Chemical Valorization of Forest and Agricultural By-Products. Obtention,Chemical Characteristics,and Mechanical Behavior of a Novel Family of Hydrophobic Films

Abstract

Esterification of hemicelluloses of the xylan family was performed in order to produce hydrophobic films. Acylation reactions were carried out with lauroyl chloride in the N,N-dimethylacetamide/lithium chloride homogeneous system using 4-dimethylaminopyridine as activator and were induced by microwave irradiation. In the experimental conditions used, 108 and 172% mass ratios were obtained for the dodecyl-grafted xylan and heteroxylan, respectively. The degrees of substitution (DS) were 1.3 (maximum 2) for xylan and 1.2 (maximum 2.1) for heteroxylan. These products were further characterized by FT-IR spectroscopy. The mechanical and thermomechanical behavior of this new family of hydrophobic films were analyzed and compared to those obtained from cellulose with a similar DS by the means of tensile tests. Our results indicate that the dodecyl-grafted xylan film presents the best rigidity—resistance to traction ratio.     

Efficient adsorption of the mycotoxins zearalenone and T-2 toxin on a modified yeast glucan

1,3-Beta-D-glucan derived from baker's yeast was chemically modified in two steps yielding crosslinked carboxymethyl glucan as the sodium salt (2). After cation exchange with hexadecyltrimethylammonium chloride, a hydrophobic adsorbent (3) was obtained which showed an excellent binding of the estrogenic mycotoxin zearalenone with a maximum adsorption of up to 183 mg/g. Compound 3 additionally showed a relatively high adsorption capacity for the trichothecene T-2 toxin of at least 10 mg/g. Starting from 2, various derivatives were prepared by cation exchange using quaternary ammonium salts bearing substituents besides methyl from four to 18 carbon atoms. The adsorption of T-2 toxin on these derivatives were compared with compound 3 leading to the conclusion that 3 is the best adsorbent of all investigated tetraalkylammonium-modified derivatives of 2.     

Effects of pH, temperature, and water quality on chloride removal with ultra-high lime with aluminum process.

The ultra high-lime with aluminum process (UHLA) has the ability to remove sulfate and chloride in addition to other scale-forming materials from recycled cooling water. Laboratory experiments have demonstrated that the UHLA process can achieve high chloride removal from recycled cooling water, and an equilibrium model was developed to describe chemical behavior during chloride removal. This paper describes the influence of pH, temperature, and initial chloride concentration on chloride removal by UHLA and identifies the precipitated solids formed during treatment. The optimum pH for maximum chloride removal efficiency was found to be 12 +/- 0.2. Chloride removal efficiency was higher at a high initial chloride concentration than at a low initial chloride concentration with the chemical doses used. Solids formed during UHLA treatment were identified by x-ray diffraction as calcium chloroaluminate, tricalcium hydroxyaluminate, and tetracalcium hydroxyaluminate. This supports the assumption of the equilibrium model that these compounds are present and form a solid solution.     

Sorption and desorption behavior of benzidine in different solvent-sediment systems

The sorption and desorption behavior of benzidine in eight solvent-sediment systems were studied using a batch method. The solvents tested included deionized water (DI), calcium chloride solution (CaCl2), sodium hydroxide solution (NaOH), acetonitrile (ACN), a mixture of acetonitrile and ammonium acetate solution (ACN-NH4OAc), methanol (MeOH), ammonium acetate solution (NH4OAc) and hydrochloric acid solution (HCl). Three sets of sorption isotherm experiments were conducted separately in these eight solvents with seven days, three weeks, and two months of contact times, respectively. The results demonstrated nonlinear benzidine sorption phenomena in all eight solvents with higher sorption affinities for sediment sites in the aqueous solvents than in the organic solvents. The results from the desorption experiments revealed that the benzidine desorption efficiencies in the solvents decreased in an order, which was approximately the reverse order of its sorption affinity. Results also suggested that hydrophobic partitioning and covalent binding processes dominated in the desorption experiments, while cation exchange process had little effect on desorption of benzidine. A three-stage model was subsequently applied to simulate the desorption data in the selected solvents of ACN, ACN-NH4OAc and NaOH, respectively. The rapidly desorbing initial fractions were about 0.13-0.20, 0.15-0.26, and 0.18-0.25 for ACN, ACN-NH4OAc and NaOH, respectively. Finally, the sorbed concentrations of benzidine in slowly and very slowly desorbing domains in the selected solvents were correlated with the maximum sorption capacities obtained from the Langmuir sorption isotherm model. The maximum sorption capacities of benzidine were found to be comparable to the amount of benzidine residing in the slowly and very slowly desorbing domains.     

