Numerical simulation of chemical looping combustion process with CaSO4 oxygen carrier

Chemical-looping combustion (CLC) is a promising technology for the combustion of gas or solid fuel with efficient use of energy and inherent separation of CO₂. The technique involves the use of an oxygen carrier which transfers oxygen from combustion air to the fuel, and hence a direct contact between air and fuel is avoided. A chemical-looping combustion system consists of a fuel reactor and an air reactor. A metal oxide is used as oxygen carrier that circulates between the two reactors. The air reactor is a high velocity fluidized bed where the oxygen carrier particles are transported together with the air stream to the top of the air reactor, where they are then transferred to the fuel reactor using a cyclone. The fuel reactor is a bubbling fluidized bed reactor where oxygen carrier particles react with hydrocarbon fuel and get reduced. The reduced oxygen carrier particles are transported back to the air reactor where they react with oxygen in the air and are oxidized back to metal oxide. The exhaust from the fuel reactor mainly consists of CO₂ and water vapor. After condensation of the water in the exit gas from the fuel reactor, the remaining CO₂ gas is compressed and cooled to yield liquid CO₂, which can be disposed of in various ways.With the improvement of numerical methods and more advanced hardware technology, the time needed to run CFD (Computational fluid dynamics) codes is decreasing. Hence multiphase CFD-based models for dealing with complex gas-solid hydrodynamics and chemical reactions are becoming more accessible. Until now there were a few literatures about mathematical modeling of chemical-looping combustion using CFD approach. In this work, the reaction kinetics model of the fuel reactor (CaSO₄ + H₂) was developed by means of the commercial code FLUENT. The bubble formation and the relation between bubble formation and molar fraction of products in gas phase were well captured by CFD simulation. Computational results from the simulation also showed low fuel conversion rate. The conversion of H₂ was about 34% partially due to fast, large bubbles rising through the reactor, low bed temperature and large particles diameter.     

Chemical-looping with oxygen uncoupling for combustion of solid fuels

Chemical-looping with oxygen uncoupling (CLOU) is a novel method to burn solid fuels in gas-phase oxygen without the need for an energy intensive air separation unit. The carbon dioxide from the combustion is inherently separated from the rest of the flue gases. CLOU is based on chemical-looping combustion (CLC) and involves three steps in two reactors, one air reactor where a metal oxide captures oxygen from the combustion air (step 1), and a fuel reactor where the metal oxide releases oxygen in the gas-phase (step 2) and where this gas-phase oxygen reacts with a fuel (step 3). In other proposed schemes for using chemical-looping combustion of solid fuels there is a need for an intermediate gasification step of the char with steam or carbon dioxide to form reactive gaseous compounds which then react with the oxygen carrier particles. The gasification of char with H₂O and CO₂ is inherently slow, resulting in slow overall rates of reaction. This slow gasification is avoided in the proposed process, since there is no intermediate gasification step needed and the char reacts directly with gas-phase oxygen. The process demands an oxygen carrier which has the ability to react with the oxygen in the combustion air in the air reactor but which decomposes to a reduced metal oxide and gas-phase oxygen in the fuel reactor. Three metal oxide systems with suitable thermodynamic properties have been identified, and a thermal analysis has shown that Mn₂O₃/Mn₃O₄ and CuO/Cu₂O have suitable thermodynamic properties, although Co₃O₄/CoO may also be a possibility. However, the latter system has the disadvantage of an overall endothermic reaction in the fuel reactor. Results from batch laboratory fluidized bed tests with CuO and a gaseous and solid fuel are presented. The reaction rate of petroleum coke is approximately a factor 50 higher using CLOU in comparison to the reaction rate of the same fuel with an iron-based oxygen carrier in normal CLC.     

Design study of a 150 kWth double loop circulating fluidized bed reactor system for chemical looping combustion with focus on industrial applicability and pressurization

Nowadays the lab scale feasibility of the chemical looping combustion technology has been proved. This article deals with many of the design requirements that need to be fulfilled to make this technology applicable at industrial scale. A design for a 150 kW_th chemical looping combustion reactor system is proposed. In the base case it is supposed to work with gaseous fuels and inexpensive oxygen carriers derived from industrial by-products or natural minerals. More specifically the fuel will be methane and a manganese ore will be the basis for the oxygen carrier. It is a double loop circulating fluidized bed where both the air reactor and the fuel reactor are capable to work in the fast fluidization regime in order to increase the gas solids contact along the reactor body. High operational flexibility is aimed, in this way it will be possible to run with different fuels and oxygen carriers as well as different operating conditions such as variation in air excess. Compactness is a major goal in order to reduce the required solid material and possibly to enclose the reactor body into a pressurized vessel to investigate the chemical looping combustion under pressurized conditions. The mass and heat balance are described, as well as the hydrodynamic investigations performed. Most design solutions presented are taken from industrial standards as one main objective is to meet commercial requirements.     

