光催化降解水体异味物质2-MIB的机理

以水体异味物质2-甲基异莰醇(2-methylisoborneol,2-MIB)为研究对象,在紫外光(λ<380 nm)照射下,探讨TiO2(P25)对2-MIB的光催化降解特性及光化学作用机理。结果表明,UV/TiO2光催化体系可以有效去除水体异味物质2-MIB,紫外光照射60 min,对2-MIB的降解率达95%。同时研究了光催化降解体系介质pH,共存腐殖酸(HA)和过硫酸钾(K2S2O8)对UV/TiO2光催化体系降解2-MIB的影响,发现低浓度HA([HA]≤0.5 mg/L)可以提高2-MIB降解速率,当HA浓度高于0.5 mg/L,2-MIB降解反应受到抑制;同时当加入电子受体K2S2O8后,降解体系中活性物种羟基自由基(.OH)明显增加,提高了TiO2对2-MIB的降解能力。利用苯甲酸荧光光度法和POD-DPD显色法跟踪测定降解过程中羟基自由基(·OH)和过氧化氢(H2O2)的变化,表明光催化反应涉及·OH机理。     

Kinetics and mechanism of TNT degradation in TiO2 photocatalysis

The photocatalytic degradation of TNT in a circular photocatalytic reactor, using a UV lamp as a light source and TiO(2) as a photocatalyst, was investigated. The effects of various parameters such as the initial TNT concentration, and the initial pH on the TNT degradation rate of TiO(2) photocatalysis were examined. In the presence of both UV light illumination and TiO(2) catalyst, TNT was more effectively degraded than with either UV or TiO(2) alone. The reaction rate was found to obey pseudo first-order kinetics represented by the Langmuir-Hinshelwood model. In the mineralization study, TNT (30 mg/l) photocatalytic degradation resulted in an approximately 80% TOC decrease after 150 min, and 10% of acetate and 57% of formate were produced as the organic intermediates, and were further degraded. NO(-)(3) NO(-)(2), and NH(+)(4) were detected as the nitrogen byproducts from photocatalysis and photolysis, and more than 50% of the total nitrogen was converted mainly to NO(-)(3)in the photocatalysis. However, NO(-)(3) did not adsorbed on the TiO(2) surface. TNT showed higher photocatalytic degradation efficiency at neutral and basic pH.     

Photocatalytic degradation of the herbicide erioglaucine in the presence of nanosized titanium dioxide: comparison and modeling of reaction kinetics

The present work mainly deals with photocatalytic degradation of a herbicide, erioglaucine, in water in the presence of TiO2 nanoparticles (Degussa P-25) under ultraviolet (UV) light illumination (30 W). The degradation rate of erioglaucine was not so high when the photolysis was carried out in the absence of TiO2 and it was negligible in the absence of UV light. We have studied the influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO2, irradiation time and initial concentration of erioglaucine on the photodegradation efficiency of erioglaucine. A kinetic model is applied for the photocatalytic oxidation by the UV/TiO2 system. Experimental results indicated that the photocatalytic degradation process could be explained in terms of the Langmuir-Hinshelwood kinetic model. The values of the adsorption equilibrium constant, K, and the second order kinetic rate constant, k, were 0.116 ppm-1 and 0.984 ppm min-1, respectively. In this work, we also compared the reactivity between the commercial TiO2 Degussa P-25 and a rutile TiO2. The photocatalytic activities of both photocatalysts were tested using the herbicide solution. We have noticed that photodegradation efficiency was different between both of them. The higher photoactivity of Degussa P-25 compared to that of rutile TiO2 for the photodegradation of erioglaucine may be due to higher hydroxyl content, higher surface area, nano-size and crystallinity of the Degussa P-25. Our results also showed that the UV/TiO2 process with Degussa P-25 as photocatalyst was appropriate as the effective treatment method for removal of erioglaucine from a real wastewater. The electrical energy consumption per order of magnitude for photocatalytic degradation of erioglaucine was lower with Degussa P-25 than in the presence of rutile TiO2.     

