Reactions of the amine-containing drugs fluoxetine and metoprolol during chlorination and dechlorination processes used in wastewater treatment

The reactivities of the amine-containing pharmaceuticals fluoxetine and metoprolol with hypochlorite were studied using conditions that simulate wastewater disinfection including neutral pH (7.0), a range of reaction times (2–60 min), and a molar excess of hypochlorite relative to the pharmaceutical concentration (5.7 times). The reactions were monitored using liquid chromatography (LC) with several detection modes including ultraviolet absorbance (UV), mass spectrometry (MS), and post-column reaction/reductive electrochemistry (EC) for determining active chlorine products. At levels of 10 μM, both compounds reacted rapidly (<2 min) to form principally N-chloramine products that were stable in aqueous solution for at least 1 h. The reaction was also studied in wastewater, and similar reactivity was noted. These results demonstrate that the cations fluoxetine and metoprolol are likely to be rapidly transformed into neutral N-chloramines during wastewater disinfection. The reactivity of the N-chloramines was also studied with sulfite to simulate dechlorination, which is often employed in wastewater treatment. Both N-chloramines reacted slowly with sulfite. In the pure water dechlorination experiments, it was estimated that 70% and 10% of the peak areas remained after 2 min reaction time for fluoxetine and metoprolol, respectively. At longer reaction times both N-chloramines had been completely reduced by sulfite, and the product of the sulfite reduction reaction was the parent pharmaceutical amine. Since typical dechlorination times in wastewater treatment are on the order of seconds, this suggests the chloramines formed from these two basic drugs might evade dechlorination and be released into the environment. The implications of chloramine release are discussed.     

GC × GC—A New Analytical Tool For Environmental Forensics

Comprehensive two-dimensional gas chromatography, GC × GC, is a new analytical tool with a tremendous capability to separate and identify organic compounds in complex environmental samples. GC × GC uses two different chromatography columns coupled serially by a modulator to produce a volatility by polarity separation and distribute compound peaks across a two-dimensional retention time plane. The two-dimensional separation produces an order of magnitude more resolved peaks than traditional GC methods. The grouping or ordering of the peaks in the GC × GC chromatogram facilitates the identification of unknown compounds and the comparison of complex environmental samples. When a mass spectrometer detector is used, each resolved GC × GC peak yields a single-component, interference-free mass spectrum that leads to accurate matching with mass spectral libraries. GC × GC examination of marine sediment extracts identified a wide variety of chemical contaminants including polychlorinated biphenyls, p -nonylphenol isomers, polycyclic aromatic hydrocarbons, benzotriazoles, and the alkane, cycloalkane, alkylbenzene, alkylnaphthalene, and biomarker fractions of petroleum. The two-dimensional GC × GC chromatogram image permits rapid screening of the sediment extracts for these and other unknown contaminants.     

Dechlorination of hexachlorobenzene using lead–iron bimetallic particles

Synthesized lead–iron (Pb/Fe) bimetallic particles were applied to dechlorinate hexachlorobenzene (HCB) under various conditions (e.g. bimetal amount, initial pH value, reaction temperature, and reaction duration). The results showed that adding Pb onto Fe benefited the dechlorination of HCB and the bimetal with 1.4% Pb content performed best. The degradation rate decreased regularly as the initial pH value of the aqueous increased from 1.9 to 11.1 except for pH 7.0 where the fastest dechlorination rate emerged. The dechlorination could be enhanced by increasing the amount of Pb/Fe or the reaction temperature. The dechlorination ratio of HCB within 15 min increased from 24.3% to 81.3% when Pb/Fe amount increased from 0.1 g to 0.8 g. The dechlorination followed pseudo-first-order kinetics, and the dechlorination rate constants were 0.0027, 0.0064, 0.0157, and 0.0321 min^?1 at 25, 50, 70, and 85 °C, respectively, and the activation energy (E_a) of the dechlorination by Pb/Fe was 37.86 kJ mol^?1.     

