An examination of antecedents to coal miners' hearing protection behaviors: a test of the theory of planned behavior

PROBLEM: The National Institute for Occupational Safety and Health's [NIOSH] National Occupational Research Agenda (DHHS Publication No. 96-115) reports that approximately 50% of miners will experience hearing loss by age 50, compared to only 9% of the general population. The present investigation examines three antecedents believed to be associated with miner's use of hearing protection. METHOD: A posttest-delayed-posttest-control group field research design was employed to assess antecedents toward wearing hearing protection. RESULTS: Following the initial posttest, miners' attitudes and subjective norms were antecedents to intentions to wear hearing protection devices. Also, intentions toward wearing hearing protection predicted hearing protection behaviors. Approximately six weeks later, miners' attitudes and perceived behavioral control were each significant predictors of intentions to wear hearing protection and again, intentions were positively associated with hearing protection behaviors. IMPACT ON INDUSTRY: Our results indicate that appeals to normative influences may be the most effective antecedent to employ when persuading coal miners to wear hearing protection. However, messages designed to impact attitudes and perceived behavioral control were also effective.     

Experimental mine and laboratory dust explosion research at NIOSH

This paper describes dust explosion research conducted in an experimental mine and in a 20-L laboratory chamber at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH). The primary purpose of this research is to improve safety in mining, but the data are also useful to other industries that manufacture, process, or use combustible dusts. Explosion characteristics such as the minimum explosible concentration and the rock dust inerting requirements were measured for various combustible dusts from the mining industries. These dusts included bituminous coals, gilsonite, oil shales, and sulfide ores. The full-scale tests were conducted in the Lake Lynn experimental mine of NIOSH. The mine tests were initiated by a methane–air explosion at the face (closed end) that both entrained and ignited the dust. The laboratory-scale tests were conducted in the 20-L chamber using ignitors of various energies. One purpose of the laboratory and mine comparison is to determine the conditions under which the laboratory tests best simulate the full-scale tests. The results of this research showed relatively good agreement between the laboratory and the large-scale tests in determining explosion limits. Full-scale experiments in the experimental mine were also conducted to evaluate the explosion resistance characteristics of seals that are used to separate non-ventilated, inactive workings from active workings of a mine. Results of these explosion tests show significant increases in explosion overpressure due to added coal dust and indications of pressure piling.     

Reducing non-contact electric arc injuries: an investigation of behavioral and organizational issues

PROBLEM: It is estimated that 5 to 10 arc flash explosions occur in electric equipment every day in the United States. In the mining industry the largest single injury category of electrical injuries are caused by non-contact electrical arcs. METHOD: This investigation progressed in two phases: (a) 836 Mine Safety and Health Administration (MSHA) reports of electric arcing incidents that occurred over a period of 11 years were reviewed, and (b) personal interviews were conducted with 32 individuals. A theoretical Safe Job Performance Model guided the study. RESULTS: Behavioral dimensions were identified and included the effect of worker experience, judgment and decision-making ability, behavioral and organizational controls, and safety culture. SUMMARY: The National Institute for Occupational Safety and Health (NIOSH) conducted an investigation of behavioral components associated with arc flash incidents and developed recommendations for interventions based on findings. IMPACT ON INDUSTRY: This study fills a vacuum in electrical training with a focus on the organizational and behavioral aspects of arc flash incidents. The research is cross-cutting in its scope, in that the results apply not only to mining and construction, but many other industries employing electricians. Although the majority of mine electrical injuries are the results of burns from electrical arcs, few miners are aware that such a hazard exists. A safety training program, which includes a video and an instructor's discussion guide, was developed for electricians based on this study's findings. "Arc Flash Awareness" was released in 2007 (DHHS NIOSH Publication No.2007-116D) and is available through 1-800 CDC INFO. Phone: 1-800 232-4636 or email cdcinfo@cdc.gov. It is also available from MSHA at MSHADistribution@dol.gov or 304-256-3257 (DVD-576). Private industry is producing Portuguese and Spanish language translations.     

