高效负载型光催化剂制备及其加铂修饰技术

通过光催化氧化五氯苯酚钠实验,结合对催化剂晶型结构、比表面积的表征分析,优化钛酸四丁酯水解制备TiO₂负载型催化剂并加铂修饰的制备条件:R值、烧结温度、粘合剂添加量、空心玻璃珠粒径大小及催化剂中铂含量,从而制备出高效、实用的负载加铂修饰型半导体光催化剂.实验结果表明,当R=10,温度为650℃烧结1h,TiO₂∶硅酸钠∶空心玻璃珠=10∶2.5∶20(W),铂在催化剂中的重量百分比为1.4%～1.6%,空心玻璃珠的粒径为0.5mm时,所制备的加铂修饰负载型催化剂催化活性、使用寿命和牢固度均比较理想.用该催化剂做光催化实验,当反应液初始五氯苯酚钠浓度为100mg/L、pH值为6.5,催化剂投加量为2g/L,通氧气量为1.6mL/s,光照强度为30kW/m²时,五氯苯酚钠2 h光催化氧化率达92.0%.     

钛酸四丁酯水解制备TiO_2半导体光催化剂研究

研究了钛酸四丁酯水解制备TiO2 粉末的两大影响因素R值 (R是水和钛酸四丁酯的摩尔比 )和烧结温度 .通过光催化氧化五氯苯酚钠实验 ,结合对催化剂晶型结构、比表面积的表征分析 ,综合评价所制备的催化剂 .实验结果表明 ,当R =10 0、烧结温度为 6 5 0℃、烧结时间为 1h ,钛酸四丁酯水解所制备的TiO2 半导体光催化剂催化活性和使用寿命均比较理想 .从晶型结构分析 ,当催化剂中锐钛矿和金红石按一定比例共存时 ,其催化活性较单一金红石或锐钛矿高 .实验认为锐钛矿与金红石的最佳比约为 2∶1     

负载型催化剂光催化氧化五氯苯酚钠的效果

研究以TiO₂ 为基本活性组分、空心玻璃珠为载体、硅酸钠为粘合剂的负载型催化剂的制备技术 .选取五氯苯酚钠 (PCP-Na)为处理对象 ,结合对催化剂比表面和晶型结构的表征 ,对制备的催化剂进行筛选评价 .实验结果表明 :在适当的条件下 (二氧化钛、空心玻璃珠、40%硅酸钠溶液重量比为 4∶20∶2,650℃下烧 3h)所制备的C3型催化剂不仅光催化活性高 ,且负载牢固 ,易与水分离 .对初始COD_Cr=400mg·L^-1,PCP-Na=10mg·L^-1的反应液 ,在光照强度为 30kW·m^-2下 2hCOD_Cr去除率大于 65% ,PCP-Na去除率大于 92%.试验进一步探讨C3型催化剂投加量、反应液初始浓度、供氧量对催化反应的影响 .     

V~(5+)/TiO_2-SiO_2-GF复合光催化剂制备及降解甲醛的研究

采用溶胶-凝胶法制备了纯TiO2、TiO2-SiO2、V5+/TiO2-SiO2光催化剂,并分别负载于玻璃纤维布上,利用X射线衍射(XRD)和比表面及孔隙度(BET)分析技术对样品进行了表征。以甲醛的降解率来评价复合光催化剂的光催化活性。结果表明:玻璃纤维布预处理方式、TiO2与SiO2的复合配比、V的掺杂量、煅烧温度对纳米TiO2的光催化活性有影响。V5+/TiO2-SiO2复合光催化剂比表面积为143.74 m2/g,晶粒粒径为16.9 nm。     

空心玻璃微球附载TiO2清除水面漂浮的油层

以空心玻璃微球为载体，采用浸涂法制备出ＴｉＯ２／ｂｅａｄｓ光催化剂．研究了利用ＴｉＯ２／ｂｅａｄｓ光催化剂降解水面漂浮的正十二烷及甲苯的可行性．结果表明，３７５Ｗ中压汞灯照射１２０ｍｉｎ，正十二烷的光催化去除率达９３．５％，光照８０ｍｉｎ时甲苯被完全光催化去除；通入空气有利于正二十烷及甲苯的光催化去除，外加微量的Ｈ２Ｏ２（５．０ｍｍｏｌ／Ｌ）可大大提高光催化去除率，向反应液中加入少量Ｎａ＋对正十二烷及甲苯的光催化去除率无明显的影响．     

