Determination of vapour pressures of nine organic chemicals adsorbed on silicagel

The vapour pressures of nine organic chemicals adsorbed on silicagel were determined by a method which can be standardized. They were compared with those of the non-absorbed, free compounds (range 6 × 10⁻³ – 7 × 10⁴ Pa).     

Leaching of atrazine, metolachlor and diuron in the field in relation to their injection depth into a silt loam soil

A field experiment was conducted on a Calcaric Cambisol soil to study the consequences of the penetration depth and properties of pesticides on the risk of subsequent leaching. Three pesticides with different mobility characteristics and bromide were injected at 30 cm (where soil organic matter (OM) was 2%) and 80 cm (soil OM 0.5%) on irrigated plots without a crop. The migration of injected solutes was assessed for two years by sampling the soil solution using six porous cups installed at 50 and 150 cm depth and by relating solute contents to drainage water flux estimated by the STICS model (Simulateur mulTIdisciplinaire pour les Cultures Standard). Pesticides injected at 30 cm were strongly retained so that no metolachlor or diuron was detected at 50 and 150 cm. The ratio of atrazine peak concentration in the soil solution to concentration in the injected solution (C/C₀) was 1 × 10⁻³ and 0.2 × 10⁻³, respectively, at 50 and 150 cm. When injected at 80 cm, (C/C₀) of atrazine, metolachlor and diuron were 10 × 10⁻³, 1 × 10⁻³ and 0.3 × 10⁻³ at 150 cm, respectively; 1/(C/C₀) was correlated with K_oc values reported from databases. The ratio of drainage volume to the amount of water at field capacity in the soil layer between the injection point at 30 cm and the water sampling level (V/V₀) at 50 and 150 cm was 0.6 and 0.9, respectively, for bromide and 1.6 and 1.0 for atrazine. V/V₀ of the injected solutes at 80 cm was for bromide, atrazine, metolachlor and diuron 0.6, 0.9, 1.2 and 1.7, respectively; pesticide V/V₀ was correlated with K_oc. The retardation factor was a good indicator of migration risk, but tended to overestimate retardation of molecules with high K_oc. Atrazine desorption represented an additional leaching risk as a source of prolonged low contamination. The large variability in soil solution of bromide and pesticide concentrations in the horizontal plane was attributed to flow paths and clods in the tilled soil layer. This heterogeneity was assumed to channel water fluxes into restricted areas and thereby increase the risk of groundwater contamination. The methodology used in the field proves to provide consistent results.     

Kinetics of nitromusk compounds degradation in water by ultraviolet radiation and hydrogen peroxide

The photodegradation of five representative nitromusk compounds in water has been performed in a stirred batch photoreactor with a UV low-pressure immersed mercury lamp, at constant temperature and different doses of hydrogen peroxide. The rate constants have been calculated on the basis of experimental data and a postulated first-order kinetic model. The rate constants, at 298 K and a dose of 1.1746 μmol l⁻¹ H₂O₂ ranges from 0.3567 × 10⁻³ s⁻¹ for musk tibetene, to 1.785 × 10⁻³ s⁻¹ for musk ambrette.     

Concentrations of chlorine, bromine and iodine in Japanese rivers

Concentrations of halogens (Cl, Br and I) in 30 Japanese rivers were measured by ion chromatography and inductively coupled plasma mass spectrometry to understand their behavior in the terrestrial environment. Concentrations of Cl, Br and I in each river, obtained at 10 sampling points from the upper stream to the river mouth, tended to increase near the river mouth. The ranges of geometric means of Cl, Br and I in each river were 1.0–19.4 mg l⁻¹, 2.5–67.9 μg l⁻¹, and 0.18–8.34 μg l⁻¹, respectively. To compare halogen behavior, the concentration ratios, Br/Cl and I/Cl, were calculated. The Br/Cl range was (2.3–7.8) × 10⁻³ (geometric mean: 3.74 × 10⁻³), and it was nearly constant except for the Yoneshiro river. It was estimated that 60–80% of total Br in the middle to lower parts of this river was the excess Br. The Br chemical form in all the rivers is generally considered to be Br⁻. The I/Cl ratios had different trends in rivers flowing into the Japan Sea and Pacific Ocean, possibly due to the different geological features in the river catchments.     

