Utilization of urban sewage sludge: Chinese perspectives

Purpose

Urbanization and industrialization in China has resulted in a dramatic increase in the volume of wastewater and sewage sludge produced from wastewater treatment plants. Problems associated with sewage sludge have attracted increasing attention from the public and urban planners. How to manage sludge in an economically and environmentally acceptable manner is one of the critical issues that modern societies are facing.

Methods

Sludge treatment systems consist of thickening, dewatering, and several different alternative main treatments (anaerobic digestion, aerobic digestion, drying, composting, and incineration). Agricultural application, landfill, and incineration are the principal disposal methods for sewage sludge in China. However, sewage sludge disposal in the future should focus on resource recovery, reducing environmental impacts and saving economic costs.

Results

The reuse of biosolids in all scenarios can be environmentally beneficial and cost-effective. Anaerobic digestion followed by land application is the preferable options due to low economic and energy costs and material reuse.

Conclusion

It is necessary to formulate a standard suitable for the utilization of sewage sludge in China.     

Assessing the removal of pharmaceuticals and personal care products in a full-scale activated sludge plant

Purpose

This study aimed to investigate the removal mechanisms of pharmaceutical active compounds (PhACs) and musks in a wastewater treatment plant (WWTP). Biological removal and adsorption in the activated sludge tank as well as the effect of UV radiation used for disinfection purposes were considered when performing a mass balance on the WWTP throughout a 2-week sampling campaign.

Methods

Solid-phase extraction (SPE) was carried out to analyse the PhACs in the influent and effluent samples. Ultrasonic solvent extraction was used before SPE for PhACs analysis in sludge samples. PhAC extracts were analysed by LC-MS. Solid-phase microextraction of liquid and sludge samples was used for the analysis of musks, which were detected by GC-MS. The fluxes of the most abundant compounds (13 PhACs and 5 musks) out of 79 compounds studied were used to perform the mass balance on the WWTP.

Results

Results show that incomplete removal of diclofenac, the compound that was found in the highest abundance, was observed via biodegradation and adsorption, and that UV photolysis was the main removal mechanism for this compound. The effect of adsorption to the secondary sludge was often negligible for the PhACs, with the exceptions of diclofenac, etofenamate, hydroxyzine and indapamide. However, the musks showed a high level of adsorption to the sludge. UV radiation had an important role in reducing the concentration of some of the target compounds (e.g. diclofenac, ibuprofen, clorazepate, indapamide, enalapril and atenolol) not removed in the activated sludge tank.

Conclusions

The main removal mechanism of PhACs and musks studied in the WWTP was most often biological (45%), followed by adsorption (33%) and by UV radiation (22%). In the majority of the cases, the WWTP achieved >75% removal of the most detected PhACs and musks, with the exception of diclofenac.     

Heavy metals in untreated/treated urban effluent and sludge from a biological wastewater treatment plant

Background, Aim and Scope

The presence of heavy metals in wastewater is one of the main causes of water and soil pollution. The aim of the present study was to investigate the removal of Cd, Cu, Pb, Hg, Mn, Cr and Zn in urban effluent by a biological wastewater treatment, as well as to quantify the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sn, Tl, V and Zn in dewatering sludge from the Biological Wastewater Treatment Plant to Ribeirão Preto (RP-BWTP), Brazil.

Materials and Methods

Concentrations of Cd, Cr, Cu, Mn and Pb in wastewater and those of Ni in sludge were determined by atomic absorption spectrophotometry with graphite furnace atomization. Mercury concentrations in wastewater were measured by hydride generation atomic spectrophotometry, and Zn levels were determined by atomic absorption spectrophotometry using acetylene flame. In sludge, the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Pb, Sn, Tl, V and Zn were determined by inductively coupled plasma-mass spectrometry.

Results

The percentages of removal efficiency (RE) were the following: Hg 61.5%, Cd 60.0%, Zn 44.9%, Cu 44.2%, PB 39.7%, Cr 16,5% and Mn 10.4%. In turn, the mean concentrations (mg/kg) of metals in dewatering sludge followed this increasing order: Tl (<0.03), Hg (0.31), Be (0.43), As (1.14), Cd (1.34), V (59.2), Pb (132.1), Sn (166.1), Cr (195.0), Mn (208.1), Ni (239.4), Cu (391.7), Zn (864.4) and Fe (20537).