Analysis of particulate polycyclic aromatic hydrocarbons by on-line coupled supercritical fluid extraction–liquid chromatography–gas chromatography–mass spectrometry

An on-line supercritical fluid extraction–liquid chromatography–gas chromatography–mass spectrometry (SFE–LC–GC–MS) method was developed for the analysis of the particulate polycyclic aromatic hydrocarbons (PAHs). The limits of detection of the system for the quantification standards were in the range of 0.25–0.57 ng, while the limits of determinations for filter samples varied from 0.02 to 0.04 ng m⁻³ (24 h sampling). The linearity was excellent from 5 to 300 ng (R²>0.967). The analysis could be carried out in a closed system without tedious manual sample pretreatment and with no risk of errors by contamination or loss of the analytes. The results of the SFE–LC–GC–MS method were comparable with those for Soxhlet and shake-flask extractions with GC–MS. The new method was applied to the analysis of PAHs collected by high-volume filter in the Helsinki area to study the seasonal trend of the concentrations. The individual PAH concentrations varied from 0.015 to more than 1 ng m⁻³, while total PAH concentrations varied from 0.81 to 5.68 ng m⁻³. The concentrations were generally higher in winter than in summer. The mass percentage of the total PAHs in total suspended particulates ranged from 2.85×10⁻³% in July to 15.0×10⁻³% in December. Increased emissions in winter, meteorological conditions, and more serious artefacts during the sampling in summer season may explain the concentration profiles.     

Investigations into a novel method for atmospheric polycyclic aromatic hydrocarbon monitoring

A novel analytical method for atmospheric polycyclic aromatic hydrocarbons (PAHs) was developed based on laser induced fluorescence (LIF) of samples on quartz multi-channel polydimethylsiloxane traps. A tunable dye laser with a frequency doubling crystal provided the excitation radiation, and a double monochromator with a photomultiplier tube detected emitted fluorescence. The method allowed for the rapid (<5 min), cost effective analysis of samples. Those yielding interesting results could be further analysed by direct thermal desorption-gas chromatography–mass spectrometry (TD–GC–MS, with limits of detection of ～0.3 ng m^?3), as photodegradation was minimal (<10% over 5 min irradiation). Small amounts of naphthalene photodegradation products identified by TD–GC–MS after >15 min irradiation, included phenol, benzyl alcohol and phthalic anhydride. Without any signal optimization, a LIF detection limit of ～1 μg m^?3 was established for naphthalene using a diffusion tube (diffusion rate of 2 ng s^?1) and 292 nm excitation.     

Removal and reductive dechlorination of triclosan by Chlorella pyrenoidosa

Triclosan that is widely used as antimicrobial agent has been detected as contaminant in various aquatic environments. In this work, removal and biodegradation of triclosan in water by using a ubiquitous green alga, Chlorella pyrenoidosa was investigated. When C. pyrenoidosa was exposed to a series concentration of triclosan from 100 to 800 ng mL⁻¹, more than 50% of triclosan was eliminated by algal uptake from the culture medium during the first 1 h exposure and reached equilibrium after the 6 h treatment. In the biodegradation experiments, a removal percentage of 77.2% was obtained after C. pyrenoidosa was cultivated with 800 ng mL⁻¹ triclosan for 96 h. A major metabolite from the reductive dechlorination of triclosan was identified by using liquid chromatography coupled with electrospray ionization-mass spectrometry. The ultrastructural morphology of algal cells grown in the presence of triclosan was observed by using transmission electron microscopy and the growth of algal cells was detected. It was found that the trilcosan treatment resulted in the disruption of the chloroplast and the release of organic material into aquatic environment, which indicated that triclosan may affect membrane metabolism.     

Emissions of volatile fatty acids from feed at dairy facilities

Recent studies suggest that dairy operations may be a major source of non-methane volatile organic compounds in dairy-intensive regions such as Central California, with short chain carboxylic acids (volatile fatty acids or VFAs) as the major components. Emissions of four VFAs (acetic acid, propanoic acid, butanoic acid and hexanoic acid) were measured from two feed sources (silage and total mixed rations (TMR)) at six Central California Dairies over a fifteen-month period. Measurements were made using a combination of flux chambers, solid phase micro-extraction fibers coupled to gas chromatography mass spectrometry (SPME/GC–MS) and infra-red photoaccoustic detection (IR-PAD for acetic acid only). The relationship between acetic acid emissions, source surface temperature and four sample composition factors (acetic acid content, ammonia-nitrogen content, water content and pH) was also investigated. As observed previously, acetic acid dominates the VFA emissions. Fluxes measured by IR-PAD were systematically lower than SPME/GC–MS measurements by a factor of two. High signals in field blanks prevented emissions from animal waste sources (flush lane, bedding, open lot) from being quantified. Acetic acid emissions from feed sources are positively correlated with surface temperature and acetic acid content. The measurements were used to derive a relationship between surface temperature, acetic acid content and the acetic acid flux. The equation derived from SPME/GC–MS measurements predicts estimated annual average acetic acid emissions of (0.7 + 1/?0.4) g m^?2 h^?1 from silage and (0.2 + 0.3/?0.1) g m^?2 h^?1 from TMR using annually averaged acetic acid content and meteorological data. However, during the summer months, fluxes may be several times higher than these values.     

