Contamination of wild-grown edible mushrooms by heavy metals in a former mercury-mining area

The aim of this study was to evaluate the contamination of six edible wild species of mushrooms (Boletus pulverulentus, Cantharellus cibarius, Lactarius quietus, Macrolepiota procera, Russula xerampelina and Suillus grevillei) by heavy metals (Hg, Cd, Pb, Zn, Cu, Ni, Cr, Co, Mn and Fe). Mushroom samples were collected from sites contaminated by emissions from mining and processing of polymetallic ores in operation during the period 1969–1993 in Rudňany, southeast Slovakia. The four study sites spanned up to a 5-km distance from the emission source. The collected mushroom samples were analyzed using Flame Atomic Absorption Spectrophotometry and/or Flame Atomic Absorption Spectrophotometry with graphite furnace. Mercury, Cd and, in some samples, also Pb present the highest risks in terms of contamination of the food chain following subsequent consumption. The content of two metals in the dry matter (dm) of the mushrooms exceeded the limits set by the European Union (EU; Cd: 0.5 mg/kg dm, Pb: 1.0 mg/kg dm). The highest mean contents of the eight metals recorded for S. grevillei were 52.2, 2.15, 107, 104, 2.27, 2.49, 81.6 and 434 mg/kg dm for Hg, Pb, Zn, Cu, Ni, Cr, Mn and Fe, respectively. The highest content of Cd was recorded in M. procera (3.05 mg/kg dm) and that of Co in L. quietus (0.90 mg/kg dm). The calculated weekly intake for Hg, Pb and Cd shows that regular consumption of mushrooms from the studied area poses risks to human health.     

汞、铅、铬污染土壤的微生物修复

利用裂褶菌(Schizophyllum commune)GGHN08-116菌株,以棉籽壳、玉米秸等为固体发酵底物修复受汞、铅、铬污染的土壤。通过菌丝穿透重度重金属土壤实验,研究了菌丝在穿透土壤过程对交换态重金属的影响以及该菌株子实体对重金属离子的富集能力,同时,通过盆栽实验研究了在重度重金属污染土壤上,施用不同比例的固体发酵料对污染土壤中汞、铅、铬及其胡萝卜根茎质量、产量的影响,研究结果表明,该菌株能穿透厚度为5 cm的土壤,并有子实体生成,土壤pH值略有下降,与对照差异不显著;与对照相比,土壤中交换态汞、铬含量均显著下降,而交换态铅差异不显著,子实体中除汞含量符合标准外,铅、铬均超出了GB 7096-2003,GB 2762-2005规定标准。在固体发酵料处理下土壤中交换态汞、铅、铬含量均显著下降,胡萝卜根茎中均未检测到汞、铅含量,铬含量也符合GB 2762-2005规定标准。GGHN08-116菌株及其固体发酵产物具有修复受重金属污染土壤的能力。     