Photocatalytic degradation of lignin using Pt/TiO2 as the catalyst

Photocatalytic degradation of lignin was studied with the use of catalysts TiO(2) and Pt/TiO(2). The influence of several experimental parameters, i.e. pH, catalyst dosage and illumination on lignin degradation was investigated. The results showed that application of UV irradiation alone has almost no effect on the reduction of dissolved organic carbon (DOC) and American Dye Manufacture Institute value (ADMI). However, the addition of TiO(2) and Pt/TiO(2) reduced the original DOC (251 mg l(-1)) by more than 40% within 30 min of treatment and the reaction can be simulated with pseudo-first order kinetics. Rapid degradation of lignin was observed in acidic solution using either TiO(2) or Pt/TiO(2) as the catalyst compared to high pH cases. The content of Pt in the Pt/TiO(2) catalyst is 1%. In addition, too much catalyst addition has not increased the DOC and ADMI reduction proportionally. The investigation also indicated that the photocatalytic degradation rates could be enhanced 1-6 times faster after doping TiO(2) with Pt in different pH cases. A modified Nernst type model was adopted to simulate the decoloring process using TiO(2) and Pt/TiO(2) based on the profiles of oxidation reduction potential during the photocatalytic reaction. The developed equation can be used to predict the color removal efficiency of lignin wastewater by the photocatalytic process.     

Photocatalytic oxidation of pesticide rinsate

Pesticide rinsate has been considered as one of the major threats for the environment. In this study, photocatalysts such as TiO2 and O3 were used to promote the efficiency of direct UV photolysis to prevent such wastewater pollution. Carbofuran (a carbamate pesticide) and mevinphos (an organophosphate pesticide) with a concentration of 100 mg/L were selected as the test pesticide rinsates. Parent pesticide compound, COD, and microtoxicity analysis were employed to investigate the effect of photocatalyst on the degradation efficiency of pesticide in rinsate. It was found that the photocatalytic oxidation process (UV/O3, UV/TiO2) showed much higher COD removal and microtoxicity reduction efficiency for pesticide rinsate than did direct UV photolysis under the imposed conditions, suggesting that photocatalytic oxidation processes such as UV/O3 and UV/TiO2 could be a better alternative to treat pesticide rinsate. In addition, it was noted that increasing the initial pH of mevinphos rinsate to a basic level was required to reach higher COD removal efficiency and positive microtoxicity reduction efficiency while it was not necessary for the treatment of carbofuran rinsate.     

Photocatalytic degradation of azo dyes by nitrogen-doped TiO2 nanocatalysts

This study examined the photocatalytic degradation of three azo dyes, acid orange 7 (AO7), procion red MX-5B (MX-5B) and reactive black 5 (RB5) using a new type of nitrogen-doped TiO2 nanocrystals. These newly developed doped titania nanocatalysts demonstrated high reactivity under visible light (lambda>390 nm), allowing more efficient usage of solar light. The doped titania were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Experiments were conducted to compare the photocatalytic activities of nitrogen-doped TiO2 nanocatalysts and commercially available Degussa P25 powder using both UV illumination and solar light. It is shown that nitrogen-doped TiO2 after calcination had the highest photocatalytic activity among all three catalysts tested, with 95% of AO7 decolorized in 1 h under UV illumination. The doped TiO2 also exhibited substantial photocatalytic activity under direct sunlight irradiation, with 70% of the dye color removed in 1h and complete decolorization within 3 h. Degussa P25 did not cause detectable dye decolorization under identical experimental conditions using solar light. The decrease of total organic carbon (TOC) and evolution of inorganic sulfate (SO4(2-)) ions in dye solutions were measured to monitor the dye mineralization process.     