The NIOSH Construction Program: Research to practice, impact, and developing a National Construction Agenda

The U.S. National Institute for Occupational Safety and Health (NIOSH) conducts research to improve and protect the health and safety of workers. This paper describes the experience of the NIOSH Construction Program with two recent program planning initiatives intended to improve the program: (a) an independent external review of work over the past decade and (b) the development of strategic goals organized into a “National Construction Agenda” to guide a decade of future work. These goals, developed with input from construction industry stakeholders and researchers, are a part of the NIOSH National Occupational Research Agenda (NORA) initiative. The NORA goals are intended to provide an ambitious set of goals for all construction stakeholders to work together on. Both efforts relate to insuring the relevance and impact of research, reflecting an emerging policy perspective that research programs should be judged not just by the quality and quantity of science produced, but by the industry impact and tangible benefit resulting from the research. This paper describes how views on research planning have evolved to incorporate lessons learned about how research leads to improved safety and health for workers. It also describes the process used to develop the goals and the resulting strategic and intermediate goals that comprise the National Construction Agenda.     

职业噪声危害控制的对策——“听力保护计划纲要(草案)”要点

分析了国内职业噪声危害和控制的现状,提出有效控制我国职业噪声危害的途经是制定并执行有效的听力保护计划。还详细给出了“听力保护计划纲要(草案)”的要点。该纲要(草案)是劳动部劳动保护科学研究所根据国内外在听力保护方面的多年经验,并结合我国国情起草的。此纲要(草案)在北京清河毛纺厂试点,业已取得明显效果。     

Comparison of two fatal occupational injury surveillance systems in the United States

INTRODUCTION: Using different methods, two national systems compile fatal occupational injury data in the United States: the National Institute for Occupational Safety and Health (NIOSH) National Traumatic Occupational Fatalities (NTOF) surveillance system, and the Bureau of Labor Statistics (BLS) Census of Fatal Occupational Injuries (CFOI). The NTOF uses only death certificates, while CFOI uses multiple sources for case ascertainment. METHODS: Through overall and case-by-case comparisons, this study compares these systems and evaluates counts for the nation and by state for worker and case characteristics. RESULTS: From 1992 through 1994, NTOF reported an average of 84% of the number of traumatic occupational fatalities reported in CFOI. This percentage changed somewhat when a case-by-case comparison was conducted--88% of the NTOF cases were matched directly to the CFOI cases. Although CFOI captured a larger number of fatalities annually, the additional fatalities did not follow a discernable pattern. IMPACT ON INDUSTRY: By understanding the distribution of fatalities, targeted efforts to reduce them will benefit all industries.     

化肥行业噪声危害调查及治理评价

通过对７家大中型化肥厂的噪声调查，分析了化肥行业中的噪声源特性和岗位噪声暴露状况。对１６０１名作业工人进行了体检并得出了噪声危害和岗位噪声的剂量──反应关系。还对各厂已采取的噪声治理措施进行了技术评价。最后，根据化肥行业的特点，提出了降低噪声和加强听力保护的几点建议。     

我国职业噪声危害成因分析及总体控制对策

职业噪声不仅属于职业卫生问题 ,也是当今世界上主要的环境公害之一。有效控制职业噪声不仅能够保护劳动者的听力不受损害 ,使其身心安全与健康得到保障 ,同时也是消除安全隐患 ,实现安全生产的重要途径。笔者分析了我国职业噪声危害的现状 ,论述了我国职业噪声危害的严重性以及控制的重要性与迫切性。然后采用“人 -机 -环境”系统工程方法 ,分别从人的行为、物的状态以及工作环境等 3个方面 ,分析职业噪声危害的成因 ,构造了基于宏观管理维、中观人机环境维以及微观技术维等三维结构的我国职业噪声危害控制总体框架 ,并从政府、企业以及劳动者等角度 ,对职业噪声危害控制的运行机制进行了研究 ,以解决我国日益严重的职业噪声危害问题 ,不断改善我国安全生产现状并进一步提高劳动保护工作的整体水平。     

The potential impact of light emitting diode lighting on reducing mining injuries during operation and maintenance of lighting systems

Research by the US National Institute for Occupational Safety and Health (NIOSH) indicates that light emitting diodes (LEDs) can be used to enhance safety by improving a miner’s ability to see mining hazards and reducing glare. This paper investigates if LEDs provide another benefit by reducing miner exposure to hazards during maintenance and operation of LED lighting. LEDs could provide useful lives up to 50 times longer than incandescent lighting commonly used in mining and could enable design changes to reduce certain hazards. The mining accident records compiled by the Mine Safety and Health Administration (MSHA) were examined to determine the extent and nature of accidents involving the maintenance and operation of mine luminaries. A total of 140 relevant accident records were found for the years 2002–2006. These incidents resulted in 3668 days lost from work with an additional 925 days of restricted activity. The injury narratives were studied to determine if the implementation of LED-based luminaries could reduce injury severity and frequency. The greatest near-term potential impacts appear to be related to reducing maintenance and cap lamp redesign. Longer term (5 years), low-power and lightweight auxiliary LED lighting for surface mines could also have potential impact for improving safety.     

