西宁市环境空气中TSP和PM10来源解析研究

在西宁市7个采样点分别采集了环境空气中的总悬浮颗粒物(TSP)和可吸入颗粒物(PM10),用化学质量平衡(CMB)受体模型和二重源解析技术解析了TSP和PM10的来源。结果表明:扬尘、煤烟尘和土壤风沙尘是造成该市TSP和PM10污染的主要源类。扬尘是造成该市颗粒物污染的首要因素,控制城市扬尘污染是城市环境空气颗粒物达标的关键。     

Technological reviews of particulate matter and their source identification techniques

Particulate matter (PM) is one of the primary pollutants produced from mining operations. This paper summarizes the existing techniques used to identify sources of PM and their contribution to ambient air pollution. Human health studies indicate that there is an association between airborne PM and adverse health effects. Particularly in coal mining areas, the burning of coal and PM from machinery operations cause low air quality that is physically harmful. Thus, the sources of smoldering combustion, that are typical in coal mine burns, increase the risk to mine workers who are exposed to high concentrations of known toxicity associated with PM. Recent studies on the modeling of PM concentration profiles across various sources were reviewed for this paper.     

Distribution of lead in relation to size of airborne particulate matter in Islamabad, Pakistan

Airborne particulate matter (PM) collected from two sampling stations in Islamabad, Pakistan, was analyzed for lead content and size gradation. A high volume air sampler was used to trap particulates on glass fiber filters for 8-12 h on a daily basis. Lead was estimated using a nitric acid digestion based AAS method on 44 samples from station 1 and 61 samples from station 2. Particle size fractions were categorized as <2.5, 2.5-10, 10-100 and >100 microm. The correlation between lead concentration and particle size was investigated. The results from two stations indicated average airborne lead concentrations of 0.505 and 0.185 microg/m3. Enhanced levels of lead were measured at a maximum of 4.075 microg/m3 at station 1 and 4.000 microg/m3 at station 2. PM < 2.5 and PM > 100 were found to constitute the local atmosphere in comparable proportions. A comparison of the lead levels is made with the existing permissible levels of this element laid down by different international agencies.     

长沙市城区典型交通路口PM_(10)和PM_(2.5)污染特征研究

利用车载环境空气质量监测系统对长沙市城区典型交通路口的近地面空气质量进行了实时监测。结果表明,在监测时段(14∶00~20∶00)内,该监测点环境空气中PM10的小时质量浓度范围在0.097~0.222mg/m3之间,平均值0.163mg/m3;PM2.5的小时质量浓度范围在0.050~0.158mg/m3之间,平均值0.103mg/m3。PM2.5/PM10比值在48.1%~76.6%之间,平均值62.4%。PM10与PM2.5质量浓度在星期一相对较低,星期二有所升高,星期三至周末总体上保持基本稳定。在监测时段PM10与PM2.5小时质量浓度呈现先降后升的变化规律,即14∶00~15∶00,PM10与PM2.5质量浓度相对较高,16∶00左右降至最低,从17∶00开始逐渐升高,20∶00达到峰值。PM10和PM2.5的质量浓度变化与车流量和车速密切相关,温度、相对湿度和风速等气象因素对PM10和PM2.5质量浓度的变化影响也较显著。     

Predicting Particulate Matter (PM2.5) Concentrations in the Air of Shahr‐e Ray City,Iran, by Using an Artificial Neural Network

Particulate matter (PM), along with other air pollutants, pose serious hazards to human health. The Artificial Neural Network (ANN) is a branch of artificial intelligence that has an ability to make accurate predictions. In this article, the authors describe such methods and how historical data on air quality, moisture, wind velocity, and temperature in Shahr‐e Ray City, located at the southern tip of Tehran, was used to train an ANN to provide accurate predictions of PM concentrations. The availability of such predictions can offer significant assistance to those who are working to reduce air pollution.     