Heterogeneous photocatalytic degradation of prometryn in aqueous solutions under UV-Vis irradiation

In this study, the heterogeneous photocatalytic degradation of prometryn using TiO(2) as photocatalyst was investigated. The main objectives of the study were: (I) to evaluate the kinetics of the pesticide disappearance, (II) to compare the photocatalytic efficiency of two different types of TiO(2), (III) to examine the influence of various parameters such as initial concentration of pesticide or catalyst and presence of oxidants (H(2)O(2) and K(2)S(2)O(8)), (IV) to evaluate the degree of mineralization and (V) to assess the detoxification efficiency of the studied processes. The experiments were carried out in a 500 ml pyrex UV reactor equipped with a 125 W high-pressure mercury lamp surrounded by a pyrex filter blocking wavelengths below 290 nm. Prometryn concentration was determined using HPLC. It was found that the degradation of the pesticide follows the first order kinetics according to the Langmuir-Hinshelwood model. Parameters like the type and concentration of the catalyst affect the degradation rate. A synergistic effect was observed when an oxidant was added in the TiO(2) suspensions increasing the reaction rate of photodegradation. In order to examine the extent of pesticide mineralization, DOC measurements were carried out. After 6h of illumination, mineralization was achieved up to almost 70%. The toxicity of the treated solution was evaluated using the Microtox test based on the luminescent bacteria Vibrio fisheri, in order to compare the acute toxicity of prometryn and its photoproducts. The detoxification efficiency was found to be dependent on the studied system and it did not follow the rate of pesticide disappearance.     

The use of oxyhalogen in photocatalytic reaction to remove o-chloroaniline in TiO2 dispersion

Photodecay of o-chloroaniline (o-ClA) in various combinations of UV sources, TiO2, and oxyhalogens was investigated. To improve the conventional photocatalytic process by using UV/TiO2, the addition of oxyhalogens (ClO3(-), BrO3(-) and IO3(-)) into UV/TiO2 system was studied and the effect in such addition is very encouraging for all the selected additives. Oxyhalogens are capable of deferring the electron-hole recombination of TiO2 which significantly improved its catalytic performance. The presence of IO3(-) in UV/TiO2 resulted in the fastest o-ClA decay among three oxhalogens at the same dosage. The decay of o-ClA in UV/TiO2/oxyhalogen process is characterized by a two-stage pseudo-kinetics, where a faster initial decay was followed by a retardation state. A mathematics model was successfully established for the prediction of the two-stage decay of o-ClA in UV/TiO2/IO3(-) with any designed [IO3(-)] concentration.     

Toxicity and biodegradability of sulfonamides and products of their photocatalytic degradation in aqueous solutions

The photocatalytic degradation of sulfacetamide, sulfathiazole, sulfamethoxazole and sulfadiazine in water solutions during their illumination of UV radiation (lambda(max) 366 nm) with TiO2 catalyst was examined. The growth-inhibition effect of sulfonamides and intermediate products theirs photodegradation was investigated in aqueous solution with the green alga Chlorella vulgaris. The biodegradability of the investigated compounds was determined in the illuminated solutions and is expressed as Biochemical Oxygen Demand. It was found that all of the investigated sulfonamides in the initial solutions were resistant to biodegradation and were toxic relative to C. vulgaris. The toxicity (EC50 values) relative to C. vulgaris increased in the following order sulfacetamide, sulfathiazole, sulfamethoxazole, sulfadiazine. All of the investigated sulfonamides undergo photocatalytic degradation. The toxicity of intermediate products of the sulfonamides degradation was significantly lower than the toxicity of sulfonamides in the initial solutions and was dependent on illumination time and degradation rate. The intermediate products of photocatalysis in contrast to the initial sulfonamides, might be mineralized using biological methods.     

Photocatalytic degradation of an organophosphorus pesticide phosalone in aqueous suspensions of titanium dioxide

The present work deals with photocatalytic degradation of an organophosphorus pesticide, phosalone, in water in the presence of TiO2 particles under UV light illumination (1000 W). The influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO2, irradiation time, stirring rate, and distance from UV source, on the photodegradation efficiency of phosalone was investigated. The degradation rate of phosalone was not high when the photolysis was carried out in the absence of TiO2 and it was negligible in the absence of UV light. The half-life (DT50) of a 20 ppm aqueous solution of phosalone was 15 min in optimized conditions. The plot of lnC (phosalone) vs. time was linear, suggesting first order reaction (K=0.0532 min(-1)). The half-life time of photomineralization in the concentration range of 7.5-20 ppm was 13.02 min. The efficiency of the method was also determined by measuring the reduction of Chemical Oxygen Demand (COD). During the mineralization under optimized conditions, COD decreased by more than 45% at irradiation time of 15 min. The photodegradation of phosalone was enhanced by addition of proper amount of hydrogen peroxide (150 ppm).     