Heavy metal contamination in the vicinity of an industrial area near Bucharest

BACKGROUND, AIMS AND SCOPE: Chromium enters into the aquatic environment as a result of effluent discharge from steel works, electroplating, leather tanning industries and chemical industries. As the Cr(VI) is very harmful to living organisms, it should be quickly removed from the environment when it happens to be contaminated. Therefore, the aim of this laboratory research was to develop a rapid, simple and adaptable solvent extraction system to quantitatively remove Cr(VI) from polluted waters. METHODS: Aqueous salt-solutions containing Cr(VI) as CrO4(2-) at ppm level (4-6 ppm) were prepared. Equal volumes (5 ml) of aqueous and organic (2-PrOH) phases were mixed in a 10 ml centrifuge tube for 15 min, centrifuged and separated. Concentrations of Cr(VI), in both the aqueous and organic phases, were determined by atomic absorption spectrometry. The effects of salt and acid concentrations, and phase-contact time on the extraction of Cr(VI) were investigated. In addition, the extraction of Cr(VI) was assessed in the presence of tetramethylammonium chloride (TMAC) in 2-PrOH phase. Effects of some other metals, (Cd(II), Co(II), Cu(II), Ni(II) and Zn(II)), on the extraction of Cr(VI) were also investigated. RESULTS AND DISCUSSION: The Cr(VI) at ppm level was extracted quantitatively by salting-out the homogeneous system of water and 2-propanol(2-PrOH) using chloride salts, namely CaCl2 or NaCl, under acidic chloride media. The extracted chemical species of Cr(VI) was confirmed to be the CrO3Cl-. The ion-pair complex extracted into the organic phase was rationalized as the solvated ion-pair complex of [2-PrOH2+, CrO3Cl-]. The complex was no longer stable. It implied the reaction between extracted species. Studies revealed that salts and acid directly participated in the formation of the above complex. Use of extracting agents (TMAC) didn't show any significant effect on the extraction of Cr(VI) under high salting-out conditions. There is no significant interference effect on the extraction of Cr(VI) by the presence of other metals. The Cr(VI) in the organic phase was back-extracted using an aqueous ammonia solution (1.6 mol dm(-3)) containing 3 mol dm(-3) NaCl. The extraction mechanism of Cr(VI) is also discussed. CONCLUSIONS: Salting-out of homogeneous mixed solvent of 2-propanol can be employed to extract Cr(VI) quantitatively, as an ion-pair of [2-PrOH2+ * CrO3Cl-] solvated by 2-PrOH molecules. Then, the complex becomes 'solvent-like' and is readily separated into the organic phase. The increase of Cl- ion concentration in the aqueous phase favors the extraction. The 2-PrOH, salts and acid play important roles in the extraction process. There is no need to use an extracting agent at a high salting-out condition. RECOMMENDATIONS AND PERSPECTIVES: Chromium(VI) must be quickly removed before it enters into the natural cycle. As the 2-PrOH is water-miscible in any proportion, ion-pairing between 2-PrOH2+ and CrO3Cl- becomes very fast. As a result, Cr(VI) can easily be extracted. Therefore, the method is recommended as a simple, rapid and adaptable method to quickly separate Cr(VI) from aqueous samples.     

Equilibrium, kinetic, and thermodynamic biosorption of Pb(II), Cr(III), and Cd(II) ions by dead anaerobic biomass from synthetic wastewater

Purpose

Heavy metals are toxic pollutants released into the environment as a result of different industrial activities. Biosorption of heavy metals from aqueous solutions is a new technology for the treatment of industrial wastewater. The aim of the present research is to highlight the basic biosorption theory to heavy metal removal.

Materials and methods

Heterogeneous cultures mostly dried anaerobic bacteria, yeast (fungi), and protozoa were used as low-cost material to remove metallic cations Pb(II), Cr(III), and Cd(II) from synthetic wastewater. Competitive biosorption of these metals was studied.

Results

The main biosorption mechanisms were complexation and physical adsorption onto natural active functional groups. It is observed that biosorption of these metals was a surface process. The main functional groups involved in these processes were hydroxyl (–OH) and carboxylic groups (C=O) with 37, 52, and 31 and 21, 14, and 34 % removal of Pb(II), Cr(III), and Cd(II), respectively. Langmuir was the best model for a single system. While extended Langmuir was the best model for binary and ternary metal systems. The maximum uptake capacities were 54.92, 34.78, and 29.99 mg/g and pore diffusion coefficients were 7.23, 3.15, and 2.76?×?10^?11 m²/s for Pb(II), Cr(III), and Cd(II), respectively. Optimum pH was found to be 4. Pseudo-second-order was the best model to predict the kinetic process. Biosorption process was exothermic and physical in nature.

Conclusions

Pb(II) offers the strongest component that is able to displace Cr(III) and Cd(II) from their sites, while Cd(II) ions are the weakest adsorbed component.     