Operating experience with chemical looping combustion in a 120 kW dual circulating fluidized bed (DCFB) unit

This study presents first operating experience with a 120 kW chemical looping pilot rig. The dual circulating fluidized bed reactor system and its auxiliary units are discussed. Two different oxygen carriers, i.e. ilmenite, which is a natural iron titanium ore, and a designed Ni-based particle, are tested in the CLC unit. The pilot rig is fueled with H₂, CO and CH₄ respectively at a fuel power of 65–145 kW. High solids circulation, very low solids residence time and low solids inventory are observed during operation. Owing to the scalability of the design concept, these characteristics should be quite similar to those of commercial CLC power plants. Ilmenite shows a high potential for the combustion of H₂-rich gases (e.g. from coal gasification with steam). The H₂ conversion is quite high but there is still a high potential for further improvement. The Ni-based oxygen carrier achieves the thermodynamic maximum H₂ and CO conversion and also very high CH₄ conversion. A variation of the air/fuel ratio and the reaction temperature indicates that the Ni/NiO ratio of the particle has an influence on the performance of the chemical looping combustor. Generally, low solids conversion in air and fuel reactors is observed in almost any conditions. Despite a very low H₂O/CH₄ molar ratio, no carbon formation is observed.     

Chemical-looping combustion using syngas as fuel

Chemical-looping combustion (CLC) is a combustion technology where an oxygen carrier is used to transfer oxygen from the combustion air to the fuel, avoiding direct contact between air and fuel. Thus, CO₂ and H₂O are inherently separated from the rest of the flue gases and the carbon dioxide can be obtained in a pure form without the use of an energy intensive air separation unit. The paper presents results from a 3-year project devoted to developing the CLC technology for use with syngas from coal gasification. The project has focused on: (i) the development of oxygen carrier particles, (ii) establishing a reactor design and feasible operating conditions and (iii) construction and operation of a continuously working hot reactor. Approximately, 300 different oxygen carriers based on oxides of the metals Ni, Fe, Mn and Cu were investigated with respect to parameters, which are important in a CLC system, and from these investigations, several particles were found to possess suitable qualities as oxygen carriers. Several cold-model prototypes of CLC based on interconnected fluidized bed reactors were tested, and from these tests a hot prototype CLC reactor system was constructed and operated successfully using three carriers based on Ni, Fe and Mn developed within the project. The particles were used for 30–70 h with combustion, but were circulated under hot conditions for 60–150 h.     

Effect of gas composition in Chemical-Looping Combustion with copper-based oxygen carriers: Fate of sulphur

Chemical-Looping Combustion (CLC) is an emerging technology for CO₂ capture because separation of this gas from the other flue gas components is inherent to the process and thus no energy is expended for the separation. Natural or refinery gas can be used as gaseous fuels and they may contain different amounts of sulphur compounds, such as H₂S and COS. This paper presents the combustion results obtained with a Cu-based oxygen carrier using mixtures of CH₄ and H₂S as fuel. The influence of H₂S concentration on the gas product distribution and combustion efficiency, sulphur splitting between the fuel reactor (FR) and the air reactor (AR), oxygen carrier deactivation and material agglomeration was investigated in a continuous CLC plant (500 W_th). The oxygen carrier to fuel ratio, ?, was the main operating parameter affecting the CLC system. Complete fuel combustion were reached at 1073 K working at ? values ≥1.5. The presence of H₂S did not produce a decrease in the combustion efficiency even when working with a fuel containing 1300 vppm H₂S. At these conditions, the great majority of the sulphur fed into the system was released in the gas outlet of the FR as SO₂, affecting to the quality of the CO₂ produced. Formation of copper sulphide, Cu₂S, and the subsequent reactivity loss was only detected working at low values of ? ≤ 1.5, although this fact did not produce any agglomeration problem in the fluidized beds. In addition, the oxygen carrier was fully regenerated in a H₂S-free environment. It can be concluded that Cu-based oxygen carriers are adequate materials to be used in a CLC process using fuels containing H₂S although quality of the CO₂ produced is affected.     

