Biodegradation of Agricultural Plastic Films: A Critical Review

The growing use of plastics in agriculture has enabled farmers to increase their crop production. One major drawback of most polymers used in agriculture is the problem with their disposal, following their useful life-time. Non-degradable polymers, being resistive to degradation (depending on the polymer, additives, conditions etc) tend to accumulate as plastic waste, creating a serious problem of plastic waste management. In cases such plastic waste ends-up in landfills or it is buried in soil, questions are raised about their possible effects on the environment, whether they biodegrade at all, and if they do, what is the rate of (bio?)degradation and what effect the products of (bio?)degradation have on the environment, including the effects of the additives used. Possible degradation of agricultural plastic waste should not result in contamination of the soil and pollution of the environment (including aesthetic pollution or problems with the agricultural products safety). Ideally, a degradable polymer should be fully biodegradable leaving no harmful substances in the environment. Most experts and acceptable standards define a fully biodegradable polymer as a polymer that is completely converted by microorganisms to carbon dioxide, water, mineral and biomass, with no negative environmental impact or ecotoxicity. However, part of the ongoing debate concerns the question of what is an acceptable period of time for the biodegradation to occur and how this is measured. Many polymers that are claimed to be ‘biodegradable’ are in fact ‘bioerodable’, ‘hydrobiodegradable’, ‘photodegradable’, controlled degradable or just partially biodegradable. This review paper attempts to delineate the definition of degradability of polymers used in agriculture. Emphasis is placed on the controversial issues regarding biodegradability of some of these polymers.     

Policy trends of e-waste management in Asia

This paper examines the policy trends of electronic waste (e-waste) management in Asia. E-waste is a rapidly growing waste stream in the world today and is estimated to be growing at 3–5 % per annum. Fast paced obsolescence in the electronic sector has resulted in the generation of e-waste. There are concerns that e-waste generated in developed countries is ending up in developing countries especially in Asia resulting in adverse environmental and health impacts. Consequently, a number of countries in Asia are developing policy instruments to ensure the proper management of e-waste. These include e-waste regulatory frameworks, data and inventories, and infrastructure and capacity building. These trends indicate a positive development path towards sustainable e-waste management in Asia. Nevertheless, potential limiting obstacles for e-waste management in Asia may also include an over-reliance on legislation to drive e-waste management or the simplistic adoption of policies from developed countries without taking into context the local political, cultural and socio-economic waste management issues. Consequently, this paper suggest that e-waste policy development may require a more customized approach where, instead of addressing e-waste in isolation, it should be addressed as part of the national development agenda that integrates green economy assessment and strategic environmental assessment as part of national policy planning. In conclusion, policy trends of e-waste management in Asia appear promising provided there is a paradigm shift from an e-waste perception of an environment problem to a e-waste perception of a potential opportunity as sustainable national green growth strategy in Asia.     

Controlling the Behaviors of Biodegradable/Bioabsorbable Polymers with Cyclodextrins

The cyclic six, seven, and eight-membered oligosaccharides -, -, and -cyclodextrins (CDs) can serve as hosts for a variety of polymer guests to form crystalline inclusion compounds (ICs), wherein the guest polymers are included in the continuous narrow channels (0.5–1.0 nm in diameter) formed by the host CD stacks. Polymers included as guests in CD-ICs are highly extended and segregated from neighboring chains by the walls of the host CD bracelets. As a consequence, when polymer-CD-ICs are treated with solvents for CDs that are non-solvents for the included polymers or with amylase enzymes, the CDs are removed and the guest polymers are coalesced into bulk samples whose structures, morphologies, and even chain conformations are different from those achieved by consolidation from their randomly coiling, entangled solutions and melts. Often these CD-IC coalesced and consequently reorganized polymer samples exhibit properties that are distinct from their normally processed bulk samples. Here we describe the CD-IC processing of several biodegradable/bioabsorbable homopolymers, copolymers, and blends made from poly (L-lactic acid), poly (-caprolactone), and poly (-hydroxybutyrate)s, with special emphasis placed on their improved and controllable properties. For example, the phase segregation and consequent crystallinities of their normally incompatible homopolymer blends and their block copolymers may be controlled and thus improved. In addition, co-inclusion of small molecule guests, such as drugs or anti-bacterials, in their common CD-ICs, and subsequent coalescence, yields well-mixed blends of these biodegradable/bioabsorbable polymers and the small molecule co-guests, which may lead, for example, to the improved delivery of drugs.     