铁盐和铝盐混凝对印染废水生化出水中溶解性有机污染物的去除特性

以三氯化铁和硫酸铝为混凝剂,印染废水二级生化出水为研究对象,并利用XAD-8/XAD-4吸附树脂联用技术将印染废水生化出水中溶解性有机物分为疏水酸、非酸疏水物质、弱疏水物质及亲水物质4类有机物,通过小试实验探讨了2种混凝剂对生化出水中各类溶解性有机物的去除效果及特点。实验结果表明,对于该印染废水的生化出水,溶解性有机物的主要成分是疏水性物质,以DOC表征时占总DOC的75%,其中疏水酸约占41%,疏水性物质也是引起色度的主要物质,所占比例以ADMI7.6表征时为89%,其中以非酸疏水物质的贡献最大,达到52%,并且非酸疏水物质中不饱和双键或芳香环有机物的含量较高。在三氯化铁和硫酸铝各自最佳的混凝条件下,均能够有效去除由疏水性物质（疏水酸和非酸疏水物质）引起的色度,但三氯化铁对弱疏水性物质以及亲水物质的去除率高于硫酸铝,这使得三氯化铁对印染废水生化出水中的溶解性有机物的去除效果优于硫酸铝。并且三氯化铁和硫酸铝混凝工艺均能明显降低生化出水的毒性。     

Enhanced phytoextraction of Cu, Pb, Zn and Cd with EDTA and EDDS

Chemically enhanced phytoextraction has been proposed as an effective approach to removing heavy metals from contaminated soil through the use of high biomass plants. Using pot experiments, the effects of the application of EDTA, EDDS and citric acid on the uptake of Cu, Pb, Zn and Cd by corn (Zea mays L. cv. Nongda 108) and bean (Phaseolus vulgaris L. white bean) plants were studied. The results showed that EDDS was more effective than EDTA at increasing the concentration of Cu in corn and beans. The application of 5 mmol kg-1 soil EDDS to soil significantly increased concentrations of Cu in shoots, with maximum levels of 2060 and 5130 mg kg-1 DW in corn and beans, respectively, which were 45- and 135-fold higher than that in the corresponding control plants to which chelate had not been applied. Concentrations of Zn in shoots were also higher in the plants treated with EDDS than in those treated with EDTA. For Pb and Cd, EDDS was less effective than EDTA. The maximum Cu phytoextraction was found with the EDDS treatment. The application of EDTA and EDDS also significantly increased the shoot-to-root ratios of the concentrations of Cu, Pb, Zn and Cd in both plant species. The results of metal extraction with chelates showed that EDDS was more efficient at solubilizing Cu and Zn than EDTA, and that EDTA was better at solubilizing Pb and Cd than EDDS.     

Investigation of acute toxicity of cadmium chloride (CdCl2 . H2O) metal salt and behavioral changes it causes on water frog (Rana ridibunda Pallas, 1771)

The 96-h LC(50) value of cadmium chloride (CdCl(2).H(2)O), a metal salt widely used in industry, was determined in the water frog (Rana ridibunda Pallas, 1771). The experiments were conducted in two series and a total of 140 frogs were used to determine acute toxicity. In addition, behavioral changes in the water frog were determined for each cadmium chloride concentration. Data obtained from the cadmium chloride investigation were evaluated by using the probit analysis statistical method and the 96 h LC(50) value for water frog was estimated to be 51.2 mg/l.     

