提高生物法分离制革污泥中铬分离效率的研究

在已确定污泥驯化最佳条件的基础上,通过改变滤材、液固分离条件,添加营养物质继续降低pH等方法,进行提高生物沥滤法分离制革污泥中铬的分离效率的研究。同时考察化学沥滤法（1∶1硫酸）在相同条件下的分离效率。试验结果表明：用相应pH值酸液（1∶1硫酸配制）淋洗,淋洗+闷洗和抽真空＋酸液淋洗等过滤方式可提高铬的分离效率。生物沥滤中当pH值下降至1.8时,分离效率即可达到94.65%,与直接用蒸馏水淋洗相比要高得多。化学沥滤中当pH值下降到1时,分离效果可达96.7%,沥滤污泥中剩余铬含量可达到制革污泥农用标准。     

生物沥滤-焚烧法处理制革污泥中铬迁移转化研究

采用生物沥滤-焚烧方法,先将制革污泥中大部分难溶的有毒重金属——铬从固相溶出转移至液相,之后将沥滤后制革污泥进行有效的固液两相分离,并对分离后的固相污泥进行焚烧处理实验,研究生物沥滤-焚烧处理法对制革污泥中的总Cr在不同介质中的浓度影响。结果表明,生物沥滤法处理制革污泥后,以金属离子交换形态存在的总Cr含量增加,其中68.56%的总Cr6+和87.70%的总Cr得以去除,去除效果十分明显;将沥滤脱水后的污泥进行焚烧处理,以残渣态形式存在的总Cr相对含量变大,迁移能力减弱;铬在高温下与其他重金属元素形成复杂的金属化合物及络合物:Cr1.3Fe0.7O0.5、Na4(CrO4)(SO4)、Ca5(CrO4)3O0.5,有助于今后进一步对整个生物沥滤-焚烧处理过程进行反应机理研究。     

制革污泥生物沥浸液中铬回收的方法与效果研究

对制革污泥生物沥浸液加碱沉淀回收Cr时碱的类型与用量、加碱后混合液的沉降速度、沉降比以及上层清液悬浮性固体(SS)及Cr含量与pH关系等进行了研究.结果表明,氧化镁和氧化钙均能很好地沉淀制革污泥经生物沥浸处理后所得的铬液,而液碱效果较差.综合沉淀效果和经济成本考虑,氧化钙作沉淀剂更为合适.将含Cr 720 mg/L的铬液调至pH 7.0,消耗氧化钙的质量浓度为10.0 g CaO/L铬液,能使Cr从液相完全去除,混合液的沉降比达40%.     

元素硫颗粒粒径对污泥重金属生物沥滤的影响

以城市污水处理厂剩余污泥作为处理介质,土著嗜酸氧化硫硫杆菌(Acidithiobacillus thiooxidans,A.thiooxi-dans)为主要沥滤微生物,采用序批式生物沥滤装置,就投加150~725μm的不同粒径元素硫对沥滤的酸化效果、硫酸根产率和重金属去除效果的影响进行了研究。结果表明,在元素硫投配量为3 g/L,曝气强度为1.0 L/(min.L)的条件下,元素硫粒径在165~215μm范围减小时能显著改善污泥酸化速度、提高酸化程度和硫酸根产率。底物元素硫的最佳粒径为165μm,此时沥滤体系pH下降速率为0.85个pH单位/d,硫酸根的产率为454.9 mg/(L.d),沥滤6 d后污泥中高浓度重金属Cu、Zn、Cd的去除率达到70.3%、81.2%、87.8%.     

底物对生物沥滤去除污泥中Cu、Zn的影响

分别以FeSO2·7H2O、单质S粉为底物,对污泥中的重金属进行生物沥滤试验.通过分析生物沥滤过程中pH、Fe2+、SO22-的变化及Cu、Zn的滤出率.探讨不同底物对重金属生物沥滤的影响.试验结果表明,以FeSO2·7H2O或单质S粉为底物.利用污泥中固有的硫杆菌可以降低污泥的pH.从而使重金属滤出.以单质S粉为底物的处理中,污泥pH最低下降到2.1;以FeSO2·7H2O为底物的处理中,pH最低下降到2.6.经14 d的生物沥滤,以单质S粉为底物时,底物为6 g/L的污泥样品Cu、Zn滤出率最高,分别为18.8%和34.8%;以FeSO2·7H2O为底物时,底物为25 g/L的污泥样品Cu、Zn滤出率最高,分别为29.1%和36.8%.优于以单质S粉为底物的滤出效果.     