Oxy-fuel coal combustion—A review of the current state-of-the-art

Carbon dioxide emissions will continue being a major environmental concern due to the fact that coal will remain a major fossil-fuel energy resource for the next few decades. To meet future targets for the reduction of greenhouse gas (GHG) emissions, capture and storage of CO₂ is required. Carbon capture and storage technologies that are currently the focus of research centres and industry include: pre-combustion capture, post-combustion capture, and oxy-fuel combustion. This review deals with the oxy-fuel coal combustion process, primarily focusing on pulverised coal (PC) combustion, and its related research and development topics. In addition, research results related to oxy-fuel combustion in a circulating fluidised bed (CFB) will be briefly dealt with.During oxy-fuel combustion, a combination of oxygen, with a purity of more than 95 vol.%, and recycled flue gas (RFG) referred to as oxidant is used for combusting the fuel producing a gas consisting of mainly CO₂ and water vapour, which after purification and compression, is ready for storage. The high oxygen demand is supplied by a cryogenic air separation process, which is the only commercially available mature technology. The separation of oxygen from air as well as the purification and liquefaction of the CO₂-enriched flue gas consumes significant auxiliary power. Therefore, the overall net efficiency is expected to be decreased by 8–12% points, corresponding to a 21–35% increase in fuel consumption. Alternatively, ion transport membranes (ITMs) are proposed for oxygen separation, which might be more energy efficient. However, since ITMs are far away from becoming a mature technology, it is widely expected that cryogenic air separation will be the selected technology in the near future. Oxygen combustion is associated with higher temperatures compared with conventional air combustion. Both fuel properties as well as limitations of steam and metal temperatures of the various heat exchanger sections of the boiler require a moderation of the temperatures in the combustion zone and in the heat-transfer sections. This moderation in temperature is accomplished by means of recycled flue gas. The interdependencies between the fuel properties, the amount and temperature of the recycled flue gas, and the resulting oxygen concentration in the combustion atmosphere are reviewed.The different gas atmosphere resulting from oxy-fuel combustion gives rise to various questions related to firing, in particular, with respect to the combustion mechanism, pollutant reduction, the risk of corrosion, and the properties of the fly ash or its resulting deposits. In this review, detailed nitrogen and sulphur chemistry was investigated in a laboratory-scale facility under oxy-fuel combustion conditions. Oxidant staging succeeded in reducing NO formation with effectiveness comparable to that typically observed in conventional air combustion. With regard to sulphur, a considerable increase in the SO₂ concentration was measured, as expected. However, the H₂S concentration in the combustion atmosphere in the near-flame zone increased as well. Further results were obtained in a pilot-scale test facility, whereby acid dew points were measured and deposition probes were exposed to the combustion environment. Slagging, fouling and corrosion issues have so far been addressed via short-term exposure and require further investigation.Modelling of PC combustion processes by computational fluid dynamics (CFD) has become state-of-the-art for conventional air combustion. Nevertheless, the application of these models for oxy-fuel combustion conditions needs adaptation since the combustion chemistry and radiative heat transfer is altered due to the different combustion gas atmosphere.CFB technology can be considered mature for conventional air combustion. In addition to its inherent advantages like good environmental performance and fuel flexibility, it offers the possibility of additional heat exchanger arrangements in the solid recirculation system, i.e. the ability to control combustion temperatures despite relatively low flue gas recycle ratios even when combusting in the presence of high oxygen concentrations.     

Effect of oxygenated liquid additives on the urea based SNCR process

An experimental investigation was performed to study the effect of oxygenated liquid additives, H₂O₂, C₂H₅OH, C₂H₄(OH)₂ and C₃H₅(OH)₃ on NO_x removal from flue gases by the selective non-catalytic reduction (SNCR) process using urea as a reducing agent. Experiments were performed with a 150 kW pilot scale reactor in which a simulated flue gas was generated by the combustion of methane operating with 6% excess oxygen in flue gases. The desired levels of initial NO_x (500 ppm) were achieved by doping the fuel gas with ammonia. Experiments were performed throughout the temperature range of interest, i.e. from 800 to 1200 °C for the investigation of the effects of the process additives on the performance of aqueous urea DeNO_x. With H₂O₂ addition a downward shift of 150 °C in the peak reduction temperature from 1130 to 980 °C was observed during the experimentation, however, the peak reduction efficiency was reduced from 81 to 63% when no additive was used. The gradual addition of C₂H₅OH up to a molar ratio of 2.0 further impairs the peak NO_x reduction efficiency by reducing it to 50% but this is accompanied by a downward shift of 180 °C in the peak reduction temperature. Further exploration using C₂H₄(OH)₂ suggested that a 50% reduction could be attained for all the temperatures higher than 940 °C. The use of C₃H₅(OH)₃ as a secondary additive has a significant effect on the peak reduction efficiency that decreased to 40% the reductions were achievable at a much lower temperature of 800 °C showing a downward shift of 330 °C.     