Titanium dioxide mediated photocatalytic degradation of monochlorobenzene in aqueous phase

The reaction sequence for the photocatalytic degradation of monochlorobenzene (MCB) in UV/TiO2 process, including substrate adsorption, degradation, and mineralization, was studied. The theoretical maximum quantity of MCB that could be adsorbed onto TiO2 surface in aqueous phase was 0.18+/-0.04 micromol m(-2) of TiO2. In accordance with the upper limit of the relative surface coverage of MCB molecules to surface hydroxyls of TiO2 was around 2.2%, the water molecules as the major adjacent species near TiO2 surface would compete with MCB molecules. Increasing the initial substrate concentration to an appropriate value or enhancing the affinity between the MCB and the TiO2 surface by adjusting the solution pH would promote the photocatalytic degradation. Experimental results revealed that the neutral medium was beneficial for the degradation of MCB. In comparison, the mineralization was most improved at acidic condition. Generally, 90% of the total organic carbon (TOC) was mineralized after 240 min illumination time in the examined pH range except solution pH 11. The suppressed mineralization of MCB at solution pH 11 was ascribed to the lack of adsorption. A simplified 2-step consecutive kinetic model was used to simulate the mineralization.     

Non-degradable triazine substrates of atrazine and cyanuric acid hydrothermally and in supercritical water under the UV-illuminated photocatalytic cooperation

Strong oxidation by titanium dioxide photocatalysis can occur by photodegradation of organic contaminants in air and water. Some endocrine disruptors such as 2,4-dichlorophenoxy acetic acid (;;; ), 2,4-dichlorophenol (;;; ), nonylphenol (; ), bisphenol A (), diethyl phthalate (; ), etc. which can be neither biodegraded by bacteria nor degraded thermally can be degraded by TiO(2) photocatalytic treatment. However, incomplete photomineralization partly occurred, when TiO(2) photocatalytic degradation is employed for the treatment of certain endocrine disruptors. For example, no atrazine pesticide having triazine skeleton can be completely mineralized even by a photocatalytic procedure; the photodegradation of atrazine ultimately stops at the intermediate step of cyanuric acid, which cannot be photodegraded even after long illumination times ().In this study, the decomposition of atrazine and cyanuric acid was carried out with a device combining photocatalytic degradation in supercritical water (scH(2)O) or hydrothermal water (hyH(2)O). Atrazine and cyanuric acid can be degraded by the cooperation of either scH(2)O or hyH(2)O and UV illuminated TiO(2)-photocatalytic dispersed system under the fixed pressure of 23 MPa at 623 K or 683 K in a 120-ml Hastelloy batch reactor. The photocatalytic degradation method under high temperature and pressure has found appropriate for the photocatalytic oxidation of acetic acid and 2-chlorobiphenyl under continuous flow conditions at 160 degrees C and 20 atm (). In addition, the wet peroxide oxidation of PCBs by high temperature and pressure has been reported (). The main aims of this research are following. (i): the degradation of atrazine and cyanuric acid within the scH(2)O or hyH(2)O, (ii) the decomposition of atrazine and cyanuric acid catalyzed by TiO(2) particles under scH(2)O or hyH(2)O, and the synergistic effect for several reactions with TiO(2) and scH(2)O or hyH(2)O, and (iii) the mineralization yield of nitrogen and chlorine atoms concerning the chemical structures of atrazine or cyanuric acid (only nitrogen).     