Discussion

The relationship between metal levels in untreated wastewater, as well as the removal efficiency are in agreement with previous data from various investigators, It is important to note that metal removal efficiency is not only affected by metal ion species and concentration, but also by other conditions such as operating parameters, physical, chemical, and biological factors.

Conclusions

Metal values recorded for treated wastewater and sludge were within the maximum permitted levels established by the Environmental Sanitation Company (CETESB), São Paulo, Brazil.

Recommendations

There is an urgent need for the authorities who are responsible for legislation on sludge uses in agriculture of establishing safety levels for As, Be, Hg, Sn, Tl and V.

Perspectives

According to the current metal levels, RP-BWTP sludge might be used for agriculture purposes. However, for an environmentally safe use of sewage sludge, further studies including systematic monitoring are recommended. Annual metal concentrations and predicted variations of those elements in the sludge should be monitored.

     

Occurrence and distribution of selected pharmaceuticals and personal care products in aquatic environments: a comparative study of regions in China with different urbanization levels

Purpose

We analyzed and compared the distributions of 13 target pharmaceuticals in different water samples from the Hangzhou metropolitan area and Linan County, Southeast China.

Methods

Sampling was conducted in five hospitals, two wastewater treatment plants (WWTPs), and Qiantang River. Samples were concentrated by solid-phase extraction and PPCP concentrations were determined by UPLC-MS/MS.

Results and discussion

Trimethoprim, erythromycin A dihydrate, norfloxacin, ofloxacin, diclofenac sodium, and atenolol were the most frequently detected pharmaceuticals in hospital effluents. Most of the pharmaceutical concentrations in hospital effluents were higher than those in the WWTP influents. Although both WWTPs adopt the anaerobic?Caerobic?Canoxic treatment process, the removal rates for pharmaceuticals, such as trimethoprim and diclofenac sodium, were completely different. Meanwhile, erythromycin A dihydrate, ofloxacin, penicillin-G, cephalexin, cefazolin, ibuprofen, and diclofenac sodium were detected in Qiantang River.

Conclusions

These results indicate that hospitals are more concentrated sources of pharmaceuticals than WWTPs, and the WWTPs are not the only route of entry of pharmaceuticals into aquatic environments in these two regions.     

Use of inorganic wastes as immobilizing agents for soluble P in green waste-based composts

Purpose

The study examines the effectiveness of red mud, blast furnace (BF) slag, and alum-derived water treatment sludge as immobilizing agents for excessive soluble P that had accumulated in three green waste-based composts.

Methods

The three wastes were applied at 0%, 5%, 10%, and 20% w/w to three different composts, all containing extremely high concentrations of extractable P, and were incubated for 60?days. Water-soluble P was measured regularly throughout the incubation period, and at the end, P extractable with resin, 0.05?M NaHCO₃, and 0.005?M H₂SO₄ were also measured.

Results

In the water extracts, inorganic P made up more than 85% of the total P present. All three materials had the ability to adsorb P and thus lowered water-soluble P concentrations. Water treatment sludge was clearly the most effective material, and this was attributed to its amorphous nature (thus, large Brunauer?CEmmett?CTeller surface area) and its acid pH (6.8) compared with the alkaline pH (10?C11) of the other two materials. Water treatment sludge was also the most effective at lowering resin- and NaHCO₃-extractable P. When H₂SO₄ was used as the extractant, BF slag tended to be the most effective material at lowering extractable P, followed by water treatment sludge, and red mud. That is, the P immobilized by water treatment sludge was extractable with acid but not with water, resin, or NaHCO₃.

Conclusions

Water treatment sludge has the potential to be used as an effective immobilizing agent for soluble P in composts, and it should be trialed under field conditions.     

BOD biosensors for pulp and paper industry wastewater analysis

Introduction

Two semi-specific microbial biosensors were constructed for the analysis of biochemical oxygen demand (BOD) in high-cellulose-content pulp and paper industry wastewaters. The biosensors were based on living cells of Bacillus subtilis and Paenibacillus sp. immobilized in an agarose gel matrix. Semi-specific microorganisms were isolated from various samples (decaying sawdust and rabbit manure) and were chosen based on their ability to assimilate cellulose.

Materials &; methods

The biosensors were calibrated with the Organization for Economic Cooperation and Development synthetic wastewater, and measurements with different wastewaters were conducted.