160 h of chemical-looping combustion in a 10 kW reactor system with a NiO-based oxygen carrier

Chemical-looping combustion, CLC, is a technology with inherent separation of the greenhouse gas CO₂. The technique uses an oxygen carrier made up of particulate metal oxide to transfer oxygen from combustion air to fuel. In this work, an oxygen carrier consisting of 60% NiO and 40% NiAl₂O₄ was used in a 10 kW CLC reactor system for 160 h of operation with fuel. The first 3 h of fuel operation excepted, the test series was accomplished with the same batch of oxygen carrier particles. The fuel used in the experiments was natural gas, and a fuel conversion to CO₂ of approximately 99% was accomplished. Combustion conditions were very stable during the test period, except for the operation at sub-stoichiometric conditions. It was shown that the methane fraction in the fuel reactor exit gas was dependent upon the rate of solids circulation, with higher circulation leading to more unconverted methane. The carbon monoxide fraction was found to follow the thermodynamical equilibrium for all investigated fuel reactor temperatures, 660–950 °C. Thermal analysis of the fuel reactor at stable conditions enabled calculation of the particle circulation which was found to be approximately 4 kg/s, MW. The loss of fines, i.e. the amount of elutriated oxygen carrier particles with diameter <45 μm, decreased during the entire test period. After 160 h of operation the fractional loss of fines was 0.00022 h⁻¹, corresponding to a particle life time of 4500 h.     

Drying of granulated wood ash by flue gas from saw dust and natural gas combustion

At the district heating plant of Kalmar, Sweden an on-line unit for production of granulated wood ash for nutrient recycling on forest soils is being applied. Currently, the granules are dried by hot air from an oil-fired burner. The objective of this work was to investigate how drying by flue gas affects the hardening of granules, or impacts their chemical composition and properties. Ninety-six granule samples were treated by flue gas from natural gas combustion in a laboratory pilot scale flue gas generator. CO₂, CO, O₂, C₃H₈ and NO concentrations were varied during the experiment. Additionally, some samples were treated by flue gas from combustion of sawdust at the heating plant in Kalmar. Drying by flue gases did not affect the chemical composition of granules, but minor effects were seen in their mineralogy. The carbonate content was slightly higher in granules treated with flue gas from natural gas combustion compared to the granules dried by hot air only, when measured by wet chemical methods. Results from XRD analysis imply that the calcite content is higher and the portlandite and arcanite content slightly less in granules treated with flue gas from sawdust combustion compared to the granules dried by hot air only. The results from this investigation showed no negative effects on ash granule composition or physical structure by the use of a flue as a drying medium.     

Effect of gas composition in Chemical-Looping Combustion with copper-based oxygen carriers: Fate of light hydrocarbons

Chemical-Looping Combustion (CLC) is an emerging technology for CO₂ capture because separation of this gas from the other flue gas components is inherent to the process and thus no energy is expended for the separation. Natural or refinery gas can be used as gaseous fuels and they may contain different amounts of light hydrocarbons. This paper presents the combustion results obtained with a Cu-based oxygen carrier using mixtures of CH₄ and light hydrocarbons (LHC) (C₂H₆ and C₃H₈) as fuel. The effect on combustion efficiency of the fuel reactor temperature, solid circulation flow rate and gas composition was studied in a continuous CLC plant (500 W_th). Full combustions were reached at 1073 and 1153 K working at oxygen to fuel ratios, ? higher than 1.5 and 1.2 respectively. Unburnt hydrocarbons were never detected at any experimental conditions at the fuel reactor outlet. Carbon formation can be avoided working at 1153 K or at ? values higher than 1.5 at 1073 K. After 30 h of continuous operation, the oxygen carrier exhibited an adequate behavior regarding attrition and agglomeration. It can be concluded that no special measures should be taken in a CLC process with Cu-based OC with respect to the presence of LHC in the fuel gas.     

