Zero-valent iron particles for PCB degradation and an evaluation of their effects on bacteria,plants, and soil organisms

Two types of nano-scale zero-valent iron (nZVI-B prepared by borohydride reduction and nZVI-T produced by thermal reduction of iron oxide nanoparticles in H₂) and a micro-scale ZVI (mZVI) were compared for PCB degradation efficiency in water and soil. In addition, the ecotoxicity of nZVI-B and nZVI-T particles in treated water and soil was evaluated on bacteria, plants, earthworms, and ostracods. All types of nZVI and mZVI were highly efficient in degradation of PCBs in water, but had little degradation effect on PCBs in soil. Although nZVI-B had a significant negative impact on the organisms tested, treatment with nZVI-T showed no negative effect, probably due to surface passivation through controlled oxidation of the nanoparticles.

     

Degradation of explosives-related compounds using nickel catalysts

We report the ability of nickel-based catalysts to degrade explosives compounds in aqueous solution. Several nickel catalysts completely degraded the explosives, although rates varied. Nearly all of the organic explosive compounds tested, including 2,4,6-trinitrotoluene (TNT), hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), were rapidly degraded to below detection limits by a powdered nickel on an alumina-silicate support (Aldrich nickel catalyst). Perchlorate degradation was minimal (<25%). Degradation of TNT by Aldrich nickel catalyst resulted in apparent first-order kinetics. Significant gaseous 14C was released and collected in an alkaline solution (most likely carbon dioxide) from [14C]RDX and [14C]HMX, indicating heterocyclic ring cleavage. Significant gaseous 14C was not produced from [14C]TNT, but spectrophotometric evidence indicated loss of aromaticity. Degradation occurred in low ionic strength solutions, groundwater, and from pH 3 to pH 9. Degradation of TNT, RDX, and HMX was maintained in flow-through columns of Aldrich nickel catalyst mixed with sand down to a hydraulic retention time of 4h. These data indicate that nickel-based catalysts may be an effective means for remediation of energetics-contaminated groundwater.     

Effects, transfer, and fate of RDX from aged soil in plants and worms

The objectives of this study were to provide data that can be used to predict exposure-based effects of RDX in aged soil on multiple endpoint organisms representing two trophic levels. These data can be used for defining criteria or reference values for environmental management and conducting specific risk assessment. Dose-response experiments formed the basis for the evaluation of toxic effects and transfer of contaminants from soil into two trophic levels. Long-term exposure tests were conducted to evaluate chronic, sublethal, toxicity and transfer of aged soil-based explosives, with RDX as main contaminant. In these tests, plants were exposed for 55 days in the greenhouse, biomass was determined and residues of explosives parent compounds and RDX metabolites were analyzed using HPLC techniques. Worms were exposed for 28 days (Eisenia fetida) and 42 days (Enchytraeus crypticus) in the laboratory, biomass and number were determined, and tissues were analyzed for explosives compounds. The plants tolerated concentrations up to 1,540 mg RDX kg(-1) soil-DW. Biomass of Lolium perenne was not significantly related to soil-RDX concentration, while biomass of Medicago sativa significantly increased. No screening benchmark for RDX in soil for plants was calculated, since concentrations up to 1,540 mg kg(-1) soil failed to reduce biomass by 20% as required for a LOEC. RDX, RDX-metabolite MNX, and accompanying HMX concentrations in plants were significantly related to concentrations in soil after 55 days of exposure (RDX: R(2) = 0.77-0.89; MNX R(2) = 0.53-0.77; HMX: R(2) = 0.67-0.71). The average bioconcentration factors (BCF) were for RDX 17 in L. perenne and 37 in M. sativa, and for HMX 2 in L. perenne and 44 in M. sativa. The worms also tolerated concentrations up to 1,540 mg RDX kg(-1) soil-DW. Biomass of E. fetida adults decreased with soil-RDX concentration, and a LOEC of 1,253 mg kg(-1) soil-DW was estimated. RDX concentrations in E. fetida were significantly related to concentrations in soil after 28-day exposure (R(2) = 0.88). The average BCF in E. fetida for RDX was 1. Because in response to exposure to RDX-contaminated soil the RDX concentrations in plants increased initially and decreased subsequently, while those in worms increased continuously, RDX in worm tissues may accumulate to higher concentrations than in plant tissues, regardless of the low average BCF for worms.     

