Pd/CZ/Al2O3催化剂的制备、表征与三效催化性能

以共浸渍法制得的氧化铝负载铈锆固溶体为载体,并浸渍贵金属Pd得到了Pd/CZ/Al2O3催化剂.实验结果表明,该催化剂在老化前后都表现出良好的三效催化活性,新鲜样品Pd/CZ/Al2O3活性与Pd/CZ相当,老化后样品前者优于后者.结合XRD,BET,TPR等表征手段,讨论了Pd/CZ/Al2O3的催化活性特别是高温老化后活性与其组成结构之间的内在关系,揭示了其老化后仍具有较高活性的主要原因在于保持了Pd与CZ/Al2O3复合载体之间的强相互作用(SMSI).     

Pd/Ce0.5Zr0.5O2三效催化剂负载方法

分别采用沉积沉淀、直接混合和传统的浸渍法制备1% Pd/Ce_0.5Zr_0.5O₂ 催化剂, 研究了Pd负载方法对催化剂活性影响.运用H₂-TPR和原位漫反射红外(DRIFTS)研究了Pd-铈锆载体间的相互作用及Pd/Ce_0.5Zr_0.5O₂催化剂上的三效反应机理.结果表明沉积沉淀法制备的Pd/Ce_0.5Zr_0.5O₂催化剂(Pd-DP)表现出最强的Pd-载体作用及最优活性,原位红外实验发现Pd-DP上存在与传统的浸渍法制备的Pd-IMP催化剂不同的NO催化还原途径,推测Pd-载体间相互作用引起NO还原机理差异,进而导致活性差异.     

富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究

考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂上丙烯选择性还原NO_x的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO₂/Al₂O₃催化剂相比,溶胶-凝胶法制备的5%SnO₂/Al₂O₃催化剂受水蒸汽的抑制作用较弱,并且在水和SO₂共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NO_x转化率的提高.     

Al2O3为载体的催化剂净化贫燃汽车尾气研究

在富氧条件下,考察了C₃H₆和C₂H₅OH在Ag/Al₂O₃、In/Al₂O₃、Sn/Al₂O₃、Co/Al₂O₃、Pt/Al₂O₃和Ag/Al₂O₃+Pt/Al₂O₃组合催化剂上选择性还原NO的性能.结果表明,Ag/Al₂O₃具有最高的NO还原活性.在负载型过渡金属氧化物催化剂上,会生成显著量的CO,其HC和CO氧化转化温度也远远高于Pt/Al₂O₃催化剂.串联组合Ag/Al₂O₃+Pt/Al₂O₃催化剂可显著拓宽活性温度范围,促进HC和CO氧化,降低N₂O和CH₃CHO生成量.     

Al2O3催化臭氧化处理邻苯二甲酸二甲酯

'Al₂O₃催化剂对邻苯二甲酸二甲酯(DMP)溶液臭氧化过程的影响结果表明:Al₂O₃可以显著提高臭氧氧化的效果,反应120min后,TOC的去除率从单独臭氧氧化的23.9%提高到55.1%.实验中还考察了制备条件对Al₂O₃催化剂活性的影响并确定了反应的最佳工艺条件.在实验考察的范围内:焙烧温度600℃,Al₂O₃粒径为0.5～1.0mm时催化活性最高;最佳反应工艺条件为:催化剂投加量20g/L,混和气体流速200mL/min,反应温度15℃.通过单独臭氧氧化,单独臭氧氧化后再进行催化剂吸附,催化臭氧化的对比实验证明了Al₂O₃催化剂对体系TOC的去除主要是基于催化作用.     

掺杂La或Si对Ag/Al2O3催化剂热稳定性和脱NO活性的影响

利用 BET比表面测定和 X-射线衍射技术考察了掺杂 La或 Si的 Ag/Al₂O₃催化剂的热稳定性 ,并研究了富氧条件下 ,丙烯在这些催化剂上选择性还原 NO的活性 .结果表明 ,掺杂 La或 Si能抑制 Al₂O₃相变 ,使 γ-Al₂O₃完全转化为 α-Al₂O₃的温度升至 1100℃以上 .相应地 ,延缓催化剂比表面下降 ,从活性角度来看 ,当焙烧温度为 1100℃时 ,与掺杂 La或 Si相比 ,不掺杂 La或 Si的 Ag/Al₂O₃催化剂活性要低得多 ;当焙烧温度低于 1000℃时 ,掺杂少量 La(2 % La₂O₃)对 Ag/Al₂O₃催化剂活性影响不大 ,但是 ,掺杂 Si(2%或 8% SiO₂)或较高含量 La(8% La₂O₃)会导致催化剂活性降低 .综合考虑热稳定性和富氧条件下的 NO还原活性 ,认为掺杂较低含量 La(2% La₂O₃)的 Ag/Al₂O₃催化剂性能最佳 .     

