Polycyclic aromatic hydrocarbon emissions from clinical waste incineration

Since the introduction of the Environmental Protection Act in the UK, there are few reports of PAH emissions from clinical waste incinerators (CWIs) operating to improved performance standards. The main aim of this study is to determine PAH emissions from a state-of-the-art CWI focusing on the effects of reactive gases and operating variables on emissions. This was carried out by collection of stack samples over three phases of operation.

At stack conditions, most PAHs are predicted to be in the vapour phase. Reactive losses of PAHs were closely correlated by rank with expected reactivities from laboratory studies. Estimates of emissions incorporating sampling losses were derived, although no correlation was found between PAH losses and the modest levels of reactive stack gases. PAH concentrations were one to two orders of magnitude lower than earlier reports from incinerators without effective air pollution control equipment (APCE). The low levels of carbon monoxide recorded were not correlated with any PAHs.

This study demonstrates the impact of efficient combustion conditions and APCE on PAH emissions from a CWI.     

水葫芦多环芳烃含量及其与脂肪含量的关系

利用气相色谱/质谱联用仪测定了湿地浮水植物水葫芦体内16种优先控制多环芳烃(PAHs)的含量,分析了PAHs的组成,并研究了体内脂肪含量对PAHs含量的影响。结果表明,不同进水方式(间歇和连续进水)时,水葫芦体内PAHs的含量差别不大,16种PAHs的含量分别为1186.67 ng/g(dw)(间歇进水)和1280.00 ng/g(dw)(连续进水),且以2环、3环和4环为主。水葫芦体内,2环、3环、4环和5环PAHs在间歇进水百分比含量分别为27.55%、34.27%、23.31%和14.47%,连续进水百分比含量分别为29.43%、33.85%、23.81%和13.54%,6环PAHs在水葫芦体内没有检测到。水葫芦积累PAHs的量占湿地系统去除PAHs总量的1.16%~1.99%,其体内脂肪含量与其对PAHs的积累作用有一定的相关性,脂肪含量越高,PAHs的含量也越大。     

Metal ion removal from water by sorption on paper mill sludge

Chromatographic columns packed with paper mill sludge are employed for metal ion recovery from water. The breakthrough curves show that cadmium, copper, lead and silver are removed from acid solutions (pH 2, 4); the affinity series is Pb(II)>Cu(II)>Ag(I)>Cd(II). Both the amount of metal retained and the metal-matrix interaction are pH dependent; the sorptive capacity increases with increasing pH. When the metals are present together at the same initial concentrations a competition among the different ions occurs although the affinity order remains unchanged. In metal recovery from the paper mill sludge column, the total amount of the cadmium and copper is displaced by HCl 1.0 M, 65% of the lead by HCl 0.1 M and 75% of the silver by HNO(3) 0.1 M. More than 95% of copper and lead and less than 20% of cadmium were recovered with HCl 0.1 M when the metals were present at the same time.     

Polycyclic aromatic hydrocarbon emission from straw burning and the influence of combustion parameters

A simulated burning experiment was conducted in a tubular furnace system to examine the emission of polycyclic aromatic hydrocarbons (PAHs) from the burning of rice and bean straw, and the influence of combustion parameters was investigated. Total emission amounts of 16 PAHs (∑PAHs) from the burning of rice and bean straw ranged from 9.29 to 23.6 μg g^?1 and from 3.13 to 49.9 μg g^?1, respectively, which increased with the increase of temperatures from 200 to 700 °C. The contribution of combustion to individual PAH yields was about 80.6–100%, which was generally increased with the increase of burning temperature. Moisture content in straw had a negative effect on PAH formation, especially on PAHs with low molecular weight. ∑PAHs emission amounts decreased by 78.2% for bean straw with a moisture content of 30% in comparison with that for dried straw. In addition, PAH emission amounts increased with the increase of O₂ content in supplied air and then decreased, which showed a maximum emission at O₂ content of 40%. The source fingerprint of PAHs in emission from straw burning was established, which showed that naphthalene accounted for 35.0 ± 7.4% of ∑PAHs. Based on the experimental data, emission amounts of ∑PAHs from the burning of rice and bean straw were estimated to be 320–357 and 32.5–76.0 tons to ambient air per year in China, respectively.     