Heavy metals contents in agricultural topsoils in the Ebro basin (Spain). Application of the multivariate geoestatistical methods to study spatial variations

In this work the content of seven heavy metals (Cd, Cr, Cu, Hg, Ni, Pb and Zn) and other parameters (the pH, organic matter, carbonates and granulometric fraction) in agricultural topsoil in the Ebro basin are quantified, based on 624 samples collected according to an 8 by 8 km square mesh. The average concentrations (mg/kg) obtained were: Cd 0.415+/-0.163, Cr 20.27+/-13.21, Cu 17.33+/-14.97, Ni 20.50+/-22.71, Pb 17.54+/-10.41, Zn 17.53+/-24.19 and Hg 35.6+/-42.05 microg/kg. The concentration levels are relatively low in areas of high pH and low organic matter content concentration. The results of factor analysis group Cd, Cu, Hg, Pb and Zn in F1 and Cr y Ni in F2. The spatial heavy metals component maps based on geostatistical analysis, show definite association of these factors with the soil parent material. The local anomalies (found in Cu, Zn and Pb) are attributed to anthropogenic influence.     

Heavy metal (Cd, Cr, Cu, Hg, Pb, Zn) concentrations in seven fish species in relation to fish size and location along the Yangtze River

Purpose

The objective of this paper is to assess the regulation of the accumulation of heavy metals in the aquatic environment and different fish species.

Methods

Water and fish samples were collected from upper to lower reaches of the Yangtze River. The heavy metal (Cd, Cr, Cu, Hg, Pb, Zn) concentrations in the muscle tissue of seven fishes were measured. Additionally, the relationships between heavy metal concentrations in fish tissue and fish size (length and weight), condition factor, water layer distribution, and trophic level were investigated.

Results

Metal concentrations (milligrams per kilogram wet weight) were found to be distributed differently among different fish species. The highest concentrations of Cu (1.22?mg/kg) and Zn (7.55?mg/kg) were measured in Pelteobagrus fulvidraco, the highest concentrations of Cd (0.115?mg/kg) and Hg (0.0304?mg/kg) were measured in Silurus asotus, and the highest concentrations of Pb (0.811?mg/kg) and Cr (0.239?mg/kg) were measured in Carassius auratus and Cyprinus carpio. A positive relationship was found between fish size and metal level in most cases. The variance of the relationships may be the result of differences in habitat, swimming behavior, and metabolic activity. In this study, fishes living in the lower water layer and river bottom had higher metals concentrations than in upper and middle layers. Benthic carnivorous and euryphagous fish had higher metals concentrations than phytoplankton and herbivorous fish. Generally, fish caught from the lower reach had higher metals concentrations than those from the upper reach.

Conclusions

Cadmium and lead concentrations in several fishes exceeded the permissible food consumption limits, this should be considered to be an important warning signal.     

Biosorption of heavy metals from aqueous solution by UV-mutant Bacillus subtilis

To develop an efficient bio-immobilization approach for the remediation of heavy metal pollution in soil, a mutant species of Bacillus subtilis (B38) was obtained by ultraviolet irradiation and selection under high concentration of cadmium (Cd) in a previous study. In the present study, to check the applicability of this mutated species to the sorption and immobilization of other metals, the sorption of four heavy metals, Cd, chromium (Cr), mercury (Hg), and lead (Pb), on living and nonliving B38 in single- and multiple-component systems under different conditions was investigated using batch experiments. Rapid metal binding occurred on both living and nonliving B38 during the beginning of the biosorption. The sorption kinetics followed the exponential equation for living biomass and the pseudo-first-order Lagergren model for nonliving biomass, with r ² values in the range of 0.9004-0.9933. The maximum adsorptive quantity of the heavy metals on B38 changed with the solution pH, temperature, biomass dose, and ionic strength. The nonliving biomass generally showed greater or similar adsorptive capacities as compared with the living biomass and was not likely to be affected by the solution parameters. The bacterium had a stronger affinity to the cationic heavy metals than to the anionic one, and the equilibrium sorption amounts were 210.6, 332.3, and 420.9 mg/g for Cd(II), Hg(II), and Pb(II), respectively. The results of binary and ternary sorption experiments indicated that the metals with the higher sorption capacity in the single-component systems showed greater inhibitory effects on the biosorption of other metal ions in the multiple-component systems, but the sorption sites of Hg and Cd or Pb are likely to be different. The results of this study illustrated that the mutant species is a promising biosorbent for the remediation of multiple heavy metals.     

