Occurrence and removal of lidocaine,tramadol, venlafaxine,and their metabolites in German wastewater treatment plants

Purpose  

Some of the pharmaceuticals that are not extensively investigated in the aquatic environment are the anesthetic lidocaine (LDC), the analgesic tramadol (TRA), and the antidepressant venlafaxine (VEN). LDC metabolizes to 2,6-xylidine (2,6-DMA) and monoethylglycinexylidine (MEGX), TRA to O-desmethyltramadol (ODT), and VEN to O-desmethylvenlafaxine (ODV). Within this study, the distribution and behavior of these compounds in German wastewater treatment plants (WWTPs) were investigated.     

Photodegradation of quinestrol in waters and the transformation products by UV irradiation

Quinestrol is synthetic estrogen used in contraceptive and hormone replacement therapy and occasionally for treating breast cancer and prostate cancer. It can make its way into the environment through sewage discharge and waste disposal produced by human excretions. In this study, the photodegradation kinetics of quinestrol in various conditions was investigated by UV and solar irradiation. The affecting factors were studied including concentration of hydrogen peroxide, different water types, and the initial concentrations of quinestrol. Concurrently, the transformation products and presumed pathways of quinestrol in distilled water by UV irradiation were identified and proposed. The results showed that the degradation of quinestrol in both irradiation conditions followed the pseudo-first-order kinetics. More rapid degradation was observed by UV irradiation (k = 0.018 min⁻¹) than solar irradiation (k = 0.004 h⁻¹), and the photodegradation rate of quinestrol depended on the concentration of hydrogen peroxide, the initial concentration of quinestrol and water types. The transformation products of quinestrol in distilled water were identified by gas chromatography/mass spectrometry. When exposed to UV irradiation, quinestrol in aqueous solution was rapidly degraded, giving at least ten photodegradation products. The chemical structures of ten degradation products were identified on the basis of mass spectrum interpretation and literature data.     

The effects of antibiotic cocktails at environmentally relevant concentrations on the community composition and acetate biodegradation kinetics of bacterial biofilms

Antibiotics and antibacterials are present in water bodies worldwide but little is known about their effects on the biological processes often used to treat water. In this research, the effect of antibiotics on bacterial activity and community structure was investigated by growing biofilms in the presence and absence of a mixture of three compounds (sulfamethoxazole, erythromycin, and ciprofloxacin) in a continuous-flow rotating annular bioreactor fed acetate as a carbon and energy source. Steady-state, surface area-normalized substrate utilization rates for all antibiotic treatments (all at 0.33 μg L^?1, all at 3.33 μg L^?1, and 1 at 3.33 μg L^?1 with the other 2 at 0.33 μg L^?1) were similar to the control experiments. Higher attached biomass levels in the experiments with ciprofloxacin at 3.33 μg L^?1 resulted in lower steady-state biomass-normalized substrate utilization rates in comparison to other runs. Microbial community analyses via automated ribosomal intergenic spacer analysis revealed significant shifts in community structure for the experiments dosed with the highest concentrations of ciprofloxacin, suggesting that the antibiotic selected for more resistant bacterial strains. The results of this research also suggest that mixtures of antibiotics at the sub-μg L^?1 concentrations typically observed in surface waters are unlikely to affect biological process performance, at least in terms of the degradation of easily assimilable compounds. Conversely, changes to community structure and biofilm quantity might be expected with ciprofloxacin at μg L^?1 concentrations.     

Investigation of the behavior and metabolism of pharmaceutical residues during purification of contaminated ground water used for drinking water supply

