组合氯化消毒工艺的卤代消毒副产物生成特性

比较4种单独使用氯或组合氯化消毒工艺在较长管网停留时的卤代消毒副产物生成情况.4种工艺为单独游离氯消毒、氯胺消毒、清水池游离氯消毒后转氯胺的先氯后氨消毒、短时游离氯后转氯胺的顺序氯化消毒工艺.结果表明,游离氯消毒工艺在管网停留时间长时,卤代消毒副产物会持续大量的生成,而一氯胺消毒工艺生成的卤代消毒副产物量很低.目前使用较为普遍的先氯后氨消毒工艺与游离氯消毒相比,可以降低卤代消毒副产物的生成量,管网停留24 h时,三卤甲烷的生成量降低了9.6%,卤乙酸的生成量减低了42%.但是先氯后氨消毒工艺由于游离氯接触时间约为2 h,卤代消毒副产物已经大量生成.短时游离氯后转氯胺的顺序氯化消毒工艺,由于控制了游离氯的接触时间,可以在保障消毒工艺灭活微生物效果的同时更为有效地控制卤代消毒副产物,管网停留24 h时,三卤甲烷的生成量与单独游离氯消毒工艺相比降低了48%,卤乙酸的生成量减低了72%.因此,顺序氯化消毒工艺可以更好地控制卤代消毒副产物的生成,提高水质安全性.     

新型溴代苯酚类消毒副产物的氯化降解机制

最近,13种新型极性卤代苯酚类消毒副产物在氯化消毒后的饮用水中被发现,它们按结构被分成4组,分别是二卤-4-羟基苯甲醛、二卤-4-羟基苯甲酸、二卤水杨酸和三卤苯酚.为研究它们在氯化消毒过程中的降解机制,选取了其中的4种全溴代种类,即3,5-二溴-4-羟基苯甲醛、3,5-二溴-4-羟基苯甲酸、3,5-二溴水杨酸以及2,4,6-三溴苯酚,利用UPLC/ESI-tq MS中的前体离子扫描,多反应监测和子离子扫描,鉴定了这几种消毒副产物在氯化消毒过程中的中间产物以及终产物,并根据这些中间产物和终产物与消毒时间的关系推测了其降解路径.结果表明,除了3,5-二溴水杨酸相对较稳定外,其余3种消毒副产物在氯化消毒过程中不稳定,通过取代、水解以及氧化等过程最终降解为卤乙酸等脂肪族小分子消毒副产物.在降解过程中有许多中间产物被检测并鉴定出来,其中包含一组具有五元环结构的新型消毒副产物(三卤代-羟基环戊烯二酮).     

水中天然有机物的分类特性及其卤代活性

利用XAD树脂对原水中的天然有机物进行富集分类 ,将其分为腐植酸、富里酸、亲水酸和其它亲水物质等 4种有机组分 .考察了原水中各有机组分的分布及其在加氯消毒过程中的三卤甲烷生成量、生成速度及耗氯量情况 .研究结果表明 ,原水中的主要成分是富里酸 ,占有机物总量的50.7% ,其它3种成分所占比例相对较小 ;原水具有较高的三卤甲烷生成能力 ,富里酸是生成三卤甲烷的主要有机组分 ;对各有机组分卤代活性的研究表明 ,腐植酸、富里酸和亲水酸具有较高的卤代活性 ,其它亲水物质的卤代活性较低 ;从各有机组分的三卤甲烷生成速度及与氯反应速度来看 ,腐植酸、富里酸及亲水酸具有较快的三卤甲烷生成速度 ,与氯的反应速度也较快 ,而其它亲水物质的三卤甲烷生成速度及与氯的反应速度均较低 .     

臭氧预氧化对藻细胞及胞外分泌物消毒副产物生成势的影响

以处于对数生长期后期的悦目颤藻为研究对象,研究了藻细胞及胞外分泌物对氯化消毒副产物生成势(DBPFP)的贡献,以及臭氧预氧化对DBPFP的影响规律,即不同臭氧投量及预氧化时间对DBPFP的影响,并探讨臭氧预氧化控制消毒副产物生成势的原因.研究表明,藻细胞和胞外分泌物的三卤甲烷类副产物都主要是氯仿和一溴二氯甲烷,卤乙酸类副产物都主要是二氯乙酸和三氯乙酸.颤藻细胞和其EOM本身及经臭氧预氧化混凝后形成卤乙酸的能力基本都高于形成三卤甲烷的能力,在实际含藻水的处理中,应该更加重视对卤乙酸的控制.臭氧预氧化可以降低胞外分泌物形成氯化消毒副产物(DBP)的能力,且随着反应时间延长,DBPFP降低越多.在本试验条件下,0.975 mg/L臭氧预氧化10min后混凝,可比单纯混凝降低胞外分泌物DBPFP 31%,其中HAAFP降低52.6%,而THMFP却升高12.5%,可见臭氧预氧化控制胞外分泌物DBPFP主要原因是其可以很好地控制卤乙酸生成势.同时臭氧预氧化会使含藻细胞水样的DBPFP大幅度升高,且随着氧化时间延长,各种氯化消毒副产物生成势几乎呈线性增加.在实际水处理中,应在去除藻细胞之后再进行臭氧氧化以控制DBPFP.     