Distribution of pesticides and heavy metals in trophic chain

Determination of triazines herbicides (atrazine and simazine) by high performance liquid chromatography (HPLC) in samples of trophic chain were worked out. Determination limits of 0.5 μg g⁻¹ for atrazine, 0.8 μg g⁻¹ for simazine with pesticides recovery of 70–77% in trophic chain samples were obtained. The content of simazine in soils was in range 1.72–57.89 μg g⁻¹, in grass 5–88 μg g⁻¹, in milk 2.32–15.29 μg g⁻¹, in cereals 10.98–387 μg g⁻¹, in eggs 30.14–59.48 μg g⁻¹, for fruits: 2.45–6.19 μg g⁻¹. The content of atrazine in soils was in range 0.69–19.59 μg g⁻¹, in grass 7.85–23.85 μg g⁻¹, in cereals 1.88–43.08 μg g⁻¹. Cadmium, lead and zinc were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) in the same samples as atrazine and simazine. Determination limits for cadmium 5 × 10⁻³ μg g⁻¹, for lead 1 × 10⁻² μg g⁻¹, and for zinc 0.2 × 10⁻³ μg g⁻¹, were obtained. The content of cadmium in soil was in range 0.13–5.89 μg g⁻¹, in grass 114–627.72 × 10⁻³ μg g⁻¹, in milk 8.88–61.88 × 10⁻³ μg g⁻¹, in cereals 0.20–0.31 μg g⁻¹, in eggs 0.11–0.15 μg g⁻¹, in fruits 0.23–0.59 μg g⁻¹. The content of lead in soils was in range 0.57–151.50 μg g⁻¹, in grass 0.16–136.57 μg g⁻¹, in milk 1.16–3.74 μg g⁻¹, in cereals 1.05–5.47 μg g⁻¹, in eggs 5.79–55.87 μg g⁻¹, in fruits 21.00–87.36 μg g⁻¹. Zinc content in soil was in range 9.15–424.5 μg g⁻¹, in grass 35.20–55.87 μg g⁻¹, in milk 20.00–34.38 μg g⁻¹, in cereals 14.94–28.78 μg g⁻¹, in eggs 15.67–32.01 μg g⁻¹, in fruits 14.94–18.88 μg g⁻¹.

Described below extraction and mineralization methods for particular trophic chains allowed to determine of atrazine, simazine, cadmium, lead and zinc with good repeatability and precision. Emphasis was focused on liquid–liquid extraction and solid-phase extraction of atrazine and simazine from analysed materials, as well as, on monitoring the content of herbicides and metals in soil and along trophic chain. Higher concentration of pesticides in samples from west region of Poland in comparison to that of east region is likely related to common applying them in Western Europe in relation to East Europe. The content of metals strongly depends on samples origin (industry area, vicinity of motorways).     

Parameters for predicting fate of organochlorine pesticides in the environment (I) Octanol-water and air-water partition coefficients

Octanol-water partition coefficients and air-water partition coefficients of 10 principal organochlorine pesticides were obtained as basic data for predicting their fate in environment. The octanol-water partition coefficients were in the wide range from 10 to 10⁶ and approximately correlated with the solubilities in water. The air-water partition coefficients were also in the wide range from 10⁻⁷ to 10⁻², and the values for chloropicrin, dichlorvos, DCIP and quintozene were relatively high.     

Specific biomagnification of polychlorinated dibenzo-p-dioxins and dibenzofurans in tufted ducks (Aythya fuligula), common cormorants (Phalacrocorax carbo) and their prey from Lake Shinji,Japan

