酸活化赤泥催化臭氧氧化降解水中硝基苯的效能研究

以铝工业废物赤泥为原料,采用酸化的方法活化赤泥,提高其在多相催化臭氧氧化除污染体系中的催化活性,并对其催化臭氧除污染效能及机制进行探讨.研究发现,和赤泥原矿相比,酸化赤泥表现出十分显著的催化能力;酸化赤泥(RM6.0)催化臭氧氧化硝基苯的去除率随臭氧浓度的增加而增加;当臭氧浓度由0.4 mg.L-1增加至1.7 mg.L-1时,硝基苯的去除率由45%提高到92%.溶液pH对RM6.0催化体系利用臭氧能力的影响与其催化臭氧氧化降解NB的影响表现出一致的结果.初始pH变化所带来的RM6.0催化活性的变化,主要是由于体系中氢氧根浓度的变化,导致臭氧分解形成羟基自由基所致;过高pH值导致的羟基自由基的猝灭显促使RM6.0催化臭氧氧化NB活性的降低.通过RM6.0对臭氧的利用能力及羟基自由基抑制实验结果发现,RM6.0催化臭氧降解NB的主要作用机制是催化剂表面吸附臭氧,实现臭氧在催化剂表面的富集,进而实现对NB有机污染物的氧化降解.在这个过程中羟基自由基是存在的,主要是在臭氧与硝基苯在界面氧化过程中分解而成,并进一步氧化NB.     

水合氧化铁催化臭氧氧化去除水中痕量硝基苯

以实验室制备的水合氧化铁(IHO)为催化剂,研究了其催化臭氧氧化去除水中痕量难氧化有机物--硝基苯的效能,通过研究叔丁醇对催化反应的影响以及氧化物催化性能之间的对比,间接推断了催化反应的机理.探讨了催化剂投量、水质因素和催化剂重复使用对催化氧化硝基苯的影响.发现IHO对臭氧氧化水中的痕量硝基苯有明显的催化活性,在本实验条件下,以蒸馏水为本底,反应20min时催化氧化硝基苯的去除率比单独臭氧氧化高出44.8%.这种催化作用遵循羟基自由基的途径,氧化物羟基含量多对催化反应有利.本实验条件下催化剂投量最佳为100mg/L,水溶液的pH值接近氧化物零电荷pH值(pH_zpc)时催化作用最明显,水中重碳酸根浓度为2.38mmol/L时催化作用受到显著抑制.催化剂重复使用了5次,其催化活性基本没有变化,没有发现铁离子溶出.     

MgO催化臭氧氧化降解苯酚机理研究

对氧化镁(MgO)催化臭氧氧化降解苯酚的机理进行了探讨,并验证其与现有的3种催化臭氧氧化机理的吻合性.同时,研究了羟基自由基(·OH)抑制剂对苯酚去除效果的影响,·OH的产生量,以及臭氧在该体系中的存在位置及苯酚在该体系中的作用.结果表明,O_3和MgO/O_3两种反应体系中都存在·OH,MgO/O_3体系中的·OH是O_3体系中的2.14倍.O_3和MgO/O_3体系中的·OH与臭氧浓度的比值分别为1.47×10~(-9)和3.15×10~(-9).苯酚在MgO催化臭氧氧化体系中起到了促进臭氧吸附在MgO表面的作用,臭氧吸附到MgO表面后,分解产生·OH,一部分释放在溶液中降解苯酚,一部分则留在其表面增加表面羟基密度.     