低温燃烧合成纳米Ni掺杂TiO2光催化剂的表征及活性研究

采用低温燃烧合成法制备了Ni掺杂TiO₂光催化剂,通过紫外-可见漫反射光谱(UV-Vis DRS)、X射线粉末衍射(XRD)、激光散射、热重-差示扫描量热分析(TG-DSC)等方法对催化剂的光吸收特性、晶相组成、粒度分布、升温过程中化学变化等进行了表征,以亚甲基蓝为模型污染物考察了催化剂在可见光下的光催化活性.结果表明,相对P25而言,Ni掺杂TiO₂的光吸收带边红移,当Ni/Ti原子比为0.4时,催化剂的带隙宽度为2.3eV,对应的吸收带边为564nm;催化剂晶型以锐钛矿TiO₂为主,随Ni掺杂量增大,NiTiO₃比例升高;催化剂粒径主要分布在50～150nm之间,占总量的96.9%;升温过程中催化剂在445.2℃发生晶型转化,出现锐钛矿和NiTiO₃晶体.催化剂显示出较高的催化活性,在可见光作用150min后最高可使93.9%的亚甲基蓝分解,活性高于P25.     

Photocatalytic remediation of γ-hexachlorocyclohexane contaminated soils using TiO2 and montmorillonite composite photocatalyst

TiO2 and montmorillonite composite photocatalysts were prepared and applied in degrading γ-hexachlorocyclohexane （γ-HCH） in soils. After being spiked with γ-HCH, soil samples loaded with the composite photocatalysts were exposed to UV-light irradiation. The results indicated that the photocatalytic activities of the composite photocatalysts varied with the content of TiO2 in the order of 10%〈70%〈50% 〈30%, Moreover, the photocatalytic activity of the composite photocatalysts with TiO2 content 30% was higher than that of the pure P25 with the same mass of TiO2. The strong adsorption capacity of the composite photocatalysts and quantum size effect may contribute to its increased photocatalytic activities. In addition, effect of dosage of composite photocatalysts and soil pH on γ-HCH photodegradation was investigated. Pentachlorocyclohexene, trichlorocyclohexene, and dichlorobenzene were detected as photodegradation intermediates, which were gradually degraded with the photodegradation evolution.     

附载型复合光催化剂TiO2.Al2O3/beads降解有机磷农药

研究以四异丙醇钛［Ti(iso-OC₃H₇)4］、异丙醇铝为原料,以空心玻璃微球为载体,用溶胶-凝胶法制备可漂浮附载型复合光催化剂TiO₂.Al₂O₃/beads的过程。用该光催化剂降解有机磷农药,并与光催化剂DegussaP-25TiO2光活性进行比较。结果表明,附载型复合光催化剂活性显著提高,最高光活性为同样降解条件下,同样含量DegussaP-25TiO₂光活性的1.4倍,且TiO₂.Al₂O₃组分摩尔比存在最佳值。同时还研究了TiO₂.Al₂O₃/beads对有机磷农药的吸附性,并用XRD和TEM对附载型复合光催化剂进行表征。      

Photocatalytic remediation of γ-hexachlorocyclohexane contaminated soils using TiO2 and montmorillonite composite photocatalyst

TiO2 and montmorillonite composite photocatalysts were prepared and applied in degrading γ-hexachlorocyclohexane(γ-HCH)in soils.After being spiked with γ-HCH,soil samples loaded with the composite photocatalysts were exposed to UV-light irradiation.The results indicated that the photocatalytic activities of the composite photocatalysts varied with the content of TiO2 in the order of 10%＜70%＜50%＜30%.Moreover,the photocatalytic activity of the composite photocatalysts with TiO2 content 30% was higher than that of the pure P25 with the same mass of TiO2.The strong adsorption capacity of the composite photocatalysts and quantum size effect may contribute to its increased photocatalytic activities.In addition,effect of dosage of composite photocatalysts and soil pH on γ-HCH photodegradation was investigated. Pentachlorocyclohexene,trichlorocyclohexene,and dichlorobenzene were detected as photodegradation intermediates,which were gradually degraded with tlle phOtOdegradation evolution.     

Zr/TiO2纳米颗粒的制备及其光催化活性

以钛酸丁酯,乙醇为原料,用固相合成法制备了Zr/TiO2纳米颗粒,用XRD、TEM对其组成、颗粒大小、形貌进行了表征.通过对罗丹明B的降解反应,考察了Zr/TiO2的光催化活性.结果表明,Zr/TiO2为纳米颗粒,平均粒径为12.7 nm左右,且颗粒均匀;掺杂金属离子Zr提高了TiO2光催化效率,掺杂2.0%Zr的催化剂活性最高.Zr/TiO2的光催化反应,首先是反应物在Zr/TiO2表面发生吸附作用,然后进一步发生光催化降解.     