Levels of persistent organic pollutants in air in China and over the Yellow Sea

The occurrence of persistent toxic substances (PTS) in China and possibly their regional transport in the Yellow and East China Seas region was studied. Organochlorines in atmospheric gas-phase and particulate matter were collected by high-volume sampling (filters and polyurethane foams) during 2 weeks in June 2003 (dry season) simultaneously at a Yellow Sea coastal site in an urban area, Qingdao, China, and a rural island site, Gosan, Jeju Island, Korea. Using GC methods, the samples were analysed for 9 persistent organic pollutants (POPs) regulated under the global POP convention, namely aldrin, chlordane (cis- and trans-isomers CC and TC), DDT and metabolites (o,p′-DDT, p,p′-DDD, and p,p′-DDE), dieldrin, endrin, heptachlor, hexachlorobenzene (HCB), mirex and PCB (congeners number 28, 52, 101, 153 and 180), and for hexachlorocyclohexane (α-, β- and γ-isomers), a PTS and now considered for regulation under the convention, too. At the coastal site additionally o,p′-DDE and -DDD, β-endosulfan, isodrin, heptachlorepoxide and δ-HCH, and at the island site additionally p,p′-DDT and 12 additional PCB congeners were analysed. 9 samples were collected at the coastal and 15 (for PCBs 5) at the island site. Long-range advection pathways were determined based on analysed back-trajectory calculations.The mean concentrations of DDT and its metabolites, HCB, HCH, and PCB at the coast were in the 100–1000 pg m⁻³ range. Higher concentrations prevailed during nighttime. The levels were in general lower at the island site, but not for DDT. Local sources are likely. PCBs were even 2 orders of magnitude lower, suggesting that PCBs are not subject to regional transport but elevated concentrations in air are limited to the source areas. Organochlorine pesticide levels on the other hand were seemingly determined by regional transport over Mainland China rather than by emissions in the coastal area. The currently used pesticides mirex and chlordane were found at elevated levels, i.e. 79 (6.6–255) and 36 (<6–71) pg m⁻³, respectively, at the coast but not over the island. The POPs pesticides aldrin, dieldrin and endrin, never registered in China, were mostly found at <10 pg m⁻³ except for endrin at the coastal site (up to 400 pg m⁻³) and aldrin at the island site (up to 50 pg m⁻³).     

Characteristics of chlorofluorocarbons (CFCs) emitted from a municipal waste treatment facility

The emission concentrations of several chlorofluorocarbons (CFCs) were measured from a municipal waste treatment facility (located in Seoul, Republic of Korea) to investigate the emission characteristics of CFCs in the urban environment. To this end, a total of five CFCs (CFC-10, CFC-11, CFC-20, CFC-30, and CFC-113) were analyzed by the thermal desorption–gas chromatography–mass spectrometry (TD–GC–MS) method. The results of this study indicate that the formation of CFC-11 (8.21 ± 1.68 ppb in spring) and CFC-20 (3.92 ± 3.93 ppb in spring) proceeded very actively within the facility. Moreover, CFC-113 was also found in relatively high concentrations (3.34 ± 1.31 ppb in spring) in the treatment facility. Unlike other CFCs, CFC-10 was observed mainly at ambient (and reference) locations and one point inside the treatment facility. In conclusion, emissions of some important CFCs are a prominent process, as they were measured either frequently or abundantly both in winter and spring. It is further indicated that certain CFCs (like CFC-11 and CFC-30) are subject to highly significant seasonal variations.     