The use of petroleum coke as fuel in a 10 kWth chemical-looping combustor

Tests were made in a 10 kW_th chemical-looping combustor with a petroleum coke as the solid fuel and the oxygen carrier ilmenite, an iron titanium oxide. The fuel reactor is fluidized by steam and the oxygen carrier reacts with the volatiles released as well as the gasification intermediates CO and H₂. A constant fuel flow corresponding to a thermal power of 5.8 kW was introduced into the fuel reactor and a total of 11 h of operation was reached. The effects of particle circulation and carbon stripper operation on solid fuel conversion, conversion of gas from the fuel reactor and CO₂ capture were investigated. The actual CO₂ capture ranged between 60% and 75% while the solid fuel conversion was in the range of 66–78%. The low values of solid fuel conversion reflect loss of char due to low efficiency of the fuel reactor cyclone. The incomplete conversion of the gas from the fuel reactor is expressed as oxygen demand. The oxygen demand corresponds to the fraction of oxygen lacking to achieve full gas conversion and was typically 25%, due to presence of CH₄, CO and H₂ from the fuel reactor. Typical ratios of CH₄, CO and H₂ over the total gaseous carbon from the fuel reactor are respectively 5, 10 and 25%. Low loss of non-combustible fines from the system indicates very low attrition of the oxygen carrier.     

Waste products from the steel industry with NiO as additive as oxygen carrier for chemical-looping combustion

Fe₂O₃-containing waste materials from the steel industry are proposed as oxygen carrier for chemical-looping combustion. Three such materials, red iron oxide, brown iron oxide and iron oxide scales, have been examined by oxidation and reduction experiments in a batch fluidized-bed reactor at temperatures between 800 and 950 °C. NiO-based particles have been used as additive, in order to examine if it is possible to utilize the catalytic properties of metallic Ni to facilitate decomposition of hydrocarbons into more reactive combustion intermediates such as CO and H₂. The experiments indicated modest reactivity between the waste materials and CH₄, which was used as reducing gas. Adding small amounts of NiO-based particles to the sample increased the yield of CO₂ in a standard experiment, typically by a factor of 1.5–3.5. The fraction of unconverted fuel typically was reduced by 70–90%. The conversion of CH₄ to CO₂ was 94% at best, corresponding to a combustion efficiency of 96%. This was achieved using a bed mass corresponding to 57 kg oxygen carrier per MW fuel, of which only 5 wt% was NiO-based synthetic particles. The different materials fared differently well during the experiments. Red iron oxide was fairly stable, while brown iron oxide was soft and subject to considerable erosion. Iron oxide scales experienced increased reactivity and porosity as function of the numbers of reduction cycles.     

Investigation of NiO/NiAl2O4 oxygen carriers for chemical-looping combustion produced by spray-drying

Chemical-looping combustion is a novel combustion technology with inherent separation of the greenhouse gas CO₂. The technology uses circulating oxygen carriers to transfer oxygen from the combustion air to the fuel. In this paper, oxygen carriers based on commercially available NiO and α-Al₂O₃ were prepared using the industrial spray-drying method, and compared with particles prepared by freeze-granulation. The materials were investigated under alternating oxidizing and reducing conditions in a laboratory fluidized bed, thus simulating the cyclic conditions of a chemical-looping combustion system. The particles produced by spray-drying displayed a remarkable similarity to the freeze-granulated oxygen carriers, with high reactivity when the bed was fluidized and similar physical properties when sintered at the same temperature. This is an important result as it shows that the scaling-up from a laboratory production method, i.e. freeze-granulation, to a commercial method suitable for large-scale production, i.e. spray-drying, did not involve any unexpected difficulties. A difference noticed between the spray-dried and freeze-granulated particles was the sphericity. Whereas the freeze-granulated particles showed near perfect sphericity, a large portion of the spray-dried particles had hollow interiors. Defluidization was most likely to occur for highly reduced particles, at low gas velocities. The apparent density and crushing strength of the oxygen carriers could be increased either by increasing the sintering temperature or by increasing the sintering time. However, the fuel conversion was fairly unchanged when the sintering temperature was increased but was clearly improved when the sintering time was increased.     