一株嗜酸氧化亚铁硫杆菌的分离及沥滤效果研究

从山西某煤矿的酸性矿井水中分离得到菌株ATF-1,对其形态、生理生化特性、16SrDNA基因序列、生长特性及其对城市污泥的摇瓶沥滤效果进行了研究。结果表明:(1)该菌为革兰氏阴性菌,短杆状,经16SrDNA鉴定为嗜酸氧化亚铁硫杆菌(Acidthiobacillus ferrooxidans)。菌株ATF-1培养的最佳条件为初始pH 2.0、温度30℃、接种量10%(体积分数)、Fe2+投加量9.00g/L。(2)以菌株ATF-1作为沥滤菌处理城市污泥,经过15d的生物沥滤,污泥中Zn、Pb、Ni、Cu、Cd和Cr去除率的最大值分别为93.56%、46.54%、85.48%、97.68%、90.64%和45.15%,处理后污泥中的重金属含量符合《农用污泥中污染物控制标准》(GB4284—84)中规定的在酸性土壤上的最高容许含量。     

污泥酸化速率影响因子的探讨

采用城市污水厂污泥作为嗜酸微生物菌株来源,通过添加一定量的单质硫,使其中的嗜酸硫杆菌群大量增殖,并使污泥pH大幅降低.取得的培养物可用于废旧干电池中重金属沥滤等的处理.由于培养物对重金属沥滤效率和污泥的酸化速率密切相关,为此进行了不同的污泥种类、加硫量、污泥浓度和曝气强度对污泥酸化速率影响的实验.实验表明,初沉泥、二沉泥和混合浓缩污泥都能迅速利用硫产酸;加硫量(以100 mL污泥计)在0.5、1.0、2.0、4.0 g时,快速酸化的趋势相同.0.5 g的加硫量显示出略微慢的酸化速率,最后达到的最低pH在1.2左右,其他三个都降至1.0以下.污泥质量分数在0.5%、1.0%、2.0%、3.0%、4.0%时,也具有相同的酸化趋势,0.5%质量分数的污泥下降速率最快,这与较低浓度下污泥对pH的缓冲能力较小有关;曝气强度在0.45 L/min和0.3 L/min差别较小,5 d内能迅速降低pH,0.2 L/min的酸化速率较慢,足够长的时间(12 d)也能将pH降至2.5左右,0.1 L/min的曝气强度的酸化速率最慢,不能达到预期的酸化效果.     

不同污泥浓度对生物沥滤过程的影响

以硫酸亚铁盐作为底物,氧化亚铁硫杆菌（Thiobacillus ferrooxidans）为主要沥滤微生物,在底物投配比为10 g/L,温度为25℃,曝气量为1 L/min的条件下,对5种不同浓度的桂林城市污泥中重金属进行生物沥滤试验。结果表明,生物沥滤的污泥浓度宜控制在25.6 g/L,沥滤3 d后,污泥中超标元素Cu、Zn和Cd的去除率分别达到58.17%、75.90%和93.64%,沥滤处理后污泥中残余重金属含量符合污泥农用的国家标准。     

污泥生物沥滤工艺优化和重金属分配研究

为了得到嗜酸硫细菌沥滤污泥中重金属的最佳工艺参数,对沥滤过程进行3因素4水平的正交实验研究。3种影响因素的水平设置分别为:污泥浓度35、25、15和5 g/L,单质硫投加量15、10、5和1 g/L,接种量15、10、5和3 g/L。对沥滤过程污泥中7种重金属(As、Cd、Cr、Cu、Ni、Pb和Zn)的去除率进行极差分析,提出了因素影响程度依次为单质硫投加量污泥浓度接种量,且最佳工艺条件为:污泥浓度25 g/L,单质硫投加量10 g/L,接种量为5%。采用超声波-离心方法,分步提取污泥胞外聚合物(EPS)的2种形态:松散结合态(LB)和紧密结合态(TB)。分析其中的重金属浓度,提出沥滤后重金属在污泥EPS的赋存以LB为主。     