Study on the photocatalytic degradation of glyphosate by TiO(2) photocatalyst

In this paper, the photocatalytic degradation of glyphosate selected as the deputy of organic pollutant in aqueous solution with TiO(2) powder as a photocatalyst has been studied. The effects of various parameters, such as the amount of the photocatalyst, illumination time, initial pH value, electron acceptors, metal ions, and anions on the photocatalytic degradation of glyphosate were investigated. From the studies, the best condition for the effect of the parameters on the photocatalytic degradation of glyphosate was obtained. The results show that the optimum amount of the photocatalyst used is 6.0 g l(-1) for the photocatalytic reactions. The photodegradation efficiency of glyphosate increases with the increase of the illumination time. With the addition of Fe(3+), Cu(2+), H(2)O(2), K(2)S(2)O(8) or KBrO(3), the photocatalytic degradation of glyphosate is accelerated. However, with the addition of Na(+), K(+), Mg(2+), Ca(2+), Zn(2+), Co(2+) and Ni(2+), or with the addition of trace amounts of Cl(-), Br(-), SO(4)(2-), there are no obvious effects on the reactions. Acidic or alkaline mediums are favorable for the photocatalytic degradation of glyphosate. The possible roles of the additives on the reactions and the possible mechanisms of effect were discussed.     

TiO2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有:X射线衍射光谱(XRD)、激光散射粒径分布、傅立叶变换红外光谱(FT-IR)、X射线光电子谱(XPS)和透射电子显微镜(TEM)。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂(H2O2)用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明:制备的TiO2胶体粒子平均粒径为13.8 nm(激光散法测定),光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/(L.min),平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2(含量30%)用量为0.2%(V/V),光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。     

Enhanced photocatalytic reduction reaction over Bi(3+)-TiO(2) nanoparticles in presence of formic acid as a hole scavenger

A series of Bi(3+)-doped TiO(2) (Bi(3+)-TiO(2)) catalysts with a doping concentration up to 2wt% were prepared by a sol-gel method. The prepared photocatalysts were characterized by different means to determine their chemical composition, surface structure and light absorption properties. The photocatalytic activity of different Bi(3+)-TiO(2) catalysts was evaluated in the photocatalytic reduction of nitrate in aqueous solution under UV illumination. In the experiments, formic acid was used as a hole scavenger to enhance the photocatalytic reduction reaction. The experiments demonstrated that nitrate was effectively degraded in aqueous Bi(3+)-TiO(2) suspension by more than 83% within 150min, while the pH of the solution increased from 3.19 to 5.83 due to the consumption of formic acid. The experimental results indicate that the presence of Bi(3+) in TiO(2) catalysts substantially enhances the photocatalytic reaction of nitrate reduction. It was found that the optimal dosage of 1.5wt% Bi(3+) in TiO(2) achieved the fastest reaction of nitrate reduction under the experimental condition. Bismuth ions deposit on the TiO(2) surface behaves as sites where electrons accumulate. Better separation of electrons and holes on the modified TiO(2) surface allows more efficient channeling of the charge carriers into useful reduction and oxidation reactions rather than recombination reactions. Two intermediate products of nitrite and ammonia during the reaction were also monitored to explore the possible mechanisms of photoluminescence quenching and photocatalytic reduction in the context of donor-acceptor interaction with electron trapping centers.     

Photodecomposition of o-cresol by UV-LED/TiO2 process with controlled periodic illumination

This study investigated the effect of controlled periodic illumination on the photonic efficiency and temporal decomposition behavior of o-cresol by UV/TiO2 process in a slurry reactor using light emitting diodes as the light source. Based on the same UV light intensity of 6.7 W m(-2), the calculated photonic efficiencies increased from 1.5% to 6.3% with the decreasing duty cycle from 1.0 to 0.1 possibly ascribed to the decreasing electron-hole recombination. Actually, the calculated photonic efficiency under periodic illumination at sufficiently intermittence was inferior to, but approached, those under continuous illumination at equivalent average UV light intensity. The calculated electric energy per order increased from 32 to 37 k W h m(-3)order(-1) for experiments conducted with the increasing duty cycle from 0.1 to 1.0, and the electric energy consumption decreased significantly due to the lower duty cycle and average UV light intensity. The photocatalytic decomposition of o-cresol with the UV-light emitting diodes light could be well modeled by the Langmuir-Hinshelwood kinetic equation.     