铈掺杂Ru/Al2O3催化臭氧氧化降解邻苯二甲酸二甲酯

考察了铈(Ce)的掺杂对Ru/Al2O3催化臭氧氧化邻苯二甲酸二甲酯(DMP)溶液过程的影响.结果表明,Ce的掺杂可以显著提高臭氧氧化的效果,反应100min后,TOC的去除率可以由原催化剂的61.3%提高到75.1%,而单独臭氧氧化仅有14.0%.在实验范围内,Ru和Ce同时浸渍催化效果较好,且活性组分的溶出最少,Ce的最佳掺杂量为1.0%.通过催化剂吸附试验、单独臭氧氧化试验、Ce的均相催化试验及Ru-Se/Al2O3催化剂的非均相催化实验,证明Ru-Ce/Al2O3催化剂对DMP溶液臭氧氧化体系TOC的去除率达到50%,这是基于Ru-Ce/A12O3催化剂的非均相催化作用.     

金属氧化物催化臭氧氧化机理研究进展

催化臭氧氧化技术是目前水处理研究的热点,其中金属氧化物是催化臭氧化最常用的催化剂之一,因价格便宜、具有良好的催化性能备受关注。由于催化反应机理复杂,臭氧分子在催化剂表面的分解产物多样,同一种催化剂的催化臭氧化机理存在争议。文章讨论了金属氧化物催化臭氧化中发现的多种机理,主要包括羟基自由基机理、超氧自由基机理、表面络合配位机理和表面氧原子机理;催化剂表面性质影响臭氧分子的分解方式,分别探讨了表面羟基和表面氧空位存在时对催化反应机理的影响,发现表面羟基和氧空位的存在可以促进臭氧分子进一步解离,在诱导臭氧分子分解中起关键作用;讨论了金属氧化物催化臭氧化机理研究的发展趋势,为实际应用提供参考。     

Mn-Ce/C-Al2O3催化剂制备及其处理含苯酚废水研究

将碳材料与Al_2O_3作为催化剂载体的优势互补,将碳包裹在Al_2O_3外侧,开发了新型MnCe/C-Al_2O_3催化剂,探究了制备参数对模拟含苯酚焦化废水中有机物降解的影响,考察了催化剂的稳定性。结果表明:经6%葡萄糖溶液碳负载后,催化剂比表面积增加26.36%;锰的负载提供Lewis酸点并促进了臭氧活化为·OH过程,铈提升了锰的催化效果,在锰铈比为4∶1、450℃条件下烘焙4小时,催化剂对COD、TOC和UV_(254)的降解率可达85.52%、86.06%和90.96%;催化剂在10次降解实验中对COD的去除效果都较为稳定,均值为77.5%,Mn-Ce/C-Al_2O_3催化剂兼具良好的催化活性和稳定性。     

MnO2/Al2O3催化剂-微气泡臭氧体系催化降解喹啉及其机理

制备了纳米MnO₂,并以Al₂O₃为载体制备了掺杂型MnO₂/Al₂O₃颗粒催化剂.催化剂焙烧温度和时间分别为500℃和4 h、MnO₂质量分数为8%时,催化剂具有最高的臭氧催化氧化活性.SEM分析表明,纳米MnO₂均匀分布于Al₂O₃载体表面.MnO₂/Al₂O₃催化剂的比表面积（BET）为183.22 m²·g^-1,平均孔容为0.27 cm³·g^-1,平均孔径为4.87 nm.建立了MnO₂/Al₂O₃催化剂-微气泡臭氧催化反应体系,研究了该体系对喹啉的降解去除效果及其机理.臭氧微气泡的平均粒径为61.7 μm.微气泡臭氧投量为30 mg·L^-1时,反应60 min后喹啉去除率能达到95%以上;反应20 min后,MnO₂/Al₂O₃催化剂-微气泡臭氧体系对实际煤化工废水二级出水的TOC去除率可达到55%以上.以叔丁醇作为分子探针,证明了羟基自由基（·OH）氧化作用在臭氧微气泡催化氧化体系中对喹啉的降解起到主导作用.     