Studies on plant-mediated fate of the explosives RDX and HMX

The fate of the explosives RDX and HMX on exposure to plants was investigated in 'natural' aquatic systems of Myriophyllum aquaticum for 16 days, and in axenic hairy root cultures of Catharanthus roseus for > or = 9 weeks. Exposure levels were: HMX, 5 mg/l; and RDX, approximately 8 mg/l. Exposure outcomes observed include: HMX, no transformation by aquatic plants, and minimal biological activity by axenic roots; and RDX, removal by both plant systems. In the case of RDX exposure to axenic roots, since 14C-RDX was included, removal was confirmed by the accumulation of 14C-label in the biomass. The intracellular 14C-label in these RDX studies was detected in two forms: intact RDX and bound unknown(s).     

Anaerobic biotransformation of explosives in aquifer slurries amended with ethanol and propylene glycol

Hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), and 2,4,6-trinitrotoluene (TNT) are explosives that are frequently found as environmental contaminants on military installations. Hydrogen has been shown to support the anaerobic transformation of these explosives. We investigated ethanol and propylene glycol as electron donors for providing syntrophically produced H2 for stimulating the anaerobic biodegradation of explosives in contaminated soil. The study was conducted using anoxic microcosms constructed with slurries of the contaminated soil and groundwater. The addition of 5mM ethanol and propylene glycol enhanced the biodegradation of RDX and HMX relative to the control bottles. Ethanol was depleted within about 20 days, resulting in the transient formation of hydrogen, acetate, and methane. The hydrogen headspace concentration increased from 8 ppm to 1838 ppm before decreasing to background concentrations. Propylene glycol was completely degraded after 15 days, forming hydrogen, propionate, and acetate as end-products. The hydrogen headspace concentrations increased from 56 ppm to 628 ppm before decreasing to background concentrations. No methane formation was observed during the incubation period of 48 days. Our findings indicate the addition of ethanol and propylene to the aquifer slurries increased the hydrogen concentrations and enhanced the biotransformation of RDX and HMX in the explosive-contaminated soil.     

Heterogeneous Fenton oxidation of Direct Black G in dye effluent using functional kaolin-supported nanoscale zero iron

This study investigated kaolin-supported nanoscale zero-valent iron (nZVI/K) as a heterogeneous Fenton-like catalyst for the adsorption and oxidation of an azo dye, Direct Black G (DBG). New findings suggest that kaolin as a support material not only reduced the aggregation of nanoscale zero-valent iron (nZVI) but also improved the adsorption of DBG. It consequently improved Fenton oxidation by increasing the local concentration of DBG in the vicinity of nZVI. This was confirmed by scanning electron microscopy and X-ray diffraction for the surface morphology of nZVI/K before and after the Fenton-like reaction. Furthermore, nZVI/K proved to be a catalyst for the heterogeneous Fenton-like oxidation of the DBG process in the neutral pH range. More than 87.22 % of DBG was degraded, and 54.60 % of total organic carbon was removed in the optimal conditions: 0.6 g/L dosage of nZVI/K, 33 mM H₂O₂, 100 mg/L initial DBG concentration, temperature of 303 K and pH of 7.06. Finally, it was demonstrated that nZVI/K removed DBG from dye wastewater through the processes of adsorption and oxidation.     

Treatment of phenol-containing wastewater by photoelectro-Fenton method using supported nanoscale zero-valent iron

This study presents the degradation of phenol by the photoelectro-Fenton method using nano zero-valent iron (nZVI) immobilized in polyvinyl alcohol–alginate beads. The effect of nZVI loading, H₂O₂ concentration, pH, and initial phenol concentration on phenol degradation and chemical oxygen demand reduction was studied. The scanning electron microscope images of the nZVI beads were used to analyze their morphology, and their diameters were in the range of 500–600 μm. The concentration of nZVI in the beads was varied from 0.1 to 0.6 g/L. Fe²⁺ leakage of 1 and 3 % was observed with 0.5 and 0.6 g/L of nZVI, respectively, and the observed beads' fracture frequency was 2 %, which confirmed the stability of the beads. The optimum operating conditions that arrived for better degradation were 0.5 g/L of nZVI, pH 6.2, and 400 mg H₂O₂/L. The treatment of effluent by this method increased the biodegradability index of the effluent, and the degradation data were found to follow pseudo first-order kinetics.     

