有机颜料废水的混凝预处理研究

利用絮凝剂阳离子聚丙烯酰胺(CPAM)和混凝剂聚合氯化铝(PAC)对有机颜料废水进行混凝处理,考察了单独使用CPAM、PAC及两者联合使用的处理效果,探讨了初始pH值、混凝剂投加量对处理效果的影响.结果表明,CPAM与PAC复配处理该废水时效果较好,水样pH值为7.0;CPAM与PAC的投药量分别为10mg/L和150mg/L时,浊度去除率可达97.56％.     

PAC和PASS对印染废水的混凝效果研究

主要研究PAC和PASS混凝剂对高浓度和低浓度印染废水的混凝处理效果。确定了PAC处理高浓度印染废水(pH:4.39;色度:18750倍;COD:6480;浊度:1462)的最佳pH、混凝时间、投药量为5～7、8min、24mL/L;PASS处理低浓度印染废水(pH:10.16;色度:2020倍;COD:168;浊度:36.4)的最佳pH、混凝时间、投药量为6～7、15min、12mL/L。PAC处理高浓度的印染废水效果较好,处理低浓度印染废水的效果较差;PASS处理低浓度印染废水的处理效果比PAC要好。     

黄浦江上游原水强化处理选炭试验研究

以黄浦江上游水源为原水,通过煤质炭、竹质炭、椰壳炭等炭种筛选小试和中试试验,研究了黄浦江上游原水中有机污染物强化去除的最佳炭种及其最佳投加量。结果表明黄浦江上游原水中投加PAC能够改善处理后水质,提高原水中有机物的去除效果;并且随着PAC投加量的增加,原水中有机物去除效果增强;综合性价比、碳源等因素确定竹质炭较为经济合理;当竹质炭投加量为10～15mg/L时,处理后出水CODMn可达到3mg/L或以下。     

纳米零价铁去除磷酸盐机理研究

纳米零价铁(nanoscale zero-valent iron,nZVI)颗粒具有独特核-壳结构,使其具有较强氧化还原特性,比表面积大和表面活性高等特点,因此被广泛用于不同环境介质中多种污染物的去除修复。本研究采用传统的液相化学还原法合成nZVI颗粒并用于去除水溶液中的磷酸盐。通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线衍射仪(XRD)表征nZVI颗粒的性质。实验研究了nZVI投加量、PO3-4初始浓度、溶液初始pH值对nZVI去除PO3-4效率的影响及微米零价铁(micro-ZVI)和nZVI去除PO3-4的对比。实验结果表明,当PO3-4初始浓度为20mg/L时,随着nZVI投加量从200mg/L增加到1000mg/L,PO3-4去除效率从32.94%上升到90.17%;当nZVI投加量为600mg/L时,随着PO3-4初始浓度从10mg/L增加到100mg/L,PO3-4去除效率从87.33%下降到45.77%;当nZVI投加量为600mg/L且PO3-4初始浓度为20mg/L,溶液pH分别为3和4时,PO3-4去除效率分别为83.63%和92.36%;nZVI和mZVI投加量均为600mg/L且PO3-4初始浓度为10mg/L,nZVI的PO3-4去除率(87.33%)是mZVI(8.86%)的9.86倍。研究结果表明,nZVI能够高效去除水体中的磷酸盐,主要去除机理是吸附和化学沉淀的双重作用。     

Exploitation of Trichoderma harzianum mycelial waste for the removal of rhodamine 6G from aqueous solution

The harvested mycelial waste of Trichoderma harzianum was used as an adsorbent for the removal of rhodamine 6G and was studied in batch mode. The effects of agitation time and initial dye concentration, adsorbent dosage and pH were examined. The study revealed that the amount of dye adsorbed (mgg(-1)) increased with increase in agitation time and reached equilibrium after 120 min, for dye concentrations of 10-50 mg L(-1). The adsorbent dosage of 1.0 g/50 mL and pH of 8.0 were found to be optimum for maximum dye removal. The batch mode adsorption data followed both the Langmuir and Freundlich isotherms. The pseudo first- and second-order rate kinetics were applied to the adsorbent system. The adsorption kinetics of rhodamine 6G showed that the pseudo-second-order kinetic model provided the best correlation of the equilibrium data. The study implies that it is possible to develop a dye removal system by using T. harzianum biomass, which occurs as sludge in waste stream of fermentation industries.     