Enhanced retention of linuron, alachlor and metalaxyl in sandy soil columns intercalated with wood barriers

A study has been made of the effect a reactive barrier made of pine (softwood) or oak (hardwood) wood intercalated in a sandy soil column has on the retention of linuron, alachlor and metalaxyl (pesticides with contrasting physicochemical characteristics). The leaching of pesticides has been carried out under a saturated flow regime and breakthrough curves (BTCs) have been obtained at flow rates of 1 mL min⁻¹ (all pesticides) and 3 mL min⁻¹ (linuron). The cumulative curves in the unmodified soil indicate a leaching of pesticides >80% of the total amount of compound added. After barrier intercalation, linuron leaching decreases significantly and a modification of the leaching kinetics of alachlor and metalaxyl has been observed. The theoretical R factors increased ∼2.6-3.3, 1.2-1.6-fold, and 1.4-1.7-fold and the concentration of the maximum peak decreased ∼6-12-fold, 2-4-fold and 1.2-2-fold for linuron, alachlor and metalaxyl, respectively. When considering the three pesticides, significant correlations have been found between the theoretical retardation factor (R) and the pore volume corresponding to the maximum peaks of the BTCs (r = 0.77; p < 0.05) or the total volume leached (r = −0.78; p < 0.05). The results reveal the efficacy of reactive wood barriers to decrease the leaching of pesticides from point sources of pollution depends on the type of wood, the hydrophobicity of the pesticide and the adopted water flow rate. Pine was more effective than oak in decreasing the leaching of hydrophobic pesticide linuron or in decreasing the maximum peak concentration of the less hydrophobic pesticides in soils. Efficacy of these wood barriers was limited for the least hydrophobic pesticide metalaxyl.     

Evaluation of Beta‐naphthoxyacetic Acid for Mutagenic Activity in the Salmonella/mammalian Microsome Assay

1,3‐β‐d‐Glucan derived from baker's yeast was chemically modified in two steps yielding crosslinked carboxymethyl glucan as the sodium salt (2). After cation exchange with hexadecyltrimethylammonium chloride, a hydrophobic adsorbent (3) was obtained which showed an excellent binding of the estrogenic mycotoxin zearalenone with a maximum adsorption of up to 183 mg/g. Compound 3 additionally showed a relatively high adsorption capacity for the trichothecene T‐2 toxin of at least 10 mg/g. Starting from 2, various derivatives were prepared by cation exchange using quaternary ammonium salts bearing substituents besides methyl from four to 18 carbon atoms. The adsorption of T‐2 toxin on these derivatives were compared with compound 3 leading to the conclusion that 3 is the best adsorbent of all investigated tetraalkylammonium‐modified derivatives of 2.     

Reductive dechlorination of chlorinated methanes in cement slurries containing Fe(II)

Degradative solidification/stabilization (DS/S) is a novel remediation technology that combines chemical degradation with conventional solidification/stabilization. The applicability of the Fe(II)-based DS/S to treating chlorinated alkanes was tested by characterizing degradation reactions of carbon tetrachloride (CT) and its daughter products in cement slurries containing Fe(II). Degradation kinetics of CT and chloroform (CF) were generally very rapid with reaction rates comparable to rates that can be obtained with zero-valent iron. Dechlorination reactions of CT proceeded primarily via a hydrogenolysis pathway, which yielded CF and methylene chloride (MC) as major products and chloromethane and methane as minor products. However, reaction pathways other than hydrogenolysis also appeared to be important at very high pH conditions. MC apparently was resistant to dechlorination reactions over a period of about two months. Kinetics of CT and CF transformation were strongly dependent on pH with an optimal value around 13, which was higher than found previously for PCE. When the initial CF concentration varied between 0.01 and 1 mM, and the Fe(II) dose was 104 mM, pseudo-first-order kinetics generally described the degradation reactions of CF. However, there was also some indication of substrate saturation kinetics in these experiments. This suggests that a saturation model would better describe the kinetics in systems with higher concentration of substrates or lower concentration of the reactive surfaces.     

Mixing and transformation of Asian dust with pollution in the two dust storms over the northern China in 2006

To study the mixing and transformation of Asian dust with pollution in the two dust storms over the northern China in 2006, both TSP and PM_2.5 samples were collected at three sites of northern China in addition to the dry deposition samples collected in an episode in Beijing. 23 elements, 15 ions, and 16 PAHs in each sample were analyzed. The two dust storms in northern China were observed in April 8–10 (DS1) and April 16–18 (DS2). Compared to DS2, DS1 was weaker and more polluted with stronger mixing between crustal and pollutant aerosols during their long-range transport. The concentrations of pollution species, e.g. pollution elements, ions, and PAHs were higher in DS1 than that in DS2, while the crustal species showed adverse variation. The correlation between chemical species and Al and between PAH(4) and PAH(5,6) further confirmed the stronger chemical transformation and aerosol mixing in DS1 than that in DS2. Back trajectory and chemical analysis revealed that in DS1 the air masses at Beijing were mostly from southern or southwestern direction at lower altitude with much more pollution, while in DS2 the air masses were mostly from the northwestern and northern direction with dust mainly, which explained why there was a stronger mixing of dust with pollution aerosol in DS1 than that in DS2 over Beijing.     

