Investigation on mechanism of phosphate removal on carbonized sludge adsorbent

For the removal of phosphate (PO₄^3 -) from water, an adsorbent was prepared via carbonization of sewage sludge from a wastewater treatment plant: carbonized sludge adsorbent (CSA). The mechanism of phosphate removal was determined after studying the structure and chemical properties of the CSA and its influence on phosphate removal. The results demonstrate that phosphate adsorption by the CSA can be fitted with the pseudo second-order kinetics and Langmuir isotherm models, indicating that the adsorption is single molecular layer adsorption dominated by chemical reaction. The active sites binding phosphate on the surface are composed of mineral particles containing Si/Ca/Al/Fe. The mineral containing Ca, calcite, is the main factor responsible for phosphate removal. The phosphate removal mechanism is a complex process including crystallization via the interaction between Ca^2 + and PO₄^3 -; formation of precipitates of Ca^2 +, Al^3 +, and PO₄^3 -; and adsorption of PO₄^3 - on some recalcitrant oxides composed of Si/Al/Fe.     

Development and characterization of microwave composite cladding

The development of cladding through microwave radiation is recently explored and very few, initial studies were reported elsewhere. In order to explore more viability of process, (EWAC (Ni based) + 20% Cr₂₃C₆ powder) composite cladding has been developed on substrate austenitic stainless steel (SS-316). The experiments were conducted in domestic microwave oven and the clad of thickness, approximate 500 m has been developed by the exposure of microwave radiation at frequency 2.45 GHz for duration of 360 s. Typical clads cross sections of composite clads showed good metallurgical bonding with the substrate by partial dilution. The back scattered electron image of clad cross section showed the reinforced chromium carbide (Cr₂₃C₆) particles are uniformly distributed and well embedded in the Ni based matrix. The developed clad is free from visible solidification cracking and has significantly less porosity which is of the order of 0.90%. The XRD pattern of the developed clad showed the presence of FeNi₃, NiSi and Cr₂₃C₆ phases. The average Vicker's microhardness of developed clad was observed as 425 ± 140 Hv.     

Material flows in the life cycle of leather

This paper presents a study on the resource and environmental profile of leather for communicating to the consumers about the environmental burdens of leather products. The results indicate that significant environmental impacts were caused during the tanning and finishing of leather as well as the electricity production and transportation required in the life cycle. The use of fossil fuels in the production of energy has greater impact with increased emissions leading to about 15190 kg CO₂ equivalent of global warming and about 73 kg SO₂ equivalent of acidification while producing 100 m² of leather for shoe uppers. Further resource use of 174 kg of coal, 6.5 kg of fuel oil, 17.4 m³ of water and 348 kg of chemicals of which about 204 kg are hazardous are consumed, and wastewater of about 17 m³, BOD of 55 kg, COD of about 146 kg, TDS of 732 kg and solid waste of about 1445 kg are generated during the life cycle for the production of 100 m² of leather. The total solid waste generated is 1317 kg, out of which about 80% is biodegradable contributed by slaughtering, tanning and finishing stage, 14% is non-biodegradable contributed by tanning, finishing and electricity production stages and 6% is hazardous mainly from tanning and finishing stage of leather.     