高锰酸钾强化混凝处理化工废水生化尾水

高锰酸钾氧化技术是提高混凝工艺去除有机污染物的有效途径之一。与其他方法相比,采用高锰酸钾氧化法作为混凝工艺的前处理工艺具有反应速度快、处理效率高、适用范围广等优点。实验采用高锰酸钾强化混凝处理生化尾水,考察了高锰酸钾投加量、反应时间、反应pH以及不同混凝剂组合的因素的影响。结果表明,COD,TOC,UV254等污染物的去除率随着高锰酸钾投加量的增加而增加;在高锰酸钾投加量小于12 mg/L时,反应时间不应大于40 min;高锰酸钾对有机物的去除存在最优的pH,pH在6~7范围内,有机物去除率较高;高锰酸钾与不同混凝剂组合工艺相比于单独投加高锰酸钾或直接混凝剂混凝,COD去除率明显提高。高锰酸钾与聚合氯化铝组合混凝工艺对有机污染物的去除效果较其他组合工艺好。     

高浓度土霉素废水预处理工艺的试验研究

本试验采用混凝沉淀和气浮工艺处理高浓度土霉素废水,结果表明,作为预处理工艺,这套工艺在技术上是可行的;在石灰投加量为1500mg/L、PAC投加量为2250mg/L、PAM投加量为4mg／L的条件下,混凝沉淀的CODcr去除率达到75．8％,BOD5／CODcr的值由原来的0.15提高到0.32。     

茄子秸杆活性炭对染料废水的吸附性能研究

以茄子秸秆为原料,ZnCl2为活化剂制备粉末状活性炭,主要研究了活性炭对染料废水的吸附性能;以活性红X-3B和酸性蓝RL为模型染料,考察了染料初始浓度、pH值、活性炭投加量和吸附时间等对染料脱色率的影响。结果表明,染料初始浓度和活性炭投加量对染料脱色率影响较大。初始浓度为300mg／L时,活性炭的最佳投加量分别为1g／L和1．4g／L;在最佳工艺条件下,脱色率分别在93％和98％以上,COD去除率分别为94．5％和86．4％,出水水质达到国家一级《纺织染整工业水污染物排放标准》（GB 4287—1992）。     

高浓度油田压裂废水降低CODCr的预处理方法

针对高浓度油田压裂废水黏度高、浊度大、含油量高等特点,强化预处理工艺,降低CODCr值。文章通过实验证明了强氧化剂(Fenton试剂)与混凝剂PAC+PAM相结合的工艺可有效降低高浓度含油废水CODCr值,进而通过Fenton试剂与混凝剂的投药量、pH值等因素对高浓度油田压裂废水的影响进行分析,得出采用该化学预处理方法出水水质清澈,可直接进入生化处理系统进行后续处理。     

Fenton试剂处理六氯苯废水的试验研究

研究了采用Fenton法处理六氯苯模拟废水的方法以及Fenton法处理六氯苯的影响因素。研究结果显示:在H2O2(30%)投加量为500mg/L,Fe2 投加量为1000mg/L,pH=2.5的条件下,经过4h的反应,废水中HCB去除率可达51.65%。     

Characterization and coagulation of a polyaluminum chloride (PAC) coagulant with high Al13 content

A polyaluminum chloride (PAC) coagulant was prepared from AlCl3 x 6H2O and Na2CO3. The Al13 species in PAC was separated and purified by the SO4(2-)/Ba2+ deposition-replacement method, and characterized by 27Al-NMR and XRD. From 27Al-NMR spectroscopy, it was found that PAC obtained after separation and purification contained more Al13 (PAC-Al13, for short) than original PAC before separation and purification. In XRD spectra, a strong Al13 signal appeared in the range of 2theta from 5 to 25 degrees. Jar tests were performed to test the coagulation efficiency of AlCl3, PAC and PAC-Al13 in treating synthetic or actual water samples. Compared with PAC and AlCl3, PAC-Al13 gives the best results for turbidity, humic acid and color removal, and achieves the highest charge-neutralizing ability. Under the study conditions, PAC-Al13 gave about 90% humic acid removal and almost 100% reactive blue dye removal when its dosages were 4.0 and 15 mg/L as Al, respectively. The Al13 species has a higher positive charge and is the most effective polymeric Al species in water and wastewater treatment.     