Conditioning of aluminium-based water treatment sludge with Fenton's reagent: effectiveness and optimising study to improve dewaterability

Alternative conditioning of aluminium-based drinking water treatment sludge using Fenton reagent (Fe2+/H2O2) was examined in this study. Focuses were placed on effectiveness and factors to affect such novel application of Fenton process. Experiments have demonstrated that considerable improvement of alum sludge dewaterability evaluated by capillary suction time (CST) can be obtained at the relative low concentrations of Fenton reagent. A Box-Behnken experimental design based on the response surface methodology was applied to evaluate the optimum of the influencing variables, i.e. iron concentration, hydrogen peroxide concentration and pH. The optimal values for Fe2+, H2O2, and pH are 21 mg g(-1)DS(-1)(dry solids), 105 mg g(-1)DS(-1) and 6, respectively, at which the CST reduction efficiency of 48+/-3% can be achieved, this agreed with that predicted by an established polynomial model in this study.     

Fenuron sorption on homoionic natural and modified smectites

The adsorption isotherms of fenuron (1,1-dimethyl-3-phenylurea) on three smectites (SWy and SAz montmorillonites and SH hectorite) differing in their layer charge (SH相似文献   

Effects of organic fertilizers on soil physicochemistry and on the yield and botanical composition of forage over 3 years

Organic wastes have been reported to reduce saturation of the exchange complex by Al in Al-rich acid soils. For 3 years, the main soil fertility properties were studied in plots sown with mixed pasture species. These plots were fertilized with cattle slurry, dairy sludge (DS), or granulated broiler litter (BL) in comparison with mineral fertilizer. Al saturation levels were low after the initial inorganic liming treatment (19.00-33.71%) but tended to rise under all treatments (21.09-61.37%) except BL (8.45-30.98%), which was also associated with the highest average soil pH and the highest average levels of exchangeable Ca2+, Mg2+, and K+. Treatment DS performed similarly to mineral fertilizer in most respects, but it led to greater available P levels. Under the dry conditions of the second and third years of the study, BL and DS treatments were associated with significantly greater forage yields than the other treatments. Under DS treatment, available P levels were too low to allow the maintenance of mixed pasture, clover being eliminated by the less P-dependent species.     

Histopathological alterations of white seabass,Lates calcarifer,in acute and subchronic cadmium exposure

Histopathological alterations to white seabass, Lates calcarifer aged 3 months in acute and subchronic cadmium exposure were studied by light and scanning electron microscopy. The 96-h LC50 values of cadmium to L. calcarifer was found to be 20.12 +/- 0.61 mg/l and the maximum acceptable toxicant concentration (MATC) was 7.79 mg/l. Fish were exposed to 10 and 0.8 mg/l of Cd (as CdCl,H2O) for 96 h and 90 days, respectively. The study showed that gill lamellae and kidney tubules were the primary target organs for the acute toxic effect of cadmium while in the subchronic exposure, the toxic effect to gills was less than that of kidney and liver. Gill alterations included edema of the epithelial cells with the breakdown of pillar cell system, aneurisms with some ruptures, hypertrophy and hyperplasia of epithelial and chloride cells. The liver showed blood congestion in sinusoids and hydropic swelling of hepatocytes, vacuolation and dark granule accumulation. Lipid droplets and glycogen content were observed in hepatocytes at the second and third month of subchronic exposure. The kidney showed hydropic swelling of tubular cell vacuolation and numerous dark granule accumulation in many tubules. Tubular degeneration and necrosis were seen in some areas.     