Residues of phenazone-type pharmaceuticals originating from spills of a former pharmaceutical production plant have recently been detected in ground water in Berlin, Germany. The degradation pathways of phenazone, propyphenazone, and dimethylaminophenazone (DMAA) during water purification were enlightened in batch experiments with groundwater and filter material obtained from operating waterworks. For phenazone and propyphenazone a complete biological transformation into their respective metabolites 1,5-dimethyl-1,2-dehydro-3-pyrazolone (DP) and 4-(2-methylethyl)-1,5-dimethyl-1,2-dehydro-3-pyrazolone (PDP) was observed. Generally, removal of phenazone-type pharmaceutical residues during rapid sand filtration was almost exclusively caused by microorganisms only present in polluted raw water. DMAA applied to fresh filter materials was rapidly degraded into its metabolites 1-acetyl-1-methyl-2-phenylhydrazide (AMPH), acetoaminoantipyrine (AAA), formylaminoantipyrine (FAA), and 1-acetyl-1-methyl-2-dimethyloxamoyl-2-phenylhydrazide (AMDOPH). DMAA, AAA, and FAA were, however, only detected at low levels in a few samples of purified water from an operating water works. Whereas, the metabolites AMDOPH and DP were detected up to 1 μg l⁻¹. Propyphenazone was rapidly removed and AMPH, phenazone, and PDP were only measured with concentrations in the low ng l⁻¹ range. The concentrations of the metabolites DP and PDP are even higher in the purified water than in the raw water caused by their formation during degradation of phenazone and propyphenazone. Reduction of filtration velocity on an experimental filter from 5 m h⁻¹ down to 2 m h⁻¹ resulted in improved removal of phenazone, propyphenazone and their metabolites DP and PDP, respectively. AMDOPH, however, was highly persistent in all experiments independent from filtration velocities and contact times.     

Seasonal variability of formaldehyde production from photolysis of rainwater dissolved organic carbon

Photochemical production of formaldehyde (HCHO) was measured in rainwater from 13 precipitation events in Wilmington, North Carolina, USA under conditions of simulated sunlight. HCHO concentrations increased in all samples irradiated with no changes observed in dark controls. HCHO photoproduction rates were strongly correlated with dissolved organic carbon (DOC) suggesting HCHO was derived from direct or indirect photolysis of rainwater DOC. The higher photoproduction rates (0.03–2.9 μM h^?1) relative to those reported for surface waters suggests that rainwater DOC is more photolabile in terms of HCHO production than surface waters. HCHO photoproduction rates were higher in growing season (1.0 ± 1.0 μM h^?1) compared to non-growing season (0.08 ± 0.05 μM h^?1) even when rates were normalized for DOC (6.8 ± 3.6 μM h^?1 mM C^?1 versus 1.8 ± 1.0 μM h^?1 mM C^?1). The higher growing season rate may be related to seasonal differences in the composition of DOC as evidenced by differences in fluorescence per unit carbon of rainwater samples. Irradiation of C18 extracts of rainwater also produced HCHO, but at lower rates compared to corresponding whole rain samples, suggesting that hydrophyllic components of rainwater play a role in HCHO photoproduction. Our results indicate that photolysis of rainwater DOC produces significant amounts of HCHO, and possibly other low molecular weight organic compounds, likely increasing its reactivity and bioavailability.     

The influence of light exposure,water quality and vegetation on the removal of sulfonamides and tetracyclines: A laboratory-scale study

The effect of aquatic vegetation (Spyrogira sp. and Zannichellia palustris), light exposure and water quality (secondary-treated wastewater vs. ultrapure water) on the removal efficiency of six antibiotics (sulfonamides and tetracyclines) is studied in laboratory-scale reactors. After 20 d of treatment, 3–59% of sulfonamides were eliminated in the reactors exposed to light. Removal was about 10% in unplanted reactors in darkness. The elimination of tetracycline (TC) and oxytetracycline (OTC) ranged between 83% and 97% in both planted and unplanted reactors. However, in dark unplanted reactors, OTC was largely removed (88%) while only 15% of TC was eliminated. These results suggest that TC was mainly removed by photodegradation whereas biodegradation or hydrolysis process seems to be significant processes for OTC. Sulfonamides were mainly eliminated by biodegradation or indirect photodegradation processes. Pseudo-first order kinetics removal rates ranged from 0.003 and 0.007 d^?1 for Sulfamethazine and TC in the covered control reactors to 0.13 and 0.21 d^?1 for TC and OTC in the uncovered control reactors, with half-lives from 3 to 350 d. A TC photodegradation product was tentatively identified in uncovered reactors. This study highlights the important role played by light exposure in the elimination of antibiotics in polishing ponds.     