A case study of contaminants on military ranges: Camp Edwards, Massachusetts, USA

An extensive investigation at the Camp Edwards, Massachusetts Military Reservation (MMR) demonstrates that assessment of groundwater and soil contamination at military ranges can be limited primarily to explosive-related compounds such as RDX, HMX, perchlorate, TNT and their transformation products. A modified analytical method is recommended to expand the list of explosives and to improve the detection limits. Analyses of metals, VOCs, SVOCs, and TICs are unnecessary. Soil samples may require the analyses of PAHs and PCNs for burn areas. Camp Edwards, as one of the few military ranges that have been exhaustively investigated for contaminants, is an ideal point of departure for evaluating other ranges. The permeable site soils promote leaching of contaminants and inhibit biotic and abiotic transformations. Moreover, the site has experienced an unusual extent of activities in its more than ninety years of active use. The recommendations in this report are based on data obtained for more than 200 analytes from more than 15,000 environmental samples.     

Sequential biodegradation of TNT,RDX and HMX in a mixture

We describe TNT's inhibition of RDX and HMX anaerobic degradation in contaminated soil containing indigenous microbial populations. Biodegradation of RDX or HMX alone was markedly faster than their degradation in a mixture with TNT, implying biodegradation inhibition by the latter. The delay caused by the presence of TNT continued even after its disappearance and was linked to the presence of its intermediate, tetranitroazoxytoluene. PCR–DGGE analysis of cultures derived from the soil indicated a clear reduction in microbial biomass and diversity with increasing TNT concentration. At high-TNT concentrations (30 and 90 mg/L), only a single band, related to Clostridium nitrophenolicum, was observed after 3 days of incubation. We propose that the mechanism of TNT inhibition involves a cytotoxic effect on the RDX- and HMX-degrading microbial population. TNT inhibition in the top active soil can therefore initiate rapid transport of RDX and HMX to the less active subsurface and groundwater.     

Assessing the impact of nano- and micro-scale zerovalent iron particles on soil microbial activities: particle reactivity interferes with assay conditions and interpretation of genuine microbial effects

The effects of nano-scale and micro-scale zerovalent iron (nZVI and mZVI) particles on general (dehydrogenase and hydrolase) and specific (ammonia oxidation potential, AOP) activities mediated by the microbial community in an uncontaminated soil were examined. nZVI (diameter 12.5 nm; 10 mg g⁻¹ soil) apparently inhibited AOP and nZVI and mZVI apparently stimulated dehydrogenase activity but had minimal influence on hydrolase activity. Sterile experiments revealed that the apparent inhibition of AOP could not be interpreted as such due to the confounding action of the particles, whereas, the nZVI-enhanced dehydrogenase activity could represent the genuine response of a stimulated microbial population or an artifact of ZVI reactivity. Overall, there was no evidence for negative effects of nZVI or mZVI on the processes studied. When examining the impact of redox active particles such as ZVI on microbial oxidation-reduction reactions, potential confounding effects of the test particles on assay conditions should be considered.     

复合介质渗透反应格栅去除地下水中的氨氮

针对受低浓度氨氮污染的地下水,实验筛选组合了不同的反应介质,利用串联的多介质填充柱模拟渗透反应格栅,通过物理吸附及生物硝化-反硝化作用来实现氮的去除。结果表明,在进水氨氮浓度为10 mg/L、流速为0.5 m/d的条件下,模拟柱对氨氮的去除率达到98%以上,且不会出现亚硝酸盐及硝酸盐浓度的升高。水体经过释氧柱后溶解氧由2mg/L升高至10 mg/L以上,表明释氧材料可提供硝化细菌所需的好氧环境。好氧柱中填充易于生物挂膜的生物陶粒及对氨氮有较强吸附能力的沸石,二者联用通过生物硝化-物理吸附协同作用实现对氨氮的去除,其中生物作用实现的氨氮去除量占总去除量的50%左右。后续厌氧反应柱填充海绵铁除氧并利用松树皮颗粒作为碳源,创造反硝化菌生长条件,硝酸盐氮浓度可由10 mg/L降低至5 mg/L以下,实现对好氧反应阶段所产生的硝酸盐的去除,避免了地下水的二次污染。     