Fe/Mn-PAC催化剂的制备及其催化臭氧氧化降解活性艳蓝KN-R性能

为获得高效去除活性艳蓝的方法,采用浸渍煅烧法制备了Fe/Mn-PAC催化剂,对催化剂的表面形态和结构进行表征,研究了不同因素对KN-R降解效果的影响,以及催化剂的重复利用性和稳定性。结果表明：Fe/Mn-PAC催化剂表面粗糙,具有较多的微孔结构,催化剂表面的金属氧化物为致密的地衣状结构,有利于提升催化剂的催化性能。在催化剂投加量为400 mg/L,初始pH为7.5,Fe/Mn进料比为1∶1及负载量为4%时,Fe/Mn-PAC表现出最佳的催化KN-R降解的反应活性,45 min内KN-R去除率高达90%以上;经过5次回收利用,去除率仍可达到84.7%。研究结果证明了Fe/Mn-PAC催化剂具有优异的催化能力和出色的结构稳定性,为实现印染废水中活性艳蓝KN-R的有效去除提供了技术支持。     

Ru/AC催化臭氧氧化难生物降解有机物

研究了臭氧单独氧化和Ru/AC催化臭氧氧化DMP、酚类物质和消毒副产物前体物.结果表明,Ru/AC能显著提高臭氧氧化中有机物的矿化效果.在DMP降解中,反应100 min后TOC的去除率由单独臭氧氧化的28.84%提高到66.13%.在23种酚类物质降解中,反应60min后TOC的去除率由单独臭氧的9.57%~56.08%提高到41.81%~82.32%.相对于单独臭氧,Ru/AC催化臭氧氧化更能有效地降低水源水中消毒副产物的生成势,以卤乙酸生成势的降低最为明显,100 min后卤乙酸生成势由144.02μg/L降到58.50μg/L,低于美国环保局规定的限制浓度60μg/L.而使用单独臭氧处理并不能使卤乙酸生成势降到符合美国EPA的规定.比较了BAC、O3+BAC、O3/AC+BAC以及Ru/AC+O3+BAC工艺处理水源水的效果,TOC平均去除率分别为3.80%、20.14%、27.45%和48.30%;COD平均去除率分别为4.37%、27.22%、39.91%和50.00%;UV254去除率分别为8.16%、62.24%、67.03%和84.95%.Ru/AC+O3+BAC工艺相比其他工艺,更能有效地...     

TiO2/AC催化臭氧氧化处理水中的苯酚

研究了单独臭氧氧化及以活性炭(AC)和负载二氧化钛的活性碳(TiO2/AC)为催化剂催化臭氧氧化处理水中苯酚的效果。考察了AC、TiO2/AC对苯酚的吸附特性及三种方法对苯酚的转化率及矿化率效果及其臭氧利用效率,并对氧化过程进行了动力学分析。实验结果表明:AC、TiO2/AC对苯酚的吸附均较好地符合Freundlich方程;催化臭氧氧化转化苯酚的效果高于单独臭氧氧化;TiO2/AC作催化剂有利于苯酚的最终矿化,同时提高了臭氧的利用效率;3种氧化反应均较好的符合二级动力学方程,TiO2/AC催化臭氧氧化苯酚的二级动力学常数为0.0001L/(mg.min),高于单独臭氧氧化0.00004L/(mg.min)和AC催化臭氧氧化0.00006L/(mg.min)。     

Fe2O3@SCe多相芬顿催化剂的制备及其降解放热性能

为研究多相Fenton体系降解有机污水过程的放热规律,为污水处理的能源化利用提供技术支撑,本文以半焦（SCe）为载体,制备了Fe₂O₃@SCe新型复合材料,并对复合材料进行了BET、FTIR、XRD、SEM表征,研究了Fe₂O₃@SCe/H₂O₂多相Fenton体系处理邻苯二胺（OPD）模拟废水的降解性能和放热规律.结果表明,Fe₂O₃均匀负载于SCe颗粒表面,Fe₂O₃@SCe复合材料保留了改性SCe的多孔形态和强吸附性,在3.1~8.9的pH值范围内均表现出较高的催化活性;Fe₂O₃@SCe/H₂O₂多相Fenton体系在去离子水中自身分解和在邻苯二胺模拟废水的降解反应都释放了大量的热量,在[OPD]= 0.04mol/L;pH=7.8;T₀=30℃;[H₂O₂]=0.25mol/L;[Fe₂O₃@Sce]=533g/L;t=180min反应条件下的溶液温度升高数值为7.1℃,降解率为88.2%; H₂O₂的投加浓度是影响反应放热量的主要因素.     