Results

The response time of biosensors using the steady-state method was 20?C25 min, and the service life of immobilized microorganisms was 96 days. Detection limit was 5 mg/l of BOD₇ while linear ranges extended up to 55 and 50 mg/l of the BOD₇ for B. subtilis- and Paenibacillus sp.-based biosensors, respectively. Repeatability and reproducibility of both biosensors were within the limits set by APHA??less than 15.4%. In comparison, both biosensors overestimated the BOD₇ values in paper mill wastewaters and underestimated the BOD₇ in aspen pulp mill wastewater.

Conclusions

The semi-specific biosensors are suitable for the estimation of organic pollution derived from cellulose, while the detection of pollution derived from tannins and lignins was minor. Better results in terms of accuracy and repeatability were gained with Paenibacillus sp. biosensor.     

Occurrence of endocrine disrupters and selected pharmaceuticals in Aisonas River (Greece) and environmental risk assessment using hazard indexes

Purpose

The presence of four phenolic endocrine disrupting compounds (EDCs: nonylphenol [NP], NP monoethoxylate[NP1EO], bisphenol A [BPA], triclosan, [TCS]) and four nonsteroidal anti-inflammatory drugs (NSAIDs: ibuprofen[IBF], ketoprofen [KFN], naproxen [NPX], diclofenac [DCF]) in a Greek river receiving treated municipal wastewater was investigated in this study.

Methods

Samples were taken from four different points of the river and from the outlet of a sewage treatment plant (STP) during six sampling campaigns, and they were analyzed using gas chromatography?Cmass spectrometry.

Results

According to the results, EDCs were detected in almost all samples, whereas NSAIDs were detected mainly in wastewater and in the part of the river that receives wastewater from the STP. Among the target compounds, the highest mean concentrations in the river were detected for NP (1,345?ng?L^?1) and DCF (432?ng?L^?1). Calculation of daily loads of the target compounds showed that STP seems to be the major source of NSAIDs to the river, whereas other sources contribute significantly to the occurrence of EDCs. The environmental risk due to the presence of target compounds in river water was estimated, calculating risk quotients for different aquatic organisms (algae, daphnids, and fish). Results denoted the possible threat for the aquatic environment due to the presence of NP and TCS in the river.     

Changes in toxicity and genotoxicity of industrial sewage sludge samples containing nitro- and amino-aromatic compounds following treatment in bioreactors with different oxygen regimes

Goals, Scope and Background

From 2005, deposition of organic waste will be banned in Sweden. Likewise, in Germany and Austria, similar bans are being planned, and further countries will probably follow. Thus, there is a need to develop new methods and to refine established techniques for sludge management in the whole of the European Union. For this end, there is also an urgent need for appropriate ecotoxicological approaches to elucidate and assess the hazard potential of sewage sludge. Therefore, the present study was designed to assess the capacity of various established sludge treatment methods using different oxygen regimes to degrade recalcitrant nitro-substituted organic compounds and reduce their toxicity. Sewage sludge samples from a wastewater treatment plant in Sweden (Cambrex Karlskoga AB, industrial area Björkborn) receiving wastewater from industries manufacturing pharmaceutical substances, chemical intermediates and explosives were processed with different sludge treatment methods. Among other treatment methods, bioreactors (for anaerobic and aerobic sludge treatment) were used. In the present investigation, a battery ofin vitro bioassays was employed to compare the cytotoxic and genotoxic potentials of different fractions of sludge samples in order to elucidate whether the treatments were suitable to reduce the toxicity of the sludge.

Methods

In order to investigate the cytotoxicity of the extracts of treated and untreated sludge samples, the acute cytotoxicity test with the permanent cell line RTL-W1 was used. Genotoxicity was tested by means of the comet assay (single cell gel electro-phoresis) with RTL-W1cells, and mutagenicity was assessed with the Ames test using the Salmonella typhimurium strains TA98, TA98NR and TA100. Sludge toxicity was tested in different fractions of organic extracts produced by acetone and hexane extractions. The subsequent clean-up procedure (silica gel chro-matography and elution with hexane and dichloromethane) resulted in two fractions, a lipophilic hexane-fraction and a semi-lipophilic dichloromethane-fraction. For the genotoxicity and mutagenicity tests, these fractions were reunited at equal ratios.