Dairy farm CH4 and N2O emissions,from one square metre to the full farm scale

The greenhouse gas emissions from agricultural systems contribute significantly to the national budgets for most countries in Europe. Measurement techniques that can identify and quantify emissions are essential in order to improve the selection process of emission reduction options and to enable quantification of the effect of such options. Fast box emission measurements and mobile plume measurements were used to evaluate greenhouse gas emissions from farm sites. The box measurement technique was used to evaluate emissions from farmyard manure and several other potential source areas within the farm. Significant (up to 250 g CH₄ m⁻² day⁻¹and 0.4 g N₂O m⁻² day⁻¹) emissions from ditches close to stables on the farm site were found.Plume emission measurements from individual manure storages were performed at three sites. For a manure storage with 1200 m³ dairy slurry in Wageningen emission factors of 11 ± 5 g CH₄ m⁻³ manure day⁻¹ and 14 ± 8 mg N₂O m⁻³ manure day⁻¹ were obtained in February 2002.Mobile plume measurements were carried out during 4 days at distances between 30 and 300 m downwind of 20 different farms. Total farm emissions levels ranged from 14 to 95 kg CH₄ day⁻¹ for these sites. Expressed as emission per animal the levels were 0.7 ± 0.4 kg CH₄ animal⁻¹ day⁻¹ for conventional farms. For three farms that used straw bedding for the animals1.4 ± 0.2 kg CH₄ animal⁻¹ day⁻¹ was obtained. These factors include both respired methane and emission from manure in the stable and the outside storages.For a subset of these farms the CH₄ emission was compared with monthly averaged model emission calculations using FarmGHG. This model calculates imports, exports and flows of all products through the internal chains on the farm using daily time steps. The fit of modelled versus measured data has a slope of 0.97 but r² = 0.27. Measurements and model emission estimates agree well on average, for large farms within 30%. For small farms the differences can be up to a factor of 3. CH₄ emissions during winter seem to be underestimated.     

Bioconversion of industrial wastewater from palm oil processing to butanol by Clostridium saccharoperbutylacetonicum N1-4 (ATCC 13564)

The feasibility of utilizing enzymatic hydrolysates of separator sludge, a palm oil mill effluent, and sago starch in the acetone–butanol–ethanol fermentation by Clostridium saccharoperbutylacetonicum N1-4 (ATCC 13564) was investigated. The sludge hydrolysate was used as a growth medium substitute, a fermentation substrate, and as a source of nitrogen and micronutrients. Butanol produced, 3.50 g l⁻¹, was the same when the sludge hydrolysate was used as a second (refreshing) growth medium. As a substrate, initial nitrogen gas sparging shortened the lag phase which then enhanced butanol production. Fermentation without pH control enhanced butanol productivity whereas controlled fermentation at pH 5.5 and 5.8 progressively favored acid production while redox dyes, methyl and benzyl viologen, neutral red and methylene blue, had no effect on solvent production. As a source of nitrogen and micronutrients in sago starch hydrolysate, the final butanol concentration, 10.4 g l⁻¹, was comparable to that in glucose and sago starch hydrolysate media supplemented with tryptone–yeast–acetate (TYA) medium components medium, although productivity was low. Cell growth, butanol and total solvent productivity in TYA-supplemented sago starch hydrolysate and glucose media were the same.     

Second generation diesel fuel from renewable sources

The study is devoted to the issue of direct transformation of triacylglycerols (TAG) to diesel fuels applying a commercially available NiMo and NiW hydrorefining catalysts. It was proved that during hydrodesulphurisation also hydrodeoxygenation occurs and TAG can be converted to the fuel biocomponent by adding 6.5 % vol. of TAG to atmospheric gas oil. In this way, after hydroprocessing at mild conditions (temperature 320–360 °C, pressure 3.5–5.5 MPa, LHSV: 1.0 h^?1 and ratio H₂:HC = 500–1000 Nm³/m³, catalyst presence), gas oil containing 5–5.5% of biocomponent was prepared, characterized with standard performance and emission parameters. Performance and emission tests documented that even 5% vol. portion of bio-components reduces the controlled and uncontrolled emissions.     