J市饮用水氯消毒副产物分析及其健康风险评价

J市位于太湖下游,其水源水质受上游和自身工农业发展的影响,有机物和氨氮浓度较高,氯消毒副产物及其引发的健康风险广泛受到关注.2012年5、8、10月以及2013年1月采样,使用气相色谱法分析了J市饮用水中4种三卤甲烷和5种卤乙酸的含量,发现自来水中三卤甲烷浓度占三卤甲烷与卤乙酸总和的88.1%以上,5月、8月和次年1月浓度较高(分别为39.34、50.37和28.02μg.L-1),10月浓度(19.19μg.L-1)较低,远高于卤乙酸的浓度(2.58～4.02μg.L-1).自来水煮沸3min后,三卤甲烷可去除92.3%以上,但卤乙酸会大幅度增加.基于EPA推荐的健康风险评价模型对经口摄取途径时氯消毒副产物的致癌和非致癌风险进行计算,发现化学致癌物质的健康风险为3.1×10-6～7.3×10-6,高于可接受风险水平1×10-6;煮沸后致癌物质的健康风险大幅度降低至7.9×10-7,低于可接受风险水平.煮沸后非致癌氯消毒副产物的健康风险由2.1×10-11显著升高至3.4×10-9,未超过10-5的风险管理参考值.     

两点短时游离氯后转氯胺的顺序氯化消毒工艺研究

基于顺序氯化消毒工艺的原理,采用两点短时游离氯后转氯胺的两点顺序氯化消毒工艺,即在过滤和清水池前的两点分别加氯,并在清水池加氯后立即加氨转化为氯胺消毒的工艺,该工艺在常规处理工艺的给水厂进行了消毒试验.结果表明,加氯点的适当提前,不仅有利于控制消毒副产物的生成量,而且有效抑制了滤池中的生物膜滋生.两点顺序氯化消毒工艺中生成的卤代消毒副产物比相同条件下一次性加入等量的氯消毒剂的消毒方法产生的三卤甲烷(THMs)平均减少了51.6％,卤乙酸(HAAs)平均减少了46.7％.细菌学指标HPC的结果也显示出了该工艺在保障水质的微生物安全方面的优势.     

氯消毒过程中水中色氨酸产生THMs和HAAs的特征研究

以氨基酸为代表的溶解性含氮有机物在水源水中广泛存在,成为制水工艺消毒副产物的主要前体物之一.选取色氨酸（Trp）为含氮前体物模型,考察了其在消毒工艺中产生受控消毒副产物的途径及影响因素.结果表明,Trp氯化过程经取代,脱羧,水解等一系列反应,可生成卤乙酸（HAAs）,三卤甲烷（THMs）等消毒副产物.THMs和HAAs的生成量随加氯量增加;随接触时间的延长逐渐增加.温度的升高,HAAs的生成量先增大后减少;碱性条件有利于THMs和HAAs的生成.氯胺消毒和遮光条件下可明显减少THMs和HAAs的产生.     

取代苯甲酸在天然河流中的生物降解及其定量结构--生物降解性相关研究

以天然河流水作为微生物源 ,采用碘量法测定了 2 0种苯甲酸类化合物的 5日生化需氧量 ,并以其占理论需氧量的百分数作为表征生物降解性的参数 ,得出各类取代苯甲酸类化合物的生物降解能力为 :羟基 >氨基 >羧基 >甲氧基 >氯基 >硝基 ;对于同一种取代基 ,对位取代基化合物生物降解能力最大 ,而邻位、间位取代基化合物生物降解能力大体相同。计算了苯甲酸类化合物的分子连接性指数 ,并以 5日生化需氧量占理论需氧量的百分数为参数建立了 QSBR模型。分析结果表明 ,分子连接性指数5Xvpc、5Xp- 5Xvp 能较好地反映取代苯甲酸的生物降解性     