Polycyclic aromatic hydrocarbon exhaust emissions from different reformulated diesel fuels and engine operating conditions

The study of light-duty diesel engine exhaust emissions is important due to their impact on atmospheric chemistry and air pollution. In this study, both the gas and the particulate phase of fuel exhaust were analyzed to investigate the effects of diesel reformulation and engine operating parameters. The research was focused on polycyclic aromatic hydrocarbon (PAH) compounds on particulate phase due to their high toxicity. These were analyzed using a gas chromatography–mass spectrometry (GC–MS) methodology.Although PAH profiles changed for diesel fuels with low-sulfur content and different percentages of aromatic hydrocarbons (5–25%), no significant differences for total PAH concentrations were detected. However, rape oil methyl ester biodiesel showed a greater number of PAH compounds, but in lower concentrations (close to 50%) than the reformulated diesel fuels. In addition, four engine operating conditions were evaluated, and the results showed that, during cold start, higher concentrations were observed for high molecular weight PAHs than during idling cycle and that the acceleration cycles provided higher concentrations than the steady-state conditions. Correlations between particulate PAHs and gas phase products were also observed.The emission of PAH compounds from the incomplete combustion of diesel fuel depended greatly on the source of the fuel and the driving patterns.     

Remediation of a chlorinated aromatic hydrocarbon in water by photoelectrocatalysis

Photoelectrocatalysis driven by visible light offers a new and potentially powerful technology for the remediation of water contaminated by organo-xenobiotics. In this study, the performance of a visible light-driven photoelectrocatalytic (PEC) batch reactor, applying a tungsten trioxide (WO₃) photoelectrode, to degrade the model pollutant 2,4-dichlorophenol (2,4-DCP) was monitored both by toxicological assessment (biosensing) and chemical analysis. The bacterial biosensor used to assess the presence of toxicity of the parent molecule and its breakdown products was a multicopy plasmid lux-marked E. coli HB101 pUCD607. The bacterial biosensor traced the removal of 2,4-DCP, and in some case, its toxicity response suggests the identification of transient toxic intermediates. The loss of the parent molecule, 2,4-DCP determined by HPLC, corresponded to the recorded photocurrents. Photoelectrocatalysis offers considerable potential for the remediation of chlorinated hydrocarbons, and that the biosensor based toxicity results identified likely compatibility of this technology with conventional, biological wastewater treatment.     

Polycyclic aromatic hydrocarbon contamination in an urban area assessed by Quercus ilex leaves and soil

We investigated the PAH contamination of Naples urban area, densely populated and with high traffic flow, by analyses of environmental matrices: soil and Quercus ilex leaves. Being some PAHs demonstrated to have hazardous effects on human health, the accumulation of carcinogenic and toxic PAHs (expressed as B(a)Peq) was evaluated in the leaves and soil. The main sources of the PAHs were discriminated by the diagnostic ratios in the two matrices. The urban area appeared heavily contaminated by PAHs, showing in soil and leaves total PAH concentrations also fivefold higher than those from the remote area. The soil mainly accumulated heavy PAHs, whereas leaves the lightest ones. Median values of carcinogenic PAH concentrations were higher in soil (440 ng g^?1 d.w.) and leaves (340 ng g^?1 d.w.) from the urban than the remote area (60 and 70 ng g^?1 d.w., respectively, for soil and leaves). Also, median B(a)Peq concentrations were higher both in soil and leaves from the urban (137 and 63 ng g^?1 d.w., respectively) than those from the remote area (19 and 49 ng g^?1 d.w., respectively). Different from the soils, the diagnostic ratios found for the leaves discerned PAH sources in the remote and urban areas, highlighting a great contribution of vehicular traffic emission as main PAH source in the urban area.     