An Evaluation of the NIOSH Lifting Equation: A Psychophysical and Biomechanical Investigation

Using the results of psychophysical and biomechanical experiments, NIOSH (National Institute for Occupational Safety and Health) Recommended Weight Limit (RWL), the Lifting Index (LI), the form of the asymmetry multiplier, and the criterion for compression force were investigated. Analysis of the results indicated a significant difference between the NIOSH RWL and the reported Maximum Acceptable Weight of Lift (MAWL). Contrary to the NIOSH lifting equation, the form of the asymmetry multiplier was found to be non-linear. The overall average of peak compression force on the L5/S1 was 3685 N. Fifty-eight percent of all compression forces reported in the biomechanical experiment were found to exceed the suggested 3400 N set by NIOSH guidelines. These results support previous research findings on the validity of NIOSH guidelines.     

Particle size and surface area effects on explosibility using a 20-L chamber

The Mine Safety and Health Administration (MSHA) specification for rock dust used in underground coal mines, as defined by 30 CFR 75.2, requires 70% of the material to pass through a 200 mesh sieve (<75 μm). However, in a collection of rock dusts, 47% were found to not meet the criteria. Upon further investigation, it was determined that some of the samples did meet the specification, but were inadequate to render pulverized Pittsburgh coal inert in the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) 20-L chamber. This paper will examine the particle size distributions, specific surface areas (SSA), and the explosion suppression effectiveness of these rock dusts. It will also discuss related findings from other studies, including full-scale results from work performed at the Lake Lynn Experimental Mine. Further, a minimum SSA for effective rock dust will be suggested.     

Low back pain among residential carpenters: ergonomic evaluation using OWAS and 2D compression estimation.

Occupational low back pain (LBP) remains a leading safety and health challenge. This cross-sectional investigation measured the prevalence of LBP in residential carpenters and investigated ergonomic risk factors. Ninety-four carpenters were investigated for LBP presence and associated risk factors. Ten representative job-tasks were evaluated using the Ovako Working Posture Analysis System (OWAS) and ErgoMaster 2D software to measure elements of posture, stress, and risk. Job-tasks were found to differ significantly for total lumbar compression and shear at peak loading (p < .001), ranging from 2 956 to 8 606 N and 802 to 1 974 N respectively. OWAS indicated that slight risk for injury was found in 10 job-tasks while distinct risk was found in 7 of the 10 job-tasks. Seven of the 10 job-tasks exceeded the National Institute for Occupational Safety and Health (NIOSH) action limit of 3 400 N for low back loading. The point prevalence for LBP was 14% while the annual prevalence was 38%.     

Evaluation of sound exposure and risk of hearing impairment in orchestral musicians

This study aimed to assess exposure to sound and the risk of noise-induced hearing loss (NIHL) in orchestral musicians. Sound pressure level was measured in 1 opera and 3 symphony orchestras; questionnaires were filled in. On the basis of that data, the risk of NIHL was assessed according to Standard No. ISO 1999:1990. Classical orchestral musicians are usually exposed to sound at equivalent continuous A-weighted sound pressure levels of 81?90 dB (10th?90th percentiles), for 20?45 h (10th?90th percentiles) per week. Occupational exposure to such sound levels over 40 years of employment might cause hearing loss (expressed as a mean hearing threshold level at 2, 3, 4 kHz exceeding 35 dB) of up to 26%. Playing the horn, trumpet, tuba and percussion carries the highest risk (over 20%).     

Low Back Pain Among Residential Carpenters: Ergonomic Evaluation Using OWAS and 2D Compression Estimation

Occupational low back pain (LBP) remains a leading safety and health challenge. This cross-sectional investigation measured the prevalence of LBP in residential carpenters and investigated ergonomic risk factors. Ninety-four carpenters were investigated for LBP presence and associated risk factors. Ten representative job-tasks were evaluated using the Ovako Working Posture Analysis System (OWAS) and ErgoMaster? 2D software to measure elements of posture, stress, and risk. Job-tasks were found to differ significantly for total lumbar compression and shear at peak loading (p < .001), ranging from 2 956 to 8 606 N and 802 to 1 974 N respectively. OWAS indicated that slight risk for injury was found in 10 job-tasks while distinct risk was found in 7 of the 10 job-tasks. Seven of the 10 job-tasks exceeded the National Institute for Occupational Safety and Health (NIOSH) action limit of 3 400 N for low back loading. The point prevalence for LBP was 14% while the annual prevalence was 38%.     