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDDs/DFs) were detected in waterfowl such as common cormorants, tufted ducks, and their prey, namely fish and bivalves from Lake Shinji, Japan. The concentration of total PCDDs/DFs-TEQ was found to be higher in the muscle tissues of common cormorants than in those of tufted ducks. The results of hierarchical cluster analysis implied that the residue distribution pattern of PCDD/DF homologues was considerably different between these two species. Furthermore, biomagnification factors (BMFs) were estimated from bivalves as prey to tufted duck muscles as target organs. Despite the highest concentrations of 1,3,6,8- and 1,3,7,9-TeCDD in tufted ducks and their prey, however, the BMFs of these isomers were calculated to be lower than those of the toxic 2,3,7,8-substituted PCDDs/DFs. On the other hand, log BMF of toxic 2,3,7,8-substituted PCDDs/DFs were significantly higher for lower chlorinated isomers than those of the higher chlorinated isomers. The biota-sediment accumulation factors (BSAFs) of PCDDs/DFs were also estimated using shijimi clam and fish samples against sediment from Lake Shinji. The average BSAFs were estimated and ranged from 4.0×10⁻³ to 2.2×10⁻¹ and 2.0×10⁻⁴ to 2.0×10⁻¹ for bivalve and fish samples, respectively. Based on calculated BMFs and BSAFs, the total PCDD/DF-TEQ levels in the tufted duck were estimated to have been lowest (2.0 pg TEQ/g dry weight basis) in 1947 and highest (9.8 pg TEQ/g) in 1971.     

Reaction of arsenic vapor species with fly ash compounds: kinetics and speciation of the reaction with calcium silicates

In coal combustion systems, the partitioning of arsenic between the vapor and solid phases is determined by the interaction of arsenic vapors with fly ash compounds under post-combustion conditions. This partitioning is affected by gas–solid reactions between the calcium components of the ash particles and arsenic vapors. In this study, bench scale experiments were conducted with calcium compounds typical of coal-derived fly ash to determine product formation, the extent of reaction and reaction rates when contacted by arsenic oxide vapors. Experiments conducted with arsenic trioxide (As₄O_6(g)) vapors in contact with calcium oxide, di-calcium silicate and mono-calcium silicate over the temperature range 600–1000 °C indicated that these solids were capable of reacting with arsenic vapor species in both air and nitrogen. Calcium arsenate was the observed reaction product in all the samples analyzed. Maximum capture of arsenic occurred at 1000 °C with calcium oxide being the most effective of the three solids over the range of temperatures studied. Using a shrinking core model for a first order reaction and the results from intrinsic kinetic experiments conducted in air, the reaction rate constants were found to be 1.4×10⁻³exp(−2776/T) m/s for calcium oxide particles, 7.2×10⁻³exp(−3367/T) m/s for di-calcium silicate particles and 5.5×10⁻³exp(−3607/T) m/s for mono-calcium silicate particles. These results therefore suggest that any calcium present in fly ash can react with arsenic vapor and capture the metal in water-insoluble forms of the less hazardous As(V) oxidation state.     

Copper complexation by tannic acid in aqueous solution

The speciation of titrated copper in a dissolved tannic acid (TA) solution with an initial concentration of 4 mmol organic carbon (OC)/l was investigated in a nine-step titration experiment (Cu/OC molar ratio = 0.0030–0.0567). We differentiated between soluble and insoluble Cu species by 0.45 μm filtration. Measurements with a copper ion selective electrode (ISE) and diffusive gradients in thin films (DGT) were conducted to quantify unbound Cu(II) cations (‘free’ Cu) and labile soluble Cu complexes. For the DGT measurements, we used an APA hydrogel and a Chelex 100 chelating resin (Na form). Insoluble organic Cu complexes (>0.45 μm) was the dominant Cu species for Cu/OC = 0.0030–0.0567 with a maximum fraction of 0.96 of total Cu. At Cu/OC > 0.0100, Cu-catalysed degradation of aggregate structures resulted in a strong increase of free Cu and (labile) soluble Cu complexes with a maximum fraction of 0.28 and 0.32 of total Cu, respectively. Labile (i.e. DGT-detectable) soluble Cu complexes had a relatively high averaged diffusion coefficient (D) in the APA hydrogel (3.50 × 10⁻⁶– 5.58 × 10⁻⁶ cm² s⁻¹).     

