BiOCl/MWCNTs复合催化剂对罗丹明B光催化降解研究

以B(iNO3)3.5H2O和NaCl为原料,多壁碳纳米管(MWCNTs)为载体,水解法合成碳纳米管负载氯氧化铋复合型光催化剂(BiOCl/MWCNTs)。通过TEM、XRD、UV-Vis对催化剂的微观形貌、主要成分和光学吸收进行了表征,并以500 W氙灯为可见光光源,研究了其对罗丹明B的光催化降解能力。TEM和XRD结果表明,复合催化剂中BiOCl成块状与MWCNTs结合,粒径小,分散好;UV-Vis则显示,BiOCl/MWCNTs对420⁷80 nm波长段的光的吸收强于BiOCl,有利于可见光催化。光照2.5 h后,BiOCl和BiOCl/MWCNTs对罗丹明B的降解率分别达到78%和96%。BiOCl/MWCNTs对罗丹明B光催化反应符合一级反应动力学特征,速率常数为1.23 h-1,相比BiOCl提高了98.2%。     

微波辅助光催化降解水中苯酚

利用改装的家用微波炉、微波无电极灯(EDLs)和TiO₂催化剂研究了水溶液中苯酚的光催化降解效果.结果表明,反应30 min,微波辅助光催化(MAPC)能去除92%的苯酚,溶液总有机碳(TOC)减少84%.MAPC的最佳反应条件为:苯酚初始浓度10 mg/L,微波功率900 W,反应液体积50 mL,EDLs-3,催化剂用量1～4 g/L,循环态流速15 mL/min.MAPC处理含酚废水具有较好的应用潜能.     

微波辅助光催化降解兽药环丙氨嗪

利用微波光催化实验装置研究了水溶液中兽药环丙氨嗪的光催化降解,探讨了添加微波无电极灯(EDL)对降解反应的促进作用.结果表明,环丙氨嗪在微波辅助1.0g/L TiO2光催化体系中反应20min降解率可达99.6%,检测到的主要降解产物为三聚氰胺.环丙氨嗪在pH3.0~9.0范围内的微波辅助光催化降解率都高于99%;增加TiO2用量和EDL数量均显著提高其降解率.外源添加NO3-离子明显降低了环丙氨嗪的降解率,主要由于NO3-对紫外光的强吸收和在TiO2表面带正电的空穴位的吸附作用.     

喹啉的微波辅助光催化氧化降解研究

对微波辅助紫外光催化(MV/UV/P25)处理喹啉模拟废水的工艺条件进行了实验研究,并比较了MW、UV、UV/曝气、MW/UV/曝气、MW/UV/P25等五种体系下喹啉的降解,结果表明,微波辐射与紫外光催化(MV/UV/P25)在喹啉的降解过程中具有很好的协同作用,在反应进行到lh时,喹啉的去除率达到了64.9%。实验还对MW/UV/P25体系中喹啉降解的影响因素进行了研究。     

微波溶剂热法制备钼酸铋及其光催化性能

采用微波溶剂热法制备了α-Bi2Mo3O12和γ-Bi2Mo O6可见光催化剂,并用XRD、SEM、和UV-Vis等测试手段表征了试样的结构和性能,最后以氯胺磷为目标降解物考察了它们的可见光催化降解性能.结果显示,在p H值较低时产物为α-Bi2Mo3O12,p H较高时产物为γ-Bi2Mo O6,并探讨了不同产物的形成机理.光催化实验结果表明,γ-Bi2Mo O6的可见光催化活性优于α-Bi2Mo3O12;在氯胺磷初始浓度较低时,γ-Bi2Mo O6光催化降解过程符合零级动力学反应模型.在酸性或碱性条件下γ-Bi2Mo O6对氯胺磷的降解效果优于中性条件.     

微波强化光催化对直接耐酸大红4BS的降解

采用微波无极灯强化光催化对直接耐酸大红4BS的降解进行研究。初步考察反应温度、微波功率、pH值、催化剂TiO2浓度、曝气量、直接耐酸大红4BS初始浓度、外加氧化剂H2O2量等因素对直接耐酸大红4BS降解效果的影响。实验结果表明,反应最佳温度是55℃、最佳催化剂TiO2投加量为6 g/L;较低pH值、高微波功率、外加氧化剂H2O2有利于直接耐酸大红4BS的降解。与常规的光催化相比,微波减弱pH值和染料初始浓度对降解效率的影响。在优化工艺参数和未加H2O2条件下,反应4 h后,质量浓度为500 mg/L的直接耐酸大红4BS降解率达到90%。     