不同煅烧温度制备的Mn、N掺杂TiO2光催化性能研究

以MnSO4·H2O为锰源,尿素为氮源,采用溶胶-凝胶法制备不同锻烧温度的纯TiO2、Mn-TiO2及Mn-N-TiO2光催化剂,利用X射线衍射、紫外-可见光漫反射光谱及电子自旋共振等技术对样品形貌和结构进行表征,并以罗丹明B的光催化降解为模型反应,考察不同锻烧温度对其光催化活性的影响.结果表明,Mn、N成功掺入TiO2后,有利于提高光催化剂的热稳定性,抑制锐钛矿相向金红石相转化,且光吸收拓展到可见光区域.Mn、N共掺杂样品比单Mn掺杂样品具有更高的光催化活性,400℃下锻烧的Mn-N-TiO2在可见光下对罗丹明B的降解具有最高的光催化活性,光照2h降解率达到100%.高温锻烧Mn-N-TiO2和Mn-TiO2样品在紫外光照射30min后对罗丹明B的降解率在90%以上.     

氮掺杂TiO2介孔光催化剂降解腐殖酸的研究

 以甲酰胺为氮源,钛酸四丁酯为钛源,P123为模板剂,采用溶胶-凝胶法制备了N-TiO2,并利用X-射线粉末衍射(XRD)、BET、分子荧光(PL)等技术对催化剂进行了表征.结果表明, N-TiO2主要以锐钛矿型存在,加入适量模板剂可使N-TiO2具有介孔结构,比表面积达到111.767m2/g,并能使其光生电子与空穴的复合率降低,采用5%P123制备的N-TiO2催化剂(10g/L),对腐殖酸钠(5mg/L)光催化降解,2h后其降解率可达98%,反应符合一级动力学.     

溴代甲烷在SO42-/TiO2上的光催化降解

采用溶胶-凝胶法制备了SO₄^2-/TiO₂催化剂,运用XRD、BET比表面测定,FTIR等技术对催化剂进行了表征,并在微型常压连续反应装置上进行CH₃Br光催化反应性能考察.结果表明,SO₄^2-引入TiO₂体系使得催化剂的结构和光催化性能得到显著改善.SO₄^2-负载量为9%,烧结温度为450℃时,SO₄^2-/TiO₂催化剂的光催化活性最高;SO₄^2-/TiO₂催化剂对反应物料中的水汽有很好的耐受性;当反应温度低于85℃时,提高反应温度,有利于改善对CH₃Br的光催化反应活性,表观活化能约为19.6kJ·mol^-1,反应温度在85℃～105℃区间时,CH3Br的光催化降解表观活化能为0.     

Combined effects of adsorption and photocatalysis by hybrid TiO2/ZnO-calcium alginate beads for the removal of copper

The use of nanosized titanium dioxide(TiO_2) and zinc oxide(ZnO) in the suspension form during treatment makes the recovering and recycling of photocatalysts difficult.Hence,supported photocatalysts are preferred for practical water treatment applications.This study was conducted to investigate the efficiency of calcium alginate(CaAlg) beads that were immobilized with hybrid photocatalysts,TiO_2/ZnO to form TiO_2/ZnO-CaAlg.These immobilized beads,with three different mass ratios of TiO_2:ZnO(1:1,1:2,and 2:1) were used to remove Cu(Ⅱ) in aqueous solutions in the presence of ultraviolet light.These beads were subjected to three cycles of photocatalytic treatment with different initial Cu(Ⅱ) concentrations(10-80 ppm).EDX spectra have confirmed the inclusion of Ti and Zn on the surface of the CaAlg beads.Meanwhile,the surface morphology of the beads as determined using SEM,has indicated differences of before and after the photocatalytic treatment of Cu(Ⅱ).Among all three,the equivalent mass ratio TiO_2/ZnO-CaAlg beads have shown the best performance in removing Cu(Ⅱ) during all three recycling experiments.Those TiO_2/ZnO-CaAlg beads have also shown consistent removal of Cu,ranging from 7.14-52.0 ppm(first cycle) for initial concentrations of10-80 ppm.In comparison,bare CaAlg was only able to remove 6.9-48 ppm of similar initial Cu concentrations.Thus,the potential use of TiO_2/ZnO-CaAlg beads as environmentally friendly composite material can be further extended for heavy metal removal from contaminated water.     

Preparation, characterization, and photocatalytic activities of boron- and cerium-codoped TiO2

