雾化电晕净化烹调油烟技术

对雾化电晕放电极雾化过程、荷电液滴的捕集原理、自清洗作用进行探讨,在相同电压下雾化负电晕放电电流高于干式负电晕放电电流,极间大量荷电液滴具有很高的荷质比,并高速向极板驱进,对烟尘具有静电凝并和动力凝并除尘作用,具有高效净化油烟、自清洗极板的功能,此项净化烹调油烟的新技术,优于传统油烟净化技术,具有很好的应用价值和前景.     

雾化电晕净化烹调油烟技术

对雾化电晕放电极雾化过程、荷电液滴的捕集原理、自清洗作用进行探讨,在相同电压下雾化负电晕放电电流高于干式负电晕放电电流,极间大量荷电液滴具有很高的荷质比,并高速向极板驱进,对烟尘具有静电凝并和动力凝并除尘作用,具有高效净化油烟、自清洗极板的功能,此项净化烹调油烟的新技术,优于传统油烟净化技术,具有很好的应用价值和前景。     

高炉除尘灰细微颗粒物单/双预荷电强化滤袋过滤特性

传统袋式除尘器对于细微颗粒物的捕集效率不甚理想,在袋式除尘器入口前增加预荷电装置是一种切实可行的强化其过滤特性的技术手段。设计搭建线板式直流高压预荷电器,研究了不同正/负匹配电压及风速对于双极预荷电高炉除尘灰电凝并行为的影响规律,对比分析了滤袋对未荷电、单极负荷电以及双极荷电高炉除尘灰细微颗粒物(PM_2.5)的捕集效率与压差特性,得到了不同预荷电方式高炉除尘灰细微颗粒物在滤袋表面沉积的微观形貌结构。结果表明：随着过滤风速(1.5～0.5 m·s^-1及匹配负电压(-16～-12 kV)的降低,双极荷电颗粒物凝并效率提高;高炉除尘灰细微颗粒物单/双预荷电均能提高滤袋的过滤效率;对于粒径<0.5μm颗粒,双极预荷电技术对滤袋捕集效率的强化效果好于单极预荷电技术;对粒径为0.5～2.5μm颗粒,单极预荷电技术的强化效果超过了双极预荷电技术;颗粒物单/双预荷电技术还使得滤袋阻力增量值及其增长速率值降低,且单极预荷电技术对于阻力降低效果更为明显。本研究可为利用单/双预荷电技术提升传统袋式除尘器对高炉除尘灰中细微颗粒物的捕集脱除特性提供参考。     

去除亚微米颗粒的带电除尘器

大气污染物中的颗粒物的控制,经过人们长时间的努力,从技术的角度来讲,已基本解决。亚微米颗粒,由于其质量小,单单依靠一次控制过程很难解决。为了控制这种对人体健康危害很大的亚微米颗粒,利用冷凝,凝聚和荷电可以使颗粒物被此团聚的原理,设计了一些新型的除尘装置,即所谓二次控制。例如,利用冷凝和凝聚作用设计的除尘装置,在我     

印染废水和抛煤机锅炉烟尘综合治理

印染废水和抛煤机锅炉烟尘是两大污染源.印染废水中较难处理的一是脱色,二是COD的去除.抛煤机锅炉排放烟尘浓度过高,经各种干式除尘器和多个湿式除尘器净化,仍不能达到国家规定的排放标准.本工艺运用烟尘的表面吸附、接触凝聚、气水冲击和气液接触等多种原理,实现了利用锅炉烟尘处理印染废水和利用印染废水净化锅炉烟尘的综合治理目的,经过二年多的工业化运行表明,这种工艺是合理的.也是可行的.     