Monitoring GHG from manure stores on organic and conventional dairy farms

Organic farming methods are claimed to be more environmentally friendly than conventional methods and the EU MIDAIR project had an overall aim to compare emissions from organic dairy farming with conventional methods of milk production. Manure stores are the second largest source of methane emissions (after enteric fermentation) on European dairy farming.The aim of this project was to measure green house gas (GHG) emissions from manures in covered and uncovered slurry stores and farm yard manure (FYM) heaps. The chosen method for measuring these emissions was the tracer ratio method, using sulphur hexafluoride (SF₆) as the tracer gas, the limitations of this method prevented successful measurements being made on some of the stores and a modified method was used on the covered stores. The difference in concentration of the upwind and downwind samples and interfering sources were limiting factors. FYM emission measurements were successful only when the manure was stored indoors.Methane emissions were successfully measured over a 12 month period from the uncovered slurry stores. Emission rates from the uncovered slurry stores on the conventional farm and the organic farm ranged from 14.4 to 49.6 and from 12.4 to 42.3 g C m⁻³ d⁻¹, respectively, with the mean CH₄ emission rates of 35 and 26 g C m⁻³ d⁻¹. On both farms, nitrous oxide emissions were close to zero.Methane emissions measured from the indoor organic FYM in summer were 17.1 g C m⁻³ d⁻¹ and the nitrous oxide emission was 411 mg N m⁻³ d⁻¹.The covered slurry stores were in such close proximity to other GHG sources that the tracer ratio method was unsuitable and the air-injection method was adopted. The measured emissions from covered slurry stores of CH₄, CO₂ and NH₃ were, respectively, 14.9 g C m⁻³ d⁻¹, 12.9 g C m⁻³ d⁻¹ and 18.6 mg NH₃ m⁻² d⁻¹ of slurry in February and 12.0 g C m⁻³ d⁻¹, 9.5 g C m⁻³ d⁻¹ and 335 mg NH₃ m⁻² d⁻¹ slurry in March. No nitrous oxide production could be measured.     

Methane,nitrous oxide and ammonia emissions during storage and after application of dairy cattle slurry and influence of slurry treatment

Slurries are a significant source of CH₄, NH₃ and N₂O emissions to the atmosphere. The research project aimed at quantifying CH₄, NH₃ and N₂O emissions from liquid manure stores and after manure application under field conditions. The influence of the manure treatment options “no treatment”, “slurry separation”, “anaerobic digestion”, “slurry aeration” and “straw cover” on the emission level was investigated. Approximately 10 m³ of differently treated slurry were stored in pilot scale slurry tanks. Emissions were followed for c. 80 days. After the storage period, slurries were applied to permanent grassland. Greenhouse gas emissions from slurry were mainly caused by methane emissions during storage and by nitrous oxide emissions after field application of manures. Mitigation of GHG emissions can be achieved by a reduction in slurry dry matter and easily degradable organic matter content. Ammonia emissions mainly occurred after field application. Untreated slurry emitted 226.8 g NH₃ m⁻³ and 92.4 kg CO₂ eq. m⁻³ (storage and field application). Slurry separation (liquid fraction and composting of the solid fraction) resulted in NH₃ losses of 402.9 g m⁻³ and GHG losses of 58.5 kg CO₂ eq. m⁻³. Anaerobic digestion was a very effective means to reduce GHG emissions. 37.9 kg CO₂ eq. m⁻³ were lost. NH₃ emissions were similar to those from untreated slurry. Covering the slurry store with a layer of chopped straw instead of a wooden cover increased NH₃ emissions to 320.4 g m⁻³ and GHG emissions to 119.7 kg CO₂ eq. m⁻³. Slurry aeration nearly doubled NH₃ emissions compared to untreated slurry. GHG emissions were reduced to 53.3 kg CO₂ eq. m⁻³.     

Soil-profile organic carbon and total nitrogen during 12 years of pasture management in the Southern Piedmont USA

Soil organic C (SOC) and total soil N (TSN) sequestration estimates are needed to improve our understanding of management influences on soil fertility and terrestrial C cycling related to greenhouse gas emission. We evaluated the factorial combination of nutrient source (inorganic, mixed inorganic and organic, and organic as broiler litter) and forage utilization (unharvested, low and high cattle grazing pressure, and hayed monthly) on soil-profile distribution (0–150 cm) of SOC and TSN during 12 years of pasture management on a Typic Kanhapludult (Acrisol) in Georgia, USA. Nutrient source rarely affected SOC and TSN in the soil profile, despite addition of 73.6 Mg ha^?1 (dry weight) of broiler litter during 12 years of treatment. At the end of 12 years, contents of SOC and TSN at a depth of 0–90 cm under haying were only 82 ± 5% (mean ± S.D. among treatments) of those under grazed management. Within grazed pastures, contents of SOC and TSN at a depth of 0–90 cm were greatest within 5 m of shade and water sources and only 83 ± 7% of maximum at a distance of 30 m and 92 ± 14% of maximum at a distance of 80 m, suggesting a zone of enrichment within pastures due to animal behavior. During 12 years, the annual rate of change in SOC (0–90 cm) followed the order: low grazing pressure (1.17 Mg C ha^?1 year^?1) > unharvested (0.64 Mg C ha^?1 year^?1) = high grazing pressure (0.51 Mg C ha^?1 year^?1) > hayed (?0.22 Mg C ha^?1 year^?1). This study demonstrated that surface accumulation of SOC and TSN occurred, but that increased variability and loss of SOC with depth reduced the significance of surface effects.     