微波辅助Bi_2WO_6光催化降解四氯酚研究

采用水热法制备了纳米Bi2WO6,并用X射线衍射仪XRD、透射电镜TEM和比表面积分析仪BET表征其晶相结构、形貌及比表面积;然后以2,3,4,6-四氯酚(TeCP)为目标物考察了Bi2WO6在微波场中的光催化活性;最后探讨了TeCP在微波光催化反应体系中的降解机理。结果表明,微波辅助Bi2WO6光催化能够有效降解TeCP,反应20minTeCP(30mg/L)的去除率为94%,相应的动力学常数为0.191min-1;用GC/MS分析检测了此反应中TeCP的7种降解中间产物:2,3,4-三氯酚、2,3,5-三氯酚、2,3,6-三氯酚、2,4,5-三氯酚、2,4,6-三氯酚、3,4,5-三氯酚和2,3,5,6-四氯酚;推断在微波辅助Bi2WO6光催化反应体系TeCP的降解机理为TeCP异构化、脱氯、三氯酚异构化和矿化。     

石棉尾矿水热合成建筑材料的研究

对利用石棉尾矿水热合成建筑材料进行了研究。结果表明,石棉尾矿预处理的最佳温度为９５０℃,石棉尾矿９０％,ＭＡ和ＮＢ各５％材料的性能较好。     

光催化降解制浆漂白废水试验条件的优化

制浆漂白废水的主要成分之一氯代愈创木酚在TiO2作催化剂、254nm波长的紫外光作光源时,发生光催化降解反应,苯环特征峰在反应过程中逐渐消失。采用正交试验得到较佳的试验条件,结果表明,有机物的初始浓度是一个关键因素,其次是溶液的酸碱度,降解时间的延长可以提高光催化降解效果,同时还要考虑催化剂的用量和反应器的循环流量等工艺参数。在初始浓度为0.05mmol/L、循环流量20L/h、催化剂用量250mg/L、pH值10、反应180min时,降解率达到99%。     

微波无极紫外耦合TiO2光催化降解米诺环素

受抗生素污染的医疗废水排放量逐渐增加,给人类生存环境和身体健康带来极大的危害。该文采用微波无极紫外耦合光催化降解米诺环素的模拟废水,研究了不同pH、H₂O₂投加量和TiO₂投加量对米诺环素去除的影响。在单因素的基础上,进行响应面的优化实验。结果表明：3个因素均能对米诺环素的降解性能产生影响,其影响的显著性为pH>TiO₂投加量>H₂O₂投加量;确定出微波无极紫外耦合光催化降解水中米诺环素的最优条件为pH 3.62、H₂O₂投加量5.48 mmol/L、TiO₂投加量0.47 g/L。在最优条件下,米诺环素的TOC降解率达到96.97%,与预测结果基本符合。     

Photocatalytic degradation of Rhodamine B bymicrowave-assisted hydrothermal synthesized N-doped titanate nanotubes

Microwave-induced nitrogen-doped titanate nanotubes（NTNTs） were characterized by transmission electron microscopy（TEM）, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, Fourier transform infrared spectroscopy（FT-IR）, Zeta potential analysis,specific surface area（SBET）, and UV-Visible spectroscopy. TEM results indicate that NTNTs retain a tubular structure with a crystalline multiwall and have a length of several hundred nanometers after nitrogen doping. XRD findings demonstrate that the crystalline structure of NTNTs was dominated by anatase, which is favored for photocatalytic application. The Ti-O-N linkage observed in the XPS N 1s spectrum is mainly responsible for narrowing the band gap and eventually enhancing the visible light photoactivity. FT-IR results demonstrated the existence of H3O＋, which could be excited by photo-generated holes to form hydroxyl radicals and degrade environmental pollutants. After sintering at 350°C, the UV-Vis absorbance edges of NTNTs significantly shift to the visible-light region, which indicates N atom doping into the nanotubes. Photocatalytic degradation of Rhodamine B（RhB） via NTNTs show good efficiency, with pseudo first-order kinetic model rate constants of 3.7 × 10-3, 2.4 × 10-3and 8.0 × 10-4sec-1at pH 3, 7, and 11, respectively.     

Photocatalytic degradation kinetics and mechanism of pentachlorophenol based on superoxide radicals

Pentachlorophenol could be photocatalytically reduced with superoxide radicals in aqueous solution under simulated sunlight irradiation.     