Determination of 99Tc deposited on the ground within the 30-km zone around the Chernobyl reactor and estimation of 99Tc released into atmosphere by the accident

Technetium-99 was determined in samples from the 30-km zone around the Chernobyl reactor. Concentrations of ⁹⁹Tc in soil samples taken from three forest sites ranged from 1.1 to 14.1 Bq kg⁻¹ dry weight for the organic soil layers, and from 0.13 to 0.83 Bq kg⁻¹ dry weight for the mineral soil layers. In particular, for the organic layers, the measured ⁹⁹Tc concentrations were one or two orders of magnitude higher than those due to global fallout ⁹⁹Tc. The ⁹⁹Tc depositions (Bq m⁻²), based on the sum of the depositions measured in organic and mineral layers, ranged from 130 Bq m⁻² within the 10-km zone to about 20 Bq m⁻² close to the border of the 30-km zone. Taking the corresponding measured ¹³⁷Cs depositions into account, it was found that the activity ratio of ⁹⁹TW/¹³⁷Cs ranged from 6 × 10⁻⁵ to 1.2 × 10⁻⁴. It was estimated that about 970 GBq of ⁹⁹Tc had been released by the Chernobyl accident. This figure corresponded to 2%–3% of the total ⁹⁹Tc inventory in the core.     

Cold season CH4, CO2 and N2O fluxes from freshwater marshes in northeast China

Cold season (winter and thaw) CH₄, CO₂ and N₂O fluxes from freshwater marshes (47°35′N, 133°31′E, Northeast China) were measured, using the static chamber method. The mean CH₄ and CO₂ fluxes from Carex lasiocarpa (Cl) were 0.5 ± 0.19 and 6.23 ± 1.36 mg C m⁻² h⁻¹, respectively, and those from Deyeuxia angustifoli (Da) were 0.18 ± 0.15 and 5.22 ± 2.48 mg C m⁻² h⁻¹, respectively in winter. There was no significant difference between Cl and Da (p > 0.05). The contributions of winter CH₄ fluxes were about 5.5% and 3% in the Cl and Da, respectively. Marshes are an important potential N₂O sink in winter season in northeast China. During thaw, the CH₄ and CO₂ emissions rapidly increased, 4.5–6 times of winter emissions. Wetland became a source of N₂O. Cold season gases flux from northern wetlands play an important role in the seasonal gas exchange.     

Electrochemical oxidation of benzene on boron-doped diamond electrodes

This work presents an electrochemical investigation of the benzene oxidation process in aqueous solution on boron-doped diamond (BDD) electrodes. Additionally, in order to determine the main products generated during the oxidation process, electrolysis and high performance liquid chromatography experiments were carried out. The complete degradation of this compound was performed aiming to a further application in waste water treatment. The cyclic voltammetry studies indicate that benzene is irreversibly oxidized in acid medium (H₂SO₄ 0.5 M) on the BDD electrode surface at 2.0 V versus Ag/AgCl in a diffusion controlled process. During the cycling, other products are generated, and a pair of peaks was observed that can be associated with the oxi-reduction of anyone of the following species: hydroquinone, benzoquinone, resorcinol or catechol. The electrolysis experiments were carried out at 2.4 and 2.5 V on the BDD electrode surface in a solution containing 1 × 10⁻² M of benzene (below the saturation concentration in aqueous solution), for 3 and 5 h, respectively. The main products measured were: hydroquinone, resorcinol, p-benzoquinone, catechol and phenol. The complete electrochemical benzene degradation was performed in the electrolysis experiments using a rotating BDD disc electrode (2.5 V for 5 h) and the main products detected were all measured at concentrations lower than 10⁻⁵ M in this condition. The boron-doped diamond electrode had proved to be a valuable tool for the electrochemical degradation of the benzene, a very stable chemical compound.     