The role of indicator choice in quantifying the threat of atmospheric ammonia to the ‘Natura 2000’ network

New ‘critical levels’ (CLE) for assessing the effects of atmospheric ammonia on sensitive ecosystems have recently been adopted by the United Nations Economic Commission for Europe (UNECE) of 1 and 3 [2–4] μg NH₃ m^?3 of ambient air (including water vapour), for different species sensitivities and their associated habitats. Based on these values, we examined how indicator choice affects estimates of stock-at-risk in the European ‘Natura 2000’ network.We applied an atmospheric model, FRAME, to estimate surface air concentrations of ammonia at 5 km and 1 km resolution for the UK network of Natura sites, optionally including calibration with the National Ammonia Monitoring Network. As a base indicator, we estimated the overall percentage area of the UK Natura network that exceeded critical level thresholds (‘Area Weighted Indicator’, AWI). We compared this with an alternative approach, estimating the percentage number of Natura sites where the critical level was exceeded (‘Designation Weighted Indicator’, DWI), which we consider more relevant under the terms of the Habitats Directive.Using the AWI (with 1 km calibrated ammonia), we estimate that 11.2%, 1.3% and 0.2% area of the UK Natura network exceeds the critical level values of 1, 2 and 3 μg NH₃ m^?3, respectively. By contrast, using the DWI, the equivalent exceedances are 59.1%, 23.6% and 9.8%. The highest regional exceedance (DWI, critical level 1 μg NH₃ m^?3) was calculated for England (91.9% exceeded), and the lowest for Scotland (24.0% exceeded). High resolution maps show that the larger threat estimated by the DWI approach is explained by (i) an anti-correlation between NH₃ concentration and Natura site area and (ii) the fact that exceedance over part of a Natura site is considered to represent a threat to the integrity of the whole site.     

Emissions of N2O and NH3, and nitrogen leaching from direct seeded rice under different tillage practices in central China

Tillage practices affect the fate of fertilizer nitrogen (N) through influencing transformations of N, but few studies have examined N₂O and NH₃ emissions, and N leaching from different rice tillage systems. Thus the objective of this study was to assess N₂O emission, NH₃ volatilization and N leaching from direct seeded rice in conventional tillage (CT) and no-tillage (NT) production systems in the subtropical region of China during the 2008 and 2009 rice growing seasons. Treatments were established following a split-plot design of a randomized complete block with tillage practices as the main plot and N fertilizer level as the sub-plot treatment, and there were four treatments: NT + no fertilizer (NT0), CT + no fertilizer (CT0), NT + compound fertilizer (NTC) and CT + compound fertilizer (CTC), respectively. Results showed that N fertilization significantly increased (p < 0.01) N₂O emissions, NH₃ volatilization and N leaching from rice fields in both years. In general, there was no significant difference in N₂O emissions and NH₃ volatilization between NT0 and CT0 in both years, while NTC had significantly higher (p < 0.05) N₂O emissions and NH₃ volatilization compared to CTC. Over the two rice growing seasons, NTC showed 32% and 47% higher N₂O emissions, and 29% and 52% higher NH₃ losses than CTC. Higher (p < 0.05) N₂O emissions from NTC than CTC were presumably due to higher soil organic C and greater denitrification. Total N and NO₃^? concentrations were higher (p < 0.05) in CTC than NTC, but larger volumes of percolation water in NTC than CTC resulted in no significant difference in leakage of total N and NO₃^?. Hence, application of N fertilizer in combination with NT appeared to be ineffective in reducing N losses from N fertilizer in paddy fields.     