Results and Discussion

The acute cytotoxicity test with RTL-Wl cells revealed a high cytotoxic potential for the semi-li-pophilic DM-fractions of all sludge samples with NR₅₀ values (= effective concentration for 50% cell death in the neutral red test) from 8.9 up to 20 mg sludge d.w./ml medium. A low cytotoxic potential for the hexane fractions of the untreated sludge samples (NR₅₀ 400 to < 400 mg sludge d.w./ml medium) was observed, whereas the hexane fractions of the treated sludge samples showed elevated cytotoxicity increasing further with treatment in the bioreactors. The comet assay indicated that three out of eight of the reunited fractions had a significant genotoxic potential. Whereas the genotoxic potential of one sample treated anaerobically was very high with an induction factor of 11.6, a similar sample (taken from the same anaerobic reactor four months later) and one untreated sample showed lower potentials. The samples treated in another anaerobic bioreactor as well as the samples treated aerobically showed no genotoxic potential. Results indicate that aerobic treatment was basically adequate for reducing the genotoxicity of the sludge, whereas anaerobic treatment was only partly useful for reduction of genotoxicity. The Ames test revealed a very high mutagenic potential for the reunited fractions of the untreated sludge samples with strain TA98 (maximum induction factors (IF_max up to 45) and a relatively high potential for one of the samples treated aerobically (S2, IF_max = 18 (TA98, S9-)), thus documenting the suitability of both anaerobic and aerobic treatments to reduce the mutagenicity of the samples, however, with the aerobic treatment being less effective. Conclusions. Overall, none of the microbiological treatments for wastewater sludge in bioreactors was found to be ideal for general toxicity reduction of the sludge samples. Whereas cytotoxicity of the sludge increased or levelled off in most cases following either treatment, genotoxicity both increased or decreased after anaerobic treatment, depending on the specific sample. However, mutagenicity could generally be reduced by anaerobic treatment and, to a lesser degree, by aerobic treatment. Recommendationsand Perspectives. The complex modification of the diverse damage potentials of sludge sample extracts by use of anin vitro biotest battery following treatment for toxicity reduction in bioreactors showed that considerations of different toxicological endpoints is essential for an adequate hazard assessment. Whereas in the case of cytotoxicity reduction, the reactors proved ineffective, mutagenicity could be reduced significantly at least in some cases in this case study.

     

A preliminary investigation of the environmental impact of a thermal power plant in relation to PCB contamination

Purpose

The most significant application of polychlorinated biphenyls (PCBs) is in transformers and capacitors. Therefore, power plants are important suspected sources for entry of PCBs into the environment. In this context, the levels and distribution of PCBs in sediment, soil, ash, and sludge samples were investigated around Seyitömer thermal power plant, Kütahya, Turkey. Moreover, identity and contribution of PCB mixtures were predicted using the chemical mass balance (CMB) receptor model.

Methods

United States Environmental Protection Agency methods were applied during sample preparation, extraction (3540C), cleanup (3660B, 3665A, 3630C), and analysis (8082A).

Results

ΣPCB concentrations in the region ranged from not detected to 385 ng/g dry weight, with relatively higher contamination in sediments in comparison to soil, sludge, and ash samples collected from around the power plant. Congener profiles of the sediment and soil samples show penta-, hexa-, and hepta-chlorobiphenyls as the major homolog groups. The results from the CMB model indicate that PCB contamination is largely due to Clophen A60/A40 and Aroclor 1254/1254(late)/1260 release into the sediment and sludge samples around the thermal power plant.

Conclusions

Since there are no other sources of PCBs in the region and the identity of PCB sources estimated by the CMB model mirrors PCB mixtures contained in transformers formerly used in the plant, the environmental contamination observed especially in sediments is attributed to the power plant. Release of PCBs over time, as indicated by the significant concentrations observed even in surface samples, emphasizes the importance of the need for better environmental management.

     

Improvement of biodegradability of PVA-containing wastewater by ionizing radiation pretreatment

Background

Polyvinyl alcohol (PVA) has been widely used as sizing agents in textile and manufacturing industry, and it is a refractory compound with low biodegradability.

Objective

The objective of this paper was to treat the PVA-containing wastewater using gamma irradiation as a pretreatment strategy to improve its biodegradability and to determine the roles of different kinds of radical species played during pretreatment.