曝气强度对城市污泥重金属生物沥滤过程的影响研究

以氧化亚铁作为底物,氧化亚铁硫杆菌（Thiobacillusferrooxidans）为主要沥滤微生物,在底物投配比为10 g/L,温度为25℃,污泥浓度为123g/L的条件下,采用5种不同曝气强度对桂林城市污泥中重金属进行生物沥滤试验。结果表明,生物沥滤的经济曝气强度宜控制在每升污泥0.4L/（min·L）,沥滤3 d后,污泥中超标元素Cu、Zn和Cd的去除率分别达到62.53%、67.80%和54.63%,沥滤处理后污泥中残余重金属含量符合污泥农用的国家标准。     

Enhanced Cr bioleaching efficiency from tannery sludge with coinoculation of Acidithiobacillus thiooxidans TS6 and Brettanomyces B65 in an air-lift reactor

Bioleaching process has been demonstrated to be an effective technology in removing Cr from tannery sludge, but a large quantity of dissolved organic matter (DOM) present in tannery sludge often exhibits a marked toxicity to chemolithoautotrophic bioleaching bacteria such as Acidithiobacillus thiooxidans. The purpose of the present study was therefore to enhance Cr bioleaching efficiencies through introducing sludge DOM-degrading heterotrophic microorganism into the sulfur-based sludge bioleaching system. An acid-tolerant DOM-degrading yeast strain Brettanomyces B65 was successfully isolated from a local Haining tannery sludge and it could metabolize sludge DOM as a source of energy and carbon for growth. A combined bioleaching experiment (coupling Brettanomyces B65 and A. thiooxidans TS6) performed in an air-lift reactor indicated that the rates of sludge pH reduction and ORP increase were greatly improved, resulting in enhanced Cr solubilization. Compared with the 5 days required for maximum solubilization of Cr for the control (single bioleaching process without inoculation of Brettanomyces B65), the bioleaching period was significantly shorten to 3 days for the combined bioleaching system. Moreover, little nitrogen and phosphorous were lost and the content of Cr was below the permitted levels for land application after 3 days of bioleaching treatment.     

制革厂铬鞣废水中铬的回收处理研究

针对制革厂铬鞣废水含铬(Cr3 )量高、成分复杂、沉淀后铬泥纯度低的问题,本实验采用优化后的直接加碱沉淀法、絮凝后再加碱沉淀法和新型的硅铁电极法来回收铬鞣废水中的铬.3种方法所得铬泥的纯度分别在36%、65%和80%以上,比原铬泥纯度(27.7%)最多提高了近2倍.     

去除污泥中重金属铬的生物淋滤反应器设计与应用

用微生物方法去除污泥中重金属（生物淋滤法）是近年来发展的新技术，探索工程化的条件有重要的应用价值。设计了一套容积为1m^3的生物淋滤反应器，由生物淋滤池、搅拌器、曝气器和空气压缩机等构成。其中，搅拌叶轮由平叶桨和斜叶桨组合而成。利用制革污泥进行了半连续的生物淋滤试验，结果表明，在反应器中污泥与菌体和营养物质能充分混匀，经过2-5d的处理，污泥pH持续下降到2．0以下，污泥中铬的溶出率达90％-99．5％。     

去除污泥中重金属铬的生物淋滤反应器设计与应用

用微生物方法去除污泥中重金属(生物淋滤法)是近年来发展的新技术,探索工程化的条件有重要的应用价值。设计了一套容积为1 m3的生物淋滤反应器,由生物淋滤池、搅拌器、曝气器和空气压缩机等构成。其中,搅拌叶轮由平叶桨和斜叶桨组合而成。利用制革污泥进行了半连续的生物淋滤试验,结果表明,在反应器中污泥与菌体和营养物质能充分混匀,经过2~5 d的处理,污泥pH持续下降到2.0以下,污泥中铬的溶出率达90%~99.5%。     

Supercritical water oxidation of tannery sludge: Stabilization of chromium and destruction of organics