Detection,occurrence and fate of 22 psychiatric pharmaceuticals in psychiatric hospital and municipal wastewater treatment plants in Beijing,China

The liquid chromatography–electrospray ionization-tandem mass spectrometer (LC–MS/MS) method coupled with an automated solid-phase extraction procedure has been developed to identify 22 psychiatric pharmaceuticals, including seven anxiolytic-sedative-hypnotics, six antidepressants, and nine anti-schizophrenia drugs, in wastewater samples from two psychiatric hospital wastewater treatment plants (P-WWTPs) and three municipal wastewater treatment plants (M-WWTPs) in Beijing, China. Analyte recoveries from spiking experiments in the WWTP influent and effluent at three concentrations ranged from 70% to 110%, excluding sulpiride, ziprasidone, and olanzapine. Method detection limits for five, eight, and nine analytes in the WWTP influent and effluent were 20–80, 1–16, and <1 ng L^?1, respectively. High psychiatric pharmaceutical concentrations (e.g., ～942 ng L^?1oxazepam, 5552–12,782 ng L^?1 clozapine, 2762–9832 ng L^?1sulpiride, and 2030–4967 ng L^?1quetiapine) were frequently observed in P-WWTP influent compared to M-WWTPs. Although P-WWTPs typically had higher removal rates, significantly higher concentrations of the target compounds were observed in the P-WWTP secondary effluent than in the M-WWTP influent (e.g., ～752 ng L^?1oxazepam, ～8183 ng L^?1 clozapine, ～10,833 ng L^?1sulpiride, and ～1168 ng L^?1quetiapine). Thus, the discharge control of psychiatric pharmaceuticals from psychiatric hospitals requires improvement.     

Importance of wet precipitation as a removal and transport process for atmospheric water soluble carbonyls

Carbonyl compounds exist in the atmosphere as either gases or aerosols. Some of them are water soluble and known as oxidation products of biogenic and/or anthropogenic hydrocarbons. Five carbonyl compounds, glyoxal (GO), 4-oxopentanal (4-OPA), glycolaldehyde (GA), hydroxyacetone (HA) and methylglyoxal (MG) have been identified in a temporal series of 12 rain samples. The concentrations of the compounds in the samples were high at the beginning of the rain event and decreased with time to relatively low and fairly constant levels, indicating that the compounds were washed out from the atmosphere at the start of the rain event. Possibly, these compounds also existed in the cloud condensation nuclei (CCN). Wet deposition rates of the carbonyl compounds were calculated for nine samples collected during a 20 h period. The deposition rates ranged from 0 (4-OPA) to 1.2×10⁻¹ mg C m⁻² h⁻¹ (MG) with the average of 2.9×10⁻² mg C m⁻² h⁻¹. Production rates of isoprene oxidation products (GA, HA and MG) in the area surrounding the sampling site were estimated with a chemical box model. The deposition rates exceeded the production rates in most samples. This indicates that the rainfall causes a large net flux of the water soluble compounds from the atmosphere to the ground. Insoluble carbonyl compounds such as n-nonanal and n-decanal were expected to be present in the atmosphere, but were not detected in the rain during the sampling period, suggesting that an aerosol containing these insoluble compounds does not effectively act as a CCN.     

Investigations into a novel method for atmospheric polycyclic aromatic hydrocarbon monitoring

A novel analytical method for atmospheric polycyclic aromatic hydrocarbons (PAHs) was developed based on laser induced fluorescence (LIF) of samples on quartz multi-channel polydimethylsiloxane traps. A tunable dye laser with a frequency doubling crystal provided the excitation radiation, and a double monochromator with a photomultiplier tube detected emitted fluorescence. The method allowed for the rapid (<5 min), cost effective analysis of samples. Those yielding interesting results could be further analysed by direct thermal desorption-gas chromatography–mass spectrometry (TD–GC–MS, with limits of detection of ～0.3 ng m^?3), as photodegradation was minimal (<10% over 5 min irradiation). Small amounts of naphthalene photodegradation products identified by TD–GC–MS after >15 min irradiation, included phenol, benzyl alcohol and phthalic anhydride. Without any signal optimization, a LIF detection limit of ～1 μg m^?3 was established for naphthalene using a diffusion tube (diffusion rate of 2 ng s^?1) and 292 nm excitation.     