Polycyclic aromatic hydrocarbon composition in soils and sediments of high altitude lakes

Polycyclic aromatic hydrocarbons (PAH) in lake sediments and nearby soils of two European high mountain regions, Pyrenees and Tatra, have been studied. Similar mixtures of parent PAH were observed in all cases, indicating predominance of airborne transported combustion products. Nevertheless, the composition of these atmospherically long-range transported PAH was better preserved in the superficial layers of soils than sediments. This difference points to significant PAH degradation process, e.g. during lake water column transport, before accumulation in the latter. Post-depositional transformation was also different in both types of environmental compartments. Thus, lake sediments exhibit higher preservation of the more labile PAH involving lower degree of post-depositional oxidation. However, they also show the formation of major amounts of perylene by diagenetic transformation in the deep sections. This compound is not formed in soils where downcore enrichments of phenanthrene are observed, probably as a consequence of diagenetic aromatization of diterpenoids.     

纤维直接过滤去除原水藻类

以丙纶丝为滤料 ,以自制转鼓装置对高藻原水进行直接过滤除藻试验。结果表明 ,对Chl a及藻总数的去除率分别为 64 %— 95 % (平均 91% )和 82 %— 96% (平均 92 % ) ,对主要藻种的平均去除率均在 85 %以上 ,除藻效果明显。原水中藻类特征、试验运行工况条件直接影响对藻类的去除效果。筛分截留与吸附 -絮凝是试验装置过滤除藻的主要机理     

In field arsenic removal from natural water by zero-valent iron assisted by solar radiation

An in situ arsenic removal method applicable to highly contaminated water is presented. The method is based in the use of steel wool, lemon juice and solar radiation. The method was evaluated using water from the Camarones River, Atacama Desert in northern Chile, in which the arsenic concentration ranges between 1000 and 1300 μg L⁻¹. Response surface method analysis was used to optimize the amount of zero-valent iron (steel wool) and the citrate concentration (lemon juice) to be used. The optimal conditions when using solar radiation to remove arsenic from natural water from the Camarones river are: 1.3 g L⁻¹ of steel wool and one drop (ca. 0.04 mL) of lemon juice. Under these conditions, removal percentages are higher than 99.5% and the final arsenic concentration is below 10 μg L⁻¹. This highly effective arsenic removal method is easy to use and inexpensive to implement.     

Polycyclic aromatic hydrocarbons in sewage,mussels and tap water

Polycyclic aromatic hydrocarbons (PAH) have been determined in sewage discharge, mussels and tap water by glass capillary gas chromatography. Up to 30 PAH compounds have been identified. The concentration levels are low, respectively 0.8 – 7.7μg/1, 0.5–1.1 μg/g and 0.002 – 0.2μg/1 of sum PAH have been determined in sewage discharge, mussels and tap water. The accumulation rate in mussels seems to be rather slow at the ambient water concentrations.     

Polycyclic aromatic hydrocarbon burden in ambient air in selected Niger Delta communities in Nigeria

The Niger Delta area in Nigeria has major oil producing and refining centers that characterized enormous industrial activities, especially in the petroleum sector. These industrial processes release different kinds of atmospheric pollutants, of which there is paucity of information on their levels and health implications. The objective of this study was to determine the ambient levels of polycyclic aromatic hydrocarbons (PAHs) in communities of a local government area (Eleme) where oil wells, petrochemical installations, a refinery, and a fertilizer complex are located. Respirable particulate matter (PM) in air were collected using Anderson high-volume sampler with PM with aerodynamic diameter > 10 microm (PM10) inlet for collecting filterable, particle-bound PAHs according to standard methods. PAHs were analyzed following standard methods for the 16 World Health Organization (WHO) prioritized components. The results were compared against the levels in another local government area (Ahoada East) with low industrial presence. The average total PAH concentration in Eleme of 9.2 microg/m3 was among the highest in the world; by contrast, the average concentration in Ahoada East was only 0.17 ng/m3. The most prominent PAHs at Eleme were those known to be carcinogenic and included benzo(a)pyrene (1.6 x 10(4) ng/m3 at bubu), benzo(k)fluoranthene (2.4 x 10(4) ng/m3 at Akpajo where a petrochemical is located), pyrene (3.1 x 10(3) ng/m3 at Ogale), and indeno(1,2,3-cd)pyrene (9.1 x 10(3) ng/m3 at Akpajo). Data from this study emphasize the need for a comprehensive source apportionment study and an assessment of the health effects of oil production on local communities of Nigeria where no such information currently exists.     