The effect of pitting corrosion on split sleeve cold hole expanded,bare 7075-T651 aluminium alloy

As part of an aircraft fleet fatigue life improvement program, investigation has been carried out into the effect pitting corrosion has on bare 7075-T651 which had undergone split sleeve cold hole expansion. Constant amplitude sinusoidal loading was applied to fatigue test coupons which had pitting corrosion induced upon them by a modified cyclic immersion process using a 3.5% NaCl solution. A pit depth of 39–58 μm was found to significantly reduce the increased fatigue life gains achieved by carrying out cold hole expansion. At 137.9 MPa fatigue life was reduced from achieving run out of ten million cycles to an average 371 × 10³ cycles, while at 165.5 MPa average fatigue life was reduced from 810 × 10³ to 65 × 10³ cycles. The fracture surfaces were analysed under a scanning electron microscope where each displayed an individual crack initiation site located on the material surface within the zone of residual circumferential stress.     

Ammonia and nitrous oxide emissions following land application of high and low nitrogen pig manures to winter wheat at three growth stages

Nitrous oxide (N₂O) and ammonia (NH₃) emissions from surface applied high (HN) and low (LN) nitrogen pig manures were measured under field conditions. Manures were band-spread to a winter wheat crop at three growth stages—mid-tillering, stem elongation and flag leaf emergence. The N₂O flux rates were measured using the static chamber technique while NH₃ volatilisation was assessed using a micrometeorological mass balance technique with passive flux samplers. The N₂O emissions were episodic in nature with flux rates observed ranging from 2.8 to 31.5 g N₂O–N ha^?1 day^?1 (P < 0.001). Higher N₂O emissions generally occurred after rainfall events. Highest N₂O losses were observed from the HN treatment with LN manure use decreasing emissions by 18% (P < 0.03). The NH₃ volatilisation rates were highest within 1 h of manure application with 95% of emissions occurring within 24 h (P < 0.001). Cumulative N loss was highest at mid-tillering as low crop canopy cover and increased wind-speeds enhanced NH₃ loss (P < 0.001). Highest emissions were measured from the HN manure (P < 0.03). Total ammoniacal N loss ranged from 6 to 11%. Crop N uptake and grain yield were unaffected by application timing or manure type. Therefore, the use of LN manures decreased gaseous emissions of N₂O and NH₃ without any adverse effects on crop performance.     

Biogas production from maize and dairy cattle manure—Influence of biomass composition on the methane yield

There is an increasing world wide demand for energy crops and animal manures for biogas production. To meet these demands, this research project aimed at optimising anaerobic digestion of maize and dairy cattle manures. Methane production was measured for 60 days in 1 l eudiometer batch digesters at 38 °C. Manure received from dairy cows with medium milk yield that were fed a well balanced diet produced the highest specific methane yield of 166.3 Nl CH₄ kg VS⁻¹. Thirteen early to late ripening maize varieties were grown on several locations in Austria. Late ripening varieties produced more biomass than medium or early ripening varieties. On fertile locations in Austria more than 30 Mg VS ha⁻¹ can be produced. The methane yield declined as the crop approaches full ripeness. With late ripening maize varieties, yields ranged between 312 and 365 Nl CH₄ kg VS⁻¹ (milk ripeness) and 268–286 Nl CH₄ kg VS⁻¹ (full ripeness). Silaging increased the methane yield by about 25% compared to green, non-conserved maize. Maize (Zea mays L.) is optimally harvested, when the product from specific methane yield and VS yield per hectare reaches a maximum. With early to medium ripening varieties (FAO 240–390), the optimum harvesting time is at the “end of wax ripeness”. Late ripening varieties (FAO ca. 600) may be harvested later, towards “full ripeness”. Maximum methane yield per hectare from late ripening maize varieties ranged between 7100 and 9000 Nm³ CH₄ ha⁻¹. Early and medium ripening varieties yielded 5300–8500 Nm³ CH₄ ha⁻¹ when grown in favourable regions. The highest methane yield per hectare was achieved from digestion of whole maize crops. Digestion of corns only or of corn cob mix resulted in a reduction in methane yield per hectare of 70 and 43%, respectively. From the digestion experiments a multiple linear regression equation, the Methane Energy Value Model, was derived that estimates methane production from the composition of maize. It is a helpful tool to optimise biogas production from energy crops. The Methane Energy Value Model requires further validation and refinement.     