Assessment and management of air quality for an opencast coal mining area

A study for the assessment and management of the air quality was carried out at Lakhanpur area of Ib Valley Coalfield in Orissa state in India. The 24-h average concentrations of total suspended particulate (TSP) matter, respirable particulate matter (PM10), sulphur dioxide (SO2) and oxides of nitrogen (NOx) were monitored during 1 year period. Samplings were done at a regular interval through out the year at 13 monitoring stations in the residential areas and four monitoring stations in the mining/industrial areas. The 24-hr average TSP and PM10 concentrations ranged from 338.8 to 799.8 microg m(-3) and 102.5-425.6 microg m(-3) for industrial area, and 72.3-497.1 microg m(-3) and 40.8-171.9 microg m(-3) for residential area, respectively. During the study period 24-hr and annual average TSP and PM10 concentrations exceeded the respective standards set in the national ambient air quality standard (NAAQS) protocol at most residential and industrial areas. However, 24-hr and annual average concentrations of SO2 and NOx were well within the prescribed limit of NAAQS both in the residential and industrial areas. The annual and 24-hr average concentrations varied from 23.3 to 36.8 microg m(-3) and 16.0-55.2 microg m(-3) for SO2 and 23.9-41.9 microg m(-3) and 19.0-58.1 microg m(-3) for NOx, respectively. The temporal variations of TSP and PM10 fitted polynomial trend with an average correlation coefficient (R2) of 0.77 (+/-0.17) for TSP and 0.85 (+/-0.10) for PM10. On average the PM10 in the ambient air of the mining area constituted 31.94 (+/-1.76)% of the TSP. The linear regression correlation coefficient (R2) between TSP with PM10 and NOx with SO2 was 0.86 (+/-0.12) and 0.57 (+/-0.20), respectively. Maximal concentrations of TSP and PM10 occurred within the mining site based on the kriging technique. A management strategy is formulated for effective control of air pollution at source and other mitigative measures recommended including implementation of green belts around the sensitive areas where the concentration of air pollutants exceeded the standard limit.     

上海市青浦区PM10污染状况及其与气象要素的关系

利用2006-2010年上海市青浦区PM10和同期地面气象要素的监测资料,定量分析PM10的季节变化规律以及PM10与降雨量、大气湿度和风速之间的关系。分析结果表明:PM10浓度在夏季处于低值,冬季处于高值;5mm/d以上的降雨对PM10有显著的清除作用,且春夏季降雨的清除作用大于秋冬季节。PM10浓度与大气湿度基本呈负相关关系。风速在一定范围内有利于PM10的扩散但不至造成扬尘,春夏季节的适宜风速是1.5～3.5m/s,冬季的适宜风速是1.5～2.5m/s。     

南充市城市空气质量变化及达标分析

为了掌握南充市近年来城市空气质量变化及其达标情况,对南充市城区2008～2012年SO2、NO2和PM10的质量浓度数据进行统计分析,并计算各个站点的空气污染指数和空气质量指数。结果表明,3种污染物浓度值都有明显的下降趋势,S02浓度在0．002～0．052mg／m^3之间变化;N02浓度值从0．042mg／m^3下降到0．029mg／m^3;PM10浓度在0．060～0．063mg／m^3之间波动。南充市空气质量冬季较差,夏季较好。在5个监测点中,炼油厂空气质量最差,优良率为92．9％（85．1％）;高坪空气质量最好,优良率为99．1％（98．3％）。相关性分析表明,南充市空气污染源主要是工业燃煤和机动车尾气。     

Laboratory evaluation of dust-control effectiveness of pen surface treatments for cattle feedlots

Emission of particulate matter (PM) is one of the major air quality concerns for large beef cattle feedlots. Effective treatments on the uncompacted soil and manure mixture of the pen surface may help in reducing PM emission from feedlots. A laboratory apparatus was developed for measuring dust-emission potential of cattle feedlot surfaces as affected by pen surface treatments. The apparatus was equipped with a simulated pen surface, four mock cattle hooves, and samplers for PM with equivalent aerodynamic diam. ≤ 10 μm (PM(10)). The simulated pen surface had a layer of dry, loose feedlot manure with a compacted soil layer underneath. Mock hooves were moved horizontally on the manure layer to simulate horizontal action of cattle hooves on the pen surface. High-volume PM samplers were used to collect emitted dust. Effects of hoof speed, depth of penetration, and surface treatments with independent candidate materials (i.e., sawdust, wheat straw, hay, rubber mulch, and surface water application) on PM(10) emission potential of the manure layer were investigated. Our laboratory study showed PM(10) emission potential increased with increasing depth of penetration and hoof speed. Of the surface treatments evaluated, application of water (6.4 mm) and hay (723 g m(-2)) exhibited the greatest percentage reduction in PM(10) emission potential (69 and 77%, respectively) compared with the untreated manure layer. This study indicated application of hay or other mulch materials on the pen surface might be good alternative methods to control dust emission from cattle feedlots.     