MnO2/Al2O3催化剂-微气泡臭氧体系催化降解喹啉及其机理

制备了纳米MnO₂,并以Al₂O₃为载体制备了掺杂型MnO₂/Al₂O₃颗粒催化剂.催化剂焙烧温度和时间分别为500℃和4 h、MnO₂质量分数为8%时,催化剂具有最高的臭氧催化氧化活性.SEM分析表明,纳米MnO₂均匀分布于Al₂O₃载体表面.MnO₂/Al₂O₃催化剂的比表面积（BET）为183.22 m²·g^-1,平均孔容为0.27 cm³·g^-1,平均孔径为4.87 nm.建立了MnO₂/Al₂O₃催化剂-微气泡臭氧催化反应体系,研究了该体系对喹啉的降解去除效果及其机理.臭氧微气泡的平均粒径为61.7 μm.微气泡臭氧投量为30 mg·L^-1时,反应60 min后喹啉去除率能达到95%以上;反应20 min后,MnO₂/Al₂O₃催化剂-微气泡臭氧体系对实际煤化工废水二级出水的TOC去除率可达到55%以上.以叔丁醇作为分子探针,证明了羟基自由基（·OH）氧化作用在臭氧微气泡催化氧化体系中对喹啉的降解起到主导作用.     

以堇青石蜂窝陶瓷为载体的新型钒氧化物脱氮催化剂研究

以TiO₂/Al₂O₃/堇青石蜂窝陶瓷为载体,以V₂O₅-MoO₃-WO₃为活性组分,用于氨法选择性催化还原烟气中NO的新型催化剂,并对该催化剂的活性性能和微观结构进行了评价和表征.同时,将该催化剂的活性性能与其它几种活性组分相同但载体、制备方法、结构不同的催化剂进行了对比.对比结果表明,该新型催化剂能取得最好的选择性催化还原氮氧化物催化性能BET、FT IR、XPS表征实验结果表明,其高催化活性得益于大比表面积及大孔体积,而TiO₂/Al₂O₃/堇青石蜂窝陶瓷载体及其制备方法对获得好的催化剂构型起了至关重要的作用.     

CuxCe1-xO2/γ-Al2O3催化剂催化燃烧甲苯性能的研究

以γ-Al₂O₃ 为载体,以复合氧化物Cu_xCe_1-xO₂为活性组分,其中,x=0.1,0.2,0.4,0.6,0.8,通过浸渍法制备了一系列Cu_xCe_1-xO₂/γ-Al₂O₃催化剂.在固定床反应器中评价了催化剂对甲苯的催化活性,通过XRD、SEM对催化剂进行表征,并运用ICP-MS分析并计算Cu、Ce的摩尔比以及活性组分的负载量.结果表明,在Cu_xCe_1-xO₂/γ-Al₂O₃催化剂中Cu、Ce摩尔比的实际值与理论值相近,活性组分的负载量在19%以上,而且对甲苯都有较好的低温催化活性,其中当x=0.2时,即Cu_0.2Ce_0.8O₂/γ-Al₂O₃催化剂对甲苯的催化活性最高,其中T₁₀=160 ℃,T₉₀=265 ℃;当甲苯的进口浓度在700~3000 mg·m^-3时,进口浓度对Cu_0.2Ce_0.8O₂/γ-Al₂O₃催化剂的催化活性影响较小,且经过连续80 h的稳定性操作后转化率仍然保持在90%以上.     

Effect of pretreatment on Pd/Al2O3 catalyst for catalytic oxidation of o-xylene at low temperature

The effect of pretreatment on Pd/Al₂O₃ catalysts for the catalytic oxidation of o-xylene at low temperature was studied by changing the pretreatment and testing conditions. The fresh and pretreated Pd/Al₂O₃ catalysts were characterized by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results showed that the pretreatment dramatically changed the Pd/PdO ratio and then significantly affected the Pd/Al₂O₃ activity; while the pretreatment had not much influence on Pd particle size. The Pd/Al₂O₃ pre-reduced at 300℃/400℃, which has fully reduced Pd species, showed the highest activity; while the fresh Pd/Al₂O₃, which has fully oxidized Pd species, presented the worst performance, indicating the Pd chemical state plays an important role in the catalytic activity for the o-xylene oxidation. It is concluded that metallic Pd is the active species on the Pd/Al₂O₃ catalyst for the catalytic oxidation of o-xylene at low temperature.     

Effects of Ce on catalytic combustion of methane over Pd-Pt/Al2O3 catalyst

Activity and stability of 1%Pd-0.2%Pt/Al₂O₃ and 1%Pd-0.2%Pt/0.6%Ce/Al₂O₃ catalysts prepared by impregnation method for catalytic combustion of methane in air were investigated. The catalysts before and after reaction were characterized by BET, CO chemisorption, XRD and XPS techniques. Results showed that the presence of Ce significantly increased the activity and thermal stability of the Pd-Pt/Al₂O₃ catalyst towards methane combustion, which could be attributed to more highly-dispersed active PdO particles over the Pd-Pt/Ce/Al₂O₃ catalyst surface as well as the retarded sintering of PdO and the maintained oxidized state of surface Pd during the combustion process in the presence of Ce.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

Preparation and characterization of Pd/Fe bimetallic nanoparticles immobilized on Al2O3/PVDF membrane: Parameter optimization and dechlorination of dichloroacetic acid