Photoelectrocatalytic degradation of 4-chlorophenol and oxalic acid on titanium dioxide electrodes

Photocatalytically active thin TiO(2) films were produced by spin-coating or dip-coating an alkoxy precursor onto a transparent conducting electrode substrate and by thermal oxidation of titanium metal. The thin films were used to study the photoelectrocatalytic or photoelectrochemical degradation of oxalic acid and 4-chlorophenol (4-CP) under near UV (monochromatic, 365 nm) light irradiation. Degradation was monitored by a variety of methods. In the course of oxalic acid degradation, CO(2) formation accounted for up to 100% of the total organic carbon degradation for medium starting concentrations; for the degradation of 4-CP, less CO(2) was detected due to the higher number of oxidation steps, i.e. intermediates. Incident-photon-to-current conversion efficiency, educt degradation and product formation as well as Faradaic efficiencies were calculated for the degradation experiments. Quantum yields and Faradaic efficiencies were found to be strongly dependent on concentration, with maximum values (quantum yield) around 1 for the highest concentrations of oxalic acid.     

Investigation of microplastic pollution on paddy fields in Xiangtan City,Southern China

Microplastics (MPs) have become a hot issue of environmental pollution. However, insufficient evidence exists regarding the distributions and fates of MPs in terrestrial environment, especially in farmlands. The distributions of MPs in paddy fields were investigated in Xiangtan City, a typical rice production area in China. The abundance of MPs in paddy seedling raising fields was 3805?±?511 n·kg^?1, which increased by approximately 9 times than that in common paddy fields. Transparent films became the dominant forms due to the huge usage of mulching films, corresponding to that the proportion of polyvinyl chloride (PVC) increased to 17% there. Moreover, an industrial plant nearby also contributed considerably to the MP pollution; the proportion of PVC (33%) in the paddy fields nearby increased to approximately 4 times of common paddy fields, while polyvinyl alcohol (PVA; 13%) used as an important chemical raw material to synthesis in various applications was uniquely detected there. These results highlight the input of MPs from agricultural and industrial activities in farmlands. Their contributions to the MP pollution in farmlands should be continuously investigated.

     

Enhanced removal of heavy metals in primary treatment using coagulation and flocculation.

The goal of this study was to determine the removal efficiencies of chromium, copper, lead, nickel, and zinc from raw wastewater by chemically enhanced primary treatment (CEPT) and to attain a total suspended solids removal goal of 80%. Operating parameters and chemical doses were optimized by bench-scale tests. Locally obtained raw wastewater samples were spiked with heavy metal solutions to obtain representative concentrations of metals in wastewater. Jar tests were conducted to compare the metals removal efficiencies of the chemical treatment options using ferric chloride, alum, and anionic polymer. The results obtained were compared with those from other studies. It was concluded that CEPT using ferric chloride and anionic polymer is more effective than CEPT using alum for metals removal. The CEPT dosing of 40 mg/L ferric chloride and 0.5 mg/L polymer enhanced heavy metals removal efficiencies by over 200% for chromium, copper, zinc, and nickel and 475% for lead, compared with traditional primary treatment. Efficient metals capture during CEPT can result in increased allowable headworks loadings or lower metal levels in the outfall.     

Fenuron sorption on homoionic natural and modified smectites

Abstract

The adsorption isotherms of fenuron (l, l‐dimethyl‐3‐phenylurea) on three smectites (SWy and SAz montmorillonites and SH hectorite) differing in their layer charge (SH<SWy<SAz) and saturated with several inorganic and organic cations were determined. The isotherms and sorption parameters from Freundlich equation indicate low adsorptivity on inorganic clays, but medium sorption in organoclays (OCls). Fenuron adsorption on homoionic smectites increases with decreasing layer charge and hydratation power of the inorganic exchangeable cation (except Fe³⁺), indicating that fenuron adsorbs as neutral molecule on uncharged siloxane surface by hydrophobic bonding, with some contribution of polar bond (fenuron C=O group and water associated to exchangeable cation). In the case of Fe³⁺‐saturated smectite fenuron protonation, provided by the interlayer acidic environment, promotes further sorption of fenuron as cationic form. The sorption on organoclays is enhanced via hydrophobic interaction with organocations, which is favoured for high layer charge and basal spacing and organocation saturation close to CEC. Quaternary alkylamonium is more efficient in high layer charge smectite, whereas primary alkylammonium is more efficient in medium charge smectite. The low values of the maximum sorption obtained with homoionic inorganic and organic smectites (100 and 5000 μmol/Kg) represent one fenuron molecule for each 2000–200 exchange sites and indicate that fenuron sorption is mainly associated to the outer exchange sites. This low adsorptivity of fenuron, as consequence of its high water affinity (high water solubility) would suggest high mobility of fenuron in natural soil and water systems.