Factors influencing PM10 emissions from road pavement wear

Accelerated pavement wear is one of the major environmental disadvantages of studded tyres in northern regions and results in increased levels of PM₁₀. Measurements of PM₁₀ in a road simulator hall have been used to study the influence of pavement properties, tyre type and vehicle speed on pavement wear. The test set-up included three different pavements (one granite and two quartzite with different aggregate sizes), three different tyre types (studded, non-studded, and summer tyres) and different speeds (30–70 km h^?1). The results show that the granite pavement was more prone to PM₁₀ production compared to the quartzite pavements. Studded winter tyres yield tens of times higher PM₁₀ concentrations compared to non-studded winter tyres. Wear from summer tyres was negligible in comparison. It was also shown that wear is strongly dependent on speed; every 10 km h^?1 increase yielded an increase of the PM₁₀ concentration of 680 μg m^?3 in one of the simulator experiments.     

Heterogeneous reactivity of pyrene and 1-nitropyrene with NO2: Kinetics,product yields and mechanism

The heterogeneous reactivity of nitrogen dioxide with pyrene and 1-nitropyrene (1NP) adsorbed on silica particles has been investigated using a fast-flow-tube in the absence of light. Reactants and products were extracted from particles using pressurised fluid extraction (PFE) and concentration measurements were performed using gas chromatography/mass spectrometry (GC/MS). The pseudo-first order rate constants were obtained from the fit of the experimental decay of particulate polycyclic compound concentrations versus reaction time. Experiments were performed at three different NO₂ concentrations and second order rate constants were calculated considering the oxidant concentration. The following rate constant values were obtained at room temperature: k(NO₂ + pyrene) = (9.3 ± 2.3) × 10^?17 cm³ molecule^?1 s^?1 and k(NO₂ + 1NP) = (6.2 ± 1.5) × 10^?18 cm³ molecule^?1 s^?1, showing that the reactivity of 1NP was slower by a factor of 15 than that of pyrene. 1NP was identified as the only NO₂-initiated oxidation product of pyrene and all the three dinitropyrenes were identified in the case of the 1NP reaction. The product quantification allowed showing that the kinetics of oxidation product formation was equal to that measured for parent compounds degradation, within uncertainties, confirming the validity of the reaction kinetics measurements.     

Comparison of organic compositions in dust storm and normal aerosol samples collected at Gosan,Jeju Island,during spring 2005

To better understand the current physical and chemical properties of East Asian aerosols, an intensive observation of atmospheric particles was conducted at Gosan site, Jeju Island, South Korea during 2005 spring. Total suspended particle (TSP) samples were collected using pre-combusted quartz filters and a high-volume air sampler with the time intervals ranging from 3 h to 48 h. The kinds and amount of various organic compounds were measured in the samples using gas chromatography–mass spectrometry. Among the 99 target compounds detected, saccharides (average, 130 ± 14 ng m^?3), fatty acids (73 ± 7 ng m^?3), alcohols (41 ± 4 ng m^?3), n-alkanes (32 ± 3 ng m^?3), and phthalates (21 ± 2 ng m^?3) were found to be major compound classes with polyols/polyacids, lignin and resin products, PAHs, sterols and aromatic acids being minor. Compared to the previous results reported for 2001 late spring samples, no significant changes were found in the levels of their concentrations and compositions for 4 years, although the economy in East Asia, especially in China, has sharply expanded from 2001 to 2005. During the campaign at Gosan site, we encountered two distinct dust storm episodes with high TSP concentrations. The first dust event occurred on March 28, which was characterized by a predominance of secondary organic aerosols. The second event that occurred on the next day (March 29) was found to be characterized by primary organic aerosols associated with forest fires in Siberia/northeastern China. A significant variation in the molecular compositions, which was found within a day, suggests that the compositions of East Asian aerosols are heterogeneous due to multi-contributions from different source regions together with different pathways of long-range atmospheric transport of particles.     