The impact of urban growth on regional air quality surrounding the Langat River Basin, Malaysia

Studies of air quality were carried out in the towns of Kajang, Nilai and Banting in the Langat River Basin, southern region of Kuala Lumpur to determine the status and trend of air quality. The determination of air quality was based on several parameters such as suspended solids with diameters less than 10???m (PM₁₀) and gaseous pollutants of sulphur dioxide (SO₂), nitrogen dioxide (NO₂), ozone (O₃), and carbon monoxide (CO). Primary concentration data of air pollutants were compiled through fieldwork studies and combined with secondary data obtained from the regular monitoring data as collected by Alam Sekitar Malaysia Sdn. Bhd. (ASMA) on behalf of Malaysian Department of Environment (DOE) at their stations in Kajang and Nilai. Results showed that the average concentrations of PM₁₀, SO₂, NO₂, O_3, and CO at all sampling stations were still below the permissible values recommended by the Malaysian DOE. The level of gaseous pollutants of NO₂, O_3, and CO was recorded at statistically higher levels (p?<?0.05) than values recorded at the control station at Pangsun Recreational Area. These pollutants were suspected to have originated mainly from exhaust systems of motor vehicles. Data for the years 1996 to 2006 as obtained from ASMA showed long-term air quality trends of increasing O₃ and NO₂ concentrations in Kajang whilst concentrations of PM₁₀ recorded at both Kajang and Nilai stations were mostly expected coming from transboundary sources especially biomass burning and the development activities around the study areas.     

Air quality impact assessment of multiple open pit coal mines in northern Colombia

The coal mining region in northern Colombia is one of the largest open pit mining regions of the world. In 2009, there were 8 mining companies in operation with an approximate coal production of ～70 Mtons/year. Since 2007, the Colombian air quality monitoring network has reported readings that exceed the daily and annual air quality standards for total suspended particulate (TSP) matter and particles with an equivalent aerodynamic diameter smaller than 10 μm (PM??) in nearby villages. This paper describes work carried out in order to establish an appropriate clean air program for this region, based on the Colombian national environmental authority requirement for modeling of TSP and PM(10) dispersion. A TSP and PM?? emission inventory was initially developed, and topographic and meteorological information for the region was collected and analyzed. Using this information, the dispersion of TSP was modeled in ISC3 and AERMOD using meteorological data collected by 3 local stations during 2008 and 2009. The results obtained were compared to actual values measured by the air quality monitoring network. High correlation coefficients (>0.73) were obtained, indicating that the models accurately described the main factors affecting particle dispersion in the region. The model was then used to forecast concentrations of particulate matter for 2010. Based on results from the model, areas within the modeling region were identified as highly, fairly, moderately and marginally polluted according to local regulations. Additionally, the contribution particulate matter to the pollution at each village was estimated. Using these predicted values, the Colombian environmental authority imposed new decontamination measures on the mining companies operating in the region. These measures included the relocation of three villages financed by the mine companies based on forecasted pollution levels.     

Benchmarking compliance performance: A new petroleum industry report

Environmental Information Services, Inc. (EIS) publishes detailed reports and offers custom research related to the full spectrum of environmental issues facing corporations. In this new article, EIS reports on the compliance performance of the largest companies in the petroleum industry focusing on five key environmental concerns: toxic waste management, air pollution, water pollution, spills, and Superfund. It is important to note that the following article does not contain normalized data and graphs which would adjust findings to various size features (e.g., worldwide revenues per company). This as well as detailed environmental policy and program data on each company can be obtained from EIS. EIS reports help companies of all sizes benchmark their environmental performance and quality improvement efforts.     