Effect of pH and alum dosage on the efficiency of microalgae harvesting via flocculation technique

Microalgae biomass is well known as a potential sustainable product for bio-based industry, which has reported encountering numerous difficulties during biomass harvesting and recovering. This study examined the effect of pH (5–12) and alum dosage (30–180 mg/L) for microalgae Botryococcus sp. harvested via flocculation technique. The optimum pH condition for Botryococcus sp. harvesting was measured to be 9.2, and the alum dosage was 100 mg/L. Both optimum values successfully harvested up to 95% microalgae biomass. This study revealed that flocculation efficiencies for alum are highly dependent on the range of pH and coagulant dosage that were applied during the process. Use of flocculation technique with alum as a coagulant represents a convenient technique for Botryococcus sp. biomass harvesting and is recommended for use in both small- and large-scale biomass industries.     

城市污水Al盐化学除磷的试验研究

针对新疆地区污水厂总磷去除效率有限,出水总磷存在超标排放风险的问题。试验中采用自配不同总磷含量的生活污水,通过小试试验,投加AlCl3进行试验室模拟化学除磷试验。研究结果表明:进水总磷浓度为2～4mg/L时,投加AlCl3/TP质量比为8.6;进水总磷浓度为6mg/L时,投加AlCl3/TP质量比上升到13.1,出水总磷浓度均<0.5mg/L,AlCl3投加不会改变污水的pH值,化学沉淀最佳时间为30min。建议设计除磷沉淀池的停留时间为25min～30min。     

UV-H_2O_2联用工艺去除水中阿特拉津的研究

采用间歇式反应器考察了UV-H2O2高级氧化技术去除水中阿特拉津的效果及其影响因素,并进行了相关的反应动力学研究。结果表明,在pH值6.9,阿特拉津初始浓度500μg/L,紫外辐照强度172μW/cm2时,H2O2投加量50mg/L,反应10min后,阿特拉津的去除率90%。UV-H2O2联用工艺对阿特拉津的降解符合一级反应动力学。H2O2在该联用工艺降解阿特拉津中具有双重作用,一方面,当H2O2投加量较小时,一级反应速率常数随H2O2投加量的增加基本呈现线性增加的趋势;另一方面,当H2O2浓度增加到一定程度(90mg/L)后,阿特拉津的降解速率随H2O2浓度的变化已不明显,而H2O2浓度为102mg/L时,则出现了抑制作用。     

The application of bioflocculant for the removal of humic acids from stabilized landfill leachates

The evaluation of bioflocculant, in comparison with traditional inorganic coagulants, for the removal of humic acids from landfill leachates stabilized by biological treatment, was performed using conventional jar-test coagulation experiments. The optimized conditions (pH and coagulant dosage) were identified for the treatment of synthetic solutions as well as for biologically pre-treated landfill leachates. It was found that the application of bioflocculant was quite efficient in the removal of humic acids from synthetic solutions as well as in the reduction of COD content from real landfill leachates. The optimal pH value was found to be between 7 and 7.5, while a 20 mg/l bioflocculant dosage was sufficient in providing more than 85% humic acid removal. The results were comparable with those obtained by the application of conventional coagulants such as alum or polyaluminum chloride; therefore, bioflocculant can be considered as a viable alternative in the treatment of landfill leachates applying coagulation.     