Effectiveness of nanoscale zero-valent iron for treatment of a PCE-DNAPL source zone

Nanoscale zero-valent iron (nZVI) has received considerable attention as a potential in situ remediation technology for treating chlorinated solvent source zones. Experimental and mathematical modeling studies were conducted to investigate the performance of nZVI in the transformation of tetrachloroethene (PCE) entrapped as a dense nonaqueous phase liquid (DNAPL). Injection of a 60 g/L suspension of nZVI into a column containing 20-30 mesh Ottawa sand and PCE-DNAPL at a residual saturation of 5.5% resulted in a uniform distribution of nZVI and minimal displacement of PCE. Subsequent flushing with 267 pore volumes of water containing 3mM CaCl(2) at a Darcy velocity of 0.75 m/day resulted in steady-state effluent concentrations of PCE near the solubility limit (ca. 200mg/L) and production of dissolved-phase ethene (10-30 mg/L). Over the duration of the experiment, approximately 30% of the initial PCE-DNAPL mass reacted to form ethene, 50% was eluted as dissolved-phase PCE, and 20% remained in the column as PCE-DNAPL. To further explore the implications of the nZVI column results, a multiphase transport model was developed that incorporated rate-limited PCE-DNAPL dissolution and reactions with nZVI. Using a fitted pseudo first-order transformation rate coefficient of 1.421/h, the model accurately captured observed trends in effluent concentrations of PCE and ethene and overall mass balance. A model sensitivity study reveals a strong dependence of treatment effectiveness on system characteristics. The sensitivity analysis suggests that an increase in the extent of PCE transformation is facilitated by decreasing flow rate, emplacement of nZVI down-gradient of the DNAPL source zone, and decreasing length of the DNAPL source zone. These findings indicate that, although emplacement of high concentrations of nZVI within a PCE-DNAPL source zone can result in substantial transformation of the parent compound, careful attention to design parameters (e.g. flow rate, location and amount nZVI delivered) will be required to achieve complete conversion to benign reaction products.     

Dissolution rates of three high explosive compounds: TNT,RDX, and HMX

Incidental exposure to high explosive compounds can cause subtle health effects to which a population could be more susceptible than injury by detonation. Proper source characterization is a key requirement in the conduct of risk assessments. For nonvolatile solid explosives, dissolution is one of the primary mechanisms that controls fate and transport, resulting in exposure to these compounds remote from their source. To date, information describing dissolution rates of high explosives has been sparse. The objective of this study was to determine the dissolution rates of three high explosive compounds, 2,4,6-trinitrotoluene (TNT), hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), in dilute aqueous solutions as a function of temperature, surface area, and energy input. To determine each variable's impact on dissolution rate, experiments were performed where one variable was changed while the other two were held constant. TNT demonstrated the fastest dissolution rate followed by HMX and then RDX. Dissolution rate correlation equations were developed for each explosive compound incorporating the three aforementioned variables, independently, and collectively in one correlation equation.     

Effect of solution pH on aging dynamics and surface structural evolution of mZVI particles: H<Subscript>2</Subscript> production and spectroscopic/microscopic evidence