High concentrations of persistent organic pollutants including PCBs,DDT, PBDEs and PFOS in little brown bats with white-nose syndrome in New York,USA

White-nose syndrome (WNS) is a condition associated with white fungal growth on ears, wings, and nose of hibernating bats; this condition has recently resulted in high bat mortality in the northeastern United States. Nevertheless, the pathogenesis of morbidity and mortality are still unknown. Elevated exposure to toxic contaminants could be a contributing factor via the consequent immunosuppression and endocrine disruption. In this study, diseased little brown bats (Myotis lucifugus) were collected from several hibernacula in eastern New York State in 2008. Fat tissues of bats were analyzed for polychlorinated biphenyls (PCBs), polybrominated diphenyl ethers (PBDEs), polybrominated biphenyls (PBBs), and organochlorine pesticides (OCPs; DDT, chlordanes, HCB, and HCH), and liver was analyzed for perfluorinated compounds (PFCs). A reference population of little brown bats, not affected by WNS, was also collected from a cave in Kentucky for the analysis of trace organic contaminants. Concentration of PCBs in fat tissues of bats from New York ranged from 1900 ng g^?1 to 35 000 ng g^?1, lipid wt, with the highest concentrations found in bats collected from caves in Albany County. High concentrations of PCBs were also found in bats from Kentucky (17 100–18 400 ng g^?1, lipid wt). Total PBDE concentrations in fat tissues ranged from 520 ng g^?1 to 10 900 ng g^?1, lipid wt, in bats from New York and from 4300 ng g^?1 to 13 000 ng g^?1, lipid wt, in bats from Kentucky. High concentrations of DDT (26 900 ng g^?1, lipid wt), chlordanes (6350 ng g^?1, lipid wt), and HCB (260 ng g^?1, lipid wt) were found in bats from New York. Concentrations of hexabromobiphenyl congener 153 (PBB 153) in bats from New York ranged from 8.6 ng g^?1 to 12 4000 ng g^?1, lipid wt. Concentrations of PFCs were on the order of a few tens to a few hundreds of nanograms per gram liver, on a wet weight basis. Overall, high concentrations of PCBs, PBDEs, DDT, and chlordanes were found in fat tissues of diseased bats from New York, although the concentrations in bats from non-diseased, reference population, from Kentucky were also high.     

Polychlorinated biphenyls hot and cold seasons distribution in see water,sediment, and fish samples in the Khour-e-Mousa (Mah-Shahr), Iran

The concentrations of polychlorinated biphenyls (PCBs) were assessed at four sites in Khour-e-Mousa (Mah-Shahr), Iran. Sea water, sediment and fish (cynoglossus bilineatus) samples were taken at each site and were analysed for PCB levels. To investigate the possible source of PCBs found in fish samples, sediments and waters were collected from four sites (D1, D2, D3, and D4) and studied. The relationship between PCB concentrations in sediment, water and fish is discussed. The results indicate that PCBs are detected in all fish samples and its concentration range from 3.2 to 102.7 μg kg^?1 dry weight and 5.4–149.7 μg kg^?1 dry weight in cold and warm seasons, respectively. The D2 and D4 sites were found to have the highest and lowest levels of PCB concentrations, respectively. Total congener PCB (CB, 28, 52, 44, 101, 149, 118, 153, 138, and 180) concentrations at the sediment samples for D1, D2, D3, and D4 sites ranged from 1.6 to 30.9 μg kg^?1 dry weight and 2.3–47.1 μg kg^?1 dry weight in cold and warm seasons, respectively. The total PCB concentrations for D2 site were found to be significantly higher than other three sites. Total water congener PCB (CB, 28, 52, 44, 101, 149, 118, 153, 138, and 180) concentrations ranged from 0.01 to 0.25 μg L^?1 and 0.02–0.39 μg L^?1 in cold and warm seasons, respectively.     