Vertical Profile of Acid Volatile Sulfide (AVS) and Risk Assessment of Sediments from Baihua Lake,China

Acid volatile sulfide (AVS), simultaneously extracted metals (SEMs), and total concentrations of trace elements (Cu, Cd, Pb, Zn, Ni, Hg, As, and Cr) were studied in sediment cores from Baihua Lake in southwest China. The molar ratios of SEMs to AVS for all samples were lower than 1.0 except for the 25- to 30-cm layer of the sample collected at location YPZ, indicating that the heavy metals were currently not significantly bioavailable as a whole to benthic organisms. Based on the sediment quality guidelines and the potential ecological risk assessment, Hg presented a high ecological risk for the water body.     

XANES study of Cr sorbed by a kitchen waste compost from water

A kitchen waste compost was used to sorb Cr for various times from water containing either Cr(NO3)3 or CrO3 in different concentrations. Scanning electron microscopy (SEM) results show that the composts have been partially oxidized by Cr(VI) during the sorption experiments. X-ray absorption near edge structure (XANES) simulation suggests that about 54.1-61.0% Cr sorbed on the compost is in form of organic Cr(III) through ionic exchange process with the rest being existent as Cr(NO3)3 in the Cr(III) sorption case; no Cr(OH)3 is observed or expected because the solution pH after sorption experiments is or= 5.94. Moreover, organic Cr(III) represents about 51.7-69.0% of the total sorbed Cr, and the rest (6.1-28.5%) is Cr(VI).     

Heavy metal concentrations in marine molluscs from the Moroccan coastal region

Mussels (Mytilus galloprovincialis), clams (Venerupis decussatus) and oysters (Crassostrea gigas) were sampled seasonally during 2004-2005, from different coastal environments of Morocco in order to measure their accumulated heavy metal concentrations. The concentrations of Hg and Pb were determined by AFS and ICP-MS methods, respectively, whilst the remaining metals (Cd, Cr, Cu, Mn, Zn and Ni) were quantified by AAS. The soft tissue concentrations of the mussels were on average 7.2 mg kg(-1) (Cd), 9.6 mg kg(-1) (Pb), 0.6 mg kg(-1) (Hg), 26.8 mg kg(-1) (Cu), 8.8 mg kg(-1) (Cr), 292 mg kg(-1) (Zn), 20.8 mg kg(-1) (Mn) and 32.8 mg kg(-1) (Ni). The highest tissue heavy metal concentrations were recorded in the south from the industrial area of Jorf Lasfar. The relationships between metal concentration and season in each species showed very similar annual profiles with a peak observed around spring-summer. Statistical analysis indicated that different species showed different bioaccumulation of metals depending on study site and season.     

淀粉基黄原酸盐处理重金属废水的条件优化研究

采用淀粉基黄原酸盐处理含重金属的电镀废水 ,对淀粉基黄原酸盐的用量、pH值和反应时间等条件进行了研究。结果发现 ,1L含氰电镀废水 (含Cr3+15mg/L、Cu2 +3mg/L、Ni2 +9.2mg/L和Zn2 +6mg/L) ,加入 1g淀粉基黄原酸盐 ,调节 pH为 8,搅拌 1h ,过滤 ,处理后的废水中Cr3+、Cu2 +、Zn2 +和Ni2 +残余浓度分别为 0 .0 8mg/L、0 .0 1mg/L、0 .1mg/L和 0 .0 8mg/L。含有重金属盐的残渣 ,可用硝酸处理 ,以回收重金属     