Ti-MCM-41的微波水热法合成、表征及其催化氧化性质研究

本研究利用微波水热法合成Ti-MCM-41,并采用XRD、FTIR、BET、XPS及TEM等技术对材料进行表征.同时,使用甲基橙溶液作为光催化氧化的对象,对光催化剂的氧化性能进行考察.实验结果表明:利用微波水热法合成Ti-MCM-41,可将合成时间缩短至3 h,能够大大缩减反应时间并节省能源.通过在MCM-41多孔结构中掺杂钛,可明显提高其光催化活性.在酸性溶液中,Ti-MCM-41的催化氧化效率较高.XRD、FTIR、BET、XPS及TEM等表征结果表明,钛成功地掺入到了MCM-41中,并未破坏其多孔有序的结构,Ti-MCM-41同时兼具介孔材料的高比表面积和二氧化钛的光催化性能,有利于在环境污染修复上的应用.     

Rapid synthesis of Ti-MCM-41 by microwave-assisted hydrothermal method towards photocatalytic degradation of oxytetracycline

This study employed microwave-assisted hydrothermal method to synthesize Ti-MCM-41,which are mesoporous materials with a high surface area and excellent photocatalytic ability. Fourier transform infrared spectroscopy(FTIR), X-ray diffraction(XRD), X-ray photoelectron spectroscopy(XPS), transmission electron microscopy(TEM), and ultraviolet–visible spectroscopy(UV–Vis) were employed. The XRD findings showed that Ti-MCM-41 exhibited a peak at 2θ of 2.2°, which was attributed to the hexagonal MCM-41 structure. The BET(Brunauer–Emmett–Teller) results agreed with the TEM findings that Ti-MCM-41 has a pore size of about 3–5 nm and a high surface area of 883 m~2/g. FTIR results illustrated the existence of Si–O–Si and Si–O–Ti bonds in Ti-MCM-41. The appearance of Ti2 p peaks in the XPS results confirmed the FTIR findings that the Ti was successfully doped into the MCM-41 structure. Zeta(ζ)-potential results indicated that the iso-electric point(IEP) of Ti-MCM-41 was at about pH 3.02. In this study, the photocatalytic degradation of oxytetracycline(OTC) at different pH was investigated under Hg lamp irradiation(wavelength 365 nm). The rate constant(K′_(obs)) for OTC degradation was 0.012 min-1at pH 3. Furthermore, TOC(total organic carbon) and high resolution LC–MS(liquid chromatography–mass spectrometry) analyses were conducted to elucidate the possible intermediate products and degradation pathway for OTC. The TOC removal efficiency of OTC degradation was 87.0%, 74.4% and 50.9% at pH 3, 7 and 10, respectively. LC–MS analysis results showed that the degradation products from OTC resulted from the removal of functional groups from the OTC ring.     

非离子表面活性剂在人工光源辐照下的光催化降解

在光催化氧化对5种典型非离子表面活性剂（NIS）和实际印染废水中NIS的去除效果的实验中,未见TiO₂有明显催化作用．光解30min,几种NIS的光降解率均达60％以上．NIS的光降解速率受NIS浓度和DO的影响较小;pH值降低有利于NIS的光降解,而在中性或弱酸性条件下,NIS光降解效率仍较好;投加H₂O₂可提高NIS的光降解速率,最适投加量为4.4×10^-4mol/L．对于实际印染废水,NIS的光降解去除率比生化法高且处理时间短得多,同时对COD、MBAS亦有较好的去除效果,表明光催化氧化是一项很有前途的NIS处理技术．     

Bi2WO6可见光催化降解活性艳红X-3B的研究

采用水热合成法制备Bi2WO6催化剂,并通过XRD,UV-vis DRS等手段对其进行表征;以活性艳红X-3B为目标污染物,研究催化剂量、X-3B初始浓度、反应溶液pH值以及H2O2等因素在可见光辐射下对其光催化降解效果的影响.结果表明,所制备的Bi2WO6催化剂结晶度好,具有较强的可见光吸收能力;最佳催化反应条件为: X-3B初始浓度20mg/L,Bi2WO6用量2g/L, pH5.18(原始pH值).在此条件下,光照60min,对X-3B的去除率可达到86%;加入2mL/L 30%的H2O2,光照30min,降解率可达到96%以上,降解反应符合一级反应动力学.光催化反应可以有效地破坏X-3B的发色基团偶氮结构使其脱色,但在所设定的反应时间(80 min)内X-3B不能被完全矿化,反应过程中有中间产物生成.     