Methods

Gamma radiation was carried out in a ⁶⁰Cobalt source station, PVA concentration was analyzed by using a visible spectrophotometer and specific oxygen uptake rate (SOUR, milligram of O₂ per gram of mixed liquor volatile suspended solids (MLVSS) per hour) was measured by a microrespirometer.

Results

The results showed that the biodegradability of PVA-containing wastewater with low initial concentration (e.g., 327.8?mg/l) could be improved greatly with increasing irradiation dose. However, PVA gel formation was observed at higher initial PVA concentration (e.g., 3,341.6?mg/l) and higher irradiation dose, which inhibited PVA degradation by aerobic microorganisms. However, the formed gel could be separated by microfiltration, which led to more than 90% total organic carbon (TOC) removal.

Conclusion

Ionizing radiation could be used as a pretreatment technology for PVA-containing wastewater, and its combination with biological process is feasible.     

Bioremediation of acidic oily sludge-contaminated soil by the novel yeast strain Candida digboiensis TERI ASN6

Background, aim, and scope

Primitive wax refining techniques had resulted in almost 50,000 tonnes of acidic oily sludge (pH 1–3) being accumulated inside the Digboi refinery premises in Assam state, northeast India. A novel yeast species Candida digboiensis TERI ASN6 was obtained that could degrade the acidic petroleum hydrocarbons at pH 3 under laboratory conditions. The aim of this study was to evaluate the degradation potential of this strain under laboratory and field conditions.

Materials and methods

The ability of TERI ASN6 to degrade the hydrocarbons found in the acidic oily sludge was established by gravimetry and gas chromatography–mass spectroscopy. Following this, a feasibility study was done, on site, to study various treatments for the remediation of the acidic sludge. Among the treatments, the application of C. digboiensis TERI ASN6 with nutrients showed the highest degradation of the acidic oily sludge. This treatment was then selected for the full-scale bioremediation study conducted on site, inside the refinery premises.

Results

The novel yeast strain TERI ASN6 could degrade 40 mg of eicosane in 50 ml of minimal salts medium in 10 days and 72% of heneicosane in 192 h at pH 3. The degradation of alkanes yielded monocarboxylic acid intermediates while the polycyclic aromatic hydrocarbon pyrene found in the acidic oily sludge yielded the oxygenated intermediate pyrenol. In the feasibility study, the application of TERI ASN6 with nutrients showed a reduction of solvent extractable total petroleum hydrocarbon (TPH) from 160 to 28.81 g kg^?1 soil as compared to a TPH reduction from 183.85 to 151.10 g kg^?1 soil in the untreated control in 135 days. The full-scale bioremediation study in a 3,280-m² area in the refinery showed a reduction of TPH from 184.06 to 7.96 g kg^?1 soil in 175 days.

Discussion

Degradation of petroleum hydrocarbons by microbes is a well-known phenomenon, but most microbes are unable to withstand the low pH conditions found in Digboi refinery. The strain C. digboiensis could efficiently degrade the acidic oily sludge on site because of its robust nature, probably acquired by prolonged exposure to the contaminants.

Conclusions

This study establishes the potential of novel yeast strain to bioremediate hydrocarbons at low pH under field conditions.

Recommendations and perspectives

Acidic oily sludge is a potential environmental hazard. The components of the oily sludge are toxic and carcinogenic, and the acidity of the sludge further increases this problem. These results establish that the novel yeast strain C. digboiensis was able to degrade hydrocarbons at low pH and can therefore be used for bioremediating soils that have been contaminated by acidic hydrocarbon wastes generated by other methods as well.     

Perfluorooctanoic acid and perfluorooctane sulfonate released from a waste water treatment plant in Bavaria, Germany

Purpose

Perfluorooctanoate (PFOA), perfluorooctane sulfonate (PFOS), and precursors and derivatives thereof have been employed as surfactants and anti-adhesives. PFOA and PFOS are environmentally persistent and the discharge of municipal waste waters is one of the principal routes of these compounds into the aquatic environment. In a previous study, the concentrations of PFOA and PFOS in grab samples collected from the waste water treatment plant (WWTP) of Bayreuth, a city of 72,000 inhabitants in Bavaria, Germany, during two periods showed considerable variability. For a better estimate of average mass flows, the surfactants were monitored (five samplings) from 16 March to 18 May 2007. In a second campaign, river water receiving the WWTP effluent was sampled twice a day for five consecutive days.