Purification of oxyfuel-derived CO2

Oxyfuel combustion in a pulverised fuel coal-fired power station produces a raw CO₂ product containing contaminants such as water vapour plus oxygen, nitrogen and argon derived from the excess oxygen for combustion, impurities in the oxygen used, and any air leakage into the system. There are also acid gases present, such as SO₃, SO₂, HCl and NO_x produced as byproducts of combustion. At GHGT8 (White and Allam, 2006) we presented reactions that gave a path-way for SO₂ to be removed as H₂SO₄ and NO and NO₂ to be removed as HNO₃. In this paper we present initial results from the OxyCoal-UK project in which these reactions are being studied experimentally to provide the important reaction kinetic information that is so far missing from the literature. This experimental work is being carried out at Imperial College London with synthetic flue gas and then using actual flue gas via a sidestream at Doosan Babcock's 160 kW coal-fired oxyfuel rig. The results produced support the theory that SO_x and NO_x components can be removed during compression of raw oxyfuel-derived CO₂ and therefore, for emissions control and CO₂ product purity, traditional FGD and deNO_x systems should not be required in an oxyfuel-fired coal power plant.     

Solid fuels in chemical-looping combustion

The feasibility of using a number of different solid fuels in chemical-looping combustion (CLC) has been investigated. A laboratory fluidized bed reactor system for solid fuel, simulating a chemical-looping combustion system by exposing the sample to alternating reducing and oxidizing conditions, was used. In each reducing phase 0.2 g of fuel in the size range 180–250 μm was added to the reactor containing 40 g oxygen carrier of size 125–180 μm. Two different oxygen carriers were tested, a synthetic particle of 60% active material of Fe₂O₃ and 40% MgAl₂O₄ and a particle consisting of the natural mineral ilmenite. Effect of steam content in the fluidizing gas of the reactor was investigated as well as effect of temperature. A number of experiments were also made to investigate the rate of conversion of the different fuels in a CLC system. A high dependency on steam content in the fluidizing gas as well as temperature was shown. The fraction of volatiles in the fuel was also found to be important. Furthermore the presence of an oxygen carrier was shown to enhance the conversion rate of the intermediate gasification reaction. At 950 °C and with 50% steam the time needed to achieve 95% conversion of fuel particles with a diameter of 0.125–0.18 mm ranged between 4 and 15 min depending on the fuel, while 80% conversion was reached within 2–10 min. In almost all cases the synthetic Fe₂O₃ particle with 40% MgAl₂O₄ and the mineral ilmenite showed similar results with the different fuels.     

A Novel Solar Thermal Cycle with Chemical Looping Combustion

In this paper, we have proposed a thermal cycle with the integration of chemical-looping combustion and solar thermal energy with the temperature of about 500-600°C. Chemical-looping combustion may be carried out in two successive reactions between a reduction of hydrocarbon fuel with metal oxides and a reduced metal with oxygen in the air. This loop of chemical reactions is substituted for conventional combustion of fuel. Methane as a fuel and nickel oxides as an oxygen carrier were employed in this cycle. Collected high-temperature solar thermal energy is provided for the endothermic reduction reaction. The feature of the proposed cycle is investigated through Energy-Utilization Diagram methodology. As a result, at the turbine inlet temperature of 1200°C, the exergy efficiency of the proposed cycle would be expected to be about 4 percentage points higher than that of a conventional gas turbine combined cycle. Compared to the previous study of chemical-looping combustion energy systems, the proposed cycle with the integration of green energy and traditional hydrocarbon fuels will offer the possibility of both greenhouse gas mitigation, with green energy, and a new approach to the efficient use of solar energy.     