Micro-flood (MF) technology for sustainable manufacturing operations that are coolant less and occupationally friendly

This paper presents a new technology for minimizing the use of metalworking fluids (MWFs) during the machining process that is atomization-less and occupational friendly. Micro-flood (MF) technology utilizes direct contact between the cutting tool and the MWF without the interaction of a gas medium. Experiments were conducted in high volume mass production environment turning HSLA (high strength low alloy) SAE 070Y steel. Machining performance and total air mass particulates were investigated in dry machining, Near dry machining (NDM) via atomized spray mist and MF technology. Open-atmosphere air monitoring indicated that total mass particulates behaved in an almost linear fashion with respect to gas atomization pressure, whereas the MWF flow rate demonstrated logarithmic trends in NDM applications using an atomized spray. Nozzle orientations directed upward into the air also produced higher mg/m³ concentrations (such as flank) than chip and rake face orientations that were directed down. Greater separation existed at higher gas atomization pressures, MWF flow rates and by changing the MWF type. At extreme limits, nozzle orientation affected mg/m³ concentration as much as 4–5 mg/m³ for water-miscible MWFs and 15–22 mg/m³ for non-water-miscible MWFs. Tool-life performance varied greatly among MWF type and flow rate, and in all cases MF technology performed better than NDM using an atomized spray mist. Direct and consistent MWF penetration to cutting zone using MF technology lowered tool-wear on the average of 12–75% compared to NDM at the same MWF flow rate. Compared to dry machining, NDM improved tool-wear on the average by 20–243%. In one case, tool-wear performance was improved by 616% at 0.15 mm using MF technology compared to dry machining at a nominal 0.925 mm tool-wear. Overall, a large mass reduction of particulates can be achieved employing MF technology that would have been unrealistic for an open-atmosphere machining environment employing an atomized spray mist. On the average, MF technology can maintain a total air mass particulate of less than 0.4 mg/m³ in the occupational work zone using MWF flow rates up to 1260 ml/h, regardless of the MWF classification. Atomized spray mist applications are capable meeting the 5 mg/m³ OSHA limit if MWF flow rates are less than 160 ml/h, air pressures are less than 0.137 MPa (20 psi) using water-miscible MWFs and air pressures are less than 0.0344 MPa (5 psi) using non-water-miscible MWFs.     

Life-cycle environmental and economic impacts of energy-crop fuel-chains: an integrated assessment of potential GHG avoidance in Ireland

This paper combines life-cycle analyses and economic analyses for Miscanthus and willow heat and electricity fuel-chains in Ireland. Displaced agricultural land-uses and conventional fuels were considered in fuel-chain permutations. Avoided greenhouse gas (GHG) emissions ranged from 7.7 to 35.2 t CO₂ eq. ha⁻¹ a⁻¹. Most fuel-chain permutations exhibited positive discounted financial returns, despite losses for particular entities at a farm-gate processed-biomass price of €100 t⁻¹ dry-matter. Attributing a value of €10 t⁻¹ CO₂ eq. to avoided GHG emissions, but subtracting financial returns associated with displaced fuel supplies, resulted in discounted annual national economic benefits (DANEBs) ranging from −457 to 1887€ ha⁻¹ a⁻¹. Extrapolating a plausible combination of fuel-chains up to a national indicative scenario resulted in GHG emission avoidance of 3.56 Mt CO₂ eq. a⁻¹ (5.2% of national emissions), a DANEB of 167 M€, and required 4.6% of national agricultural land area. As cost-effective national GHG avoidance options, Miscanthus and willow fuel-chains are robust to variation in yields and CO₂ price, and appear to represent an efficient land-use option (e.g. compared with liquid biofuel production). Policies promoting utilisation of these energy-crops could avoid unnecessary, and environmentally questionable, future purchase of carbon credits, as currently required for national Kyoto compliance.     

