyl bromide: Part 2--An exception to the Maximum Incremental Reactivity Scale

In an earlier paper the ozone-forming potential of n-propyl bromide (NPB) was studied with a new methodology designed to address issues associated with a marginal smog-forming compound. However, the U.S. Environmental Protection Agency (EPA) subsequently revised its policy and now recommends using the Maximum Incremental Reactivity (MIR) scale to rank the ozone-forming potential of all volatile organic compounds (VOCs), including those of marginal ozone productivity. Nevertheless, EPA contemplated exceptions to the box-model-derived MIR scale by allowing use of photochemical grid-model simulations for case specific reactivity assessments. The California Air Resources Board (CARB) also uses the MIR scale and CARB has a Reactivity Scientific Advisory Committee that can consider exceptions to the MIR scale. In this study, grid-model simulations that were recommended by EPA are used to evaluate the incremental ozone impacts of NPB using an update to the chemical mechanism developed in an earlier paper. New methods of analysis of the grid-model output are further developed here to quantify the relative reactivities between NPB and ethane over a wide range of conditions. The new grid-model-based analyses show that NPB is significantly different and generally less in ozone-forming potential (i.e., reactivity) than predicted by the box-model-based MIR scale relative to ethane, EPA's "bright-line" test for non-VOC status. Although NPB has low reactivity compared to typical VOCs on any scale, the new grid-model analyses developed here show that NPB is far less reactive (and even has negative reactivity) compared to the reactivity predicted by the MIR scale.