Rapid degradation of dyes in water by magnetic Fe/Fe3O4/graphene composites

Magnetic Fe⁰/Fe₃O₄/graphene has been successfully synthesized by a one-step reduction method and investigated in rapid degradation of dyes in this work. The material was characterized by N₂ sorption–desorption, scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), vibrating-sample magnetometer (VSM) measurements and X-ray photoelectron spectroscopy (XPS). The results indicated that Fe⁰/Fe₃O₄/graphene had a layered structure with Fe crystals highly dispersed in the interlayers of graphene, which could enhance the mass transfer process between Fe⁰/Fe₃O₄/graphene and pollutants. Fe⁰/Fe₃O₄/graphene exhibited ferromagnetism and could be easily separated and re-dispersed for reuse in water. Typical dyes, such as Methyl Orange, Methylene Blue and Crystal Violet, could be decolorized by Fe⁰/Fe₃O₄/graphene rapidly. After 20 min, the decolorization efficiencies of methyl orange, methylene blue and crystal violet were 94.78%, 91.60% and 89.07%, respectively. The reaction mechanism of Fe⁰/Fe₃O₄/graphene with dyes mainly included adsorption and enhanced reduction by the composite. Thus, Fe⁰/Fe₃O₄/graphene prepared by the one-step reduction method has excellent performance in removal of dyes in water.     

MnFe2O4磁性纳米棒非均相Fenton催化降解水中四环素的研究

采用水热合成法成功制备出MnFe₂O₄磁性纳米棒(s-MnFe₂O₄),并考察了商品化的Fe₃O₄、MnFe₂O₄和合成的s-MnFe₂O₄纳米棒这3种磁性纳米颗粒作为非均相Fenton催化剂降解水中四环素抗生素的性能.同时,采用X射线衍射(XRD)、透射电镜(TEM)、N₂吸附-脱附、振动样品磁强计(VSM)及X射线光电子能谱(XPS)等技术对催化剂的理化性质进行了表征.非均相Fenton催化降解四环素的结果表明,s-MnFe₂O₄具有最高的催化活性,反应180 min,四环素的去除率可以达到87.6%,TOC的去除率达到47.5%.自由基捕获试验证实了羟基自由基(·OH)是非均相Fenton氧化过程中的主要活性物种.s-MnFe₂O₄磁性纳米棒的高催化活性归...     

纳米结构Fe3O4/Y2O3磁性颗粒的制备、表征及磷吸附行为研究

采用共沉淀法制备了一种新型铁钇氧化物(Fe3O4/Y2O3)磁性吸附剂,并对其表面特性及磷吸附行为进行了初步研究.扫描电镜(SEM)与X-射线衍射仪(XRD)表征结果表明,此吸附剂具有纳米结构,初级粒子平均粒径为15.2nm.振动样品磁强计(VSM)测得比饱和磁化强度为38.7emu·g-1,磁性较强,可方便地实现固液分离.吸附剂的等电点为6.8.磷吸附实验表明,25℃时,Langmuir吸附等温线可较好地拟合Fe3O4/Y2O3对溶液中磷的吸附(R2=0.989),最大吸附量(pH=5.0)为60.6mg·g-1(以P计);吸附速率较快,在120min内可完成吸附容量的80%以上,符合准二级动力学模型(R2=0.997);溶液pH对Fe3O4/Y2O3吸附磷的影响较为明显,离子强度则影响不大;共存阴离子对吸附影响的大小顺序为Cl-相似文献   