A microscale zero-valent iron (mZVI)-based in situ reactive zone is a promising technology for contaminated groundwater remediation. Estimation of mZVI aging behavior after its injection into the subsurface is essential for efficiency and longevity assessments. In this study, batch tests were conducted to investigate the effect of initial pH on mZVI aging dynamics, as well as the formation and evolution of aging products over 112 days. Results indicated that mZVI aging accelerated with decreasing initial pH. Corrosion rates of mZVI particles under pH 6.0 and 7.5 were approximately two orders of magnitude higher than those observed at pH 9.0. The morphological, structural, and compositional evolution of mZVI particles in three systems (pH = 6.0, 7.5, and 9.0) were investigated using scanning electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. In acidic and neutral solutions, a thick passivation layer with loosely and unevenly distributed aging precipitates was observed, and Fe₃O₄ was the final aging precipitate. Nevertheless, in alkaline solutions, minute aging precipitates were detected on the mZVI surface at 112 day. Characterization results suggested that mZVI was oxidized via the Fe⁰–Fe(OH)₂–Fe₃O₄ route. These findings shed new light on mZVI aging mechanisms, particularly its physicochemical characteristics and the structural evolution of mZVI in field-scale groundwater remediation applications.     

Nanoscale zero-valent iron (nZVI): aspects of the core-shell structure and reactions with inorganic species in water

Aspects of the core-shell model of nanoscale zero-valent iron (nZVI) and their environmental implications were examined in this work. The structure and elemental distribution of nZVI were characterized by X-ray energy-dispersive spectroscopy (XEDS) with nanometer-scale spatial resolution in an aberration-corrected scanning transmission electron microscope (STEM). The analysis provides unequivocal evidence of a layered structure of nZVI consisting of a metallic iron core encapsulated by a thin amorphous oxide shell. Three aqueous environmental contaminants, namely Hg(II), Zn(II) and hydrogen sulfide, were studied to probe the reactive properties and the surface chemistry of nZVI. High-resolution X-ray photoelectron spectroscopy (HR-XPS) analysis of the reacted particles indicated that Hg(II) was sequestrated via chemical reduction to elemental mercury. On the other hand, Zn(II) removal was achieved via sorption to the iron oxide shell followed by zinc hydroxide precipitation. Hydrogen sulfide was immobilized on the nZVI surface as disulfide (S(2)(2-)) and monosulfide (S(2-)) species. Their relative abundance in the final products suggests that the retention of hydrogen sulfide occurs via reactions with the oxide shell to form iron sulfide (FeS) and subsequent conversion to iron disulfide (FeS(2)). The results presented herein highlight the multiple reactive pathways permissible with nZVI owing to its two functional constituents. The core-shell structure imparts nZVI with manifold functional properties previously unexamined and grants the material with potentially new applications.     

The impact of zero-valent iron nanoparticles upon soil microbial communities is context dependent

Nanosized zero-valent iron (nZVI) is an effective land remediation tool, but there remains little information regarding its impact upon and interactions with the soil microbial community. nZVI stabilised with sodium carboxymethyl cellulose was applied to soils of three contrasting textures and organic matter contents to determine impacts on soil microbial biomass, phenotypic (phospholipid fatty acid (PLFA)), and functional (multiple substrate-induced respiration (MSIR)) profiles. The nZVI significantly reduced microbial biomass by 29 % but only where soil was amended with 5 % straw. Effects of nZVI on MSIR profiles were only evident in the clay soils and were independent of organic matter content. PLFA profiling indicated that the soil microbial community structure in sandy soils were apparently the most, and clay soils the least, vulnerable to nZVI suggesting a protective effect imparted by clays. Evidence of nZVI bactericidal effects on Gram-negative bacteria and a potential reduction of arbuscular mycorrhizal fungi are presented. Data imply that the impact of nZVI on soil microbial communities is dependent on organic matter content and soil mineral type. Thereby, evaluations of nZVI toxicity on soil microbial communities should consider context. The reduction of AM fungi following nZVI application may have implications for land remediation.     

Microbial reduction of nitrate in the presence of nanoscale zero-valent iron

Microbial reduction of nitrate in the presence of nanoscale zero-valent iron (NZVI) was evaluated to assess the feasibility of employing NZVI in the biological nitrate treatment. Nitrate was completely reduced within 3 d in a nanoscale Fe(0)-cell reactor, while only 50% of the nitrate was abiotically reduced over 7 d at 25 °C. The removal rate of nitrate in the integrated NZVI-cell system was unaffected by the presence of high amounts of sulfate. Efficient removal of nitrate by Fe(II)-supported anaerobic culture in 14 d indicated that Fe(II), which is produced during anaerobic iron corrosion in the Fe(0)-cell system, might act as an electron donor for nitrate. Unlike abiotic reduction, microbial reduction of nitrate was not significantly affected by low temperature conditions. This study demonstrated the potential applicability of employing NZVI iron as a source of electrons for biological nitrate reduction. Use of NZVI for microbial nitrate reduction can obviate the disadvantages associated with traditional biological denitrification, that relies on the use of organic substrates or explosive hydrogen gas, and maintain the advantages offered by nano-particle technology such as higher surface reactivity and functionality in suspensions.     