Release flux of mercury from different environmental surfaces in Chongqing, China

An investigation was conducted to estimate mercury emission to the atmosphere from different environmental surfaces and to assess its contribution to the local mercury budget in Chongqing, China. Mercury flux was measured using dynamic flux chamber (DFC) at six soil sites of three different areas (mercury polluted area, farmland and woodland) and four water surfaces from August 2003 to April 2004. The mercury emission fluxes were 3.5 ± 1.2–8.4 ± 2.5 ng m⁻² h⁻¹ for three shaded forest sites, 85.8 ± 32.4 ng m⁻² h⁻¹ for farming field, 12.3 ± 9.8–733.8 ± 255 ng m⁻² h⁻¹ for grassland sites, and 5.9 ± 12.6–618.6 ± 339 ng m⁻² h⁻¹ for water surfaces. Mercury exchange fluxes were generally higher from air/water surfaces than from air/soil surfaces. The mercury negative fluxes were found in tow soil sites at overcast days (mean = −6.4 ± 1.5 ng m⁻² h⁻¹). The diurnal and seasonal variations of mercury flux were observed in all sites. The mercury emission responded positively to the solar radiation, but negatively to the relative humidity. The mercury flux from air/soil surfaces was significantly correlated with soil temperature, which was well described by an Arrhenius-type expression with activation energy of 31.1 kcal mol⁻¹. The annual mercury emission to the atmosphere from land surface is about 1.787 t of mercury in Chongqing.     

Qualitative and quantitative cancer risk assessment of 2, 3, 7, 8-tetrachloro-dibenzo-p-dioxin (2, 3, 7, 8-TCDD)

The carcinogenicity of 2,3,7,8-TCDD at multiple organ sites in animals has been well established by several cancer bioassays. Results of two of the most notable of these, the Kociba et al. (1978) rat feeding study and the National Toxicology Program (1980) gavage study in rats and mice showed hepatocellular carcinomas in two strains of female rats and male and female mice. Other tumor sites included carcinomas of the lung, tongue, hard palate and nasal turbinates, thyroid, and subcutaneous tissue. The evidence for carcinogenicity of 2,3,7,8-TCDD in animals is regarded as “sufficient” using the classification system of the International Agency for Research on Cancer (IARC).

Two Swedish epidemiologic case-control studies (Hardell and Sandstrom, 1979; Eriksson et al. 1979, 1981) reported a significant five- to sevenfold excess risk of soft-tissue sarcomas (STS) from occupational exposure to chlorinated phenoxyacetic acid herbicides and/or chlorophenols. Additionally, several small cohort studies collectively exhibited an unusual cluster of STS, significantly increased over combined expected incidence. Problems with these studies do not appear to be sufficient to discount this excess risk. The human evidence alone for the carcinogenicity of 2,3,7,8-TCDD is “inadequate” using the IARC classification. However, for 2,3,7,8-TCDD in combination with chlorinated phenoxyacetic acid herbicides and/or chlorophenols, the human evidence is considered to be “limited.” The overall evidence for carcinogenicity considering both animal and human studies would place 2,3,7,8-TCDD alone in the IARC category 2B, meaning that the substance is probably carcinogenic in humans. The overall weight of evidence for 2,3,7,8-TCDD in combination with chlorinated phenoxyacetic acid herbicides and/or chlorophenols is regarded as IARC category 2A, also meaning that they are probably carcinogenic for humans.

Using current EPA methodology for quantitatively estimating cancer risks, several animal data sets have been analyzed. Comparing the results, the upper-limit incremental unit risk estimate is 1.6 × 10⁻² for a lifetime exposure of 1 ng/kg/day. This estimate is derived from a lifetime feeding study (Kociba et al., 1978) in which 2,3,7,8-TCDD induced tumors of the liver, lungs, hard palate, and nasal turbinates in female rats. Incremental unit cancer risks are also extrapolated for lifetime 2,3,7,8-TCDD exposures in water and air. Based on continuous lifetime exposure to 1 ng/L 2,3,7,8-TCDD in drinking water, the upper-limit estimate of extra cancer risk per individual is 4.5 × 10⁻³. For lifetime exposure to 1 pg 2,3,7,8-TCDD/m³ in the ambient air, the upper-limit individual risk is 3.3 × 10⁻⁵.     