KMnO4-PAC对高原喀斯特湖库DOM的DBPsFP控制

以云贵高原典型喀斯特湖库红枫湖取水口溶解性有机质（DOM）为研究对象,调查不同组合方式下高锰酸钾-聚合氯化铝（KMnO₄-PAC）对消毒副产物的生成潜能（DBPsFP）变化和平均组成分布,并通过红外光谱（FTIR）和三维荧光光谱（3D-EEM）对部分样品进行化学表征,推断其影响机制.结果表明：在0.1,0.2,0.4mg/L KMnO₄投加量下,DBPsFP降低17.5~73%,DOM的卤代活性化学结构和官能团部分被有效钝化;PAC的网捕和卷扫效应使DBPsFP进一步减少27.9~86.1%,组合工艺对DBPs的生成潜能影响大小为：三卤甲烷（THM₄） > 卤乙酸（HAA₉） > 卤乙腈（HAN₄）/卤代酮（HK₂）/三氯硝基甲烷（TCNM）.FTIR的结果表明预氧化后3300cm^-1处的透过率降低,指纹区1000~1300cm^-1处的峰频提升,表明分子中的O-H、COOH和C-O官能团增加,共轭不饱和结构在KMnO₄作用下部分消失.3D-EEM验证了外源有机物（腐殖酸）在DOM中占比随KMnO₄浓度梯度升高而下降,同时类蛋白结构的吸收峰强度增加,说明最终DBPs贡献可能源于DOM中剩余的小分子类蛋白（氨基酸）.     

水中脲类除草剂Chlortoluron氯化产物鉴定、降解途径探究

对不同pH下Chlortoluron氯化后生成的非挥发性中间产物和挥发性产物进行了研究。对Chlortoluron氯化后的非挥发性中间产物的UPLC-ESI-MS鉴定发现了m/z为213、229、263、281、和247的离子,分析表明它们分别是Chlortoluron及其一羟基、一氯羟基、二氯和一氯衍生物。对Chlortoluron氯化后的挥发性产物采用吹扫补集-GC-MS进行分析鉴定发现了三氯甲烷(CF)、二氯硝基甲烷(DCNM)、二氯乙腈(DCAN)、1,1-2-二氯丙酮(1,1-DCP)、三氯硝基甲烷(TCNM)和1,1,1-2-三氯丙酮(1,1,1-TCP)六种消毒副产物。根据本研究中的实验结果分析和推测,在Chlortoluron的氯化过程中,苯环上和脲基链上都经历了羟基化、氧化和取代反应,接着苯环被打破,随后生成了更为有害的副产物,基于此,本文推断了Chlortoluron的氯化降解途径。     

Formation of regulated and unregulated disinfection byproducts during chlorination and chloramination: Roles of dissolved organic matter type, bromide, and iodide

Algal blooms and wastewater effluents can introduce algal organic matter (AOM) and effluent organic matter (EfOM) into surface waters, respectively. In this study, the impact of bromide and iodide on the formation of halogenated disinfection byproducts (DBPs) during chlorination and chloramination from various types of dissolved organic matter (DOM, e.g., natural organic matter (NOM), AOM, and EfOM) were investigated based on the data collected from literature. In general, higher formation of trihalomethanes (THMs) and haloacetic acids (HAAs) was observed in NOM than AOM and EfOM, indicating high reactivities of phenolic moieties with both chlorine and monochloramine. The formation of haloacetaldehydes (HALs), haloacetonitriles (HANs) and haloacetamides (HAMs) was much lower than THMs and HAAs. Increasing initial bromide concentrations increased the formation of THMs, HAAs, HANs, and HAMs, but not HALs. Bromine substitution factor (BSF) values of DBPs formed in chlorination decreased as specific ultraviolet absorbance (SUVA) increased. AOM favored the formation of iodinated THMs (I-THMs) during chloramination using preformed chloramines and chlorination-chloramination processes. Increasing prechlorination time can reduce the I-THM concentrations because of the conversion of iodide to iodate, but this increased the formation of chlorinated and brominated DBPs. In an analogous way, iodine substitution factor (ISF) values of I-THMs formed in chloramination decreased as SUVA values of DOM increased. Compared to chlorination, the formation of noniodinated DBPs is low in chloramination.     