Effective adsorbent for arsenic removal: core/shell structural nano zero-valent iron/manganese oxide

Recently, nano zero-valent iron (nZVI) has emerged as an effective adsorbent for the removal of arsenic from aqueous solutions. However, its use in various applications has suffered from reactivity loss resulting in a decreased efficiency. Thus, the aim of this study was to develop an effective arsenic adsorbent as a core/shell structural nZVI/manganese oxide (or nZVI/Mn oxide) to minimize the reactivity loss of the nZVI. As the major result, the arsenic adsorption capacities of the nZVI/Mn oxide for As(V) and As(III) were approximately two and three times higher than that of the nZVI, respectively. In addition, the As(V) removal efficiency of the nZVI/Mn oxide was maintained through 4 cycles of regeneration whereas that of the nZVI was decreased significantly. The enhanced reactivity and reusability of the nZVI/Mn oxide can be successfully explained by the synergistic interaction of the nZVI core and manganese oxide shell, in which the manganese oxides participate in oxidation reactions with corroded Fe²⁺ and subsequently retard the release of aqueous iron providing additional surface sites for arsenic adsorption. In summary, this study reports the successful fabrication of a core/shell nZVI/Mn oxide as an effective adsorbent for the removal of arsenic from aqueous solutions.     

Effectiveness of zerovalent iron and nickel catalysts for degrading chlorinated solvents and n-nitrosodimethylamine in natural groundwater.

Laboratory batch experiments were performed to evaluate the effectiveness of nickel catalysts, nanoscale zerovalent iron (nZVI) doped with palladium, and microscale ZVI for treatment of tetrachloroethene, trichloroethene, and n-nitrosodimethylamine (NDMA) in soil-groundwater slurries. Results indicated that the presence of NDMA inhibited degradation of chlorinated solvents. Although both the nickel catalyst and nZVI were able to degrade NDMA in deionized water, neither of these metals was effective at degrading NDMA in the soil-groundwater system evaluated in this study. The effectiveness of the nickel catalyst and nZVI, with respect to treatment of the chlorinated solvents, also appeared to be highly dependent on the groundwater geochemical conditions. Overall results of this study suggest that the degradation mechanisms involving nickel catalysts and nZVI in natural soil/groundwater systems are not well-understood, and addition of metal catalysts to ZVI may not necessarily enhance observed degradation rates in natural systems.     

Anaerobic treatment of army ammunition production wastewater containing perchlorate and RDX

Perchlorate is an oxidizer that has been routinely used in solid rocket motors by the Department of Defense and National Aeronautics and Space Administration. Royal Demolition Explosive (RDX) is a major component of military high explosives and is used in a wide variety of munitions. Perchlorate bearing wastewater typically results from production of solid rocket motors, while RDX is transferred to Army industrial wastewaters during load, assemble and pack operations for new munitions, and hot water or steam washout for disposal and deactivation of old munitions (commonly referred to as demilitarization, or simply demil). Biological degradation in Anaerobic Fluidized Bed Reactors (AFBR), has been shown to be an effective method for the removal of both perchlorate and RDX in contaminated wastewater. The focus of this study was to determine the effectiveness of removal of perchlorate and RDX, individually and when co-mingled, using ethanol as an electron donor under steady state conditions. Three AFBRs were used to assess the effectiveness of this process in treating the wastewater. The performance of the bioreactors was monitored relative to perchlorate, RDX, and chemical oxygen demand removal effectiveness. The experimental results demonstrated that the biodegradation of perchlorate and RDX was more effective in bioreactors receiving the single contaminant than in the bioreactor where both contaminants were fed.