Characterization of Biodegradable Polymer Blends of Acetylated and Hydroxypropylated Sago Starch and Natural Rubber

Development of biodegradable polymers from absolute environmental friendly materials has attracted increasing research interest due to public awareness of waste disposal problems caused by low degradable conventional plastics. In this study, the potential of incorporating natural rubber latex (NRL) into chemically modified sago starch for the making biodegradable polymer blends was assessed. Native sago starch was acetylated and hydroxypropylated before gelatinization in preparing starch thermoplastic using glycerol. They were than casted with NRL into biopolymer films according to the ratios of 100.00/0.00, 99.75/1.25, 98.50/2.50, 95.00/5.00, 90.00/10.00 and 80.00/20.00 wt/wt, via solution spreading technique. Water absorption, thermal, mechanical, morphological and biodegradable properties of the product films were evaluated by differential scanning calorimetry (DSC), universal testing machine (UTM), scanning electron microscopy (SEM) and fourier transform infrared spectroscopy. Results showed that acetylation promoted the incorporating behavior of NRL in sago starch by demonstrating a good adhesion characteristic and giving a uniform, homogenous micro-structured surface under SEM observation. However, the thin biopolymer films did not exhibit any remarkable trend in their DSC thermal profile and UTM mechanical properties. The occurrence of NRL suppressed water adsorption capacity and delayed the biodegradability of the biopolymer films in the natural environment. Despite the depletion in water adsorption capacity, all of the product films degraded 50 % within 12 weeks. This study concluded that biopolymers with desirable properties could be formulated by choosing an appropriate casting ratio of the sago starch to NRL with suitable chemical substitution modes.     

Methods Currently Used in Testing Microbiological Degradation and Deterioration of a Wide Range of Polymeric Materials with Various Degree of Degradability: A Review

Biodegradation of polymeric materials affect a wide range of industries, information on degradability can provide fundamental information facilitating design and life-time analysis of materials. Among the methods currently used in testing, traditional gravimetric and respirometric techniques are tailored to readily degradable polymeric materials mostly and polymer blends with biodegradable components, but they are not applicable to the new generation of engineering polymers which are relatively resistant to biodegradation. However, electrochemical impedance spectroscopy (EIS) has been tested for monitoring biodeterioration of high strength materials and the technique has very high sensitivity. A wide range of materials including electronic insulation polyimides, fiber-reinforced polymeric composites (FRPCs) and corrosion protective polyurethane coatings have been successfully measured under inoculation of degradative microorganisms using EIS. In addition, the mechanism of degradation of high strength polymers is mainly due to the presence of plasticizers in the polymer matrices. The information on various methods discussed in this review is intended to illustrate a suite of methods for those who are interested in testing biodeterioration of polymeric materials under different environmental conditions and in selecting appropriate techniques for specific applications.     

Utilization of Waste Lignin and Hydrolysate From Chromium Tanned Waste in Blends of Hot-Melt Extruded PVA-Starch

The demand for biodegradable plastic material is increasing worldwide. However, the cost remains high in comparison with common forms of plastic. Requirements comprise low cost, good UV-stability and mechanical properties, as well as solubility and water uptake lead to the preparation of multi-component polymer blends based on polyvinyl alcohol and starch in combination with waste products that are hard to utilize—waste lignin and hydrolysate extracted from chromium tanned waste. Surprisingly the addition of such waste products into PVA gives rise to blends with better biodegradability than commercial PVA in an aquatic aerobic environment with non-adapted activated sludge. These blends also exhibited greater solubility in the water and UV stability than commercial PVA. Tests on the processing properties of the blends (melt flow index, tensile strength and elongation at break of the films) as well as their mechanical properties showed that materials based on these blends might be applied in agriculture (for example as the systems for controlled-release pesticide or fertilizer) and, somewhat, in the packaging sector.     

Selective separation of virgin and post-consumer polymers (PET and PVC) by flotation method

More and more polymer wastes are generated by industry and householders today. Recycling is an important process to reduce the amount of waste resulting from human activities. Currently, recycling technologies use relatively homogeneous polymers because hand-sorting waste is costly. Many promising technologies are being investigated for separating mixed thermoplastics, but they are still uneconomical and unreliable. At present, most waste polymers cause serious environmental problems. Burning polymers for recycling is not practiced since poisonous gases are released during the burning process. Particularly, polyvinyl chloride (PVC) materials among waste polymers generate hazardous HCl gas, dioxins containing Cl, etc., which lead to air pollution and shorten the life of the incinerator. In addition, they make other polymers difficult to recycle.Both polyethylene terephthalate (PET) and PVC have densities of 1.30–1.35 g/cm³ and cannot be separated using conventional gravity separation techniques. For this reason, polymer recycling needs new techniques. Among these techniques, froth flotation, which is also used in mineral processing, can be useful because of its low cost and simplicity.The main objective of this research is to recycle PET and PVC selectively from post-consumer polymer wastes and virgin polymers by using froth flotation. According to the results, all PVC particles were floated with 98.8% efficiency in virgin polymer separation while PET particles were obtained with 99.7% purity and 57.0% efficiency in post-consumer polymer separation.     