Nitrous oxide emissions from a dung heap measured by chambers and plume methods

Dung heaps provide a large, spatial and temporal variable, source of the greenhouse gas N₂O. In this paper emission rates measured by static and flow through chamber methods, which enclose only a small area of the heap, were compared with Gaussian plume and tracer ratio methods, which measure the emissions from the entire dung heap. The dung heap was a 300 m³ heap, composed of material from nearby cattle sheds. From the flow through and static chambers it was estimated that the dung heap emitted 315 and 51 g N₂ON m⁻³ day⁻¹, respectively. The spatial variability between the chambers and chamber methods was large. Standard deviations of the mean fluxes were >75% of the average flux. The smaller emissions were measured on the slopes of the heap and the larger emissions on the ridge. The plume of N₂O was measured downwind of the dung heap by (1) tunable diode laser spectroscopy and calculation of the N₂O source strength of the heap using Gaussian plume theory and (2) tracer ratio method releasing SF₆ from the heap summit and capture in Tedlar bags downwind with subsequent analysis by gas chromatography. The Gaussian plume theory calculated an average N₂O source strength of 5.3 g N₂ON m⁻³ day⁻¹ (1.4–6.7 g N₂ON m⁻³ day⁻¹). The tracer ratio method calculated a slightly larger average emission rate of 14.4 g N₂ON m⁻³ day⁻¹ (7.4–38.6 g N₂ON m⁻³ day⁻¹). Both methods were successfully validated by point release of SF₆ and N₂O, which suggests that the micrometeorological methods provided a good estimate of the source strength of the heap, whereas the few chamber measurements overestimated its source strength.     

Exceedance of modern ‘background’ fine-grained sediment delivery to rivers due to current agricultural land use and uptake of water pollution mitigation options across England and Wales

Excessive loss of fine-grained sediment to rivers is widely recognised as a global environmental problem. To address this issue, policy teams and catchment managers require an estimate of the ‘gap’ requiring remediation, as represented by the excess above ‘background’ losses. Accordingly, recent work has estimated the exceedance of modern ‘background’ sediment delivery to rivers at national scale across England and Wales due to (i) current agricultural land cover, cropping and stocking, and (ii) current land use corrected for the uptake of on-farm mitigation measures. This sectoral focus recognises that, nationally, agriculture has been identified as the principal source of fine sediment loss to the aquatic environment. Two estimates of modern ‘background’ sediment loss, based on paleolimnological evidence, were used in the analysis; the target modern ‘background’ (TMBSDR) and maximum modern ‘background’ (MMBSDR) sediment delivery to rivers. For individual (n = 4485) non-coastal water bodies, the sediment ‘gap’ in excess of TMBSDR and MMBSDR, due to current land cover, cropping and stocking, was estimated to range up to 1368 kg ha⁻¹ yr⁻¹ (median 61 kg ha⁻¹ yr⁻¹) and 1321 kg ha⁻¹ yr⁻¹ (median 19 kg ha⁻¹ yr⁻¹), respectively. The respective ranges in conjunction with current land cover, cropping and stocking but corrected for the potential impact of on-farm sediment mitigation measures were up to 1315 kg ha⁻¹ yr⁻¹ (median 50 kg ha⁻¹ yr⁻¹) and 1269 kg ha⁻¹ yr⁻¹ (median 8 kg ha⁻¹ yr⁻¹). Multiplication of the estimates of excess sediment loss corrected for current measure uptake, above TMBSDR and MMBSDR, with estimated maximum unit damage costs for the detrimental impacts of sediment pollution on ecosystem goods and services, suggested respective water body ranges up to 495 £ ha⁻¹ yr⁻¹ and 478 £ ha⁻¹ yr⁻¹. Nationally, the total loss of sediment in excess of TMBSDR was estimated at 1,389,818 t yr⁻¹ equating to maximum environmental damage costs of £523 M yr⁻¹, due to current structural land use, compared to 1,225,440 t yr⁻¹ equating to maximum damage costs of £462 M yr⁻¹ due the uptake of on-farm sediment control measures. The corresponding total loss of sediment in excess of MMBSDR was estimated at 1,038,764 t yr⁻¹ equating to maximum damage costs of £462 M yr⁻¹, compared with 890,146 t yr⁻¹ and £335 M yr⁻¹ correcting excess agricultural sediment loss for current implementation of abatement measures supported by policy instruments. This work suggests that the current uptake of sediment control measures on farms across England and Wales is delivering limited benefits in terms of reducing loadings to rivers and associated environmental damage costs.     