纳米四氧化三铁/过碳酸钠降解DDTs及降解产物

以滴滴涕(DDTs)为降解对象,采用基于纳米Fe_3O_4/过碳酸钠的新型非均相类芬顿试剂进行处理,考察了纳米Fe_3O_4投加量、过碳酸钠投加量和初始pH值对水中DDE、DDD、o,p′-DDT和p,p′-DDT4种DDTs去除率的影响.同时,采用响应面法进行多因素实验设计,利用二次多项式和逐步回归法拟合了DDTs降解率与实验条件之间的关系,并对实验条件进行了优化.结果表明,纳米Fe_3O_4和过碳酸钠单独处理对DDTs降解率的最大值均小于60%,两者联合处理可大幅度提高DDTs降解率,表明两者对于DDTs降解存在较好的协同作用,纳米Fe_3O_4/过碳酸钠体系在碱性条件下可以有效降解水样中的DDTs.在纳米Fe_3O_4投加量为8.0 g·L~(-1)、过碳酸钠投加量为1.5 g·L~(-1)、溶液初始pH值为11的条件下,DDE、DDD、o,p′-DDT和p,p′-DDT的降解率分别为95.5%、84.3%、96.8%和87.5%,与模型预测值接近.自由基猝灭实验结果表明,羟基自由基是降解过程中主要的活性物质.GC/MS检测结果表明,DDTs脱氯生成DDE和DDD,随后DDE和DDD进一步降解生成DDMU、o,p′-TDE、DDNU、DDMS及DBP等物质.     

Removal of tetracycline from aqueous solution by a Fe3O4 incorporated PAN electrospun nanofiber mat

Pollution of antibiotics, a type of emerging contaminant, has become an issue of concern, due to their overuse in human and veterinary application, persistence in environment and great potential risk to human and animal health even at trace level. In this work, a novel adsorbent, Fe₃O₄ incorporated polyacrylonitrile nanofiber mat (Fe-NFM), was successfully fabricated via electrospinning and solvothermal method, targeting to remove tetracycline (TC), a typical class of antibiotics, from aqueous solution. Field emission scanning electron microscopy and X-ray diffraction spectroscopy were used to characterize the surface morphology and crystal structure of the Fe-NFM, and demonstrated that Fe-NFM was composed of continuous, randomly distributed uniform nanofibers with surface coating of Fe₃O₄ nanoparticles. A series of adsorption experiments were carried out to evaluate the removal efficiency of TC by the Fe-NFM. The pseudo-second-order kinetics model fitted better with the experimental data. The highest adsorption capacity was observed at initial solution pH 4 while relative high adsorption performance was obtained from initial solution pH 4 to 10. The adsorption of TC on Fe-NFM was a combination effect of both electrostatic interaction and complexation between TC and Fe-NFM. Freundlich isotherm model could better describe the adsorption isotherm. The maximum adsorption capacity calculated from Langmuir isotherm model was 315.31 mg/g. Compared to conventional nanoparticle adsorbents which have difficulties in downstream separation, the novel nanofiber mat can be simply installed as a modular compartment and easily separated from the aqueous medium, promising its huge potential in drinking and wastewater treatment for micro-pollutant removal.     

Removal of tetracycline from aqueous solution by a Fe3O4 incorporated PAN electrospun nanofiber mat