Ecotoxicity Evaluation of the Biodegradable Polymers PLA,PBAT and its Blends Using <Emphasis Type="Italic">Allium cepa</Emphasis> as Test Organism

Biodegradable polymers are considered a feasible option to minimize the environment impacts of high disposal of solid waste. Nevertheless, environmental safety of these materials is a few explored issue. In this context, this study evaluated ecotoxicological effects in soil of the biodegradable materials poly(lactic acid)-PLA, poly(butylene adipate co-terephthalate)-PBAT and their blends compatibilized with a chain extender. The tool used for this analysis was the bioassay with Allium cepa as test organism. The studied materials were not phytotoxic, cytotoxic, genotoxic nor mutagenic for meristematic cells of A. cepa.     

Mechanical and Barrier Properties of Biodegradable Films Made from Chitosan and Poly (Lactic Acid) Blends

Biodegradable film blends of chitosan with poly(lactic acid) (PLA) were prepared by solution mixing and film casting. The main goal of these blends is to improve the water vapor barrier of chitosan by blending it with a hydrophobic biodegradable polymer from renewable resources. Mechanical properties of obtained films were assessed by tensile test. Thermal properties, water barrier properties, and water sensitivity were studied by differential scanning calorimeter analysis, water vapor permeability measurements, and surface-angle contact tests, respectively. The incorporation of PLA to chitosan improved the water barrier properties and decreased the water sensitivity of chitosan film. However, the tensile strength and elastic modulus of chitosan decreased with the addition of PLA. Mechanical and thermal properties revealed that chitosan and PLA blends are incompatible, consistent with the results of Fourier transform infrared (FTIR) analysis that showed the absence of specific interaction between chitosan and PLA.     

Biodegradable Polymers- A Review on Recent Trends and Emerging Perspectives

Recent trends in biodegradable polymers indicate significant developments in terms of novel design strategies and engineering to provide advanced polymers with comparably good performance. However, there are several inadequacies in terms of either technology or cost of production especially in the case of applications in environmental pollution. So, there is a need to have a fresh perspective on the design, properties and functions of these polymers with a view to developing strategies for future developments. The paper reviews the present state-of-art on biodegradable polymers and discusses the salient features of the design and properties of biodegradable polymers. Special emphasis is given to the problems and prospects of (1) approaches adopted to make non-biodegradable synthetic polymers such as polyethylene biodegradable and (2) biodegradable polymers and copolymers made from renewable resources especially poly(lactic acid) based polymers and copolymers which are emerging as the candidate biodegradable materials for the future.     

Processing and Physical Properties of Plastics Made from Soy Protein Polyester Blends

Blending soy protein with polyesters using a polyvinyllactam as a compatibilizer successfully made soy protein-based plastics. The polyesters used to produce blends included polycaprolactone (PCL) and Biomax (a commercial biodegradable polyester). The blends were processed by compounding extrusion and injection molding. Blends containing soy protein/Biomax-poly(vinyl alcohol) had tensile strengths ranging from 16–22 MPa, with samples containing larger percentages of the synthetic polymer exhibiting greater strengths. Blends made from soy protein, Biomax, and PCL had tensile strengths ranging from 27–33 MPa. All the blends had high Young's moduli but demonstrated brittle characteristics as evident from their low elongations at break, ranging from 1.8–3.1%. Plastics made from soy protein/polyester blends exhibited low water absorption and had good stability under ambient conditions relative to the plastics made from soy protein alone. Blends made from soy protein flour produced plastics with the lowest water absorption.     