Methods

Quantitative analysis was done by stable-isotope dilution, pre-cleaning, and pre-concentration by solid-phase extraction, and liquid chromatography followed by electrospray ionization/tandem mass spectrometry.

Results

The mass flows of PFOA and PFOS through the WWTP were determined. PFOA is fully discharged into the river, while about half of PFOS is retained in the sewage sludge. The average daily mass load of the river Roter Main by the WWTP of Bayreuth is about 1.2?±?0.5 g PFOA and 5?±?2 g PFOS, with variations of up to 140% within one day.

Conclusion

Overall, the total annual release to the rivers of Germany may be in the range of several hundred kilograms of PFOA and several tons of PFOS.     

Effect of particle size of titanium dioxide nanoparticle aggregates on the degradation of one azo dye

Introduction

Titanium dioxide (TiO₂) nanoparticle powders have been extensively studied to quickly photodegrade some organic pollutants; however, the effect of the particle size of TiO₂ nanoparticle aggregates on degradation remains unclear because microscale aggregates form once the nanoparticle powders enter into water.

Methods

The degradation of azo dye by different particle sizes of TiO₂ nanoparticle aggregates controlled by NaCl concentrations was investigated to evaluate the particle size effect. Removal reactions of reactive black 5 (RB5) with TiO₂ nanoparticles followed pseudo-first-order kinetics.

Results

The increase of TiO₂ dosage from 40 to 70?mg/L enhanced the degradation. At doses around 100?mg/L TiO₂, degradation rates decreased which could be the result of poor UV light transmittance at high-particle concentrations. At average particle sizes of TiO₂ nanopowders less than around 500?nm, the degradation rates increased with decreasing particle size. As the average particle size exceeded 500?nm, the degradation rates were not significantly changed.

Conclusions

For the complete degradation experiments, the mineralization rates of total organic carbon disappearance are generally following the RB5 decolorization kinetic trend. These findings can facilitate the application of TiO₂ nanoparticles to the design of photodegradation treatments for wastewater.     

China’s wastewater discharge standards in urbanization

Background and purpose

China's environmental problems and pollution control have global implications. China??s water pollution has been increasing with its urbanization and industrialization. Although great efforts have been taken to keep its wastewater discharge standards in pace with the water pollution development and technological advances, many challenges remain. A summary of the past achievements and lessons as well as the current problems in water pollution may provide a basis for future improvements in China and a reference for other countries.

Methods

Statistical data are summarized to reveal the evolution of China??s population, wastewater discharge and corresponding discharge standards over the past four decades. In particular, the specific control indexes and number of controlled items are discussed in details. The present water pollution situation is clearly illustrated by the water pollution map and the water quality distribution diagram. A comparison between China??s present wastewater discharge standards and those in the USA and the EU are also presented to find the possibilities for future improvement.

Results

The historical origins, major challenges and future perspectives of China??s wastewater discharge standards are overviewed. The barriers and ongoing efforts for standards formulation and implementation are highlighted. Some suggestions for future endeavors are given.

Conclusions

China??s wastewater discharge standard system has seen significant improvement over the past decades, but it still has many defects and limitations. Nonetheless, unprecedented great efforts are underway to address all these challenges. More stringent standards and subsequently a cleaner water environment in China can be expected in the near future.     

Occurrence, distribution, and seasonal variation of estrogenic compounds and antibiotic residues in Jiulongjiang River, South China

Background and purpose

Estrogenic compounds and antibiotic residues in environment are receiving significant attention because of their potential adverse effects on ecosystems and human health. The objectives of this study were to determine the occurrence and seasonal variability of eight kinds of estrogenic compounds and 14 antibiotics. The study developed an occurrence database of the estrogenic compounds and antibiotics in spatial and temporal scale in Jiulongjiang River, South China, to provide useful information for environmental management of this region.

Methods

Eight estrogenic compounds and 14 antibiotic compounds were detected in Jiulongjiang River from 19 sampling sites during high-flow and low-flow season in surface water. The samples were preconcentrated by solid-phase extraction for analysis. Eight estrogenic compounds were analyzed by gas chromatography mass spectrometry (Agilent 7890A-5975C), and antibiotics were determined by liquid chromatography-tandem mass spectrometry (LC?CMS/MS) system (ABI 3200 Q TRAP).