Path forward: Emerging issues and challenges

The NIOSH Construction Program worked with industry stakeholders to develop a National Occupational Safety and Health Construction Agenda to target future research and activities. The Program and its partners are also cognizant that new developments can emerge over time and that research can play an important role in helping to understand and address these emerging issues. Examples of emerging issues relevant to construction safety and health are described. These include: (a) climate change and energy considerations; (b) green construction developments and opportunities; (c) new materials; (d) changes in industry structure and practice; (e) workforce developments and disparities; (f) injury underreporting and cost and risk shifting; and (g) increased interest in addressing root causes. Responding to emerging issues while maintaining a focus on fundamental longstanding issues represents an ongoing challenge for researchers and industry organizations. Additional research to understand the diffusion and adoption of research by the industry is also needed. Research accomplished to date provides a strong foundation for addressing future industry needs and trends.     

Explosion temperatures and pressures of metals and other elemental dust clouds

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) conducted a study of the explosibility of various metals and other elemental dusts, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafnium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties—from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly “refractory” elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechnic ignitors. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from 1550 K for tin and tungsten powders to 2800 K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures.     

Collecting representative dust samples: A comparison of various sampling methods in underground coal mines

Former methods used in the U.S. to assess hazardous and explosible coal dust date back to the 1950s. As mining technologies advanced, so too have the hazards. Given the results of the recent coal dust particle size survey and full-scale experimental mine explosion tests, the National Institute for Occupational Safety and Health (NIOSH) recommended a new minimum standard, in the absence of background methane, of 80% total incombustible content (TIC) be required in the intake airways of bituminous coal mines, replacing the previous 65% TIC requirement. Most important to monitoring and maintaining the 80% TIC is the ability to effectively collect and analyze representative dust samples that would likely disperse and participate in dust explosion propagation. Research has shown that dust suspended on elevated surfaces is usually finer, more reactive, and more readily dispersible while floor deposits of dust are generally coarser and more difficult to disperse given the same blast of air. The roof, rib, and floor portions of the dust samples were collected and analyzed for incombustible content separately and the results were compared to a band sample of the roof, rib, and floor components. Results indicate that the roof and rib dust samples should be kept separate from floor dust samples and considered individually for analyses. The various experimental collection methods are detailed along with preferred sampling approaches that improve the detectability of potentially hazardous accumulations of explosible dust.     

电子工业脉冲噪声对工人健康影响的调查研究

对电子行业接触脉冲噪声的冲压工进行了调查，其脉冲噪声水平波动在１０２～１１２ｄＢ（八）之间（峰值），对作业工人听力已产生不同程度的损伤，心电图在中高工龄组有改变。还分析了脉冲噪声引起听力损失与暴露时间有密切关系。提出了进一步加强安全监督管理的对策。     

Epidemiological and biomechanical evaluation of airline baggage handling

Objectives. Musculoskeletal disorders (MSDs) are prevalent among airline baggage handlers due to manual materials handling. In this study, the Nordic musculoskeletal questionnaire (NMQ), the revised National Institute for Occupational Safety and Health (NIOSH) lifting equation, and the University of Michigan 3D Static Strength Prediction Program? (3DSSPP) were used to analyze MSDs among baggage handlers. Methods. The NMQ was filled out by 209 baggage handlers and 46 arbitrarily selected baggage handlers were evaluated using the NIOSH method and 3DSSPP. Results. The obtained results showed that the most common MSDs occurred in the lower back region. The next risky regions included knees, neck, and upper back, respectively. The NIOSH results confirmed that the subjects lifted loads heavier than the permitted limit and their lifting postures were inappropriate. The results of the 3DSSPP also indicated that compression forces exceeded the NIOSH limit in these awkward postures. Conclusions. Relying on this study, holding compulsory ergonomic lifting training courses could be proposed for workers and regulations adjusting an upper limit for maximum baggage weight must be also enacted in order to improve occupational health and prevent the prevalence of increasing MSDs.