Evaluation of the Biodegradability of Polyvinyl Alcohol/Starch Blends: A Methodological Comparison of Environmentally Friendly Materials

Polyvinyl alcohol (PVA) and starch are both biodegradable polymers. These two polymers can be prepared as biodegradable plastics that are emerging as one of the environmental friendly materials available now. In this study, after reacting with sodium trimetaphosphate (STMP), modified corn starch was blended with PVA in different ratios by a barbender. Test samples were prepared for mechanical and thermal properties measurements. The surface roughness and morphology of fractured surface of the samples were observed by an atomic force microscopy (AFM) and scanning electron microscope (SEM) measurements. Aqueous degradation by enzyme, water absorption and biodegradability behavior were evaluated for the degradability. The biodegradability of these materials was followed by bio-reactivity kinetics models. Results showed that the addition of modified starch could enhance its water uptake. With an addition of 20 wt% of modified starch, the blend had a maximum weight loss during enzymatic degradation. It was found that the degradability was enhanced with the addition of the starch. Analyzing the results of the biodegradability based on the kinetic models, the growth rate of the microorganism was found to be increasing with the increase of the content of starch in the PVA/starch blends in the first order reaction fashion. In our biodegradability analysis, i.e., based on the China national standards (CNS) 14432 regulations, we estimated the decomposition behavior based on the mentioned first order reaction. We found that the PVA/starch blends would take 32.47, 16.20 and 12.47 years to degrade by 70% as their starch content 0, 20 and 40 wt%, respectively.     

Effect of Hot Drawing on the Mechanical Properties of Biodegradable Fibers

The use of biodegradable polymers is increasingly attracting interest over the last years, since they can reduce the environmental effects related to disposal of traditional plastics and, in general, the use of fossil, non-renewable resources. One of the most promising applications is represented by fibers production. However, the orientation and the crystallinity degrees can significantly affect the mechanical properties. Therefore, it is of interest to investigate on the optimum processing conditions, in order to improve the mechanical properties. In particular, while crystallinity can be slightly modified by the processing, orientation can be significantly improved. In this work, the effects of hot stretching on the mechanical and structural properties of fibers made from two different families of biodegradable blends were investigated. The orientation proved to significantly change the mechanical properties, and it was shown that factors such as the different relaxation times, the different crystallization temperatures and the cooling rate can give opposite effects in the three investigated polymer systems with significant consequences on the mechanical behaviour of the fibers. In particular, the behaviour during fiber production in hot stretching, and the orientation mechanisms were studied and explained on the basis of rheological and thermal properties of the polymers.     

Electron Microscope Observation of Biodegradation of Polymers

Biodegradable polymers generally decompose in the various media in our environments. These environments contain soils, seawater, and activated sludge. If biodegradable materials waste is discarded, they decompose in these media. The biodegradation process of biodegradable polymers was investigated by scanning electron microscopy. Polycaprolactone, polybutylene succinate, and P(3HB-co-3HV) were tested. The shapes of holes on the decomposing surfaces are different according to the biodegradation media. Semispherical holes are observed on the surfaces of polybutylene succinate films degraded in activated sludge and cracks are observed on the surfaces of polycaprolactone films degraded in soil.     

Review of LCA studies of solid waste management systems – Part I: Lessons learned and perspectives

The continuously increasing solid waste generation worldwide calls for management strategies that integrate concerns for environmental sustainability. By quantifying environmental impacts of systems, life cycle assessment (LCA) is a tool, which can contribute to answer that call. But how, where and to which extent has it been applied to solid waste management systems (SWMSs) until now, and which lessons can be learnt from the findings of these LCA applications? To address these questions, we performed a critical review of 222 published LCA studies of SWMS. We first analysed the geographic distribution and found that the published studies have primarily been concentrated in Europe with little application in developing countries. In terms of technological coverage, they have largely overlooked application of LCA to waste prevention activities and to relevant waste types apart from household waste, e.g. construction and demolition waste. Waste management practitioners are thus encouraged to abridge these gaps in future applications of LCA. In addition to this contextual analysis, we also evaluated the findings of selected studies of good quality and found that there is little agreement in the conclusions among them. The strong dependence of each SWMS on local conditions, such as waste composition or energy system, prevents a meaningful generalisation of the LCA results as we find it in the waste hierarchy. We therefore recommend stakeholders in solid waste management to regard LCA as a tool, which, by its ability of capturing the local specific conditions in the modelling of environmental impacts and benefits of a SWMS, allows identifying critical problems and proposing improvement options adapted to the local specificities.     