我国大气细颗粒物污染防治目标和控制措施研究

我国面临着严重的细颗粒物(PM2.5)污染问题,PM2.5对人体健康、能见度、气候变化、生态系统等均产生了不良影响。本文旨在提出我国PM2.5污染防治目标和控制措施,为从根本上改善空气质量提供科学依据。首先,本文提出了2020年和2030年我国PM2.5污染防治目标。其次,采用能源和污染排放技术模型,分情景预测了我国未来一次大气污染物排放量的变化趋势。基于情景预测结果和此前研究建立的一次污染物排放与PM2.5浓度间的非线性关系,确定了2020年—2030年与PM2.5浓度改善相适应的全国和重点区域大气污染物减排目标。最后,利用能源和污染排放技术模型,提出了实现大气污染物减排的技术措施和对策建议。研究表明,2030年全国二氧化硫、氮氧化物、一次PM2.5和挥发性有机物的排放量应分别比2012年至少削减51%、64%、53%和36%,氨排放量也要略有下降。对于污染严重的重点区域,必须采取更严格的控制力度。要实现上述减排,应加快能源结构调整,推进煤炭清洁高效集中可持续利用,建立"车-油-路"一体的移动源控制体系,并强化多源多污染物的末端控制。     

PM2.5及其工业源头控制技术

PM2.5对人体健康和空气质量有巨大的危害,环保部已修订相关法规和文件,将PM2.5纳入我国环境空气质量监测范围,采取有效手段控制PM2.5是我国一项重要的环保目标,在工业企业中采用最先进的表面过滤技术可从源头控制工业PM2.5的排放。     

Study of boron behaviour in two Spanish coal combustion power plants

A full-scale field study was carried out at two Spanish coal-fired power plants equipped with electrostatic precipitator (ESP) and wet flue gas desulfurisation (FGD) systems to investigate the distribution of boron in coals, solid by-products, wastewater streams and flue gases. The results were obtained from the simultaneous sampling of solid, liquid and gaseous streams and their subsequent analysis in two different laboratories for purposes of comparison. Although the final aim of this study was to evaluate the partitioning of boron in a (co-)combustion power plant, special attention was paid to the analytical procedure for boron determination. A sample preparation procedure was optimised for coal and combustion by-products to overcome some specific shortcomings of the currently used acid digestion methods. In addition boron mass balances and removal efficiencies in ESP and FGD devices were calculated. Mass balance closures between 83 and 149% were obtained. During coal combustion, 95% of the incoming boron was collected in the fly ashes. The use of petroleum coke as co-combustible produced a decrease in the removal efficiency of the ESP (87%). Nevertheless, more than 90% of the remaining gaseous boron was eliminated via the FGD in the wastewater discharged from the scrubber, thereby causing environmental problems.     

乌鲁木齐市地面风场特征及其对空气污染影响初探

利用2005—2006年乌鲁木齐辖区9个地面自动气象站逐日逐时风速和风向监测数据,初步分析了乌鲁木齐市地面风场的主要特征;通过对2006—01—12乌鲁木齐市区连续多日出现重污染时段地面风场的分析,得出地面风场对重度空气污染的影响。     

Elemental composition of total dry particulate matter deposited in the selected industrial areas within Lagos state

The total particulate matter (PM) deposited within 17 selected industrial areas in Lagos state during the dry season (December 2015 to January 2016) was studied. Deposition gauges measuring 0.2 meters (m) in diameter by 0.15 m in depth were placed at the sampling locations for a period of one month to collect the total deposited PM. The PM was then characterized using energy‐dispersive X‐ray florescence (EDXRF). The sources of the heavy metals were evaluated using enrichment factor (EF) analysis. Factor analysis (FA) was then used to determine the correlations between the identified heavy metals. Twenty‐three elements—sodium (Na), silicon (Si), phosphorous (P), sulfur (S), chlorine (Cl), potassium (K), calcium (Ca), titanium (Ti), vanadium (V), chromium (Cr), manganese (Mn), iron (Fe), nickel (Ni), copper (Cu), zinc (Zn), germanium (Ge), arsenic (As), strontium (Sr), zirconium (Zr), lead (Pb), tungsten (W), polonium (Po), and actinium (Ac)—were characterized in the PM collected at the sampling sites. The iron elemental ratio ranged from 0.0003 to 3.8848. The EF ranged from 0.0015 to 1697.47, including at the control location. The FA, using principal component analysis techniques, revealed seven factor loadings with 90.03% cumulative, which suggests that the sources are anthropogenic, such as from industrial activities, vehicular emissions, and the combustion of fuel.     