Short-term toxicity of pyraclofos used as a blackfly larvicide on non-target aquatic fauna in a tropical environment

Among the many larvicides tested for the control of s.l. larvae, the vector of human onchocerciasis in West Africa, pyraclofos proved to be 100% effective at 100 μg × L⁻¹ for 10 min in river, with a carry of 20 km at 100 m³ × sec⁻¹. Tests were then performed both in laboratory and field conditions to evaluate its toxicity on the non-target aquatic fauna. In experimental short-term gutter tests, the detachment of the total benthic insects was 35% at 100 μg × L⁻¹ for 10 min against 17% for temephos at the same dose and 59% for chlorphoxim at 50μg × L⁻¹ for 10 min. , and were the most affected organisms. The treatment of a river resulted in a considerable detachment of the same taxonomic groups, plus Orthocladiinae. On the other hand, investigations conducted in tanks showed that the 24-hr LC₅₀ for is 150 μg × L⁻¹ and that for 170 μg × L⁻¹, values which are not very different from the operational dose of the larvicide (100 μg × L⁻¹ for 10 min.). Nevertheless, in a river, no fish mortality was recorded. Based on fish LC₅₀ and drift of benthic insects, pyraclofos at 100 μg × L⁻¹ was judged to be less toxic to aquatic fauna in the short term than permethrin and carbosulfan.     

Mercury deposition through litterfall in an Atlantic forest at Ilha Grande, Southeast Brazil

Atmospheric Hg transfer to the forest soil through litterfall was investigated in a primary rainforest at Ilha Grande (Southeast Brazil) from January to December 1997. Litter mass deposition reached 10.0 t ha⁻¹ y⁻¹, with leaves composing 50–84% of the total litter mass. Concentrations of Hg in the total fallen litter varied from 20 to 244 ng g⁻¹, with higher concentrations during the dry season, between June and August (225 ± 17 ng g⁻¹), and lower concentrations during the rainy season (99 ± 54 ng g⁻¹). This seasonal variability was reflected in the Hg flux through litterfall, which corresponded to a Hg input to the forest floor of 122 μg m⁻² y⁻¹, with average Hg deposition of 16.5 ± 1.5 μg m⁻² month⁻¹ during and just after the dry season (June–September) and 7.0 ± 3.6 μg m⁻² month⁻¹ in the rest of the year. The variability in meteorological conditions (determining atmospheric Hg availability to foliar scavenging) may explain the pulsed pattern of Hg deposition, since litterfall temporal variability was generally unrelated with such deposition, except by a peak in litterfall production in September. Comparisons with regional data on Hg atmospheric deposition show that litterfall promotes Hg deposition at Ilha Grande two to three orders of magnitude higher than open rainfall deposition in non-industrialized areas and approximately two times higher than open rainfall deposition in industrialized areas in Rio de Janeiro State. The observed input suggests that atmospheric Hg transfer through litterfall may explain a larger fraction of the total Hg input to forest soils in Southeast Brazil than those recorded at higher latitudes.     

Determination of dithiocarbamate fungicide propineb and its main metabolite propylenethiourea in airborne samples

A simple, rapid and sensitive GC–MS method for the determination of dithiocarbamate fungicide propineb [polymeric zinc propylenebis (dithiocarbamate)] and an improved HPLC procedure for the simultaneous determination of its main metabolite, propylenethiourea, and ethylenethiourea, the main metabolite of all ethylenedithiocarbamates, in airborne samples are described. The method for the analysis of propineb involves the evolution of carbon disulfide (CS₂), under acidic conditions in the presence of stannous chloride, extraction of the generated CS₂ into a layer of isooctane which is then analyzed for CS₂ content by GC–MS in SIM mode. Under the optimum conditions, the retention time of CS₂ was 1.89 min and the total time of chromatographic analysis was 5 min. Recoveries from spiking glass microfibre filters (GF/A) and silica gel filters were 86 ± 7 (n = 9) and 89 ± 4 (n = 9), respectively. The limit of detection is 0.7 ng per filter, which is equivalent to about 0.8–1.0 ng m⁻³ in air. In parallel, an HPLC method with ultraviolet detection is presented for the simultaneous analysis of the metabolites. Separation of the two metabolites was attained in less than 5 min. Recoveries from spiking GF/A and silica gel filters for ethylenethiourea were 100 ± 1 (n = 3) and 98 ± 2 (n = 3), respectively, while for propylenethiourea were 102 ± 1 (n = 3) and 98 ± 1 (n = 3), respectively. The detection limits are about 36–43 and 40–49 ng m⁻³ in air for ethylenethiourea and propylenethiourea, respectively. All the analytes spiked in the filters are proven to be stable for more than one month, at −4 °C.     