The supercritical water oxidation (SCWO) of industrial tannery sludge was investigated to understand the simultaneous destruction of organic pollutants and recovery of high content chromium. Experiments were performed in a batch reactor at temperatures of 350–500 °C, reaction time of 150–300 s and different oxygen ratios, to exhibit the effect of operation conditions. Results showed that removal efficiency of chemical oxygen demand (COD) increased with higher temperature, larger oxidant amount and reaction time; a maximum value of 96% was obtained. Meanwhile, destruction yield was much higher under supercritical conditions than that in subcritical water. In addition, removal efficiency of Cr from sludge reached more than 98% under all conditions; higher temperature played a positive role. Further, leaching toxicity tests of heavy metals in solid products were conducted based on toxicity characteristic leaching procedure. All heavy metals except nickel showed a greatly reduced leaching toxicity through their stabilization. The chromium oxide recovered in ash was amorphous below 550 °C, so that the structure of Cr could not be identified by X-ray diffraction pattern. Special attention should be paid on nickel as its leaching toxicity increased due to the corrosion of reactor surface under severe reaction conditions.     

微生物沥浸法去除底泥中的重金属

以硫酸亚铁盐为底物,培养以氧化亚铁硫杆菌为主要菌种的土著沥滤微生物,采用批式方法对湘江长沙段底泥进行微生物沥浸实验。实验结果表明,底物投加量与底泥固体浓度比(Sd/Sc)为1.5时已能满足底泥的微生物沥浸要求,进一步研究发现底泥固体浓度为13%、底物投加量为19.5 g/L、沥浸时间为6 d时,底泥中超标重金属Cd、Zn和Cu的去除率可分别达到83.1%、75.3%和61.2%;沥浸后底泥中大部分重金属以残渣态存在,且含量低于农用污泥中污染物控制标准,其中硫化物有机结合态Cu浸出较Zn、Cd需更低的pH,且Cu以间接机理浸出为主;以Fe2+为底物的沥浸体系中,黄铁矾的重吸附或共沉淀是沥浸实验后期重金属浸出率下降的原因之一。     

废旧镍镉电池的生物沥滤处理——沥滤停留时间的影响研究

用污泥加硫酸化液沥滤镍镉电池中的重金属是一种全新的工艺,该工艺主要由生物酸化反应器和金属沥滤反应器两个反应器组成.生物酸化反应器中产生的酸液就是沥滤电池中重金属的反应液.研究表明,酸化液在沥滤反应池的停留时间对沥滤的效果有显著影响.在1、4、7、12 d 4个停留时间中,4 d的效果是最好的,对金属Cd和Ni都用40 d左右基本实现了全部滤除;1d略微慢一些,Cd用了40 d,Ni用了45 d;7 d和12 d的沥滤时间都长于50 d.4 d产生的金属废液量是1 d的1/4,考虑到后续处理金属沥滤废液的工作量,选择4d的停留时间要优于1d.     

Case studies on biological treatment of tannery effluents in India

This paper presents a comparative assessment of the cost and quality of treatment of tannery wastewater in India by two common effluent treatment plants (CETPs) constructed for two tannery clusters, at Jajmau (Kanpur) and at Unnao in the state of Uttar Pradesh, India. The Jajmau plant is upflow anaerobic sludge blanket (UASB) process-based, while the Unnao plant is activated sludge process (ASP)-based. Investigations indicated that the ASP-based plant was superior in all respects. Total annualized costs, including capital and operation and maintenance costs, for the UASB and ASP plants were Rs. 4.24 million/million liters per day (MLD) and Rs. 3.36 million/MLD, respectively. Land requirements for the two CETPs were 1.4 hectares/MLD and 0.95 hectares/ MLD, respectively. Moreover, the treated UASB effluent had higher biochemical and chemical oxygen demand (BOD/ COD) and considerable amounts of other undesirable constituents, like chromium (Cr) and sulfide, as compared with the ASP effluent, which had lower BOD/COD and negligible concentration of sulfide and Cr. Sludge production from the UASB-based plant was also higher at 1.4 t/day/MLD, in comparison to the sludge production of 0.8 t/day/MLD for the ASP-based plant. Also, the entire sludge produced in the UASB-based plant was Cr-contaminated and, hence, hazardous, while only a small fraction of the sludge produced in the ASP-based plant was similarly contaminated. The results of this study are at variance with the conventional wisdom of the superiority of anaerobic processes for tannery wastewater treatment in tropical developing countries like India.