电凝聚技术在水处理中的研究进展

电凝聚作为一项电化学水处理技术,应用领域日益广泛,技术日益成熟。因此,系统地描述了电凝聚技术的电极反应、影响参数与能耗情况,侧重阐述了电凝聚在水处理中的最新应用和研究,最后概括了电凝聚技术的优势和不足。     

粉尘双极荷电对滤料电荷累积抑制作用

为解决单极性电袋复合除尘器因滤料电荷积累导致清灰难和反电晕烧袋问题,将线管式双极荷电器引用到电袋复合除尘技术中。基于电晕电流最大化方法进行荷电器的电极结构优化实验。当电晕极采用RS芒刺线、管电极采用不锈钢管时,荷电器的较优极配为管电极直径25 mm、管间距120 mm、电晕线到管电极的异极距80 mm。在荷电器和导电纤维滤料组装成的静电增强纤维过滤装置上,分别进行粉尘单极荷电和非对称双极荷电情况下滤料电荷积累量的对比实验。实验粉尘采用中位径3.5μm硅微粉。在过滤风速为0.17 m·s~(-1)、平均电场强度2.5~3.0 kV·cm~(-1)的实验条件下,当气流含尘浓度为700 mg·m~(-3)时,双极荷电粉尘在滤料上累积电荷产生的电流值比单极荷电粉尘滤料上累积电荷产生的电流值低约25%,表明双极荷电对滤袋电荷积累有明显的抑制作用。     

电凝聚在废水处理中的研究进展

电凝聚法是一种有效的电化学废水处理方法,因此对目前电凝聚技术在废水处理中的研究与应用进行了综述,阐述了电凝聚技术的机理,介绍了电凝聚处理的影响因素。     

偶极荷电静电凝并除尘器收尘机理及性能研究

提出一种高效去除微细颗粒物的偶极荷电静电凝并除尘装置,其主要由凝并区和收尘区组成.对其凝并收尘机理进行了分析,并对收尘性能进行了实验研究.结果表明,偶极荷电静电凝并系数高于库仑凝并系数;偶极荷电静电凝并除尘器中颗粒的凝并效果好,且在相同的条件下,其对微细颗粒物的除尘效率明显高于普通静电除尘器.     

水环境中腐殖酸的荷电特性与聚集特性

通过腐殖酸的Zeta电位和粒径的变化规律研究,探讨化学条件对腐殖酸的荷电状态和聚集状态的影响。结果表明,腐殖酸具有自我凝聚的特性;在pH较低和溶液离子强度较高时,腐殖酸胶粒的Zeta电位绝对值减小而聚合度增大,从而使腐殖酸胶粒聚集而凝聚;随腐殖酸浓度增大,腐殖酸胶粒的Zeta电位绝对值增大,腐殖酸胶粒的缩聚程度降低而使粒径减小。     

Collection of Fly Ash with High Electrical Resistivity in a Pilot Plant Electrostatic Precipitator Preceded by the EPA/SoRI Precharger

It is well known that dust with high electrical resistivity is difficult to collect in electrostatic precipitators (ESP). The difficulty is primarily due to poor particle charging. This poor particle charging is not because particles having high electrical resistivity are intrinsically difficult to charge, but because back corona (which results from deposition of material on the collection electrode) produces a bipolar ion field. When ions of both positive and negative polarity are present in the charging region, the competing effects of the two, plus low values of electric field, produce low electrical charge on particles.     

Calculation of the Charging Rate of Fine Particles by Unipolar Ions

Theories of particle charging based on boundary value solutions to the diffysional equation may not be applicable to electrostatic precipitators where the ion density is rarely more than an order of magnitude greafer than the particle concentration. A new charging equation, based on kinetic theory, is presented which evaluates the charging rate in terms of the probability of collisions between the flust particles and ions. In the presence of an external electric field, the surface of the particle is divided into three charging regions, and separate charging rates are calculated for each region. The total charging rate is the sum of these three individual rates. For large particles and high electric fields, this theory predicts essentially the same charging rate as the classical field charging equation of Rohmann and Pauthenier. For low electric fields, the theory reduces to White’s diffusional charging equation. Agreement is within 25% of Hewitt’s experimental results over the entire range of variables where data are available. For practical charging times, agreement is within 15%.     

Variation of the mixing state of Saharan dust particles with atmospheric transport

Mineral dust is an important aerosol species in the Earth’s atmosphere and has a major source within North Africa, of which the Sahara forms the major part. Aerosol Time of Flight Mass Spectrometry (ATOFMS) is first used to determine the mixing state of dust particles collected from the land surface in the Saharan region, showing low abundance of species such as nitrate and sulphate internally mixed with the dust mineral matrix. These data are then compared with the ATOFMS single particle mass spectra of Saharan dust particles detected in the marine atmosphere in the vicinity of the Cape Verde islands, which are further compared with those from particles with longer atmospheric residence sampled at a coastal station at Mace Head, Ireland. Saharan dust particles collected near the Cape Verde Islands showed increased internally mixed nitrate but no sulphate, whilst Saharan dust particles collected on the coast of Ireland showed a very high degree of internally mixed secondary species including nitrate, sulphate and methanesulphonate. This uptake of secondary species will change the pH and hygroscopic properties of the aerosol dust and thus can influence the budgets of other reactive gases, as well as influencing the radiative properties of the particles and the availability of metals for dissolution.     