乌梁素海表层沉积物重金属与营养元素含量的统计分析

对乌梁素海表层沉积物营养盐与重金属的分布情况进行研究,应用SPSS统计分析软件对乌梁素海表层沉积物重金属与营养元素进行相关分析和因子分析,并对重金属元素进行聚类分析。营养元素与重金属间的相关分析表明：重金属元素Cu、Cr、Pb和Cd相互间具有极显著的正相关性;有机质与As和Hg呈极显著的正相关;总氮与Hg呈极显著相关,与As呈显著相关,而与Pb呈极显著负相关,与Cd呈显著负相关;总磷与As呈显著负相关。重金属元素间的R-型聚类分析结果将本论文研究的9种金属元素分为3类。采用主成分分析法对乌梁素海表层沉积物重金属与营养元素进行因子分析,得到4个因子,并进一步分析讨论了各主成分的科学内涵。     

Influence of glyphosate and its formulation (Roundup) on the toxicity and bioavailability of metals to Ceriodaphnia dubia

This study examined the toxicological interaction between glyphosate (or its formulation, Roundup) and several heavy metals to a freshwater cladoceran, Ceriodaphnia dubia. We demonstrated that all binary combinations of Roundup and metals (Cd, Cu, Cr, Ni, Pb, Se and Zn) exhibited "less than additive" mixture toxicity, with 48-h LC50 toxic unit > 1. Addition of glyphosate alone could significantly reduce the acute toxicity of Ag, Cd, Cr, Cu, Ni, Pb and Zn (but not Hg and Se). The ratio between glyphosate and metal ions was important in determining the mitigation of metal toxicity by glyphosate. A bioaccumulation study showed that in the presence of glyphosate the uptake of some metals (e.g. Ag) was halted but that of others (e.g. Hg) was increased significantly. Therefore, our study strongly suggests that glyphosate and its commercial formulations can control the toxicity as well as the bioavailability of heavy metals in aquatic ecosystems where both groups of chemicals can co-occur.     

Potential risk assessment of heavy metals by consuming shellfish collected from Xiamen, China

Concentrations of Hg, Pb, Cd, and Cr in 240 shellfish including oyster, short-necked clam, razor clam, and mud clam collected from six administrative regions in Xiamen of China were measured. The daily intakes of heavy metals through the consumption of shellfish were estimated based on both of the metal concentrations in shellfish and the consuming amounts of shellfish. In addition, the target hazard quotients (THQ) were used to evaluate the potential risk of heavy metals in shellfish on human body. Results showed that the concentrations of heavy metals in shellfish ranged at the following sequence: Cr > Cd > Pb > Hg. The concentrations of Hg and Pb in most samples were below the limits (0.3 mg?kg^?1 for Hg and 0.5 mg?kg^?1 for Pb) of national standard (GB 18406.4-2001) set in China. About 57 % of samples were found to contain more than 0.1 mg?kg^?1 of Cd, in which the highest level was found in oyster from Xiangan with a value of 1.21 mg?kg^?1. The average concentrations of Cd in oyster and mud clam samples were 0.338 and 0.369 mg?kg^?1, respectively, which were significantly higher (p?<?0.05) than those in the samples of short-necked clam and razor clam. The highest concentration of Cr was found to present in short-necked clam from Jimei with a value of 10.4 mg?kg^?1, but a mean value of 1.95 mg?kg^?1 in all the shellfish was observed, and no significant difference was found among the different sampling regions. The calculated daily intakes of Hg, Pb, Cd, and Cr through consuming the shellfish were 0.005, 0.122, 0.137, and 1.20 μg?kg^?1 day^?1, respectively, which accounted for 2.19, 3.42, 13.7, and 40.1 % of the corresponding tolerable limits suggested by the Joint FAO/WHO Expert Committee on Food Additives. The THQ values of the four metals were far below 1 for most samples, except for those of Cd and Cr in the four shellfish species with the mean values of 0.132 and 0.385, respectively. The highest THQ values of Cd were observed in the species of oyster (0.719) and mud clam (0.568). But the high THQ values of Cr observed in all the four species were derived from the applied reference dose (RfD) data of Cr(VI) due to the unavailable RfD value of total Cr. The results indicate that the intakes of heavy metals by consuming shellfish collected from Xiamen of China do not present an appreciable hazard risk on human health, but attention should be paid to consuming those with relatively high THQ values, such as oyster, mud clam, and short-necked clam.     