Pollution of antibiotics, a type of emerging contaminant, has become an issue of concern, due to their overuse in human and veterinary application, persistence in environment and great potential risk to human and animal health even at trace level. In this work, a novel adsorbent, Fe₃O₄ incorporated polyacrylonitrile nanofiber mat (Fe-NFM), was successfully fabricated via electrospinning and solvothermal method, targeting to remove tetracycline (TC), a typical class of antibiotics, from aqueous solution. Field emission scanning electron microscopy and X-ray diffraction spectroscopy were used to characterize the surface morphology and crystal structure of the Fe-NFM, and demonstrated that Fe-NFM was composed of continuous, randomly distributed uniform nanofibers with surface coating of Fe₃O₄ nanoparticles. A series of adsorption experiments were carried out to evaluate the removal efficiency of TC by the Fe-NFM. The pseudo-second-order kinetics model fitted better with the experimental data. The highest adsorption capacity was observed at initial solution pH 4 while relative high adsorption performance was obtained from initial solution pH 4 to 10. The adsorption of TC on Fe-NFM was a combination effect of both electrostatic interaction and complexation between TC and Fe-NFM. Freundlich isotherm model could better describe the adsorption isotherm. The maximum adsorption capacity calculated from Langmuir isotherm model was 315.31 mg/g. Compared to conventional nanoparticle adsorbents which have difficulties in downstream separation, the novel nanofiber mat can be simply installed as a modular compartment and easily separated from the aqueous medium, promising its huge potential in drinking and wastewater treatment for micro-pollutant removal.     

Promoting catalytic ozonation of phenol over graphene through nitrogenation and Co3O4 compositing

Catalytic ozonation is progressively becoming an attractive technique for quick water purification but efficient and stable catalysts remains elusive. Here we solvothermally synthesized highly-dispersed Co₃O₄ nanocrystals over microscale nitrogen-doping graphene (NG) nanosheets and tested it as a synthetic catalyst in the ozonation of phenol in aqueous solutions. Transmission electron microscopy, powder X-ray diffraction, Fourier transform infrared spectra and X-ray photoelectron spectroscopy were used to determine its morphology, crystallinity, elemental composition and molecular bonds, respectively. The comparative experiments confirmed the highest catalytic activity and oxidation degree (AOSC) of Co₃O₄/NG among four nanocomposites (G, NG, Co₃O₄/G, and Co₃O₄/NG). Co₃O₄/NG also has exhibited the highest degradation rate: complete conversion of a near-saturated concentration of phenol (941.1 mg/L) was achieved within 30 min under ambient conditions with only a small dosage of Co₃O₄/NG (50 mg/L) and ozone (4 mg/L, flow rate: 0.5 L/min). It also resulted in 34.6% chemical oxygen demand (COD_Cr) and 24.2% total organic carbon (TOC) reduction. In this work, graphene nanosheets not only functioned as a support for Co₃O₄ nanocrystals but also functioned as a co-catalyst for the enhancement in phenol removal efficiency. The surface nitridation and Co₃O₄ modification treatment further improved the removal rate of the phenol pollutants and brought in the higher oxidation degree. Our finding may open new perspectives for pursuing exceptional activity for catalytic ozonation reaction.     

四氧化三铁/聚乙烯亚胺纳米颗粒的制备及除磷性能的研究

采用化学共沉淀法,以聚乙烯亚胺(PEI)为改性剂,制备了聚乙烯亚胺改性的纳米四氧化三铁复合材料(Fe3O4/PEI).Zeta电位、透射电镜和FTIR表征结果显示,PEI修饰提高了纳米Fe3O4在水中的分散性和稳定性,同时也增强了其表面正电荷,从而提高了Fe3O4对水中磷酸根的去除能力.在磷酸根初始浓度为50 mg·L~(-1),Fe3O4/PEI投加量为200 mg,p H=3,温度为25℃的条件下,Fe3O4/PEI对100 m L磷酸根的吸附去除率达到91%.吸附过程在3 h内达到平衡.吸附等温数据表明,该吸附过程符合Langmuir吸附等温方程,可决系数R2达到0.99,最大吸附量为29.88 mg·L~(-1).Fe3O4/PEI复合材料重复利用性好,在第5次吸附-解析后还能保持对磷酸根75%以上的吸附去除率.磷的解析效率随着p H增加而增加,在p H=13时,解析效率达到65%.