RD复合净水剂对阳离子染料RL的吸附脱色

考察了RD复合净水剂吸附处理阳离子艳兰染料RL废液的实验条件,探讨了RD吸附脱色的实质。结果表明,加入0.3gRD到浓度为200mg/L的染液中,在25℃、pH=7.0条件下,吸附时间为10m in时,废液的脱色率达到80%,RD单位质量吸附量为10.7mg/g;当50mg/L的染料废液中,RD的投加量为0.2g时,脱色率达到了96%以上,RD单位质量吸附量为8.12mg/g;pH值和温度对吸附脱色效果影响不显著,而且RL废液的浓度增大,RD单位质量吸附量增大,但是脱色率有所下降。RD对染料的吸附符合Langmu ir吸附模型。     

Electrocoagulation of vegetable oil refinery wastewater using aluminum electrodes

Electrocoagulation with aluminum electrodes was used to treat the vegetable oil refinery wastewater (VORW) in a batch reactor. The effects of operating parameters such as pH, current density, PAC (poly aluminum chloride) dosage and Na(2)SO(4) dosage on the removal of organics and COD removal efficiency have been investigated. It has been shown that the removal efficiency of COD increased with the increasing applied current density and increasing PAC and Na(2)SO(4) dosage and the most effective removal capacity was achieved at the pH 7. The results indicate that electrocoagulation is very efficient and able to achieve 98.9% COD removal in 90 min at 35 mAcm(-2) with a specific electrical energy consumption of 42 kWh(kgCOD(removed))(-1). The effluent was very clear and its quality exceeded the direct discharge standard.     

超声-双氧水和亚铁离子体系处理含酚废水研究

在实验装置上对超声-双氧水和亚铁离子体系联合处理含酚废水进行了实验研究。主要考察了废水初始pH值、初始双氧水浓度、超声功率、反应时间等因素对酚去除率的影响。实验结果表明：超声辐射可以在双氧水和亚铁离子体系氧化过程中起加速反应的作用，而且随着超声功率的增大，加速反应的能力增强；实验条件下废水初始pH值为4～6．8，初始双氧水浓度为140mg／L时酚去除效果最佳；超声-双氧水和亚铁离子体系处理含酚废水过程中苯酚的降解规律符合表现一级反应。     

PAC和PAM复合絮凝剂在洗涤剂废水处理中的应用研究

絮凝性能的实验研究表明,PAC和PAM复合絮凝剂是处理洗涤剂废水的理想絮凝剂,采用该复合絮凝剂处理洗涤剂废水时的最佳操作条件如下：PAC用量为1．5g／L,PAM用量为10mg／L,pH值约为7．0,絮凝搅拌速度60r／min,絮凝搅拌时间30min,沉淀池沉淀时间为30min。该实验结果在中试规模的应用中得到了较好地验证,中试试验研究表明采用PAC和PAM复合絮凝剂处理洗涤剂废水,CODCr和LAS(直链烷基苯璜酸钠)去除率分别可达85％和72％以上,有效地解决了LAS难以生物降解等问题。     

Color removal from dye-containing wastewater by magnesium chloride

Color removal by MgCl(2) when treating synthetic waste containing pure dyes was studied. The color removal efficiency of MgCl(2)/Ca(OH)(2) was compared with that of Al(2)(SO(4))(3), polyaluminum chloride (PAC) and FeSO(4)/Ca(OH)(2). The mechanism of color removal by MgCl(2) was also investigated. The experimental results show that the color removal efficiency of MgCl(2) is related to the type of dye and depends on the pH of the waste and the dosage of the coagulants used. Treatment of waste containing reactive dye or dispersed dye with MgCl(2) yielded an optimum color removal ratio when the pH of the solution was equal to or above 12.0. For both the reactive and dispersed dye waste, MgCl(2)/Ca(OH)(2) was shown to be superior to MgCl(2)/NaOH, Al(2)(SO(4))(3), PAC and FeSO(4)/Ca(OH)(2) for color removal. A magnesium hydroxide precipitate formed at pH values greater than 12.0, which provided a large adsorptive surface area and a positive electrostatic surface charge, enabling it to remove the dyes through charge neutralization and an adsorptive coagulating mechanism. So, the MgCl(2)/Ca(OH)(2) system is a viable alternative to some of the more conventional forms of chemical treatment, especially for treating actual textile waste with high natural pH.