Measurements of atmospheric nitrous acid and nitric acid

A highly sensitive technique for the measurement of atmospheric HONO and HNO₃ is reported. The technique is based on aqueous scrubbing using two coil samplers, followed by conversion of HNO₃ to nitrite, derivatization of nitrite to a highly light-absorbing azo dye with sulfanilamide (SA) and N-(1-naphthyl) ethylenediamine (NED), and high performance liquid chromatography (HPLC) analysis. HNO₃ concentration was obtained by the difference of the two channels. Two scrubbing solutions were used for sampling the two species: a 1-mM phosphate buffer solution (pH 7) for the measurement of HONO and a 180 mM NH₄Cl/NH₃ buffer solution (pH 8.5) for the measurement of HONO+HNO₃. The scrubbing solution flow rate was 0.24 ml min⁻¹ and the gas sampling flow rate was 2 l min⁻¹. HNO₃ in the NH₄Cl/NH₃ buffer solution was quantitatively reduced to nitrite along an on-line 0.8-cm Cd reductor column. Nitrite in both channels was derivatized with 2 mM SA and 0.2 mM NED in 25 mM HCl. Quantitative derivatization was achieved within 5 min at 55°C. The azo dye derivative was then separated from the SA/NED reagent by reversed-phase HPLC and detected with a UV-vis detector at 540 nm. With an on-line SEP-PAK C-18 cartridge for the reagent purification, the method detection limit is estimated to be better than 1 pptv for HONO and about 20 pptv for HNO₃. The sample integration time was about 2 min and the sampling frequency is every 10 min. Data collected in downtown Albany and Whiteface Mountain, NY, are shown as examples of applications of this technique in both urban and remote clean environments.     

Optical and microphysical properties of severe haze and smoke aerosol measured by integrated remote sensing techniques in Gwangju,Korea

Aerosol optical and microphysical parameters from severe haze events observed in October 2005 at Gwangju, Korea (35.10°N, 126.53°E) were determined from the ground using a multi-wavelength Raman lidar, a sunphotometer, and a real-time carbon particle analyzer and from space using satellite retrievals. Two different aerosol types were identified based on the variability of optical characteristics for different air mass conditions. Retrievals of microphysical properties of the haze from the Raman lidar indicated distinct light-absorbing characteristics for different haze aerosols originating from eastern and northern China (haze) and eastern Siberia (forest-fire smoke). The haze transported from the west showed moderately higher absorbing characteristics (SSA = 0.90 ± 0.03, 532 nm) than from the northern direction (SSA = 0.96 ± 0.02). The organic/elemental carbon (OC/EC) ratio varied between 2.5 ± 0.4 and 4.1 ± 0.7.     

Determination of priority pesticides in water samples combining SPE and SPME coupled to GC–MS. A case study: Suquía River basin (Argentina)

This study reports a combined method using solid phase extraction (SPE), followed by solid phase microextraction (SPME) to concentrate different pesticides, including chlorinated, organophosphorus, triazines, pyretroids and chloroacetamides, present at trace levels in water samples. Identification and quantification was carried out by gas chromatography coupled to Mass Spectrometry (GC–MS). The optimized methodology showed LOQs at ng L^?1 levels (ranging 0.2–3.5 ng L^?1) in addition to acceptable precision and robustness (recoveries ranged 63–104%, RSD from 4% to 23%), presenting a novel method to reach trace levels, similar to that obtainable using EC detector, with structural confirmation by MS during the analysis of a wide range of environmental pollutants.This method was applied to the study of temporal and spatial distribution of pesticides in the Suquía River basin (Córdoba-Argentina). As expected, highest levels of agrochemicals were observed in areas with intensive agricultural practices, being atrazine (max. = 433.9 ng L^?1), alpha-cypermetrine (max. = 121.7 ng L^?1) and endosulfan sulfate (max. = 106.7 ng L^?1) predominant. In urban areas, the prevalent pesticide was alpha-cypermethrine. These results draw attention to the need of pesticide monitoring programs in rivers, considering both urban and rural sections.     

Use of thermal desorption–gas chromatography–mass spectrometry (TD–GC–MS) on identification of odorant emission focus by volatile organic compounds characterisation

Volatile organic compounds (VOCs) from several different municipal solid wastes’ treatment plants in Mallorca (Spain) have been analysed by thermal desorption–gas chromatography–mass spectrometry (TD–GC–MS). Ambient (immission) air was collected during February and March 2011 by active sampling onto sorbents Tenax™ TA and Carboxen™ 1000. The study presents the chemical characterisation of 93 volatile organic compounds (VOCs) from an overall set of 84 immission air samples. 70 VOCs were positively identified.The linear fit for all 93 external standard calibration, from 10 mg L⁻¹ to 150 mg L⁻¹ (n = 4), was within the range 0.974 < r² < 0.998. Limits of detection of the method (LOD) for all the standards were within the range 1.1–4,213 pg, as the absolute standard amount spiked into sorbent tubes in 1 μL standard mixture (dissolved in methanol).Overall results stated systematic correlation between waste’s nature and VOCs’ air composition. Organic wastes show main contribution of terpenes, waste water sludge residues’ of reduced sulphured compounds (RSCs) and municipal solid wastes show contribution of a wide sort of VOCs. The use of a chemometric approach for variable’s reduction to 12 principal components enables evaluation of similarities and dissimilarities between facilities. PCA clearly related samples to its corresponding facility on the basis of their VOCs composition and the ambient temperature.     