Effect of humic substance on thermal treatment of chromium(VI)-containing latosol soil

Latosol soils contaminated with chromium(VI) [Cr(VI)], which is hazardous, can be recycled as raw materials for porcelain and construction sectors if a proper thermal stabilization process is implemented. This study investigates how thermal treatment affects Cr behavior during the sintering of latosol and deorganic latosol samples; both samples are artificially contaminated with CrO3. Approaches including X-ray absorption spectroscopy, scanning electron microscopy, N2-based Brunauer Emmett Teller surface analyzer, thermogravimetric analyzer/differential scanning calorimeter, and the toxicity characteristic leaching procedure promulgated by Taiwan Environmental Protection Administration are used in this study. After drying the Cr(VI)-contaminated latosol (i.e., containing 37,120 mg of Cr/kg sample) at 105 degrees C, approximately 80% of the doped CrO3 is chemically reduced to Cr(OH)3 by a humic substance naturally existing in the soil. In contrast, in the organics-free CrO3-contaminated latosol dried at 105 degrees C, only 9% of the doped CrO3 is reduced to Cr(OH)3. Heating the samples at 500 and 1100 degrees C transforms hazardous Cr(VI) into Cr(III) that is negligibly toxic; Cr2O3, which is insoluble, is detected as the most abundant Cr species. Moreover, formation of Cr2SiOs, which is suggested to relate to low Cr leaching, is only detected in the sample heated at 1100 degrees C. Surface morphology, surface area, and thermogravimetric analyzer/differential scanning calorimeter results demonstrate that thermal treatment at 1100 degrees C can incur considerable soil sintering/ melting if the humic substance in the soil has been heated off previously. Finally, Cr concentrations in the toxicity characteristic leaching procedure leachates collected from the samples thermally treated at 1100 degrees C for 4 hr are < or =0.21 mg of Cr L(-1) that are much less than the Taiwan Environmental Protection Administration regulatory limit (<5 mg of Cr L(-1)); consequently, these two samples are nonhazardous, and they have the potential for resource recycling. Conversely, Cr concentrations in the leachates from all 500 degrees C and 105 degrees C samples are in the 25.6-1279 mg L(-1) range.     

Localization of Hg and Pb in the palps,the digestive gland and the gills in Mytilus galloprovincialis (L.) using autometallography and X-ray microanalysis

The intracellular localization of heavy metals using autometallography (AMG) and X-ray microanalysis was studied in the palps, the digestive gland and the gills of mussels Mytilus galloprovincialis, after an experimental exposure to 0.1 mg l(-1) of Hg and 0.1 mg l(-1) of Pb, for 30 and 60 days. In the examined tissues, autometallographical black silver deposits (BSD) were localized mainly in the residual bodies and heterolysosomes of the digestive cells, as well as in the dense bodies of the epithelial cells. Metal deposition after Hg exposure was much more abundant compared to Pb exposure. Using X-ray microanalysis, Hg was traced on the BSD in all examined tissues, while Pb was not traced in these deposits. The results are discussed in comparison to previous results on long-term exposure to the same metals; in addition, the palps are introduced as a new metal storing organ and, finally, the use of X-ray microanalysis under a scanning electron microscope in order to enhance the specificity of AMG is suggested.     

菌丝体表面分子印迹壳聚糖吸附剂对Cr3+的吸附性能研究

菌丝体表面分子印迹吸附剂所保留的印迹对过渡金属离子有着良好的吸附作用,以Cr3 作为吸附离子,系统研究了该吸附剂的吸附特性和影响因素.结果表明:吸附剂对Cr3 的饱和吸附容量可达60 mg/g;其吸附行为满足Langmuir方程式.初始浓度为200 mg/L时,最佳吸附pH在3～4,吸附容量可达到50 mg/g左右,离子强度对吸附没有影响,用0.5 mol/L硝酸或硫酸解吸Cr3 ,解吸率在90%以上.     