Spatial variations in selected metal contents and particle size distribution in an urban and rural atmosphere of Islamabad, Pakistan

Spatial variations in total suspended particulate matter (TSP) were investigated for distribution of metals and particle size fractions in the urban and rural atmosphere of Islamabad, Pakistan. The metals Na, K, Fe, Mn, Pb, Cd, Cr, Zn, Ni and Co, and the particle fractions <2.5, 2.5-10, 10-100 and >100 microm were included in the study. TSP samples were trapped on glass fibre filters using high volume samplers and quantification of metals was done using Atomic Absorption Spectrometry employing HNO(3) based wet digestion. At the urban site, Na was dominant at 2.384 microg/m(3) followed by K, Fe and Zn with 0.778, 0.667 and 0.567 microg/m(3) as mean concentrations, respectively. The metal levels for the rural site ranged from 0.002 microg/m(3) for Cd to 1.077 microg/m(3) for Na. However, compared with the urban site, mean Pb concentration showed an almost two-fold enhancement, i.e., 0.163 Vs. 0.327 microg/m(3). Metals and particle size source identification was done using Principal Component Analysis and Cluster Analysis. Five sources were traced out for the urban site: industrial, soil, automobile emissions, metallurgical industries and excavation activities. For the rural site, four sources were recorded: agricultural, automotive emissions, excavation activities and metallurgical units. Collectively, for both the sites, PM(10-100) emerged as a major contributor to TSP, followed by PM(2.5-10), PM(<2.5) and PM(>100) in that order. The metals showed in general positive relationship with fine particulate fractions (PM(2.5-10), PM(<2.5)), and negative correlation with coarse fractions (PM(10-100), PM(>100)). Comparison with the corresponding data from various Asian sites revealed that the levels of Na, K, Fe, Mn, Co and Ni for the present study were lower than those reported for grossly polluted cities of the world.     

Load Estimation Method Using Distributions with Covariates: A Comparison with Commonly Used Estimation Methods

Load estimates obtained using an approach based on statistical distributions with parameters expressed as a function of covariates (e.g., streamflow) (distribution with covariates hereafter called DC method) were compared to four load estimation methods: (1) flow‐weighted mean concentration; (2) integral regression; (3) segmented regression (the last two with Ferguson's correction factor); and (4) hydrograph separation methods. A total of 25 datasets (from 19 stations) of daily concentrations of total dissolved solids, nutrients, or suspended particulate matter were used. The selected stations represented a wide range of hydrological conditions. Annual flux errors were determined by randomly generating 50 monthly sample series from daily series. Annual and interannual biases and dispersions were evaluated and compared. The impact of sampling frequency was investigated through the generation of bimonthly and weekly surveys. Interannual uncertainty analysis showed that the performance of the DC method was comparable with those of the other methods, except for stations showing high hydrological variability. In this case, the DC method performed better, with annual biases lower than those characterizing the other methods. Results show that the DC method generated the smallest pollutant load errors when considering a monthly sampling frequency for rivers showing high variability in hydrological conditions and contaminant concentrations.     

Analyzing the cost effectiveness of Santiago, Chile's policy of using urban forests to improve air quality

Santiago, Chile has the distinction of having among the worst urban air pollution problems in Latin America. As part of an atmospheric pollution reduction plan, the Santiago Regional Metropolitan government defined an environmental policy goal of using urban forests to remove particulate matter less than 10 microm (PM(10)) in the Gran Santiago area. We used cost effectiveness, or the process of establishing costs and selecting least cost alternatives for obtaining a defined policy goal of PM(10) removal, to analyze this policy goal. For this study, we quantified PM(10) removal by Santiago's urban forests based on socioeconomic strata and using field and real-time pollution and climate data via a dry deposition urban forest effects model. Municipal urban forest management costs were estimated using management cost surveys and Chilean Ministry of Planning and Cooperation documents. Results indicate that managing municipal urban forests (trees, shrubs, and grass whose management is under the jurisdiction of Santiago's 36 municipalities) to remove PM(10) was a cost-effective policy for abating PM(10) based on criteria set by the World Bank. In addition, we compared the cost effectiveness of managing municipal urban forests and street trees to other control policies (e.g. alternative fuels) to abate PM(10) in Santiago and determined that municipal urban forest management efficiency was similar to these other air quality improvement measures.