Biodegradable Composite Foams of PLA and PHBV Using Subcritical CO<Subscript>2</Subscript>

One key strategy for increasing the application potential for biodegradable plastics lies in improving the physical and mechanical characteristics, which can be attained by inducing a cellular morphology in the pure polymer with the aid of a blowing agent, as well as by blending two or more polymers with the desirable properties. This paper examines the effect that blending two biodegradable polymers has on the thermal properties and morphology of the resultant foams blown with carbon dioxide (CO₂). Polylactic acid (PLA), polyhydroxybutyrate-co-valerate (PHBV) and blends of both were foamed and characterized in terms of thermal characteristics, relative density, cell size, and foam morphology. The results indicate that although PLA and PHBV are immiscible, the presence of small quantities of PHBV (25 wt%) could lead to low density foams with finer, more uniform cells. Furthermore, the crystallinity of PHBV was found to be unaffected by the presence of PLA in the composite, which supports the immiscibility of PLA and PHBV.     

Recent progress on preparation and properties of nanocomposites from recycled polymers: A review

Currently, the growing consumption of polymer products creates the large quantities of waste materials resulting in public concern in the environment and people life. Nanotechnology is assumed the important technology in the current century. Recently, many researchers have tried to develop this new science for polymer recycling. In this article, the application of different nanofillers in the recycled polymers such as PET, PP, HDPE, PVC, etc. and the attributed composites and blends is studied. The morphological, mechanical, rheological and thermal properties of prepared nanocomposites as well as the future challenges are extensively discussed. The present article determines the current status of nanotechnology in the polymer recycling which guide the future studies in this attractive field.     

Transdermal Delivery of Nicotine Using Pectin Isolated from Durian Fruit-Hulls-Based Polymer Blends as a Matrix Layer

Many natural polymers with various chemical structures are used to prepare transdermal patches. Pectin is a one interesting type of polymer because it can control drug release when used in transdermal patches. In Thailand, the waste from durian fruit-hulls is a major problem for the environment. However, the pectin from it can be isolated under acid conditions and used to prepare transdermal patches for nicotine delivery which has not yet been reported. As the isolated pectin is a natural polymer, the film made from isolated pectin is a brittle; therefore, adding a low protein natural rubber latex (LPNRL) polymer was needed to increase its flexibility. The transdermal patches were amorphous and had T_g values ranging from 81.0 to 93.3 °C. Moisture uptake, swelling ratio, and erosion values of the patches were significantly decreased after addition of LPNRL, which resulted in low hydrophilicity. The in vitro release and permeation of nicotine depends on the hydrophilicity of the patches. The kinetic models for in vitro release and permeation of nicotine were Higuchi model and zero order, respectively. In conclusion, pectin isolated from fruit-hulls of Mon Thong durians is an effective polymer to control the release of nicotine. It also is an option that could solve the environmental problems caused by durian fruit-hulls waste.     

Pet Waste Management by Chemical Recycling: A Review

The paper reviews the problem due to the use and disposal of synthetic polymers to the environment and its solutions; in particular poly (ethylene terphthalate). Wide spread application and non-biodegradability of the PET creates huge amounts of waste and disposal, tend to a serious problem. The most important cause for recycling and reprocessing the waste PET has arisen from the awareness and concern for environmental pollution. To manage this various methods of polymer recycling has been proposed. Among them chemical recycling, i.e. hydrolysis, methanolysis, glycolysis and aminolysis are reviewed in detail. Appropriate technology and waste disposal procedures based on the socio-economic aspect to solve this problem are suggested.     

Is There a Generic Environmental Advantage for Starch–PVOH Biopolymers Over Petrochemical Polymers?

The current study was undertaken to address the general question of whether there is an environmental advantage for renewable, starch?Cpolyvinyl alcohol (PVOH) biopolymer blends over petrochemical polymers. This was addressed using life cycle assessment (LCA) over a set of multiple case studies based on a consistent set of parameters and methodological background. A group of starch?CPVOH blended biopolymers derived from different feedstocks (wheat, potato, maize) were compared with high density polyethylene (HDPE), low density polyethylene (LDPE) and expanded polystyrene (EPS) in a range of applications. The results suggest that a general environmental advantage does not exist for the starch?CPVOH blended biopolymers over their petrochemical counterparts in all applications and, instead, a case-by-case approach is necessary to evaluate environmental pros and cons, based on specific comparisons. Overall, starch?CPVOH biopolymers were found to offer environmentally superior options to LDPE in thermal packaging applications. However, this was not the case in other applications, where the outcome of comparisons between starch?CPVOH biopolymers and HDPE/EPS varied according to various factors, including the specific end-of-life scenarios and the recycled content of the petrochemical polymers. A hierarchy of critical parameters for LCA-based decision-making concerning starch?CPVOH biopolymers is suggested as a general outcome of this research.