氯、氯胺消毒下钱江源水源水消毒副产物形成特征研究

以钱江源水源水为研究对象,以氯、氯胺为消毒方式,研究了不同消毒条件下,三卤甲烷(THMs)、卤乙腈(HANs)、氯代酮(CKs)、二卤乙酸(DHAAs)、三卤乙酸(THAAs)等消毒副产物(DBPs)的形成情况,以便为水务工作者监测钱江源建库前后水质、DBPs形成的变化提供基础数据.结果显示,氯消毒下DBPs的产量比氯胺消毒高出3~7倍甚至1个数量级,但不管是氯消毒还是氯胺消毒,THMs、HAAs形成量均在我国饮用水标准范围内.氯消毒下,大部分DBPs产量为中、碱性条件酸性条件(除了CKs),氯胺消毒则呈现不同的情况(所有DBPs的产量均为p H=6、p H=7p H=8).消毒剂量对所有DBPs形成具有明显的促进作用;溴离子对THMs、DHANs、DHAAs的形成有明显的促进作用.进一步研究表明,钱江源水源水的水质比钱塘江下游九溪水源水好,DBPs形成也较低,某些指标(如有机碳、有机氮、HANs形成量等)甚至比同省水质较好的金兰水库还要好;而且由于其较高的比紫外吸收值(SUVA),DBPs的溴嵌入能力均比九溪水源水、金兰水库低.此外,就目前的钱江源水源水来说,控制消毒剂量(氯、或氯胺)是控制DBPs形成的有效策略.     

饮用水消毒副产物分析及相关研究进展

饮用水消毒副产物（DBPs）是消毒剂和一些天然有机物（NOM）反应生成的化合物,主要包括三卤甲烷（THMs）、卤代G@（HAAs）、卤代乙腈（HANs）和致诱变化舍物（MX）4类。本文针对氯、氯胺、二氧化氯、臭氧4种主要消毒方式产生的消毒副产物,讨论了有关分析技术的发展过程,从DBPs的前处理技术、分析技术等角度,介绍了DBPs研究领域近期所取得的进展,并展望了今后研究的发展方向。     

Effect of ferric and bromide ions on the formation and speciation of disinfection byproducts during chlorination

The e ects of ferric ion, pH, and bromide on the formation and distribution of disinfection byproducts (DBPs) during chlorination were studied. Two raw water samples from Huangpu River and Yangtze River, two typical drinking water sources of Shanghai, were used for the investigation. Compared with the samples from Huangpu River, the raw water samples from Yangtze River had lower content of total organic carbon (TOC) and ferric ions, but higher bromide concentrations. Under controlled chlorination conditions, four trihalomethanes (THMs), nine haloacetic acids (HAAs), total organic halogen (TOX) and its halogen species fractions, including total organic chlorine (TOCl) and total organic bromide (TOBr), were determined. The results showed that co-existent ferric and bromide ions significantly promoted the formation of total THMs and HAAs for both raw water samples. Higher concentration of bromide ions significantly changed the speciation of the formed THMs and HAAs. There was an obvious shift to brominated species, which might result in a more adverse influence on the safety of drinking water. The results also indicated that high levels of bromide ions in raw water samples produced higher percentages of unknown TOBr.     

Formation potentials of typical disinfection byproducts and changes of genotoxicity for chlorinated tertiary effluent pretreated by ozone

The effects of ozonation on the formation potential of typical disinfection byproducts (DBPs) and the changes of genotoxicity during post chlorination of tertiary effluent from a sewage treatment plant were investigated. Ozonation enhanced the yields of all detected chlorine DBPs except CHCl3. At a chlorine dose of 5 mg/L, the three brominated THMs and five HAAs increased, while chloroform decreased with the increase of ozone dose from 0 to 10 mg/L (ozone dose in consumption base). At a chlorine dose of 10 ...     

A balancing act: Optimizing free chlorine contact time to minimize iodo-DBPs, NDMA, and regulated DBPs in chloraminated drinking water

Many drinking water treatment plants in the U.S. have switched from chlorination to chloramination to lower levels of regulated trihalomethane (THM) and haloacetic acid (HAA) disinfection byproducts (DBPs) in drinking water and meet the current regulations. However, chloramination can also produce other highly toxic/carcinogenic, unregulated DBPs: iodo-acids, iodo-THMs, and N-nitrosodimethylamine (NDMA). In practice, chloramines are generated by the addition of chlorine with ammonia, and plants use varying amounts of free chlorine contact time prior to ammonia addition to effectively kill pathogens and meet DBP regulations. However, iodo-DBPs and nitrosamines are generally not considered in this balancing of free chlorine contact time. The goal of our work was to determine whether an optimal free chlorine contact time could be established in which iodo-DBPs and NDMA could be minimized, while keeping regulated THMs and HAAs below their regulatory limits. The effect of free chlorine contact time was evaluated for the formation of six iodo-trihalomethanes (iodo-THMs), six iodo-acids, and NDMA during the chloramination of drinking water. Ten different free chlorine contact times were examined for two source waters with different dissolved organic carbon (DOC) and bromide/iodide. For the low DOC water at pH 7 and 8, an optimized free chlorine contact time of up to 1 h could control regulated THMs and HAAs, as well as iodo-DBPs and NDMA. For the high DOC water, a free chlorine contact time of 5 min could control iodo-DBPs and NDMA at both pHs, but the regulated DBPs could exceed the regulations at pH 7.     