Boron- and cerium-codoped TiO2 photocatalysts were synthesized using modified sol-gel reaction process and characterized by X- ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS）, particle size distribution （PSD）, diffuse reflectance spectra （DRS）, and Brunauer-Emmett-Teller （BET）. The photocatalytic activities were evaluated by monitoring the degradation of dye Acid Red B （ARB）. The results showed that the prepared photocatalysts were mixed oxides mainly consisting of titania, ceria, and boron oxide. The structure of TiO2 could be transformed from amorphous to anatase and then to rutile by increasing calcination temperature; the transformation being accompanied by the growth of particle size without any obvious change in phase structure of CeO2. The XPS of B1.6Ce1.0-TiO2 prepared at 500℃ showed that a few boron atoms were incorporated into titania and ceria lattice, whereas others existed as B2O3. Cerium ions existed in two states, Ce^3＋ and Ce^4＋, and the atomic ratio of Ce^3＋/Ce^4＋ was 1.86. When boron and cerium were doped, the UV-Vis adsorption band wavelength showed an obvious shift toward the visible range （〈526 nm）. As the atomic ratio of Ce/Ti increased to 1.0, the absorbance edge wavelength increased to 481 nm. The absorbance edge wavelength decreased for higher cerium doping levels （Ce/Ti=2.0）. The particles size ranged from 122 to 255 nm with a domain at 168 nm （39.4%）. The degradation of ARB dye indicated that the photocatalytic activities of boron- and cerium-codoped TiO2 were much higher than those of P25 （a standard TiO2 powder）. The activities increased as the boron doping increased, whereas decreased when the Ce/Ti atomic ratio was greater than 0.5. The optimum atomic ratio of B/Ti and Ce/Ti was 1.6 and 0.5, respectively.     

金属泡沫镍负载纳米TiO2光催化降解甲醛和VOCs

采用溶胶-凝胶法制备了3种掺杂金属离子的纳米TiO₂光催化剂,并将其负载于泡沫镍板上,以室内空气典型污染物甲醛和VOCs为模型反应物,研究了对甲醛和VOCs气体的光催化作用并讨论了La³⁺的最佳掺杂比例以及环境因素对光催化效率的影响.结果表明:该TiO₂催化剂具有良好的锐钛矿型结构;负载掺La 1.5%TiO₂的泡沫镍板90min对甲醛和VOCs的降解率分别为94%和87%,远高于未掺:83%和72%,掺Fe     

Photocatalytic degradation of Acid Blue 62 over CuO-SnO2 nanocomposite photocatalyst under simulated sunlight

The novel CuO-SnO2 nanocomposite oxide photocatalysts were prepared by simple co-precipitation method, and characterized by X- ray diffraction, transmission electron microscopy, N2 adsorption-desorption measurement and UV-Vis diffuse reflectance spectroscopy. The photocatalytic activities of CuO-SnO2, evaluated using the photodegradation of Acid Blue 62 as a probe reaction under the irradiation of Xenon light, were also found to be related to the calcination temperature and the molar ratio of Cu to Sn. The maximum photocatalytic activity of the CuO-SnO2 photocatalyst was observed to be calcined at 500~C for 3 h （the molar ratio of Cu to Sn was 1：1） due to the sample with good crystallization and high surface area. It also showed much higher photocatalytic activity in treatment dye wastewater under simulated sunlight irradiation compared to Degussa P25 TiO2.     

不同基质负载的TiO2薄膜光催化性能的比较

采用溶胶凝胶法制备出纳米TiO2粉末、ITO导电玻璃和普通玻璃负载的纳米TiO2薄膜光催化刺。通过对乙酸的降解实验表明：镀膜4次的TiO2／ITO薄膜的催化活性大约是TiO2／giass薄膜的2倍,与等负载量的TiO2粉末相比也具有较高的光催化活性。使用10次后,TiO2／ITO薄膜和TiO2／glass薄膜的光催化活性分别降低了25％和12％。但经再生后,催化活性可恢复至90％左右。     

δ-MnO_2对ZnO和TiO_2光催化降解萘酚蓝黑活性影响

以萘酚蓝黑为模型污染物,采用动力学方法研究了δ-MnO2颗粒杂质对亚微米级商品TiO2(C)、ZnO(C)和纳米级自制TiO2(N)、ZnO(N)光催化作用的影响,并通过紫外-可见漫反射光谱(UV-vis DRS)和荧光光致发光光谱(PL)对试样进行了表征。结果表明,δ-MnO2能导致2种TiO2严重失活,而对2种ZnO的光催化活性影响很小。δ-MnO2导致TiO2光催化剂失活的主要原因为:能提高TiO2的带隙能,以及作为深能级杂质促进光生电子与空穴之间的复合。     

硅钨酸敏化TiO_2的制备及光催化性能研究

以硅钨酸为敏化剂,采用水热法合成了杂多酸敏化光催化剂TiO2-SiW。利用X-射线衍射(XRD)、紫外-可见吸收光谱(UV-vis)等测试手段对样品进行表征,以罗丹明B为模拟污染物评价其光催化活性。XRD结果表明,所得TiO2催化剂为锐钛矿型;UV-vis吸收光谱分析表明,杂多酸敏化使TiO2在可见光区的吸收增强,吸收边红移;光催化实验结果表明,所得TiO2-SiW催化剂光催化活性较好,将催化剂对模拟污染物的处理取得了较好的成果。