Using a liquid–solid phase inversion method, a hybrid matrix poly(vinylidene fluoride)(PVDF) membrane was prepared with alumina(Al2O3) nanoparticle addition. Pd/Fe nanoparticles(NPs) were successfully immobilized on the Al2O3/PVDF membrane, which was characterized by Scanning Electron Microscopy(SEM) and Transmission Electron Microscopy(TEM). The micrographs showed that the Pd/Fe NPs were dispersed homogeneously. Several important experimental parameters were optimized, including the mechanical properties, contact angle and surface area of Al2O3/PVDF composite membranes with different Al2O3 contents. At the same time, the ferrous ion concentration and the effect of hydrophilization were studied. The results showed that the modified Al2O3/PVDF membrane functioned well as a support. The Al2O3/PVDF membrane with immobilized Pd/Fe NPs exhibited high efficiency in terms of dichloroacetic acid(DCAA) dechlorination. Additionally, a reaction pathway for DCAA dechlorination by Pd/Fe NPs immobilized on the Al2O3/PVDF membrane system was proposed.     

Pd/CeZr/TiO2/Al2O3蜂窝状金属丝网催化剂选择催化还原NOX

采用溶胶-凝胶法和浸渍法制备了Pd/CeZr/TiO2Al2O3蜂窝状金属丝网催化剂,并将其应用于在富氧条件下以丙烯选择催化还原NOx的研究.利用扫描电镜(SEM)分析了钛酸四丁酯的含量以及涂敷次数对TiO2涂层的影响,系统地考察了Pd含量、氧气浓度和空速对蜂窝状金属丝网催化剂催化性能的影响.实验结果表明,采用钛酸四丁酯的含量为20.0%的溶胶,涂敷2次,可以在金属丝网载体上氧化铝涂层表面获得均匀、无皲裂的TiO2涂层;Pd含量在0.23%～1.06%的范围内, NOx的转化率随Pd含量的增加而减小, Pd含量为0.23%时, NOx表现最高的NOx转化率;反应气体中氧气浓度从1.5%增加到6.0%, NOx的转化率随氧气浓度的增加而增大,当氧气浓度高于6.0%, NOx的转化率则随氧气浓度的增加而迅速减小; NOx的转化率随着空速的增加而降低,在高温条件下空速对转化率的影响要大于在低温条件下.     

Effect of CeO2 and Al2O3 on the activity of Pd/Co_3O_4/cordierite catalyst in the three-way catalysis reactions (CO/NO/CnHm)

The present article studies the effect of CeO₂ and Al₂O₃ on the activity of Pd/Co₃O₄/cordierite catalyst in conversion of NO, CO, C_nH_m. The catalysts were characterized by temperature programmed reduction with hydrogen, X-ray diffraction, X-ray photoelectron spectroscopy and transmission electron microscopy. It is shown that the effect of CeO₂ on the properties of Pd/Co₃O₄/cordierite catalyst depends on preparation method. The catalyst obtained by co-deposition of cerium and cobalt oxides has higher activity in CO oxidation (CO + O₂ and CO + NO) and total hexane oxidation (C₆H₁₄ + O₂). Such phenomenon is probably caused by more than stoichiometric amount of formed oxygen vacancies, an increase in both mobility of surface oxygen and dispersity of components in the catalytic composition. It is demonstrated that CeO₂ addition promotes the SO₂ resistance of Pd/Co₃O₄/cordierite. The second support decreases the activity of Pd/Co₃O₄/cordierite catalyst in the reactions of CO and C₆H₁₄ with oxygen because of CoAl₂O₄ formation.     

Pd/Al2O3粒子电极电催化还原BrO3-的研究

针对常规方法难以去除水中Br_3~-的问题,采用浸渍煅烧法制备了负载型纳米Pd/Al_2O_3粒子电极,研究了该电极电催化还原Br O-3的效果.催化剂的结构表征表明该反应实现了Pd纳米晶的均匀负载,纳米Pd/Al_2O_3具有较高的电催化活性和较低的能耗,其最佳反应条件为3%Pd负载量,0.9 m A·cm-2电流密度和1 g·L催化剂投量,酸性条件可促进Br O-3的直接或间接还原.ESR检测证实了Pd的负载增强了反应体系活性物种[H]的生成,进而促进了Br O-3的间接电催化还原.     

CuO对贵金属/CeO2/Al2O3催化剂的作用

制备含少量贵金属Ｐｔ、Ｐｄ的不同Ｃｕ和Ｃｅ摩尔含量比（０：１０,１：９,２：８）的催化剂,实验条件十加入ＣｕＯ可以提高Ｐｔ催化剂的二效活性;加入Ｃｕ：Ｃｅ＝２：８的ＣｕＯ降低了Ｐｄ催化剂的顾效性能,然而Ｃｕ：Ｃｅ＝１：９时可以改善Ｐｄ催化剂的三效催化性能。通过结构分析,认为ＣｕＯ的存在可以提高ｄ催化剂的比表面积,ＰｄＯ的分散度。