Evaluation of ion exchange resins for the removal of dissolved organic matter from biologically treated paper mill effluent

In this study, the efficiency of six ion exchange resins to reduce the dissolved organic matter (DOM) from a biologically treated newsprint mill effluent was evaluated and the dominant removal mechanism of residual organics was established using advanced organic characterisations techniques. Among the resins screened, TAN1 possessed favourable Freundlich parameters, high resin capacity and solute affinity, closely followed by Marathon MSA and Marathon WBA. The removal efficiency of colour and lignin residuals was generally good for the anion exchange resins, greater than 50% and 75% respectively. In terms of the DOM fractions removal measured through liquid chromatography–organic carbon and nitrogen detector (LC–OCND), the resins mainly targeted the removal of humic and fulvic acids of molecular weight ranging between 500 and 1000 g mol^?1, the portion expected to contribute the most to the aromaticity of the effluent. For the anion exchange resins, physical adsorption operated along with ion exchange mechanism assisting to remove neutral and transphilic acid fractions of DOM. The column studies confirmed TAN1 being the best of those screened, exhibited the longest mass transfer zone and maximum treatable volume of effluent. The treatable effluent volume with 50% reduction in dissolved organic carbon (DOC) was 4.8 L for TAN1 followed by Marathon MSA – 3.6 L, Marathon 11 – 2.0 L, 21K-XLT – 1.5 L and Marathon WBA – 1.2 L. The cation exchange resin G26 was not effective in DOM removal as the maximum DOC removal obtained was only 27%. The resin capacity could not be completely restored for any of the resins; however, a maximum restoration up to 74% and 93% was achieved for TAN1 and Marathon WBA resins. While this feasibility study indicates the potential option of using ion exchange resins for the reclamation of paper mill effluent, the need for improving the regeneration protocols to restore the resin efficiency is also identified. Similarly, care should be taken while employing LC–OCND for characterising resin-treated effluents, as the resin degradation is expected to contribute some organic carbon moieties misleading the actual performance of resin.     

Heterogeneous reactivity of pyrene and 1-nitropyrene with NO2: Kinetics,product yields and mechanism

The heterogeneous reactivity of nitrogen dioxide with pyrene and 1-nitropyrene (1NP) adsorbed on silica particles has been investigated using a fast-flow-tube in the absence of light. Reactants and products were extracted from particles using pressurised fluid extraction (PFE) and concentration measurements were performed using gas chromatography/mass spectrometry (GC/MS). The pseudo-first order rate constants were obtained from the fit of the experimental decay of particulate polycyclic compound concentrations versus reaction time. Experiments were performed at three different NO₂ concentrations and second order rate constants were calculated considering the oxidant concentration. The following rate constant values were obtained at room temperature: k(NO₂ + pyrene) = (9.3 ± 2.3) × 10^?17 cm³ molecule^?1 s^?1 and k(NO₂ + 1NP) = (6.2 ± 1.5) × 10^?18 cm³ molecule^?1 s^?1, showing that the reactivity of 1NP was slower by a factor of 15 than that of pyrene. 1NP was identified as the only NO₂-initiated oxidation product of pyrene and all the three dinitropyrenes were identified in the case of the 1NP reaction. The product quantification allowed showing that the kinetics of oxidation product formation was equal to that measured for parent compounds degradation, within uncertainties, confirming the validity of the reaction kinetics measurements.     