太湖、钱塘江取水口底泥及周边土壤有机物形成消毒副产物的特征研究

底泥、土壤均是水体有机物的重要来源,但目前相关消毒副产物(DBPs)形成方面的研究偏少.本研究以长三角重要水源地太湖、钱塘江取水口的底泥和周边土壤的浸出液为研究对象,探索氯、臭氧+氯、氯胺、臭氧+氯胺4种消毒方式下,三卤甲烷(THMs)、卤代酮(HKs)、卤乙腈(HANs)、卤代硝基甲烷(HNMs)的形成情况.结果表明,太湖、钱塘江取水口的底泥、周边土壤有机物的芳香度均很低(SUVA254(即比紫外吸光值)2),与腐殖质(Sigma)相比,底泥、土壤有机物不是氯消毒中THMs的重要前驱物,但却是HANs特别是HNMs的重要前驱物.相比氯消毒,氯胺消毒能大幅降低土壤、底泥有机物THMs、HKs、HANs、HNMs的生成量,而且也可抑制含溴DBPs的形成.臭氧预处理大幅提高了氯、氯胺消毒中HKs、HNMs的产量,但对THMs、HANs则不一定.太湖、钱塘江的土壤、底泥存在一定的溴污染,但不管是哪种消毒方式,均是HNMs的溴嵌入因子最大.     

Characteristics of molecular weight distribution of dissolved organic matter in bromide-containing water and disinfection by-product formation properties during treatment processes

The characteristics of dissolved organic matter (DOM) and bromide ion concentration have a significant influence on the formation of disinfection by-products (DBPs). In order to identify the main DBP precursors, DOM was divided into five fractions based on molecular weight (MW), trihalomethane formation potential and haloacetic acid formation potential were determined for fractions, and the change in contents of different fractions and total DBPs during treatment processes (pre-chlorination, coagulation, sand filtration, disinfection) were studied. Moreover, the relationship between bromide concentration and DBP generation characteristics in processes was also analyzed. The results showed that the main DBP precursors were the fraction with MW < 1 kDa and fraction with MW 3−10 kDa, and the DBP''s generation ability of lower molecular weight DOM (< 10 kDa) was higher than that of higher molecular weight DOM. During different processes, pre-chlorination and disinfection had limited effect on removing organics but could alter the MW distribution, and coagulation and filtration could effectively remove organics with higher MW. For DBPs, trihalomethanes (THMs) were mainly generated in pre-chlorination and disinfection, while haloacetic acids (HAAs) were mostly generated during pre-chlorination; coagulation and sand filtration had little effect on THMs but resulted in a slight removal of HAAs. In addition, the results of ANOVA tests suggested that molecular sizes and treatment processes have significant influence on DBP formation. With increasing bromide concentration, the brominated DBPs significantly increased, but the bromine incorporation factor in the processes was basically consistent at each concentration.     

Formation potentials of typical DBPs and changes of genotoxicity for chlorinated tertiary effluent pretreated by ozone

The effects of ozonation on the formation potential of typical disinfection byproducts (DBPs) and the changes of genotoxicity during post chlorination of tertiary effluent from a sewage treatment plant were investigated. Ozonation enhanced the yields of all detected chlorine DBPs except CHCl3. At a chlorine dose of 5 mg/L, the three brominated THMs and five HAAs increased, while chloroform decreased with the increase of ozone dose from 0 to 10 mg/L (ozone dose in consumption base). At a chlorine dose of 10 mg/L, the two mixed bromochloro species THMs and two dominant HAAs (DCAA and TCAA) firstly increased and then decreased with the increase of ozone dose, with the turning point approximately occurring at an ozone dose of 5 mg/L. The genotoxicity detected using umu test, on the other hand, was removed from 7 μg 4-NQO/L to a negligible level by ozonation under an ozone dose of 5 mg/L. Chlorination could further remove the genotoxicity to some extent. It was found that SUVA (UV absorbance divided by DOC concentration) might be used as an indicative parameter for monitoring the removal of genotoxicity during the oxidation.