Temperature-dependent sorption of polycyclic aromatic hydrocarbons on natural and treated sediments

In aqueous environment temperature is considered to play a significant role in the sorption process of polycyclic aromatic hydrocarbons (PAHs) and its influence on the sorption equilibrium is indicative of sorption energies and mechanisms. In this study, sorptions of five PAHs on three heterogeneous sorbents including one river sediment (YHR), one estuary sediment (YRD) and one treated sediment with organic matter removed (IM) were carried out at a range of temperature from 5 °C to 35 °C. Stronger sorptions were observed at lower temperatures, with the equilibrium sorption coefficient K_d increasing 2-5 times as the temperature decreases 30 °C. The increase of K_d value was attributed primarily to the change of PAH water solubility, which predicted 40-75% of the increase of K_d in the sorption process. To provide insight into the sorption mechanism, enthalpy change (ΔH_S) for the sorption process was calculated and the values were observed to be negative for all of the interactions, suggesting that the exothermal sorption of PAHs inversely dependents on temperature. Based on the values of ΔH_S, van der Waals forces were inferred as the main sorption mechanism for the PAHs, especially on the YHR sediment which contained more organic matter. For sorption of larger size PAHs on the sorbents with low organic matter, specific interactions were deduced to contribute to the overall sorption.     

天然有机物对零价铁去除水体中砷的影响研究

在研究零价铁对水体中砷去除动力学的基础上,着重探讨了天然有机物腐殖酸对零价铁除砷的影响.并对零价铁的腐蚀产物进行了分析.结果表明,水体中的砷可以通过在零价铁腐蚀产物上的吸附得到快速去除.腐殖酸显著降低了砷的去除率,这归因于腐殖酸与零价铁腐蚀产生的铁离子形成络合物,阻止了Fe(OH)3(或Fe(OH)2)沉淀的产生.腐殖酸浓度越高.砷的去除率越低.1.00 mg腐殖酸最多可以络合约0.75 mg铁离子.当铁离子与腐殖酸的络合达到饱和后,零价铁进一步腐蚀产生的铁离子可形成Fe(OH)3(或Fe(OH)2)沉淀,这些沉淀物可吸附水体中的腐殖酸和砷,从而加速砷的去除.冷冻干燥后的零价铁腐蚀产物的结构以无定型为主,含有少量的结晶化合物,包括γ-Fe2O3、γ-FeO(OH)和Fe3O4等.腐殖酸的存在可进一步增加腐蚀产物中的无定型成分.光电能谱(XPS)分析结果显示,吸附在腐蚀产物上的砷为5价,没有发现5价砷被还原成3价砷.在应用零价铁修复砷污染水体时,应考虑腐殖酸的影响.     

Polycyclic aromatic hydrocarbons in sediments,pore water and the amphipod Pontoporeia hoyi from Lake Michigan

Polycyclic aromatic hydrocarbon (PAH) concentrations were measured in Pontoporeia hoyi, the most abundant benthic organism in Lake Michigan, and in its associated sediment/pore water matrix. Individual PAH concentrations ranged from 10 ppb to 1 ppm in three sedimentary environments having different levels of organic carbon. Pore water concentrations appeared to be independent of sediment concentrations. P. hoyi bioconcentration factors ranged from approximately 10⁴ to 10⁵ for seven analyzed PAHs. A major fraction of the phenanthrene, fluoranthene and pyrene in P. hoyi appears to come from sediments and pore water, while chrysene and BaP are primarily obtained from water.     