Compound specific carbon and hydrogen stable isotope analyses of volatile organic compounds in various emissions of combustion processes

This study presents carbon (δ¹³C) and hydrogen (δD) isotope values of volatile organic compounds (VOCs) in various emission sources using thermal desorption–gas chromatography–isotope ratio mass spectrometry (TD–GC–irMS). The investigated VOCs ranged from C6 to C10. Samples were taken from (i) car exhaust emissions as well as from plant combustion experiments of (ii) various C3 and (iii) various C4 plants. We found significant differences in δ values of analysed VOCs between these sources, e.g. δ¹³C of benzene ranged between (i) −21.7 ± 0.2‰, (ii) −27.6 ± 1.6‰ and (iii) −16.3 ± 2.2‰, respectively and δD of benzene ranged between (i) −73 ± 13‰, (ii) −111 ± 10‰ and (iii) −70 ± 24‰, respectively. Results of VOCs present in investigated emission sources were compared to values from the literature (aluminium refinery emission). All source groups could be clearly distinguished using the dual approach of δ¹³C and δD analysis. The results of this study indicate that the correlation of compound specific carbon and hydrogen isotope analysis provides the potential for future research to trace the fate and to determine the origin of VOCs in the atmosphere using thermal desorption compound specific isotope analysis.     

Estimation of fluorine and chlorine emissions from Spanish structural ceramic industries. The case study of the Bailén area,Southern Spain

This paper assesses F and Cl emissions as atmospheric pollutants in the Bailén area (southern Spain), originated from the raw material used in structural ceramic industries. The area is one of the most important in Spain, with a daily output over three million pieces. The Bailén area features three categories of industries taking into account F emissions (the most important pollutant from ceramic clays):Group I: Those releasing less than 150 ppm F, which use raw materials with low F contents and/or high proportion of calcite, and fire at about 850°C.Group II: Those releasing 150–300 ppm F, whose raw materials show low calcite percentages and bricks are fired between 850–1050°C.Group III: Those releasing more than 300 ppm F, which use clays containing over 1000 ppm F and firing temperatures around 900°C.The emission rate of F increases with increasing F content in the raw material and firing temperature (particularly when exceeding 1000°C). The calcite and clay mineral contents control the F emissions up to 950°C; on the other hand, a high heating rate hinders fluorine emission to some extent. The emission rate of Cl increases with increasing temperature, but in the most cases chlorine is released at concentrations below 30 ppm.Atmospheric contamination in the Bailén area can reach 3 kg/h of fluorine and up to twice of chlorine emission levels permitted, owing to the massive production of structural clay products.     

Urban roadside aromatic hydrocarbons in three cities of the Pearl River Delta,People's Republic of China

Urban roadside levels of benzene, toluene, ethylbenzene and xylenes (BTEX) were investigated in three typical cities (Guangzhou, Macau and Nanhai) in the Pearl River Delta Region of south China. Air samples were collected at typical ground level microenvironments by multi-bed adsorbent tubes. The BTEX concentrations were determined by thermal desorption–gas chromatography–mass selective detector (TD–GC–MSD) technique. The mean concentrations of benzene, toluene, ethylbenzene and xylenes were, respectively, 51.5, 77.3, 17.8 and 81.6 μg/m³ in Guangzhou, 34.9, 85.9, 24.1, 95.6 μg/m³ in Macau, and 20.0, 39.1, 3.0 and 14.2 μg/m³ in Nanhai. The relative concentration distribution pattern and mutual correlation analysis indicated that in Macau BTEX were predominantly traffic-related while in Guangzhou benzene had sources other than vehicle emission. In Nanhai, both benzene and toluene had different sources other than vehicle emission. The samples collected from Guangzhou showed that BTEX had significant higher concentrations in November than those in July.     

Sensitivity of urban ozone formation to chlorine emission estimates

Recent evidence has demonstrated that chlorine radical chemistry can enhance tropospheric volatile organic compound oxidation and has the potential to enhance ozone formation in urban areas. In order to investigate the regional impacts of chlorine chemistry in southeastern Texas, preliminary estimates of atmospheric releases of atomic chlorine precursors from industrial point sources, cooling towers, water and wastewater treatment, swimming pools, tap water, reactions of chlorides in sea salt aerosols, and reactions of chlorinated organics were developed. To assess the potential implications of these estimated emissions on urban ozone formation, a series of photochemical modeling studies was conducted to examine the spatial and temporal sensitivity of ozone and a unique marker species for chlorine chemistry, 1-Chloro-3-methyl-3-butene-2-one (CMBO), to molecular chlorine emissions estimates. Based on current estimates of molecular chlorine emissions in southeastern Texas, chlorine chemistry has the potential to enhance ozone mixing ratios by up to 11–16 ppbv. Impacts varied temporally, with emissions from cooling towers primarily responsible for a morning enhancement in ozone mixing ratios and emissions from residential swimming pools for an afternoon enhancement. Maximum enhancement in CMBO mixing ratios ranged from 59 to 69 pptv.