Power generation with CO2 capture: Technology for CO2 purification

The goal of this paper is to find methodologies for removing a selection of impurities (H₂O, O₂, Ar, N₂, SO_x and NO_x) from CO₂ present in the flue gas of two oxy-combustion power plants fired with either natural gas (467 MW) or pulverized fuel (596 MW). The resulting purified stream, containing mainly CO₂, is assumed to be stored in an aquifer or utilized for enhanced oil recovery (EOR) purposes. Focus has been given to power cycle efficiency i.e.: work and heat requirements for the purification process, CO₂ purity and recovery factor (kg of CO₂ that is sent to storage per kg of CO₂ in the flue gas). Two different methodologies (here called Case I and Case II) for flue gas purification have been developed, both based on phase separation using simple flash units (Case I) or a distillation column (Case II). In both cases purified flue gas is liquefied and its pressure brought to 110 atm prior to storage.Case I: A simple flue gas separation takes place by means of two flash units integrated in the CO₂ compression process. Heat in the process is removed by evaporating the purified liquid CO₂ streams coming out from both flashes. Case I shows a good performance when dealing with flue gases with low concentration of impurities. CO₂ fraction after purification is over 96% with a CO₂ recovery factor of 96.2% for the NG-fired flue gas and 88.1% for the PF-fired flue gas. Impurities removal together with flue gas compression and liquefaction reduces power plant output of 4.8% for the NG-fired flue gas and 11.6% for the PF-fired flue gas. The total amount of work requirement per kg stored CO₂ is 453 kJ for the NG-fired flue gas and 586 kJ for the PF-fired flue gas.Case II: Impurities are removed from the flue gas in a distillation column. Two refrigeration loops (ethane and propane) have been used in order to partially liquefy the flue gas and for heat removal from a partial condenser. Case II can remove higher amounts of impurities than Case I. CO₂ purity prior to storage is over 99%; CO₂ recovery factor is somewhat lower than in Case I: 95.4% for the NG-fired flue gas and 86.9% for the PF-fired flue gas, reduction in the power plant output is similar to Case I.Due to the lower CO₂ recovery factor the total amount of work per kg stored CO₂ is somewhat higher for Case II: 457 kJ for the NG-fired flue gas and 603 kJ for the PF-fired flue gas.     

Characterization of a limestone in a batch fluidized bed reactor for sulfur retention under oxy-fuel operating conditions

CO₂ and SO₂ are some of the main polluting gases emitted into atmosphere in combustion processes using fossil fuel for energy production. The former is one of the major contributors to build-up the greenhouse effect implicated in global climate change and the latter produces acid rain. Oxy-fuel combustion is a technology, which consists in burning the fuel with a mix of pure O₂ and recirculated CO₂. With this technology the CO₂ concentration in the flue gas may be enriched up to 95%, becoming possible an easy CO₂ recovery. In addition, oxy-fuel combustion in fluidized beds allows in situ desulfurization of combustion gases by supplying calcium based sorbent.In this work, the effect of the principal operation variables affecting the sulfation reaction rate in fluidized bed reactors (temperature, CO₂ partial pressure, SO₂ concentration and particle size) under typical oxy-fuel combustion conditions have been analyzed in a batch fluidized bed reactor using a limestone as sorbent. It has been observed that sulfur retention can be carried out by direct sulfation of the CaCO₃ or by sulfation of the CaO (indirect sulfation) formed by CaCO₃ calcination. Direct sulfation and indirect sulfation operating conditions depended on the temperature and CO₂ partial pressure. The rate of direct sulfation rose with temperature and the rate of indirect sulfation for long reaction times decreased with temperature. An increase in the CO₂ partial pressure had a negative influence on the sulfation conversion reached by the limestone due to a higher temperature was needed to work in conditions of indirect sulfation. Thus, it is expected that the optimum temperature for sulfur retention in oxy-fuel combustion in fluidized bed reactors be about 925–950 °C. Sulfation reaction rate rose with decreasing sorbent particle size and increasing SO₂ concentration.     

Reduction of CaSO4 oxygen carrier with coal in chemical-looping combustion: Effects of temperature and gasification intermediate

Chemical-looping combustion (CLC) has been suggested as an energy efficient method for the capture of carbon dioxide from combustion. Thermodynamics and kinetics of CaSO₄ reduction with coal via gasification intermediate in a CLC process were discussed in the paper, with respect to the CO₂ generating efficiency, the environmental factor and the surface morphology of oxygen carrier. Tests on the combined process of coal gasification and CaSO₄ reduction with coal syngas were conducted in a batch fluidized bed reactor at different reaction temperatures and with different gasification intermediates. The products were characterized by gas chromatograph, gas analyzers and scanning electron microscope. And the results showed that an increase in the reaction temperature aggravated the SO₂ emission. The CO₂ generating efficiency also increased with the temperature, but it decreased when the temperature exceeded 950 °C due to the sintering of oxygen carrier particles. The use of CO₂ as gasification intermediate in the fuel reactor had a positive effect on the sintering-resistant of oxygen carrier particles. However, increasing the steam/CO₂ ratio in gasification intermediate evidently enhanced CO₂ generating efficiency and reduced SO₂ environmental impact.