Role of Chinese wind-blown dust in enhancing environmental pollution in Metropolitan Seoul

A suite of rock magnetic experiments and intensive microscopic observations were carried out on Asian dust deposits in Seoul, Korea, collected on 19 and 23 March 2002, 9 April 2002 and 12 April 2003. Desert-sand and loess from the dust source regions in China were also analyzed as a comparison. Asian dust showed a higher magnetic concentration than the source region samples, indicating a significant influx of magnetic particles into Asian dust had occurred during its transportation. Electron microscopy identified carbon-bearing iron-oxides as the added material. These iron-oxides were likely to have been produced by anthropogenic pollution (fossil fuel combustion) while the wind-blown dusts passing across the industrial areas of eastern China and western Korea. Such wind-paths were confirmed by a simulation of the air-mass trajectories. The magnetic technique appears to be useful for determining the anthropogenic pollution of Asian dust.     

Pollution of the roadside environment by dust particles from road surface repairs

The purpose of the study is to investigate the practical aspects of environmental pollution near motorways by dust particles formed during repair works and to identify specific ways to improve the overall environmental situation near highways and reduce the level of pollution during road maintenance. The leading approach is a systematic analysis of the problems of environmental pollution by dust emissions in general. The study results reflect the entire volume of research efforts made to determine the optimal composition of the concrete mixture for road repairs, which allows reducing the emission of dust particles into the surrounding roadside environment and improves the environmental situation on the roadside.

     

The Efficiency of Electrostatic Precipitators Under Conditions of Corona Quenching

The suppression of corona by particle space-charge is of considerable importance in electrostatic precipitators dealing with medium to high concentrations of particulates. However, the effect of the dust concentration on collection efficiency has found no direct answer in the literature. In addition to the expected reduction in corona current due to low mobility dust particles, the presence of these charged particles has two other main effects: 1. The electric field in the vicinity of the discharge electrode is weakened and hence the concentration of ions originating in the ionization zone and forming the charging current is decreased. 2. The resulting space-charge build-up causes an increase in the field strength adjacent to the collecting surface of the precipitator. The importance of each of these effects on the collection efficiency will be dependent on the relative decrease in particle charge as compared to the increase in the collection field. Experiments were carried out under both positive and negative corona with aerosol concentrations having specific surfaces in the range 0 to 44 m²/m³. These results showed: 1. For low values of corona current densities, as the specific surface area increases, the efficiency decreases. In this cqse, the charge per particle decreases as the particle concentration increases and becomes far below the normal charge attainable. Here the increase in the collection field is more than counteracted by the jarge reduction in particle charge. 2. For higher values of initial corona current densities, as the particle specific surface area increases, the efficiency either increases slightly or stays constant, in spite of major reductions in the measured corona current. In this case there should also be a reduction in the charge per particle with the increase in particle concentration, however, this is apparently offset by the increase in the collection field strength. Analysis of the results, coupled with an interpretation of existing theories, indicates that a major parameter that must be considered is the ratio of the initial corona current density and the specific surface of the particles.     

Variability of atmospheric dust loading over the central Tibetan Plateau based on ice core glaciochemistry