Analysis,occurrence and fate of commonly used pharmaceuticals and hormones in the Buyukcekmece Watershed,Turkey

The occurrence of 14 mostly used pharmaceuticals from different classes (antibiotics, β-blockers, non-steroidal anti-inflammatory drugs, and stimulant) and hormones in surface water in Istanbul, Turkey was investigated in this study. An important drinking water source, Buyukcekmece Lake and main rivers flowing into the lake were selected for the monitoring of the compounds. Sampling was conducted five different times in a year in order to observe seasonal changes. A rapid, robust and sensitive method using solid phase extraction and ultra-performance liquid chromatograph coupled with triple quadrupole tandem mass spectrometer was established for quantification of both pharmaceuticals and hormones. Limit of quantifications were between 0.5 and 1.1 ng L^?1. Recoveries were between 72–119% and 61–98% for ultra-pure water and for surface water, respectively. All selected compounds were detected at least once in the samples. Some pharmaceuticals were detected as high as a few of micrograms per liter levels in the rivers. Most frequently detected compounds were caffeine and antibiotics (amoxicillin, ciprofloxacin, erythromycin and sulfamethoxazole). Synthetic hormone (17α-ethynylestradiol) was detected only 4 times corresponding least detected compound in whole sampling period. Field data confirms that amoxicillin is more prone to degradation with respect to other antibiotics. Estrone and 17-β estradiol are converted to estriol by natural processes in surface water.     

Exposure to cadmium in male urban and rural workers and effects on FSH,LH and testosterone

ObjectiveThis cross-sectional study was conducted to assess the relationship between exposure to cadmium and circulating reproductive hormone levels in urban and rural male workers.Materials and MethodsUrinary cadmium, blood cadmium, luteinizing hormone (LH), follicle stimulating hormone (FSH) and testosterone were obtained from 86 non-smoking traffic policemen and 86 subjects working as roadmen in a rural area. All subjects were monitored to evaluate airborne exposure to cadmium.ResultsThe mean value of exposure to cadmium was 1.3 ng m^?3 in traffic policemen, while the mean value was less than 0.5 ng m^?3 in roadmen. The mean concentrations of urinary cadmium (1.4 vs. 0.9 μg g^?1 creatinine; p = 0.001), blood cadmium (1.1 vs. 0.7 μg l^?1; p = 0.000), FSH (2.6 vs. 3.2 μlU ml^?1; p = 0.02) and LH (2.6 vs. 3.1 μlU ml^?1; p = 0.03) were significantly different between traffic policemen and roadmen. No differences were found in the mean values of testosterone between the two groups. Multiple linear regression models showed associations between (a) urinary cadmium, airborne cadmium, working life, job category and consumption of water from water supply (b) blood cadmium, airborne cadmium and job category (c) the values of FSH and age, working life, job category, urinary cadmium and blood cadmium (d) the values of LH and both the age and working life.ConclusionThe above results must be confirmed by further studies, but they indicate the influence of exposure to the cadmium present in urban air on the circulating FSH, even at low doses.     

Biogenic emission of dimethylsulfide (DMS) from the North Yellow Sea,China and its contribution to sulfate in aerosol during summer

Seawater, atmospheric dimethylsulfide (DMS) and aerosol compounds, potentially linked with DMS oxidation, such as methanesulfonic acid (MSA) and non-sea-salt sulfate (nss-SO₄^2?) were determined in the North Yellow Sea, China during July–August, 2006. The concentrations of seawater and atmospheric DMS ranged from 2.01 to 11.79 nmol l^?1 and from 1.68 to 8.26 nmol m^?3, with average values of 6.20 nmol l^?1 and 5.01 nmol m^?3, respectively. Owing to the appreciable concentration gradient, DMS accumulated in the surface water was transferred into the atmosphere, leading to a net sea-to-air flux of 6.87 μmol m^?2 d^?1 during summer. In the surface seawater, high DMS values corresponded well with the concurrent increases in chlorophyll a levels and a significant correlation was observed between integrated DMS and chlorophyll a concentrations. In addition, the concentrations of MSA and nss-SO₄^2? measured in the aerosol samples ranged from 0.012 to 0.079 μg m^?3 and from 3.82 to 11.72 μg m^?3, with average values of 0.039 and 7.40 μg m^?3, respectively. Based on the observed MSA, nss-SO₄^2? and their ratio, the relative biogenic sulfur contribution was estimated to range from 1.2% to 11.5%, implying the major contribution of anthropogenic source to sulfur budget in the study area.     