The direct photolysis and photocatalytic degradation of alachlor at different TiO2 and UV sources

Direct photolysis and photocatalytic degradations of alachlor, a widely used herbicide, were studied using three different monochromatic UV lamps (254, 300 and 350 nm) and two TiO(2) sources. Both the direct photolysis and photocatalytic degradations of alachlor follow pseudo-first-order decay kinetics. TiO(2)-P25 was found to be an effective photocatalyst compared to TiO(2)-BDH. The direct photolysis of alachlor was dominant at 254 nm even if TiO(2) was present in the solution. Among the three UV wavelengths used, the highest photocatalysis quantum yield was obtained at 300 nm. The photocatalytic degradation rate of alachlor increased with the dosages of TiO(2), but an overdose of TiO(2) would retard the reaction due to light attenuation. Photocatalytic reactions were slightly enhanced in an alkaline medium, and the different proton sources causing various degrees of rate retardation were due to the presence of the corresponding counter anions. This effect was diminished at a later stage after the reaction intermediates were formed.     

Removal of Cr(VI) and humic acid by using TiO2 photocatalysis

The removal efficiencies of Cr(VI) and HA, using a TiO(2)-mediated photocatalytic process, were investigated with variations in the pH, TiO(2) dosage and Cr(VI)/HA ratio. During the photocatalytic reaction, the total removal of Cr(VI) occurred through adsorption onto TiO(2), as well as its reduction to Cr(III). However, oxidation and adsorption were identified as important removal processes for the treatment of HA. Due to the anionic type adsorption onto TiO(2) and its acid-catalyzed photocatalytic reduction, the removal of Cr(VI) decreased with increasing pH, while that of HA increased with increasing pH. The TiO(2) dosage was also an important parameter for the removal of Cr(VI). As the TiO(2) dosage was increased to 2.5 g l(-1), the removal of Cr(VI) was continuously enhanced, but decreased at dosages above 3 g l(-1) due to the increased blockage of the incident UV light used for the photocatalytic reaction. The removal of Cr(VI) was greatly enhanced when the system contained both HA and Cr(VI) compared to Cr(VI) alone. Also, the removal of HA was greatly enhanced when the system contained both HA and Cr(VI) compared to HA alone. The removal of Cr(VI) was continuously enhanced as the HA concentration gradually increased; however, no further increase was observed above 20 mg l(-1) HA due to the increased absorption of the UV light. This result supports that the photocatalytic reaction, with illuminated TiO(2), could be applied to more effectively treat wastewater containing both Cr(VI) and HA than that containing a single species only.     

外负载Ce-TiO2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭(AC)为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明:外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

Photocatalytic degradation of dyes on a magnetically separated photocatalyst under visible and UV irradiation

A novel kind of magnetically separable photocatalyst of TiO2/SiO2/gamma-Fe2O3 (TSF) is prepared. Scanning tunnel microscope (STM) and X-ray diffractometer (XRD) were used to characterize the structure of the photocatalyst. In the TSF photocatalyst, a TiO2 shell is for photocatalysis, a gamma-Fe2O3 core as a carrier is for separation by the magnetic field and a SiO2 membrane between the TiO2 shell and the gamma-Fe2O3 core is used to weaken the adverse influence of gamma-Fe2O3 on the photocatalysis of TiO2. Three kinds of dyes, Fluoresein, Orange II and Red acid G, were used to examine the photocatalytic activity of TSF. Due to strong UV adsorption of the gamma-Fe2O3, the photocatalytic activity of TSF was lower than that of the pure TiO2. Deducting the light absorption of the gamma-Fe2O3 particles, the photocatalytic activity of TSF was found to be higher than that of the P25 under UV irradiation. On the other hand, the photocatalytic activity of TSF under visible irradiation was much lower than that of the P25 TiO2 even deducting the visible light absorption of the gamma-Fe2O3 particles. Differences in the photocatalytic mechanisms under UV and visible irradiation lead to the differences in the photodegradation characteristics of dyes on TSF. The recycled TSF exhibited a good repeatability of photocatalytic activity.