Polycyclic aromatic hydrocarbons in solid residues from waste incineration

Polycyclic aromatic hydrocarbons (PAH) levels in solid residues from clinical waste incineration were measured using HPLC with fluorescence detection. PAH mass emission rates and emission rates as a function of waste burned are also reported. For bottom ash, PAH levels and physical properties were found to be quite consistent. Levels of high molecular mass PAHs were comparable to levels previously reported in the literature when adjusted for differences in sample preparation techniques. However, levels of low molecular mass PAHs were considerably elevated in this study. Possible reasons for this finding include the composition of the waste, combustion conditions and methods of sample preparation. In contrast, no PAHs were found in fly ash, an unexpected finding which is probably attributable to matrix effects resulting from a surfeit of lime in the fly ash. Factors effecting the partitioning of PAHs and their environmental fate are also discussed.     

Arsenic removal from water by chemisorption filters

The concept of multiple separation by chemisorptive filters was applied and investigated in the process of arsenic removal from water. Chemisorption filters were made by the paper manufacturing method and consisted of cellulose, cationic and anionic ion exchangers, activated carbon and a corresponding chemical agent. In this work chemisorption filters were activated with Ag+, Mg2+, Cu2+, Al3+ and Fe3+ ions, and their chemical contribution to total arsenic removal from the water was analyzed. It was concluded that Cu2+ ions exhibited the best removal effect. Using a chromatographic continuous system with multifunctional filters, which combines the effects of adsorption, ion exchange and filtration, a decrease in the arsenic concentration was determined; for an active layer of 8 mm and a contact time of 2 s it was more than 1000-fold. All processes were performed in batch and chromatographic continuous systems under equilibrium or dynamic conditions. The results of the investigations have shown that arsenic removal is valence dependent (the removal of pentavalent arsenic was more effective). The initial concentration, pH and pollutants in anionic forms, which affected the selectivity, were important for all the processes investigated. The mechanisms of pollutant removal were determined on the basis of measurements of active Cu2+ ion propagation inside the filter structure. By correlating the front propagation of active ions and the pollutant output concentration a more exact model for the removal process was obtained.     

Polycyclic aromatic hydrocarbons in lake sediments from the High Tatras

European alpine lake systems are used as indicators of air quality over the continent. Preliminary data showed high polycyclic aromatic hydrocarbons (PAH) loads in the High Tatras (Eastern Europe) in comparison to other mountain regions. Here, insight on the spatial distribution of PAH is provided from analysis of top-core sediments of 27 alpine lakes distributed along the High Tatras.Top-core sediment concentrations were higher than those in deep-cores, and they were higher than those observed in other European high mountain regions. The PAH profiles were uniform and comparable to those observed in aerosols and snow, indicating that atmospheric deposition was the predominant PAH input pathway to the lakes. Good agreement between estimated atmospheric deposition and sedimentation fluxes was observed. However, in several lakes in the western range higher sediment fluxes may correspond to higher PAH depositions levels. The higher concentrations may also reflect inputs from potential emission source areas.     

Monitoring aromatic hydrocarbon biodegradation by functional marker genes

The development of biological treatment technologies for contaminated environments requires tools for obtaining direct information about the biodegradation of specific contaminants. The potential of functional gene array analysis to monitor changes in the amount of functional marker genes as indicators of contaminant biodegradation was investigated. A prototype functional gene array was developed for targeting key functions in the biodegradation of naphthalene, toluene and xylenes. Internal standard probe based normalization was introduced to facilitate comparison across multiple samples. Coupled with one-colour hybridization, the signal normalization improved the consistency among replicate hybridizations resulting in better discrimination for the differences in the amount of target DNA. During the naphthalene biodegradation in a PAH-contaminated soil slurry microcosm, the normalized hybridization signals in naphthalene catabolic gene probes were in good agreement with the amount of naphthalene-degradation genes and the production of 14CO2. Gene arrays provide efficient means for monitoring of contaminant biodegradation in the environment.