Results

All target compounds could be detected, except 17??-ethynylestradiol, sulfamerazine, and ofloxacin. The median concentrations for seven estrogenic compounds ranged from 6.00 to 610.72?ng/L, with the detection frequency range of 16.00?C100%. However, the detection frequencies of 13 antibiotics detected varied from 50% to 100%, with the median concentrations ranged from 0.89 to 117.97?ng/L. Seasonal variations were obvious for most estrogenic compounds in Jiulongjiang River, except for octylphenol and estriol. There were significant (P?Conclusion The Jiulongjiang River water was more seriously contaminated by diethylstilbestrol, estrone, sulfamethazine, and tetracyclines. Higher overall concentration levels of estrogenic compounds and antibiotics were detected in low-flow water than those in high-flow water. The pollution of estrogenic compounds and antibiotics in Jiulongjiang River mainly came from municipal sewage and livestock breeding activities.     

Equilibrium, kinetic and thermodynamic studies on the biosorption of reactive acid dye on Enteromorpha flexuosa and Gracilaria corticata

Purpose

Biosorption is an emerging, eco-friendly and economical method for treating the wastewater effluents. Compared to many other biological materials, algae biomass proved to be the better biosorbent due to the presence of cell wall polymers in them.

Methods

Algal biomasses namely Enteromorpha flexuosa and Gracilaria corticata were dried, crushed and used as biosorbents. Ponceau S, a diazo dye was used as a model adsorbate for the biosorption studies. The biosorbents were characterized by Scanning Electron Microscopy, FT-IR and zero point charge. Batch studies were performed by varying pH, biosorbent dosage and initial dye concentrations. Adsorption isotherms, kinetic and thermodynamic analyses were carried out. The effect of electrolytes was also studied. Batch desorption studies were also carried out using various reagents.

Results

Isotherm data were tested with Langmuir and Freundlich isotherm models and the results suggested that the Freundlich isotherm fitted the data well. Kinetic studies were performed with varying initial dye concentrations and the data were incorporated with pseudo first-order and pseudo second-order kinetic equations and was found that the studied biosorption processes followed pseudo second-order kinetic equation. Thermodynamic parameters were evaluated at three different temperatures 293?K, 300?K and 313?K. About 95% of the dye could be desorbed from both the biosorbents.

Conclusion

Both the algal biomasses had heterogeneous surfaces and followed pseudo second-order chemical kinetics. Thermodynamic parameters proved that the biosorption by both the biomasses were spontaneous, feasible and endothermic processes. Desorption studies proved the worth of the algal biomasses as biosorbents in industrial level.     

Changes in character of organics in the receiving environment of effluent from a sulphite pulp mill

Purpose

The characteristics of organics in sulphite pulp mill effluent and in the receiving environment of effluent discharge were investigated to assess the basis for the persistence or attenuation of colour.

Methods

Characterization of organics was conducted through determination of SUVA, specific colour, and molecular weight distribution of organics using high performance size exclusion chromatography and by solid-state ¹³?C cross polarization (CP) NMR. The characteristics of organics from mill wastewater before and after secondary aerobic treatment, followed by lime treatment and from the receiving environment, an enclosed brackish lake were compared. Changes in the character of organics in lake water over a period of 14?years were studied in the context of changes in mill processing and climate impacts.

Results

High colour in mill effluent and in receiving waters correlated with high SUVA and specific colour levels, high molecular weight range and aromatic content. Conversely, lake waters with low colour had UV absorbing compounds of much lower molecular weight range and low relative abundance of aromatic compounds. Attenuation of colour and changes in the character of organics in the receiving environment coincided with increased concentrations of metal cations.

Conclusions

These increased concentrations appear to be due to the effects of climate change, lake management and their presence in mill effluent, with subsequent discharge to the lake. Attenuation of colour was found to be predominantly through removal of high molecular weight aromatic compounds where the removal processes could be through adsorption and co-precipitation with divalent metals, as well as through dilution processes.     

Evolutions of microbial degradation pathways for parent xenobiotic and for its metabolites follow different schemes

Background and purposes

The pathways used by microorganisms for the metabolism of every xenobiotic substrate are specific. The catabolism of a xenobiotic goes through a series of intermediate steps and lower intermediates (metabolites) appear in sequence. The structure of the metabolites can be similar to the parents due to kinship. The purposes of this study were to examine if the degradation pathways that were developed for a parent xenobiotic are effective to degrade the parent??s lower metabolites, and if the reverse is true.