Copper complexation by dissolved organic matter and uncertainty assessment of their stability constants

The interaction of Cu with dissolved organic matter (DOM, extracted from an organic forest floor) was investigated and the resulting data was evaluated in terms of their uncertainty. The speciation of Cu over ‘free’ Cu (as analysed by diffusive gradients in thin films (DGT)), dissolved Cu–DOM complexes and precipitated Cu–DOM was determined as a function of pH (3.5, 4.0 and 4.5) and Cu/C ratio. The dissolved organically bound fraction was highest at pH 4.5, but this fraction decreased with increasing Cu/C ratio, which was observed for all pH levels. In the range of Cu/C=7×10⁻⁵–2.3×10⁻² (mol/mol) the precipitated fraction was very small. The speciation of both Al and Fe was not affected by increasing Cu concentrations. From a continuous distribution model using the Scatchard approach, we calculated the optimal fit and corresponding upper and lower 95% uncertainty bounds of the overall stability constants (K_o) with the shuffled complex evolution Metropolis (SCEM) algorithm. Although the optimal equation fitted the data very well, the uncertainty of the, according to literature, most reliable approach to establish stability constants, was still large. Accordingly, the usually reported intrinsic stability constants exhibited large uncertainty ranging from logK_i=6.0–7.1 (optimal 6.7) for pH 3.5, logK_i=6.5–7.1 (optimal 6.8) for pH 4.0, and logK_i=6.4–7.2 (optimal 6.8) for pH 4.5 and showed only little effect of pH.     

Decomposition of chlorinated dioxins, odourous compounds and NOx from MSW incineraton plant by oxidizing catalyst

An experiment was carried out to decompose chlorinated dioxins (PCDDs, PCDFs) Chlorobenzenes, NOx and odourous compounds (H₂S, CH₄S, C₂H₆S₂, C₈H₈, C₂H₆S, C₂H₄O, NH₃) simultaneously using a catalyst in the MSW incineration plant. The experiments were conducted at temperatures from 200°C to 400°C and from 3000h⁻¹ to 6000h⁻¹ at space velocity. A catalyst containing V₂O₅ and WO₃ on the basis of TiO₂ is used, an oxidizing catalyst of the honeycomb type. The average decomposition efficiencis were 95%, 98%, 92% for PCDDs(48CDDs), PCDFs(48CDFs) and Chlorobenzenes(36CLBs) at a reaction temperature of 350°C and a space velocity of 3000h⁻¹, more than 90% for NOx at a reactiont temperature of 300°C and more than 80% for odourous compounds at the reaction temperature of 300°C and a space velocity of 6000h⁻¹. All those compounds were decomposed successfully with increasing contact time and surface. The rate-determing step was the chemical reaction of catalyst surface.     

Synchronous-scan fluorescence spectra of Chlorella vulgaris solution

The characterization of the Chlorella vulgaris solution was carried out using synchronous-scan spectroscopy. The range of concentration of algae and Fe(III) in aqueous solutions were 5 × 10⁸–8 × 10⁹ cells l⁻¹ and 10–60 μM, respectively. Effective characterization method used was synchronous-scan fluorescence spectroscopy. The wavelength difference (Δλ) of 90 nm was maintained between excitation and emission wavelengths; 90 nm was found to be the best Δλ for effective characterization of Chlorella vulgaris solution with or without quencher species (e.g., Fe(III), humic acid (HA)) for the first time. The peak was observed at about EX 236.6 nm/EM 326.6 nm for synchronous-scan fluorescence spectra. The fluorescence quenching of algae in system of algae–Fe(III)–HA was studied using synchronous-scan spectroscopy for the first time. Fe(III) was clearly the effective quencher. The relationship between I₀/I (quenching efficiency) and c (concentration of Fe(III) added) was a linear correlation for the algae solution with Fe(III). Also, Aldrich humic acid was found to be an effective quencher. pH effect on synchronous-scan fluorescence intensity of algal solution with Fe(III) and/or HA was evident.