Photocatalytic degradation of organochlorine compounds using TiO2 supported on fiberglass cloth

１ＩｎｔｒｏｄｕｃｔｉｏｎＯｒｇａｎｏｃｈｌｏｒｉｎｅｃｏｍｐｏｕｎｄｓａｒｅｗｉｄｅｌｙｕｓｅｄｉｎｖａｒｉｏｕｓｉｎｄｕｓｔｒｉｅｓ，ａｎｄｈａｖｅｂｅｎｒｅｐｏｒｔｅｄｔｏｃｏｎｔａｍｉｎａｔｅｒｕｎｎｉｎｇｗａｔｅｒ，ｒｉｖｅｒｓ，ｌａｋｅｓ...     

铁基催化剂的微波水热处理对其SCR脱硝性能的影响

利用微波对共沉淀制备的铁铈钛复合氧化物催化剂前驱体进行水热处理,探讨了微波水热处理对铁基催化剂低温SCR脱硝性能的优化;并对微波水热处理条件的影响进行了正交分析.结果表明:对铁基催化剂前驱体进行微波水热处理,可提高其低温SCR脱硝性能,使其脱硝温度窗口向低温偏移;且微波水热处理的低温优化效果与催化剂中Fe/Ti摩尔比密切相关,Fe/Ti摩尔比越小,微波水热处理的低温优化越强;微波加热方式和微波辐射时间会影响微波水热处理对铁基催化剂SCR脱硝性能的低温优化;在相同微波辐射时间条件下,当P30逐渐变为P80,微波水热处理对铁基催化剂低温SCR脱硝的促进作用降低;在P30条件下,微波辐射15min使铁基催化剂具有最佳低温SCR脱硝活性.     

Photocatalytic degradation of dye effluent by titanium dioxide pillar pellets in aqueous solution

Photocatalytic oxidation (PCO) process is an effective way to deal with organic pollutants in wastewater which could be difficult to be degraded by conventional biological treatment methods. Normally the TiO2 powder in nanometre size range was directly used as photocatalyst for dye degradation in wastewater. However the titanium dioxide powder was arduous to be recovered from the solution after treatment. In this application, a new form of TiO2(i. e. pillar pellets ranging from 2.5 to 5.3 mm long and with a diameter of 3.7 mm) was used and investigated for photocatalytic degradation of textile dye effluent. A test system was built with a flat plate reactor(FPR) and UV light source(blacklight and solar simulator as light source respectively) for investigating the effectiveness of the new form of TiO2. It was found that the photocatalytic process under this configuration could efficiently remove colours from textile dyeing effluent. Comparing with the TiO2 powder, the pellet was very easy to recovered from the treated solution and can be reused in multiple times without the significant change on the photocatalytic property. The results also showed that to achieve the same photocatalytic performance, the FPR area by pellets was about 91% smaller than required by TiO2 powder. At least TiO2 pellet could be used as an alternative form of photocatalyst in applications for textile effluent treatment process, also other wastewater treatment processes.     

Effect of sulfur source on photocatalytic degradation performance of CdS/MoS2 prepared with one-step hydrothermal synthesis

Cd S/Mo S_2,an extremely efficient photocatalyst,has been extensively used in hydrogen photoproduction and pollutant degradation.Cd S/Mo S_2can be synthesized by a facile one-step hydrothermal process.However,the effect of the sulfur source on the synthesis of Cd S/Mo S_2via one-step hydrothermal methods has seldom been investigated.We report herein a series of one-step hydrothermal preparations of Cd S/Mo S_2using three different sulfur sources:thioacetamide,L-cysteine,and thiourea.The results revealed that the sulfur source strongly affected the crystallization,morphology,elemental composition and ultraviolet(UV)–visible-light-absorption ability of the Cd S/Mo S_2.Among the investigated sulfur sources,thioacetamide provided the highest visible-light absorption ability for Cd S/Mo S_2,with the smallest average particle size and largest surface area,resulting in the highest efficiency in Methylene Blue(MB)degradation.The photocatalytic activity of Cd S/Mo S_2synthesized from the three sulfur sources can be arranged in the following order:thioacetamideL-cysteinethiourea.The reaction rate constants(k)for thioacetamide,L-cysteine,and thiourea were estimated to be 0.0197,0.0140,and 0.0084 min~(-1),respectively.However,thioacetamide may be limited in practical application in terms of its price and toxicity,while L-cysteine is relatively economical,less toxic and exhibited good photocatalytic degradation performance toward MB.