Materials and methods

The xenobiotic substrates, 2,4-dichlorophenoxyacetic acid (2,4-D, the parent xenobiotic) and its metabolite 2,4-dichlorophenol (2,4-DCP), were independently subjected to acclimation and degradation tests by the biomasses of mixed-culture activated sludge and a pure culture of Arthrobacter sp.

Results

Activated sludge and Arthrobacter sp. that were acclimated to 2,4-D effectively degraded 2,4-D and the lower metabolites of 2,4-D, typically 2,4-DCP. During the degradation of 2,4-D, accumulations of the lower metabolites of 2,4-D were not found. The degradation pathways acquired from acclimation to 2,4-D are effective for all the metabolites of 2,4-D. However, pathways acquired from acclimation to 2,4-DCP are not effective in the degradation of the parent 2,4-D.

Conclusions

Microorganisms acclimated to 2,4-D evolve their degradation pathways by a scheme that is different from the scheme the microorganisms employ when they are acclimated to the metabolites of 2,4-D.     

Copper and cadmium removal from synthetic industrial wastewater using chitosan and nylon 6

Purpose

Chitosan with nylon 6 membranes was evaluated as adsorbents to remove copper and cadmium ions from synthetic industrial wastewater.

Methods

Chitosan and nylon 6 with glutaraldehyde blend ratio with (1:1+Glu, 1:2+Glu, and 2:1+Glu) have been prepared and these were used as membranes to remove copper and cadmium ions from synthetic industrial wastewater. Characterization of the synthesized membrane has been done with FTIR, XRD, TGA/DTA, DSC, and SEM. Chemical parameters for quantities of adsorption of heavy metal contamination have been done and the kinetics of adsorption has also been carried out.

Results

The optimal pH for the removal of Cd(II) and Cu(II) using chitosan with nylon 6. Maximum removal of the metals was observed at pH 5 for both the metals. The effect of adsorbent dose also has a pronounced effect on the percentage of removal of the metals. Maximum removal of both the metals was observed at 5 g/100 ml of the adsorbent.

Conclusion

Copper and cadmium recovery is parallel at all time. The percentage of removal of copper increased with increase in the pH from 3 to 5. In the case of cadmium containing wastewater, the maximum removal of metal occurred at pH 5. The uptake amount of Cu²⁺ ions on chitosan increased rapidly with increasing contact time from 0 to 360 min and then reaches equilibrium after 360 min; the equilibrium constant for copper and cadmium ions is more or less the same for the adsorption reaction.     

Characterization of PM10 atmospheric aerosol at urban and urban background sites in Fuzhou city, China

Background

PM₁₀ aerosol samples were simultaneously collected at two urban and one urban background sites in Fuzhou city during two sampling campaigns in summer and winter. PM₁₀ mass concentrations and chemical compositions were determined.

Methods

Water-soluble inorganic ions (Cl^?, NO ₃ ^? , SO ₄ ^2? , NH ₄ ⁺ , K⁺, Na⁺, Ca²⁺, and Mg²⁺), carbonaceous species (elemental carbon and organic carbon), and elements (Al, Si, Mg, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Br, and Pb) were detected using ion chromatography, thermal/optical reflectance, and proton-induced X-ray emission methods, respectively.

Results

PM₁₀ mass concentrations, as well as most of the chemical components, were significantly increased from urban background to urban sites, which were due to enhanced anthropogenic activities in urban areas. Elements, carbonaceous species, and most of the ions were more uniformly distributed at different types of sites in winter, whereas secondary ion SO ₄ ^2? , NO ₃ ^? , and NH ₄ ⁺ showed more evident urban-background contrast in this season. The chemical mass closure indicated that mineral dust, organic matters, and sulfate were the most abundant components in PM₁₀. The sum of individually measured components accounted for 86.9?C97.7% of the total measured PM₁₀ concentration, and the discrepancy was larger in urban area than in urban background area.

Conclusion

According to the principal component analysis?Cmultivariate linear regression model, mineral dust, secondary inorganic ions, sea salt, and motor vehicle were mainly responsible for the PM₁₀ particles in Fuzhou atmosphere, and contributed 19.9%, 53.3%, 21.3%, and 5.5% of PM₁₀, respectively.