Linking spatio-temporal variation of crop response with sediment deposition along paddy rice terraces

In tropical mountainous regions of South East Asia, intensive cultivation of annual crops on steep slopes makes the area prone to erosion resulting in decreasing soil fertility. Sediment deposition in the valleys, however, can enhance soil fertility, depending on the quality of the sediments, and influence crop productivity. The aim of the study was to assess (i) the spatio-temporal variation in grain yield along two rice terrace cascades in the uplands of northern Viet Nam, (ii) possible linkage of sediment deposition with the observed variation in grain yield, and (iii) whether spatial variation in soil water or nitrogen availability influenced the obtained yields masking the effect of inherent soil fertility using carbon isotope (¹³C) discrimination and ¹⁵N natural abundance techniques. In order to evaluate the impact of seasonal conditions, fertilizer use and sediment quality on rice performance, ¹⁵N and ¹³C stable isotope compositions of rice leaves and grains taken after harvest were examined and combined with soil fertility information and rice performance using multivariate statistics. The observed grain yields for the non-fertilized fields, averaged over both cascades, accounted for 4.0 ± 1.4 Mg ha^?1 and 6.6 ± 2.5 Mg ha^?1 in the spring and summer crop, respectively, while for the fertilized fields, grain yields of 6.5 ± 2.1 Mg ha^?1 and 6.9 ± 2.1 Mg ha^?1 were obtained. In general, the spatial variation of rice grain yield was strongly and significantly linked to sediment induced soil fertility and textural changes, such as soil organic carbon (r 0.34/0.77 for Cascades 1 and 2, respectively) and sand fraction (r ?0.88/?0.34). However, the observed seasonal alteration in topsoil quality, due to sediment deposition over two cropping cycles, was not sufficient to fully account for spatial variability in rice productivity. Spatial variability in soil water availability, assessed through ¹³C discrimination, was mainly present in the spring crop and was linearly related to the distance from the irrigation channel, and overshadowed in Cascade 2 the expected yield trends based on sediment deposition. Although δ¹⁵N signatures in plants indicated sufficient N uptake, grain yields were not found to be always significantly influenced by fertilizer application. These results showed the importance of integrating sediment enrichment in paddy fields within soil fertility analysis. Furthermore, where the effect of inherent soil fertility on rice productivity is masked by soil water or nitrogen availability, the use of ¹³C and ¹⁵N stable isotopes and its integration with conventional techniques showed potential to enhance the understanding of the influence of erosion – sedimentation and nutrient fluxes on crop productivity, at toposequence level.     

Lodging in rice can be alleviated by atmospheric CO2 enrichment

The projected increase of atmospheric CO₂ concentration [CO₂] is expected to increase yield of agricultural C₃ crops, but little is known about effects of [CO₂] on lodging that can reduce yield. This study examined the interaction between [CO₂] and nitrogen (N) fertilization on the lodging of rice (Oryza sativa L.) using free-air CO₂ enrichment (FACE) systems installed in paddy fields at Shizukuishi, Iwate, Japan (39°38′N, 140°57′E). Rice plants were grown under two levels of [CO₂] (ambient = 365 μmol mol⁻¹; elevated [CO₂] = 548 μmol mol⁻¹) and three N fertilization regimes: a single initial basal application of controlled-release urea (8 g N m⁻², CRN), split fertilization with a standard amount of ammonium sulfate (9 g N m⁻², MN), and ample N (15 g N m⁻², HN). Lodging score (six ranks at 18° intervals, with larger scores indicating greater bending), yield, and yield components were measured at maturity. The lodging score was significantly higher under HN than under CRN and MN, but lodging was alleviated by elevated [CO₂] under HN. This alleviation was associated with the shortened and thickened lower internodes, but was not associated with a change in the plant's mass moment around the culm base. A positively significant correlation between lodging score and ripening percentage indicated that ripening percentage decreased by 4.5% per one-unit increase in lodging score. These findings will be useful to develop functional algorithm that can be incorporated into mechanistic crop models to predict rice production more accurately in a changing climate and with different cultural practices.