A Mt. Geladaindong (GL) ice core was recovered from the central Tibetan Plateau (TP) spanning the period 1940–2005 AD. High-resolution major ion (Na⁺, K⁺, Ca²⁺, Mg²⁺, Cl^?, SO₄^2?, NO₃^?) time-series are used to investigate variations in atmospheric dust loading through time. The crustal source ions vary seasonally with peaks in dust concentrations occurring during the winter and spring which are consistent with atmospheric dust observations at local meteorological stations. However, both similarities and dissimilarities are displayed between the decadal variation of atmospheric dust in the GL core and dust observation records from meteorological stations, which can be attributed to local environmental effects at the stations. This paper compares the 1980s and 1970s as case periods for low and high atmospheric dust loading, respectively, two periods reflecting shifts in spring atmospheric circulation (a weakening of zonal and meridional winds) from the 1970s (a period of enhanced dust aerosol transportation to central TP) to the 1980s (a period of diminished dust aerosol transportation to central TP), especially a significant decrease of meridional wind speeds in the 1980s. GL ice core dust proxies (Ca²⁺ and K⁺) are correlated with Total Ozone Mapping Spectrometer (TOMS) Aerosol Index (AI) data in spring over the TP and in the northwestern China (especially for K⁺). Thus variability of crustal ions in central TP ice core provides a proxy for reconstructing a history of atmospheric dust loading not only on the TP, but also in northwestern China.     

Nitrate and sulfate in individual Asian dust-storm particles in Beijing,China in Spring of 1995 and 1996

Energy dispersive X-ray analysis of elements and reagent thin-film test of particulate nitrate and sulfate were carried out to examine individual dust particles collected in Beijing during five dust-storm events occurring in spring of 1995 and 1996. Dominant particles were electron-opaque and had irregular shapes during the dust-storm periods, and their size was frequently in the range larger than 1 μm (diameter). Besides, some mineral particles that showed regular cubic shapes were found in the range from 0.1 to 2 μm. Their X-ray spectrums indicated calcium was abundant and little or no other elements with atomic number larger than 11 existed in such particles. They were supposed to be emitted initially from construction sites, and then formed through crystallization in the atmosphere. Their most possible composition was CaO or Ca(OH)₂. It was estimated that 93% of the collected electron-opaque particles are dust particles and the cubic particles in term of number frequency. On reagent films, few dust particles reacted apparently with barium chloride suggesting there was no water-soluble sulfate on the surface of dust particles although X-ray spectrums of about 14.6% of dust particles showed peaks of sulfur. The frequency of nitrate-containing particles in dust particles was 10.8%, which was much smaller than that in mineral particles collected in non-dust-storm periods. These results suggest that almost no sulfate is formed and nitrate is hardly formed on the surface of dust particles during their transport from source areas to Beijing.     

The Onset of Electrical Breakdown in Dust Layers: II. Effective Dielectric Constant and Local Field Enhancement

Part I of this work has shown that electrical breakdown in dust layers obeys Paschen's Law, but occurs at applied field values which appear too small to initiate the breakdown. In this paper we will show how an effective dielectric constant characterizing the dust layer can be determined from ac dielectric measurements and the theory of Debye. When combined with an expression for the enhanced local electric field in the void spaces between particles in the layer, field strengths which are large enough to initiate electrical breakdown in the layer are predicted at relatively low values of applied field. The effect of temperature and dust layer thickness on the onset of electrical breakdown within the dust layer can also be explained by the dependence of the effective dielectric constant on these parameters.     

Emission of respirable dust from stone quarrying,potential health effects,and its management

Mining of minerals exerts adverse pressure on different compartments of environment directly or indirectly. Air is the worst affected environmental matrix, and it can carry the harmful effect of pollutants generated from mining activity even to distant places. The present study was undertaken to estimate the emission of particulate matter (PM_2.5 and PM₁₀) from different activities undertaken in stone quarrying in Mahendragarh, Haryana. The results obtained from the present study indicated that drilling, blasting, crushing, and transport of mined material are chiefly responsible for the generation of dust. Whereas drilling, blasting, and loading were responsible for emission of higher fraction of PM₁₀, crushing and re-suspension of roadside dust from movement of vehicles resulted in generation of relatively higher fraction of finer dust (PM_2.5). Modelling the transport of dust over the Hybrid Single-Particle Lagrangian Integrated Trajectory model revealed that the emitted particle may move up to the distance of about 40 km within 4 h of emission under average meteorological conditions. Fourier transform infrared (FTIR) spectroscopy analysis of dust confirmed the presence of calcite and gypsum, thus confirming the source as mining. The study concluded that generation of PM_2.5-sized particles may impose serious respiratory health effects over the workers engaged in mining, crushing, and transportation of sandstone. Apart from it, population residing downwind of the mining area is particularly vulnerable to the pulmonary effects due to inhalation of dust.