Sorption of Cr(VI) from dilute solutions and wastewater by live and pretreated biomass of Aspergillus flavus

Sorption of Cr(VI) was carried out from dilute solutions using live and pretreated biomass in a batch mode. Effects of agitation time, adsorbent dosage and pH were examined. The autoclaved biomass that showed maximum adsorption capacity (Q(0)=0.335 mg g(-1)) was used as an adsorbent in column studies. The optimized flow rate of 2.5 ml min(-1) and bed height 10 cm were used to determine the effect of metal ion concentration on removal of Cr(VI). Applying the BDST model to calculate the adsorption capacity (N(0)) of column, which showed 4.56 x 10(-5), 7.28 x 10(-5), 6.89 x 10(-5), 3.07 x 10(-5), 2.80 x 10(-5)mg g(-1) for 4, 8, 12, 16 and 20 mg dm(-3) of Cr(VI), respectively. Batch sorption proved to be more efficient than the column sorption and hence batch sorption was used to remove Cr(VI) from a textile dyeing industry wastewater. The phytotoxic effect of treated and untreated wastewater was studied against Zea mays. Toxicity was reduced by 50% in the treated effluent.     

Removal of Pb(II), Cd(II), Cu(II), and Zn(II) by hematite nanoparticles: effect of sorbent concentration, pH, temperature, and exhaustion

Nanoparticles offer the potential to improve environmental treatment technologies due to their unique properties. Adsorption of metal ions (Pb(II), Cd(II), Cu(II), Zn(II)) to nanohematite was examined as a function of sorbent concentration, pH, temperature, and exhaustion. Adsorption experiments were conducted with 0.05, 0.1, and 0.5 g/L nanoparticles in a pH 8 solution and in spiked San Antonio tap water. The adsorption data showed the ability of nanohematite to remove Pb, Cd, Cu, and Zn species from solution with adsorption increasing as the nanoparticle concentration increased. At 0.5 g/L nanohematite, 100 % Pb species adsorbed, 94 % Cd species adsorbed, 89 % Cu species adsorbed and 100 % Zn species adsorbed. Adsorption kinetics for all metals tested was described by a pseudo second-order rate equation with lead having the fastest rate of adsorption. The effect of temperature on adsorption showed that Pb(II), Cu(II), and Cd(II) underwent an endothermic reaction, while Zn(II) underwent an exothermic reaction. The nanoparticles were able to simultaneously remove multiple metals species (Zn, Cd, Pb, and Cu) from both a pH 8 solution and spiked San Antonio tap water. Exhaustion experiments showed that at pH 8, exhaustion did not occur for the nanoparticles but adsorption does decrease for Cd, Cu, and Zn species but not Pb species. The strong adsorption coupled with the ability to simultaneously remove multiple metal ions offers a potential remediation method for the removal of metals from water.     

Influence of redox mediators and metal ions on synthetic acid dye decolourization by crude laccase from Trametes hirsuta

In this paper, the effect of redox mediators on synthetic acid dye decolourization (Sella Solid Red and Luganil Green) by laccase from Trametes hirsuta cultures has been investigated. All the redox mediators tested, 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS), 1-hydroxybenzotriazole (HBT) and Remazol Brilliant Blue R (RBBR), led to higher activities than those obtained without mediators addition showing the suitability of the laccase/mediator system (LMS) in the decolourization of acid dyes. HBT was by far the most effective mediator, showing a decolourization percentage of 88% in 10 min for Sella Solid Red and of 49% in 20 min for Luganil Green. On the other hand, the stability of laccase against several metal ions, normally found in textile wastewater, was assessed. Laccase was stable at a concentration of 1mM for 7d against all the metal ions tested except for Zn+2, CrO4(-2), Cd+2, Cr2O7(-2), Fe+2, Cu+2 and especially Hg+2. When the concentration was increased to 10mM laccase stability decreased against all the metals assayed, in particular against Fe+2. In addition, the effect of metal ions on the decolourization process was also studied. It was found that Hg+2 inhibited the dye decolourization process, being the presence of HBT absolutely required for dye decolourization.