Generation and growth of aerosols over Pune,India

The measured physical size distributions of sub-micron particles during cold season at Pune, India are analyzed to explore the characteristics of nucleation and growth properties. Preliminary analysis of aerosol size distribution in time-series shows large increase in number concentration due to nucleation events between 0800 h and 1030 h at this location. The observable quantities such as condensable vapor concentration (C), its source rate (Q), growth rate (GR) and condensable sink (CS) are estimated from the time-series evolutions of aerosol size distributions. The concentration of vapor and its source rate were about 19.8 ± 2.15 × 10⁷ molecules cm^?3 and 1.28 ± 0.084 × 10⁷ cm^?3 s^?1 respectively. The average condensation sink and growth rate were 7.1 ± 0.4 × 10^?2 s^?1 and 16.95 ± 1.86 nm h^?1 respectively during the growth period. The values are high enough to trigger the nucleation bursts and enhance subsequent growth rates of nucleation mode particles at this location. The magnitudes are in the range of those observed at New Delhi, India and much higher than those of European cities. The ratio of apparent to real nucleation rate is found to be a measure of number concentration of freshly produced particles by photo-chemical nucleation. The predicted number concentrations corresponding to measured distributions of mid-point diameter increases with the size for both 1 nm nucleated clusters and 3 nm particles. The database of all the possible event days and the event characteristics forms the basis for future works into the causes and implications of atmospheric particle formation at this location.     

Pre- and post-catalyst-, fuel-, velocity- and acceleration-dependent benzene emission data of gasoline-driven EURO-2 passenger cars and light duty vehicles

The benzene emission characteristics of six gasoline-driven EURO-2 vehicles, three passenger cars and three light duty vehicles, have been determined by time-resolved chemical ionization mass spectrometry. Aliquots of the exhaust gas were monitored pre- and post-catalyst with two independently operating mass spectrometers. Each vehicle was driven with two different fuels having benzene contents of 1 and 2 vol%. Seven driving cycles—including the European (EDC) and the US (FTP-75) driving cycle—with a total driving time of about 8800 s were studied. Herein, we discuss the average emission characteristics of the entire fleet at transient driving in the velocity range of 0–150 km h⁻¹. The conversion efficiencies of the involved catalytic systems were deduced from the pre- and post-catalyst data. On average, the vehicles showed optimal benzene conversion efficiencies (>95%) in the velocity range of 30–90 km h⁻¹. When driving below 20 or above 100 km h⁻¹ reduced benzene conversion was found (80–82%). No benzene conversion was observed when driving above 130 km h⁻¹. In contrast, the post-catalyst benzene emissions exceeded those of the untreated exhaust gas by 19–49%. Thus on an average, benzene was formed across the catalysts under these conditions. In addition, the influence of the benzene content of the gasoline on the tail-pipe emissions was also studied. The use of the gasoline with 1 vol% benzene instead of 2 vol% induced a 20–30% reduction of the post-catalyst emissions when driving below 50 km h⁻¹. The fuel effect became smaller above 100 km h⁻¹ and was even negative at high engine load (>130 km h⁻¹). Thus under these conditions, when benzene is formed across the catalyst, the amount of the emitted benzene was independent of the benzene level of the fuel.     

Kinetic aspects and identification of by-products during the ozonation of bitertanol in agricultural wastewaters

The degradation of bitertanol by ozone treatment is investigated. Solutions of bitertanol (8.4 μg mL^?1) were prepared either by dissolution of the standard or by dilution of Gaucho Blé seed loading solution and then ozonated under different conditions. Evolution of the concentrations of bitertanol and its ozonation by-products in both solutions was monitored by HPLC–UV as a function of the treatment time for a concentration of 100 g m^?3 of ozone in the inlet gas. Bitertanol degradation was found to follow a pseudo-first order reaction in both cases. However, the rate of the reaction in diluted seed loading solution was much lower (0.19 vs. 0.27 min^?1 in standard solution) and was close to the reaction rate observed in the presence of a radical scavenger, tert-butanol (0.11 min^?1). Thus, it may be suggested that additives present in the seed loading solution may play the role of radical scavengers. Study of ozone concentration in the inlet gas (from 25 to 100 g m^?3) showed that ozone degradation is also a first-order reaction with respect to ozone. Four ozonation by-products were highlighted, collected and identified by HPLC coupled with an ion trap mass spectrometer using positive electrospray ionization mode. A degradation pathway of bitertanol was finally proposed.